asppPortProtocol

CISCO-ASPP-MIB · .1.3.6.1.4.1.9.9.55.1.1.1.1.1

Object

column Enumeration

Specifies type of asynchronous security protocol being
used. These protocols are implemented by individual
security alarm manufacturers. There is no standard 
protocol for alarm communications over RS-232 
interfaces.
              
asyncGeneric(5)- provides generic polled asynchronous 
                 support
              
Specific vendor support has been included for the 
following vendor's alarm equipment and protocols:
    * adplex(1)
    * ADT
        - adtPollSelect(2)
        - adtVariPoll(3)
     * diebold(4)
     * mdi(6)
     * mosec(7)
        - mosler equipment
     * gddb(8)
        - Guang Dong Development Bank 
          The protocol is similar to Burroughs 
          Poll/Select.
              
 apos(9) - Protocol support for asynchronous POS
           devices for provide credit and debit card
           authorizations to an IP attached host.

Context

MIB: CISCO-ASPP-MIB
OID: .1.3.6.1.4.1.9.9.55.1.1.1.1.1
Type: column
Access: readonly
Status: current
Parent: asppPortEntry
Table: asppPortTable
Siblings: 16

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	adplex
`2`	adtPollSelect
`3`	adtVariPoll
`4`	diebold
`5`	asyncGeneric
`6`	mdi
`7`	mosec
`8`	gddb
`9`	apos

Related Objects

Sibling Objects

Object	Type	Syntax	OID
asppPortHostTimer Specifies the maximum amount of time the router will wait for a response to a terminal request from the host. It starts when a terminal request is forwarded to the host.	column	seconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.10`
asppPortConnectTimer Specifies the maximum amount of time the router will wait for the activation of the tunnel connection to the host to complete. It starts when a terminal requests a session with h…	column	seconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.11`
asppPortRetryCount Specifies the maximum number of timers a packet will be retransmitted before the connection with the terminal will be disconnected.	column	Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.12`
asppPortDelayEnq Specifies the amount of time to wait after sending a connect packet to the the terminal before sending the ENQ to initiate a session	column	milliseconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.13`
asppPortDisableEnq Specifies whether sending of ENQ to initiate a session with the terminal is disabled.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.14`
asppPortSendAck Specifies whether the router will send an ACK to acknowledge packets.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.15`
asppPortDirect Specifies whether the line mode is direct or dialed. If in direct the router will immediately send ENQ without waiting for AT commands	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.16`
asppPortDCDAlways Specifies whether DCD should always be asserted or asserted only when the connection is active.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.17`
asppPortRole Specifies the router's protocol role. primary(1) - Indicates we are attaching to the terminal or alarm panel. secondary(2) - Indicates we are attaching to the host …	column	Enumeration	`.1.3.6.1.4.1.9.9.55.1.1.1.1.2`
asppPortReceiveInterFrameTimeout Specifies the receive inter-frame-timeout period, used to delimit frames. Since all the protocols are implemented over RS-232 3-wire circuits (ie TX, RX and GND), the only general…	column	milliseconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.3`
asppPortDeviceAddressOffset Specifies the byte offset within a frame, which contains the device address. This is used when the asynchronous interface is configured to use the async generic protocol handler…	column	bytes Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.4`
asppPortEOFCharacter Specifies the protocol character to use to delimit the end of a frame. The valid character is 0-255 and 256 indicates the object is not configured.	column	Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.5`
asppPortSOFCharacter Specifies the protocol character to use to delimit the beginning of a frame. The valid character is 0-255 and 256 indicates the object is not configured.	column	Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.6`
asppPortIgnoreSequenceNumber Specifies whether the asp sequence numbers used to synchronize aspp traffic between head-end and tail-end routers should be ignored. This is enabled if there isn't a one to one c…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.55.1.1.1.1.7`
asppPortRspTimer Specifies the amount of time the router will wait for a response to a packet before retransmission.	column	seconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.8`
asppPortRxTimer Specifies the maximum amount of time the router will wait for a complete packet to be received. It starts when an STX character is received.	column	seconds Integer32	`.1.3.6.1.4.1.9.9.55.1.1.1.1.9`