asppPortDelayEnq

CISCO-ASPP-MIB · .1.3.6.1.4.1.9.9.55.1.1.1.1.13
MIB view Table view

Object

column milliseconds Integer32 
Specifies the amount of time to wait after sending a 
connect packet to the the terminal before sending the 
ENQ to initiate a session

Context

MIB
CISCO-ASPP-MIB
OID
.1.3.6.1.4.1.9.9.55.1.1.1.1.13
Type
column
Access
readonly
Status
current
Units
milliseconds
Parent
asppPortEntry
Table
asppPortTable
Siblings
16

Syntax

milliseconds Integer32

Values & Constraints

Object Constraints
range: 1-1000

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
asppPortProtocol
Specifies type of asynchronous security protocol being used. These protocols are implemented by individual security alarm manufacturers. There is no standard protocol for alarm c…
columnEnumeration.1.3.6.1.4.1.9.9.55.1.1.1.1.1
asppPortHostTimer
Specifies the maximum amount of time the router will wait for a response to a terminal request from the host. It starts when a terminal request is forwarded to the host.
columnseconds Integer32.1.3.6.1.4.1.9.9.55.1.1.1.1.10
asppPortConnectTimer
Specifies the maximum amount of time the router will wait for the activation of the tunnel connection to the host to complete. It starts when a terminal requests a session with h…
columnseconds Integer32.1.3.6.1.4.1.9.9.55.1.1.1.1.11
asppPortRetryCount
Specifies the maximum number of timers a packet will be retransmitted before the connection with the terminal will be disconnected.
columnInteger32.1.3.6.1.4.1.9.9.55.1.1.1.1.12
asppPortDisableEnq
Specifies whether sending of ENQ to initiate a session with the terminal is disabled.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.55.1.1.1.1.14
asppPortSendAck
Specifies whether the router will send an ACK to acknowledge packets.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.55.1.1.1.1.15
asppPortDirect
Specifies whether the line mode is direct or dialed. If in direct the router will immediately send ENQ without waiting for AT commands
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.55.1.1.1.1.16
asppPortDCDAlways
Specifies whether DCD should always be asserted or asserted only when the connection is active.
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.55.1.1.1.1.17
asppPortRole
Specifies the router's protocol role. primary(1) - Indicates we are attaching to the terminal or alarm panel. secondary(2) - Indicates we are attaching to the host …
columnEnumeration.1.3.6.1.4.1.9.9.55.1.1.1.1.2
asppPortReceiveInterFrameTimeout
Specifies the receive inter-frame-timeout period, used to delimit frames. Since all the protocols are implemented over RS-232 3-wire circuits (ie TX, RX and GND), the only general…
columnmilliseconds Integer32.1.3.6.1.4.1.9.9.55.1.1.1.1.3
asppPortDeviceAddressOffset
Specifies the byte offset within a frame, which contains the device address. This is used when the asynchronous interface is configured to use the async generic protocol handler…
columnbytes Integer32.1.3.6.1.4.1.9.9.55.1.1.1.1.4
asppPortEOFCharacter
Specifies the protocol character to use to delimit the end of a frame. The valid character is 0-255 and 256 indicates the object is not configured.
columnInteger32.1.3.6.1.4.1.9.9.55.1.1.1.1.5
asppPortSOFCharacter
Specifies the protocol character to use to delimit the beginning of a frame. The valid character is 0-255 and 256 indicates the object is not configured.
columnInteger32.1.3.6.1.4.1.9.9.55.1.1.1.1.6
asppPortIgnoreSequenceNumber
Specifies whether the asp sequence numbers used to synchronize aspp traffic between head-end and tail-end routers should be ignored. This is enabled if there isn't a one to one c…
columnSNMPv2-TCTruthValue.1.3.6.1.4.1.9.9.55.1.1.1.1.7
asppPortRspTimer
Specifies the amount of time the router will wait for a response to a packet before retransmission.
columnseconds Integer32.1.3.6.1.4.1.9.9.55.1.1.1.1.8
asppPortRxTimer
Specifies the maximum amount of time the router will wait for a complete packet to be received. It starts when an STX character is received.
columnseconds Integer32.1.3.6.1.4.1.9.9.55.1.1.1.1.9