prtExVc2TxBitCode
RAD-MIB ·
.1.3.6.1.4.1.164.3.2.3.2.5.1.20
Object
column
r/w
OctetString
- - - For MP & FCD - - -
This object represents 4 parameters, by 2 Octets :
Tx D Bit Code-MSB nibble,
Tx C Bit Code- nibble,
Tx B Bit Code- nibble,
Tx A Bit Code-LSB nibble.
Each nibble:
0 hex = 0000 = Not Applicable
1 hex = 0001 = M lead
2 hex = 0010 = M lead inverse
3 hex = 0011 = Reverse Polarity
4 hex = 0100 = Metering Pulse
5 hex = 0101 = Forced 1
6 hex = 0110 = Forced 0
7-F hex - not used (invalid values)
This object will be RO if prtExVc2SigProfile is NOT manual.
- - - For WR II - - -
This object represents the following 4 parameters by 2 Octets:
1. On/Off hook signaling transmission mode from the FXS towards the T1/E1 (MSB nibble 1).
2. Default signaling bits that are not in use (nibble 2).
3. Ring Detection signaling transmission mode from the FXO towards the T1/E1(nibble 3).
4. M (Mouth) Signaling transmission mode from the E&M towards the T1/E1(LSB nibble 4).
Each nibble:
---------------------------------------------------------------------------------------
Value On/Off Hook Default sig. Ring Detect. M (Mouth)
---------------------------------------------------------------------------------------
0 hex = 0000 Not Applicable Not Applicable. Not Applicable Not Applicable
1 hex = 0001 Tx A bit Values 1-3 are Tx A bit Tx A bit
2 hex = 0010 Tx A bit inverse for On/Off Hook Tx A bit inv. Tx A bit inv.
3 hex = 0011 Tx B bit A,B,A Inv,B Inv. Tx B bit Tx B bit
4 hex = 0100 Tx B bit inverse Values 4-7 are Tx B bit inv. Tx B bit inv.
5 hex = 0101 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid
6 hex = 0110 not Used-invalid A, A Inverse. not Used-invalid not Used-invalid
7 hex = 0111 not Used-invalid not Used-invalid not Used-invalid
8 hex = 1000 not Used-invalid Values 8-11 are not Used-invalid not Used-invalid
9 hex = 1001 not Used-invalid for On/Off Hook not Used-invalid not Used-invalid
A hex = 1010 not used-invalid B, B Inverse. not Used-invalid not Used-invalid
B hex = 1011 not used-invalid The Bits order: not Used-invalid not Used-invalid
C-F hex not used-invalid ABCD not Used-invalid not Used-invalid
Default value: 11 11
Context
- MIB
- RAD-MIB
- OID
.1.3.6.1.4.1.164.3.2.3.2.5.1.20- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- prtVc2CnfgEntry
- Table
- prtVc2CnfgTable
- Siblings
- 39
Syntax
OctetString
Values & Constraints
Enumerated Values
2 | restoreT1secFast |
3 | restoreT10sec62411 |
4 | ccittE1 |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| prtVc2CnfgIdx This attribute indicates the Idx of the Cnfg (1..100) being
accessed.
Idx 255 relates to the TmpCnfg | column | Integer32 | .1.3.6.1.4.1.164.3.2.3.2.5.1.1 |
| prtExVc2Oos This object is equal for all the ports in the specific card
because of HW limitations | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.10 |
| prtExVc2LinkTo deprecated This attribute indicates the slot of the ML card to which
the VC card is mapped.
STATUS deprecated - this object is replaced by prtGenCnfgLinkToSlot
and prtGenCnfgLinkToPort. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.11 |
| prtExVc2OperMode This object indicates the operation mode of the port.
normal = bi-directional (Tx/Rx)
unidirectRx = unidirectional Rx.
broadcast = Tx upon request. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.12 |
| prtExVc2SigProfile This object indicates the Signaling Profile of the port.
notApplicable - for VC-2 family and when
prtExVc2Sig=noSignaling(1)
p1 = profile 1
p2 = profile 2
p3 = pro… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.13 |
| prtExVc2CallEnable This object indicates the Enabled Call direction.
notApplicable - for all cards except VC-2/R2.
both - incoming + outgoing. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.14 |
| prtExVc2R2Delay This object indicates the R2 Delay.
notApplicable - for all cards except VC-2/R2. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.15 |
| prtExVc2CasStd This object indicates the CAS (Channel Associated Signaling)
Standard.
notApplicable - for all cards except VC-2/R2. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.16 |
| prtExVc2EchoCanceler Echo canceler activation.
notApplicable - for VC-2 and VC-6 cards. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.17 |
| prtExVc2IfType Interface Type. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.18 |
| prtExVc2Encoding Voice Encoding Mode.
linear - is relevant only for the ports of VC-16A card. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.19 |
| prtVc2SltIdx This attribute indicates a unique slot position where
the card is inserted.
For Stand Alone products like WR: notApplicable (255) | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.2 |
| prtExVc2RxBitOutput - - - For MP (VC-Q card only) & FCD - - -
This object represents 3 parameters by 2 Octets:
Spare -MSB nibble, always=0 hex
E Lead Output - nibble,
Reverse Polar… | column | OctetString | .1.3.6.1.4.1.164.3.2.3.2.5.1.21 |
| prtExVc2MeterRate This entry is applicable only for VC-6A/FXO, VC-6A/FXS, VC-8/FXO,
VC-8/FXS, VC-16/FXO and VC-16/FXS.
Meter Rate means rate of Call Meter in Public Phones, in KHz units.
For some c… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.22 |
| prtExVc2IfSignaling This entry is applicable only for VC-6A, VC-6AG, VC-8/FXO, VC-8/FXS,
VC-16/FXO and VC-16/FXS cards.
Interface Analog Signaling.
Must be the same for all card's ports.
loopStart - … | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.23 |
| prtExVc2SeizeAck This parameter shows whether the device will acknowledge
a seize signal (On/Off Hook).
When the value is set to yes(3) & the device receives an on/off hook signal
it will transmit… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.24 |
| prtExVc2EandMType This is the signaling type on the E&M analog side.
The analog signaling includes voltage, no. of pins and other parameters. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.25 |
| prtExVc2RemType Remote Type.
Applicable for VC-6A/4LB card &
for IPMUX-1E Far End Type - E1,T1(T1-ESF) or T1-D4 . | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.26 |
| prtExVc2ConvTime Conversation Time in minutes.
Applicable for VC-6A/4LB card. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.27 |
| prtExVc2SigFeedback Signaling Feedback.
Applicable for VC-8/FXO and VC-16/FXO cards. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.28 |
| prtExVc2EchoCancelerModule This parameter indicates whether Echo canceler module exists for this port. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.29 |
| prtVc2PrtIdx A unique identifier of the port, within the card.
For MP-2100/2200 card ports, Web Ranger and FCD-IP Voice ports
the values will be:
exPrt1 (1)
exPrt2 (2)
exPrt3 (… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.5.1.3 |
| prtExVc2ReversePolarity This object Enables/Disables Reverse Polarity for this port. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.30 |
| prtExVc2RingerFrequency This object selects the Ringer Frequency (Hz) for this port. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.31 |
| prtExVc2SigService Signaling Service.
advanced - is relevant only for ports of VC-8, VC-16 FXS cards.
It is used for Signaling Services of V5.1 or R2. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.32 |
| prtExVc2CallerIdEnable This object Enables/Disables Receiving the Caller Id number from the
remote side, for this port/channel. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.33 |
| prtExVc2CompressMethod This object is applicable only when prtExVc2Encoding=adpcm.
It defines which method is used for Compression.
g726 - for 4 bits (the standard method).
g726 - for 3 bits. It is espe… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.34 |
| prtExVc2ObMode This object defines the Net operation mode of the Omni-Bus card's port.
pointToPoint - only 2 end-point ports talk; like any other voice card
omniBus - many talk and listen. … | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.35 |
| prtExVc2VAD This object defines whether Voice Activation Detector (VAD)
will be On or Off.
off - will be usually selected when a Modem is connected
to the port; not a phone.
not… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.36 |
| prtExVc2NoiseLevelForVAD This object defines the Level of Noise on the line,
the Voice Activation Detector (VAD) will have to deal with.
notApplicable - when prtExVc2VAD=off. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.37 |
| prtExVc2WesternSigMode This object defines the Western Signaling Mode.
detector - detects signal and passes it as is.
generator - generates the signal.
notApplicable - when Western HW is not installed. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.38 |
| prtExVc2BusProtectionPoint This object defines if the port is Bus Protection Point or not.
notApplicable - when prtExVc2DspMode=pointToPoint.
When we have a chain of devices where the edge devices ports are… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.39 |
| prtExVc2Connect This attribute indicates whether the port should be
considered in any of the mux algorithms. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.4 |
| prtExVc2ImpedanceStandard This object defines the Standard used for Impedance.
-G.712 - 600 Ohm - used in USA and other countries.
-Q552/ETSI - used in some countries in Europe
-Q522/Italy - used in Italy. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.40 |
| prtExVc2TransGain Transmit gain in dBm.
For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8
VC-4/Omni and VC-16 cards, the units will be 0.1dBm because
valid values can be in 0.5dBm steps. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.5.1.5 |
| prtExVc2ReceiveGain Receive gain in dBm.
For ports of MP-104/204, MP-2100/2200 VC-6A, VC-6AG, VC-8
VC-4/Omni and VC-16 cards, the units will be 0.1dBm because
valid values can be in 0.5dBm steps. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.3.2.3.2.5.1.6 |
| prtExVc2Wire For some cards, this object is equal for all the ports in the specific
card because of HW limitations.
For FXO & FXS this parameter is not applicable. | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.7 |
| prtExVc2CodingLaw This attribute indicates the Method/Law for decoding/encoding the voice
information.
aLaw(1) is the standard Law for E1 links.
uLaw(2) is the standard Law for T1 links.
… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.8 |
| prtExVc2Sig This attribute indicates the method for decoding/encoding the signaling
information(on/off hook).
noSignaling (1) - not using signaling (only voice).
robbedBitMultiFrame(2)… | column | Enumeration | .1.3.6.1.4.1.164.3.2.3.2.5.1.9 |