aluRS232Duplex
ALU-PORT-MIB ·
.1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.6
Object
column
r/w
Enumeration
aluRS232Duplex configures the duplex method of the interface to
half or full duplex.
full is not allowed while aluRS232MultiDrop is slave.
half is not valid while the sub-channel is aluRS232SocketEntry.
Context
- MIB
- ALU-PORT-MIB
- OID
.1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.6- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- aluRS232Entry
- Table
- aluRS232Table
- Siblings
- 39
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | fullDuplex |
2 | halfDuplex |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| aluRS232RowStatus aluRS232RowStatus controls the creation and deletion of
row entries in the aluRS232Table.
For row creation, the manager has to first calculate the
tmnxPortPortID based on the TiM… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.1 |
| aluRS232CharacterLength The aluRS232CharacterLength specifies the character length.
Parameter is only valid while the port is configured for asynchronous operation.
The value of aluRS232Ch… | column | Integer32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.10 |
| aluRS232Parity The aluRS232Parity specifies the parity type.
Parameter is only valid while the port is configured for asynchronous operation.
The value of aluRS232CharacterLength … | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.11 |
| aluRS232StopBits The aluRS232StopBits specifies the stop bits.
Parameter is only valid while the port is configured for asynchronous operation.
The value of aluRS232CharacterLength … | column | Integer32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.12 |
| aluRS232ReportAlarm The value of aluRS232ReportAlarm determines when and if to
generate aluEqPortRS232Alarm and aluEqPortRS232AlarmClear
notifications for this port:
hcmOof - Reports local HCM out-of… | column | AluRS232ReportStatus | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.13 |
| aluRS232ReportAlarmStatus The value of aluRS232ReportAlarmStatus indicates the alarms on
this port. | column | AluRS232ReportStatus | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.14 |
| aluRS232ControlLeadDtrDsr aluRS232ControlLeadDtrDsr is used to configure the DTR/DSR input lead
to an ASSUMED value.
For RS-232, V.35 and RS-530:
if local gender is DCE, lead indicates Data Terminal Read… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.15 |
| aluRS232ControlLeadRtsDcdC aluRS232ControlLeadRtsDcdC is used to configure the RTS/DCD/C input lead
to an ASSUMED value.
For RS-232, V.35 and RS-530:
if local gender is DCE, lead indicates Request To Send… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.16 |
| aluRS232ControlLeadAlbCts aluRS232ControlLeadAlbCts is used to configure the ALB/CTS input lead
to an ASSUMED value.
For RS-232 and V.35:
if local gender is DCE, lead indicates Analog loopback
if local… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.17 |
| aluRS232ControlLeadRdlRi aluRS232ControlLeadRdlRi is used to configure the RDL/RI input lead
to an ASSUMED value.
For RS-232:
if local gender is DCE, lead indicates Remote Digital Loopback
if local g… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.18 |
| aluRS232ControlLeadDsrDtr aluRS232ControlLeadDsrDtr is used to configure the DSR/DTR output lead
to a FORCED value.
For RS-232, V.35 and RS-530:
if local gender is DCE, lead indicates Data Set Ready
if… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.19 |
| aluRS232LastChangeTime aluRS232LastChangeTime contains the sysUpTime value of the
most recently modified writable variable in the
aluRS232Entry row for this Serial channel. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.2 |
| aluRS232ControlLeadDcdRtsI aluRS232ControlLeadDcdRtsI is used to configure the DCD/RTS/I output lead
to a FORCED value.
For RS-232, V.35 and RS-530:
if local gender is DCE, lead indicates Data Carrier Det… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.20 |
| aluRS232ControlLeadCtsAlb aluRS232ControlLeadCtsAlb is used to configure the CTS/ALB output lead
to a FORCED value.
For RS-232 and V.35:
if local gender is DCE, lead indicates Clear To Send
if local ge… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.21 |
| aluRS232ControlLeadRiRdl aluRS232ControlLeadRiRdl is used to configure the RI/RDL output lead
to a FORCED value.
For RS-232:
if local gender is DCE, lead indicates Ring Indicator
if local gender is DT… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.22 |
| aluRS232ControlLeadsState aluRS232ControlLeadsState is an array of byte values used to indicate
the current states of the input and output control leads. These state
values are historically known as scan a… | column | OctetString | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.23 |
| aluRS232MultiDrop aluRS232MultiDrop is used to configure the Multi-drop Data Bridge (MDDB)
mode of the interface.
'slave' and 'master' mode is valid for subrate (HCM) speeds only.
… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.24 |
| aluRS232SBitSignaling aluRS232SBitSignaling is used to configure the S-Bit signaling
mode of the interface.
This object is valid for subrate (HCM) speeds only.
'on' is not… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.25 |
| aluRS232DataPosition aluRS232DataPosition is used to configure the HCM data position.
This object is valid for subrate (HCM) speeds only.
'f0b6' is not allowed while aluR… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.26 |
| aluRS232HoldTimeUp The value of aluRS232HoldTimeUp is used to configure the
hold-timer for link up event dampening. This guards against
reporting excessive interface transitions. This is implement… | column | deci-seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.27 |
| aluRS232HoldTimeDown The value of aluRS232HoldTimeDown is used to configure the
hold-timer for link down event dampening. This guards against
reporting excessive interface transitions. This is imple… | column | deci-seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.28 |
| aluRS232ControlLeadsSignal aluRS232ControlLeadsSignal is an array of byte values used to indicate
the current signal levels of the input and output control leads
(connected to the attached CPE). These value… | column | OctetString | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.29 |
| aluRS232Type aluRS232Type configures the interface for RS-232, V.35, X.21 or
RS-530. | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.3 |
| aluRS232ControlLeadMonDtrDsr aluRS232ControlLeadMonDtrDsr is used to configure monitoring of the
input control lead signal, DtrDsr. While monitored, detected
transitions will trigger aluRS232ControlLeadsSigna… | column | AluRS232ControlLeadMon | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.30 |
| aluRS232ControlLeadMonRtsDcdC aluRS232ControlLeadMonRtsDcdC is used to configure monitoring of the
input control lead signal, RtsDcdC. While monitored, detected
transitions will trigger aluRS232ControlLeadsSig… | column | AluRS232ControlLeadMon | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.31 |
| aluRS232ControlLeadMonAlbCts aluRS232ControlLeadMonAlbCts is used to configure monitoring of the
input control lead signal, AlbCts. While monitored, detected
transitions will trigger aluRS232ControlLeadsSigna… | column | AluRS232ControlLeadMon | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.32 |
| aluRS232ControlLeadMonRdlRi aluRS232ControlLeadMonRdlRi is used to configure monitoring of the
input control lead signal, RdlRi. While monitored, detected
transitions will trigger aluRS232ControlLeadsSignalC… | column | AluRS232ControlLeadMon | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.33 |
| aluRS232ClockSyncState The value of aluRS232ClockSyncState indicates the current clock
synchronization state if aluRS232ClockSource is 'dcrSerial'.
unknown(0) - Unsupported or unkno… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.34 |
| aluRS232ClockMasterPortId The value of aluRS232ClockMasterPortId indicates the current clock
synchronization master port id if aluRS232ClockSource is
'dcrSerial'. | column | TIMETRA-TC-MIBTmnxPortID | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.35 |
| aluRS232InvertClock The value of aluRS232InvertClock specifies whether to invert the
clock edge that the interface samples for received data (if local
gender is DCE) or transmitted data (if local gen… | column | TIMETRA-TC-MIBTmnxEnabledDisabled | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.36 |
| aluRS232MonClockDeviationRaise The value of the object aluRS232MonClockDeviationRaise specifies the
amount of time to debounce clock deviation before asserting the port
fault condition, 'monClockDeviation'. Clo… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.37 |
| aluRS232MonClockDeviationClear The value of the object aluRS232MonClockDeviationClear specifies the
amount of time to debounce no clock deviation before de-asserting the
port fault condition, 'monClockDeviation… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.38 |
| aluRS232MonDataInactivityRaise The value of the object aluRS232MonDataInactivityRaise specifies the
amount of time to debounce data inactivity before asserting the port
fault condition, 'monDataInactivity'.
… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.39 |
| aluRS232DeviceMode aluRS232DeviceMode configures the interface for
synchronous or asynchronous operation.
Changing to asynchronous results in defaulting of
aluRS232CharacterLength, al… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.4 |
| aluRS232MonDataInactivityClear The value of the object aluRS232MonDataInactivityClear specifies the
amount of time to debounce data activity before de-asserting the
port fault condition, 'monDataInactivity'.
… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.40 |
| aluRS232DeviceGender aluRS232DeviceGender configures the gender offered by the
local interface.
dte is not valid while the sub-channel is aluRS232SocketEntry.
dte is not … | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.5 |
| aluRS232Speed aluRS232Speed specifies the link speed of the Serial interface.
A value of 'speed1200' sets the link to 1200bps. A value of 'speed64k'
sets the link to 64kbps.
Vali… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.7 |
| aluRS232ClockSource aluRS232ClockSource specifies the clock for transmitted data
on a serial port.
slave(1) - clock is derived from the system
external(2) - clock is provided by … | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.8 |
| aluRS232Loopback aluRS232Loopback is used to put the port into a loopback mode.
The value of tmnxPortAdminStatus should be set to outOfService
in order for the loopback to be enabled.
… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.9 |