olsrv2PHoldTime
OLSRv2-MIB ·
.1.3.6.1.2.1.219.1.1.11
Object
olsrv2PHoldTime corresponds to
P_HOLD_TIME of OLSRv2 and represents the period
after receipt of a message that is processed by
this router for which that information is recorded,
in order that the message is not processed again
if received again.
Guidance for setting this object may be found
in Section 5 of the OLSRv2 specification (RFC 7181),
which indicates that:
o olsrv2PHoldTime > 0
o This parameter SHOULD be greater
than the maximum difference in time that a
message may take to traverse the MANET,
taking into account any message forwarding
jitter as well as propagation, queuing,
and processing delays.
This object is persistent, and when written,
the entity SHOULD save the change to
non-volatile storage.
Context
- MIB
- OLSRv2-MIB
- OID
.1.3.6.1.2.1.219.1.1.11- Type
- scalar
- Access
- readwrite
- Status
- current
- Units
- milliseconds
- Parent
- olsrv2ConfigurationGroup
- Siblings
- 18
Syntax
milliseconds SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| olsrv2AdminStatus The configured status of the OLSRv2 process
on this device. 'enabled(1)' means that
OLSRv2 is configured to run on this device.
'disabled(2)' mean that the OLSRv2 process
is conf… | scalar | Olsrv2StatusTC | .1.3.6.1.2.1.219.1.1.1 |
| olsrv2RxHoldTime olsrv2RxHoldTime corresponds to
RX_HOLD_TIME of OLSRv2 and represents the period
after receipt of a message by the appropriate OLSRv2
interface of this router for which that infor… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.10 |
| olsrv2FHoldTime olsrv2FHoldTime corresponds to
F_HOLD_TIME of OLSRv2 and represents the period
after receipt of a message that is forwarded by this
router for which that information is recorded, … | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.12 |
| olsrv2TpMaxJitter olsrv2TpMaxJitter corresponds to
TP_MAXJITTER of OLSRv2 and represents the value
of MAXJITTER used in RFC 5148 for periodically
generated TC messages sent by this router.
… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.13 |
| olsrv2TtMaxJitter olsrv2TtMaxJitter corresponds to
TT_MAXJITTER of OLSRv2 and represents the value
of MAXJITTER used in RFC 5148 for externally
triggered TC messages sent by this router.
… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.14 |
| olsrv2FMaxJitter olsrv2FMaxJitter corresponds to
F_MAXJITTER of OLSRv2 and represents the
default value of MAXJITTER used in RFC 5148 for
messages forwarded by this router.
For constrai… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.15 |
| olsrv2TcHopLimit olsrv2TcHopLimit corresponds to
TC_HOP_LIMIT of OLSRv2.
Guidance for setting this object may be found
in Section 5 of the OLSRv2 specification (RFC 7181),
which indicat… | scalar | hops Unsigned32 | .1.3.6.1.2.1.219.1.1.16 |
| olsrv2WillRouting olsrv2WillRouting corresponds to
WILL_ROUTING of OLSRv2.
Guidance for setting this object may be found
in Section 5 of the OLSRv2 specification (RFC 7181),
which indica… | scalar | WillingnessTC | .1.3.6.1.2.1.219.1.1.17 |
| olsrv2WillFlooding olsrv2WillFlooding corresponds to
WILL_FLOODING of OLSRv2.
Guidance for setting this object may be found
in Section 5 of the OLSRv2 specification (RFC 7181),
which indi… | scalar | WillingnessTC | .1.3.6.1.2.1.219.1.1.18 |
| olsrv2LinkMetricType olsrv2LinkMetricType corresponds to
LINK_METRIC_TYPE of OLSRv2.
If olsrv2LinkMetricType changes, then all
link metric information recorded by this router
is invalid. T… | scalar | IANA-OLSRv2-LINK-METRIC-TYPE-MIBIANAolsrv2LinkMetricTypeTC | .1.3.6.1.2.1.219.1.1.19 |
| olsrv2InterfaceTable The olsrv2InterfaceTable describes the OLSRv2
status on the NHDP interfaces of this router.
As such, this table augments the nhdpInterfaceTable
defined in the NHDP-MIB (RFC 6779).… | table | - | .1.3.6.1.2.1.219.1.1.2 |
| olsrv2OrigIpAddrType The type of the olsrv2OrigIpAddr, as defined
in the InetAddress MIB module (RFC 4001).
Only the values 'ipv4(1)' and
'ipv6(2)' are supported. | scalar | Enumeration | .1.3.6.1.2.1.219.1.1.3 |
| olsrv2OrigIpAddr The router's originator address. An address that
is unique (within the MANET) to this router.
This object is persistent, and when written,
the entity SHOULD save the c… | scalar | OctetString | .1.3.6.1.2.1.219.1.1.4 |
| olsrv2OHoldTime olsrv2OHoldTime corresponds to
O_HOLD_TIME of OLSRv2, and represents the
time for which a recently used and replaced
originator address is used to recognize the router's
own messa… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.5 |
| olsrv2TcInterval olsrv2TcInterval corresponds to
TC_INTERVAL of OLSRv2 and represents the
maximum time between the transmission of
two successive TC messages by this router.
Guidance fo… | scalar | milliseconds Olsrv2TimeValueCompressedForm32TC | .1.3.6.1.2.1.219.1.1.6 |
| olsrv2TcMinInterval olsrv2TcMinInterval corresponds to
TC_MIN_INTERVAL of OLSRv2 and represents
the minimum interval between transmission of
two successive TC messages by this router.
Guid… | scalar | milliseconds Olsrv2TimeValueCompressedForm32TC | .1.3.6.1.2.1.219.1.1.7 |
| olsrv2THoldTime olsrv2THoldTime corresponds to
T_HOLD_TIME of OLSRv2 and is used as the
minimum value in the TLV with
Type = VALIDITY_TIME included in all
TC messages sent by this router.
… | scalar | milliseconds Olsrv2TimeValueCompressedForm32TC | .1.3.6.1.2.1.219.1.1.8 |
| olsrv2AHoldTime olsrv2AHoldTime corresponds to
A_HOLD_TIME of OLSRv2 and represents
the period during which TC messages are sent
after they no longer have any advertised
information to report, bu… | scalar | milliseconds Olsrv2TimeValueCompressedForm32TC | .1.3.6.1.2.1.219.1.1.9 |