olsrv2AdminStatus

OLSRv2-MIB · .1.3.6.1.2.1.219.1.1.1

Object

scalar r/w Olsrv2StatusTC

The configured status of the OLSRv2 process
on this device.  'enabled(1)' means that
OLSRv2 is configured to run on this device.
'disabled(2)' mean that the OLSRv2 process
is configured off.
          
Operation of the OLSRv2 protocol
requires the operation of the Neighborhood
Discovery Protocol (RFC 6130).  Hence, this
object cannot have a status of 'enabled'
unless at least one interface on the device
is a MANET interface with NHDP enabled on that
interface.  If a network manager attempts to
set this object to 'enabled' when no interfaces
on this device have NHDP enabled, the device
MUST fail the set with inconsistentValue.
If all device interfaces running NHDP become
disabled or removed, then the
olsrv2AdminStatus MUST be 'disabled'.
          
If the network manager, or other means, sets
this object to 'disabled', then the associated
interface specific objects, i.e., the
olsrv2InterfaceAdminStatus objects MUST all
be 'disabled'.
          
This object is persistent, and when written,
the entity SHOULD save the change to
non-volatile storage.

Context

MIB: OLSRv2-MIB
OID: .1.3.6.1.2.1.219.1.1.1
Type: scalar
Access: readwrite
Status: current
Parent: olsrv2ConfigurationGroup
Siblings: 18

Syntax

Olsrv2StatusTC

Source: Olsrv2StatusTC
Base type: Enumeration

Values & Constraints

Type Values

`1`	enabled
`2`	disabled

Related Objects

Sibling Objects

Object	Type	Syntax	OID
olsrv2RxHoldTime olsrv2RxHoldTime corresponds to RX_HOLD_TIME of OLSRv2 and represents the period after receipt of a message by the appropriate OLSRv2 interface of this router for which that infor…	scalar	milliseconds SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.219.1.1.10`
olsrv2PHoldTime olsrv2PHoldTime corresponds to P_HOLD_TIME of OLSRv2 and represents the period after receipt of a message that is processed by this router for which that information is recorded, …	scalar	milliseconds SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.219.1.1.11`
olsrv2FHoldTime olsrv2FHoldTime corresponds to F_HOLD_TIME of OLSRv2 and represents the period after receipt of a message that is forwarded by this router for which that information is recorded, …	scalar	milliseconds SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.219.1.1.12`
olsrv2TpMaxJitter olsrv2TpMaxJitter corresponds to TP_MAXJITTER of OLSRv2 and represents the value of MAXJITTER used in RFC 5148 for periodically generated TC messages sent by this router. …	scalar	milliseconds SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.219.1.1.13`
olsrv2TtMaxJitter olsrv2TtMaxJitter corresponds to TT_MAXJITTER of OLSRv2 and represents the value of MAXJITTER used in RFC 5148 for externally triggered TC messages sent by this router. …	scalar	milliseconds SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.219.1.1.14`
olsrv2FMaxJitter olsrv2FMaxJitter corresponds to F_MAXJITTER of OLSRv2 and represents the default value of MAXJITTER used in RFC 5148 for messages forwarded by this router. For constrai…	scalar	milliseconds SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.219.1.1.15`
olsrv2TcHopLimit olsrv2TcHopLimit corresponds to TC_HOP_LIMIT of OLSRv2. Guidance for setting this object may be found in Section 5 of the OLSRv2 specification (RFC 7181), which indicat…	scalar	hops Unsigned32	`.1.3.6.1.2.1.219.1.1.16`
olsrv2WillRouting olsrv2WillRouting corresponds to WILL_ROUTING of OLSRv2. Guidance for setting this object may be found in Section 5 of the OLSRv2 specification (RFC 7181), which indica…	scalar	WillingnessTC	`.1.3.6.1.2.1.219.1.1.17`
olsrv2WillFlooding olsrv2WillFlooding corresponds to WILL_FLOODING of OLSRv2. Guidance for setting this object may be found in Section 5 of the OLSRv2 specification (RFC 7181), which indi…	scalar	WillingnessTC	`.1.3.6.1.2.1.219.1.1.18`
olsrv2LinkMetricType olsrv2LinkMetricType corresponds to LINK_METRIC_TYPE of OLSRv2. If olsrv2LinkMetricType changes, then all link metric information recorded by this router is invalid. T…	scalar	IANA-OLSRv2-LINK-METRIC-TYPE-MIBIANAolsrv2LinkMetricTypeTC	`.1.3.6.1.2.1.219.1.1.19`
olsrv2InterfaceTable The olsrv2InterfaceTable describes the OLSRv2 status on the NHDP interfaces of this router. As such, this table augments the nhdpInterfaceTable defined in the NHDP-MIB (RFC 6779).…	table	-	`.1.3.6.1.2.1.219.1.1.2`
olsrv2OrigIpAddrType The type of the olsrv2OrigIpAddr, as defined in the InetAddress MIB module (RFC 4001). Only the values 'ipv4(1)' and 'ipv6(2)' are supported.	scalar	Enumeration	`.1.3.6.1.2.1.219.1.1.3`
olsrv2OrigIpAddr The router's originator address. An address that is unique (within the MANET) to this router. This object is persistent, and when written, the entity SHOULD save the c…	scalar	OctetString	`.1.3.6.1.2.1.219.1.1.4`
olsrv2OHoldTime olsrv2OHoldTime corresponds to O_HOLD_TIME of OLSRv2, and represents the time for which a recently used and replaced originator address is used to recognize the router's own messa…	scalar	milliseconds SNMPv2-SMIUnsigned32	`.1.3.6.1.2.1.219.1.1.5`
olsrv2TcInterval olsrv2TcInterval corresponds to TC_INTERVAL of OLSRv2 and represents the maximum time between the transmission of two successive TC messages by this router. Guidance fo…	scalar	milliseconds Olsrv2TimeValueCompressedForm32TC	`.1.3.6.1.2.1.219.1.1.6`
olsrv2TcMinInterval olsrv2TcMinInterval corresponds to TC_MIN_INTERVAL of OLSRv2 and represents the minimum interval between transmission of two successive TC messages by this router. Guid…	scalar	milliseconds Olsrv2TimeValueCompressedForm32TC	`.1.3.6.1.2.1.219.1.1.7`
olsrv2THoldTime olsrv2THoldTime corresponds to T_HOLD_TIME of OLSRv2 and is used as the minimum value in the TLV with Type = VALIDITY_TIME included in all TC messages sent by this router. …	scalar	milliseconds Olsrv2TimeValueCompressedForm32TC	`.1.3.6.1.2.1.219.1.1.8`
olsrv2AHoldTime olsrv2AHoldTime corresponds to A_HOLD_TIME of OLSRv2 and represents the period during which TC messages are sent after they no longer have any advertised information to report, bu…	scalar	milliseconds Olsrv2TimeValueCompressedForm32TC	`.1.3.6.1.2.1.219.1.1.9`