asppPortSOFCharacter

CISCO-ASPP-MIB · .1.3.6.1.4.1.9.9.55.1.1.1.1.6

MIB view Table view

Object

column Integer32

Specifies the protocol character to use to delimit
the beginning  of a frame. The valid character is 0-255
and 256 indicates the object is not configured.

Context

MIB: CISCO-ASPP-MIB
OID: .1.3.6.1.4.1.9.9.55.1.1.1.1.6
Type: column
Access: readonly
Status: current
Parent: asppPortEntry
Table: asppPortTable
Siblings: 16

Syntax

Integer32

Values & Constraints

Object Constraints

range: 0-256

Related Objects

Sibling Objects

Object	Type	Syntax	OID
asppPortProtocol Specifies type of asynchronous security protocol being used. These protocols are implemented by individual security alarm manufacturers. There is no standard protocol for alarm c…	column	Enumeration	`.1.3.6.1.4.1.9.9.55.1.1.1.1.1`
asppPortHostTimer Specifies the maximum amount of time the router will wait for a response to a terminal request from the host. It starts when a terminal request is forwarded to the host.	column	seconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.10`
asppPortConnectTimer Specifies the maximum amount of time the router will wait for the activation of the tunnel connection to the host to complete. It starts when a terminal requests a session with h…	column	seconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.11`
asppPortRetryCount Specifies the maximum number of timers a packet will be retransmitted before the connection with the terminal will be disconnected.	column	Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.12`
asppPortDelayEnq Specifies the amount of time to wait after sending a connect packet to the the terminal before sending the ENQ to initiate a session	column	milliseconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.13`
asppPortDisableEnq Specifies whether sending of ENQ to initiate a session with the terminal is disabled.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.14`
asppPortSendAck Specifies whether the router will send an ACK to acknowledge packets.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.15`
asppPortDirect Specifies whether the line mode is direct or dialed. If in direct the router will immediately send ENQ without waiting for AT commands	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.16`
asppPortDCDAlways Specifies whether DCD should always be asserted or asserted only when the connection is active.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.17`
asppPortRole Specifies the router's protocol role. primary(1) - Indicates we are attaching to the terminal or alarm panel. secondary(2) - Indicates we are attaching to the host …	column	Enumeration	`.1.3.6.1.4.1.9.9.55.1.1.1.1.2`
asppPortReceiveInterFrameTimeout Specifies the receive inter-frame-timeout period, used to delimit frames. Since all the protocols are implemented over RS-232 3-wire circuits (ie TX, RX and GND), the only general…	column	milliseconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.3`
asppPortDeviceAddressOffset Specifies the byte offset within a frame, which contains the device address. This is used when the asynchronous interface is configured to use the async generic protocol handler…	column	bytes Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.4`
asppPortEOFCharacter Specifies the protocol character to use to delimit the end of a frame. The valid character is 0-255 and 256 indicates the object is not configured.	column	Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.5`
asppPortIgnoreSequenceNumber Specifies whether the asp sequence numbers used to synchronize aspp traffic between head-end and tail-end routers should be ignored. This is enabled if there isn't a one to one c…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.7`
asppPortRspTimer Specifies the amount of time the router will wait for a response to a packet before retransmission.	column	seconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.8`
asppPortRxTimer Specifies the maximum amount of time the router will wait for a complete packet to be received. It starts when an STX character is received.	column	seconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.9`