olsrv2OHoldTime
OLSRv2-MIB ·
.1.3.6.1.2.1.219.1.1.5
Object
olsrv2OHoldTime corresponds to
O_HOLD_TIME of OLSRv2, and represents the
time for which a recently used and replaced
originator address is used to recognize the router's
own messages.
Guidance for setting this object may be found
in Section 5 of the OLSRv2 specification (RFC 7181),
which indicates that:
o olsrv2OHoldTime > 0
This object is persistent, and when written,
the entity SHOULD save the change to
non-volatile storage.
Context
- MIB
- OLSRv2-MIB
- OID
.1.3.6.1.2.1.219.1.1.5- Type
- scalar
- Access
- readwrite
- Status
- current
- Units
- milliseconds
- Parent
- olsrv2ConfigurationGroup
- Siblings
- 18
Syntax
milliseconds SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| olsrv2AdminStatus The configured status of the OLSRv2 process
on this device. 'enabled(1)' means that
OLSRv2 is configured to run on this device.
'disabled(2)' mean that the OLSRv2 process
is conf… | scalar | Olsrv2StatusTC | .1.3.6.1.2.1.219.1.1.1 |
| olsrv2RxHoldTime olsrv2RxHoldTime corresponds to
RX_HOLD_TIME of OLSRv2 and represents the period
after receipt of a message by the appropriate OLSRv2
interface of this router for which that infor… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.10 |
| olsrv2PHoldTime olsrv2PHoldTime corresponds to
P_HOLD_TIME of OLSRv2 and represents the period
after receipt of a message that is processed by
this router for which that information is recorded,
… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.11 |
| olsrv2FHoldTime olsrv2FHoldTime corresponds to
F_HOLD_TIME of OLSRv2 and represents the period
after receipt of a message that is forwarded by this
router for which that information is recorded, … | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.12 |
| olsrv2TpMaxJitter olsrv2TpMaxJitter corresponds to
TP_MAXJITTER of OLSRv2 and represents the value
of MAXJITTER used in RFC 5148 for periodically
generated TC messages sent by this router.
… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.13 |
| olsrv2TtMaxJitter olsrv2TtMaxJitter corresponds to
TT_MAXJITTER of OLSRv2 and represents the value
of MAXJITTER used in RFC 5148 for externally
triggered TC messages sent by this router.
… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.14 |
| olsrv2FMaxJitter olsrv2FMaxJitter corresponds to
F_MAXJITTER of OLSRv2 and represents the
default value of MAXJITTER used in RFC 5148 for
messages forwarded by this router.
For constrai… | scalar | milliseconds SNMPv2-SMIUnsigned32 | .1.3.6.1.2.1.219.1.1.15 |
| olsrv2TcHopLimit olsrv2TcHopLimit corresponds to
TC_HOP_LIMIT of OLSRv2.
Guidance for setting this object may be found
in Section 5 of the OLSRv2 specification (RFC 7181),
which indicat… | scalar | hops Unsigned32 | .1.3.6.1.2.1.219.1.1.16 |
| olsrv2WillRouting olsrv2WillRouting corresponds to
WILL_ROUTING of OLSRv2.
Guidance for setting this object may be found
in Section 5 of the OLSRv2 specification (RFC 7181),
which indica… | scalar | WillingnessTC | .1.3.6.1.2.1.219.1.1.17 |
| olsrv2WillFlooding olsrv2WillFlooding corresponds to
WILL_FLOODING of OLSRv2.
Guidance for setting this object may be found
in Section 5 of the OLSRv2 specification (RFC 7181),
which indi… | scalar | WillingnessTC | .1.3.6.1.2.1.219.1.1.18 |
| olsrv2LinkMetricType olsrv2LinkMetricType corresponds to
LINK_METRIC_TYPE of OLSRv2.
If olsrv2LinkMetricType changes, then all
link metric information recorded by this router
is invalid. T… | scalar | IANA-OLSRv2-LINK-METRIC-TYPE-MIBIANAolsrv2LinkMetricTypeTC | .1.3.6.1.2.1.219.1.1.19 |
| olsrv2InterfaceTable The olsrv2InterfaceTable describes the OLSRv2
status on the NHDP interfaces of this router.
As such, this table augments the nhdpInterfaceTable
defined in the NHDP-MIB (RFC 6779).… | table | - | .1.3.6.1.2.1.219.1.1.2 |
| olsrv2OrigIpAddrType The type of the olsrv2OrigIpAddr, as defined
in the InetAddress MIB module (RFC 4001).
Only the values 'ipv4(1)' and
'ipv6(2)' are supported. | scalar | Enumeration | .1.3.6.1.2.1.219.1.1.3 |
| olsrv2OrigIpAddr The router's originator address. An address that
is unique (within the MANET) to this router.
This object is persistent, and when written,
the entity SHOULD save the c… | scalar | OctetString | .1.3.6.1.2.1.219.1.1.4 |
| olsrv2TcInterval olsrv2TcInterval corresponds to
TC_INTERVAL of OLSRv2 and represents the
maximum time between the transmission of
two successive TC messages by this router.
Guidance fo… | scalar | milliseconds Olsrv2TimeValueCompressedForm32TC | .1.3.6.1.2.1.219.1.1.6 |
| olsrv2TcMinInterval olsrv2TcMinInterval corresponds to
TC_MIN_INTERVAL of OLSRv2 and represents
the minimum interval between transmission of
two successive TC messages by this router.
Guid… | scalar | milliseconds Olsrv2TimeValueCompressedForm32TC | .1.3.6.1.2.1.219.1.1.7 |
| olsrv2THoldTime olsrv2THoldTime corresponds to
T_HOLD_TIME of OLSRv2 and is used as the
minimum value in the TLV with
Type = VALIDITY_TIME included in all
TC messages sent by this router.
… | scalar | milliseconds Olsrv2TimeValueCompressedForm32TC | .1.3.6.1.2.1.219.1.1.8 |
| olsrv2AHoldTime olsrv2AHoldTime corresponds to
A_HOLD_TIME of OLSRv2 and represents
the period during which TC messages are sent
after they no longer have any advertised
information to report, bu… | scalar | milliseconds Olsrv2TimeValueCompressedForm32TC | .1.3.6.1.2.1.219.1.1.9 |