aluRS232ClockSource
ALU-PORT-MIB ·
.1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.8
Object
column
r/w
Enumeration
aluRS232ClockSource specifies the clock for transmitted data
on a serial port.
slave(1) - clock is derived from the system
external(2) - clock is provided by the attached device
dcrSerial(3) - clock is recovered from the differential timestamp in
the RTP header but undirectional only, from attached
source DCE device to attached slave DTE device
aluRS232ClockSource is 'notApplicable' while aluRS232DeviceMode is
asynchronous. The value 'notApplicable' is set by the system.
'external' and 'dcrSerial' are not supported on the SAR-H and SAR-Hc
systems.
'external' and 'dcrSerial' are not supported on sdiv1 and sdiv2.
'external' and 'dcrSerial' are supported on rs232 and rs530 only.
'dcrSerial' is not allowed while aluRS232MultiDrop is not disabled.
Context
- MIB
- ALU-PORT-MIB
- OID
.1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- aluRS232Entry
- Table
- aluRS232Table
- Siblings
- 39
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | notApplicable |
1 | slave |
2 | external |
3 | dcrSerial |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| aluRS232RowStatus aluRS232RowStatus controls the creation and deletion of
row entries in the aluRS232Table.
For row creation, the manager has to first calculate the
tmnxPortPortID based on the TiM… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.1 |
| aluRS232CharacterLength The aluRS232CharacterLength specifies the character length.
Parameter is only valid while the port is configured for asynchronous operation.
The value of aluRS232Ch… | column | Integer32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.10 |
| aluRS232Parity The aluRS232Parity specifies the parity type.
Parameter is only valid while the port is configured for asynchronous operation.
The value of aluRS232CharacterLength … | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.11 |
| aluRS232StopBits The aluRS232StopBits specifies the stop bits.
Parameter is only valid while the port is configured for asynchronous operation.
The value of aluRS232CharacterLength … | column | Integer32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.12 |
| aluRS232ReportAlarm The value of aluRS232ReportAlarm determines when and if to
generate aluEqPortRS232Alarm and aluEqPortRS232AlarmClear
notifications for this port:
hcmOof - Reports local HCM out-of… | column | AluRS232ReportStatus | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.13 |
| aluRS232ReportAlarmStatus The value of aluRS232ReportAlarmStatus indicates the alarms on
this port. | column | AluRS232ReportStatus | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.14 |
| aluRS232ControlLeadDtrDsr aluRS232ControlLeadDtrDsr is used to configure the DTR/DSR input lead
to an ASSUMED value.
For RS-232, V.35 and RS-530:
if local gender is DCE, lead indicates Data Terminal Read… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.15 |
| aluRS232ControlLeadRtsDcdC aluRS232ControlLeadRtsDcdC is used to configure the RTS/DCD/C input lead
to an ASSUMED value.
For RS-232, V.35 and RS-530:
if local gender is DCE, lead indicates Request To Send… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.16 |
| aluRS232ControlLeadAlbCts aluRS232ControlLeadAlbCts is used to configure the ALB/CTS input lead
to an ASSUMED value.
For RS-232 and V.35:
if local gender is DCE, lead indicates Analog loopback
if local… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.17 |
| aluRS232ControlLeadRdlRi aluRS232ControlLeadRdlRi is used to configure the RDL/RI input lead
to an ASSUMED value.
For RS-232:
if local gender is DCE, lead indicates Remote Digital Loopback
if local g… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.18 |
| aluRS232ControlLeadDsrDtr aluRS232ControlLeadDsrDtr is used to configure the DSR/DTR output lead
to a FORCED value.
For RS-232, V.35 and RS-530:
if local gender is DCE, lead indicates Data Set Ready
if… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.19 |
| aluRS232LastChangeTime aluRS232LastChangeTime contains the sysUpTime value of the
most recently modified writable variable in the
aluRS232Entry row for this Serial channel. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.2 |
| aluRS232ControlLeadDcdRtsI aluRS232ControlLeadDcdRtsI is used to configure the DCD/RTS/I output lead
to a FORCED value.
For RS-232, V.35 and RS-530:
if local gender is DCE, lead indicates Data Carrier Det… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.20 |
| aluRS232ControlLeadCtsAlb aluRS232ControlLeadCtsAlb is used to configure the CTS/ALB output lead
to a FORCED value.
For RS-232 and V.35:
if local gender is DCE, lead indicates Clear To Send
if local ge… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.21 |
| aluRS232ControlLeadRiRdl aluRS232ControlLeadRiRdl is used to configure the RI/RDL output lead
to a FORCED value.
For RS-232:
if local gender is DCE, lead indicates Ring Indicator
if local gender is DT… | column | AluRS232ControlLead | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.22 |
| aluRS232ControlLeadsState aluRS232ControlLeadsState is an array of byte values used to indicate
the current states of the input and output control leads. These state
values are historically known as scan a… | column | OctetString | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.23 |
| aluRS232MultiDrop aluRS232MultiDrop is used to configure the Multi-drop Data Bridge (MDDB)
mode of the interface.
'slave' and 'master' mode is valid for subrate (HCM) speeds only.
… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.24 |
| aluRS232SBitSignaling aluRS232SBitSignaling is used to configure the S-Bit signaling
mode of the interface.
This object is valid for subrate (HCM) speeds only.
'on' is not… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.25 |
| aluRS232DataPosition aluRS232DataPosition is used to configure the HCM data position.
This object is valid for subrate (HCM) speeds only.
'f0b6' is not allowed while aluR… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.26 |
| aluRS232HoldTimeUp The value of aluRS232HoldTimeUp is used to configure the
hold-timer for link up event dampening. This guards against
reporting excessive interface transitions. This is implement… | column | deci-seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.27 |
| aluRS232HoldTimeDown The value of aluRS232HoldTimeDown is used to configure the
hold-timer for link down event dampening. This guards against
reporting excessive interface transitions. This is imple… | column | deci-seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.28 |
| aluRS232ControlLeadsSignal aluRS232ControlLeadsSignal is an array of byte values used to indicate
the current signal levels of the input and output control leads
(connected to the attached CPE). These value… | column | OctetString | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.29 |
| aluRS232Type aluRS232Type configures the interface for RS-232, V.35, X.21 or
RS-530. | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.3 |
| aluRS232ControlLeadMonDtrDsr aluRS232ControlLeadMonDtrDsr is used to configure monitoring of the
input control lead signal, DtrDsr. While monitored, detected
transitions will trigger aluRS232ControlLeadsSigna… | column | AluRS232ControlLeadMon | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.30 |
| aluRS232ControlLeadMonRtsDcdC aluRS232ControlLeadMonRtsDcdC is used to configure monitoring of the
input control lead signal, RtsDcdC. While monitored, detected
transitions will trigger aluRS232ControlLeadsSig… | column | AluRS232ControlLeadMon | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.31 |
| aluRS232ControlLeadMonAlbCts aluRS232ControlLeadMonAlbCts is used to configure monitoring of the
input control lead signal, AlbCts. While monitored, detected
transitions will trigger aluRS232ControlLeadsSigna… | column | AluRS232ControlLeadMon | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.32 |
| aluRS232ControlLeadMonRdlRi aluRS232ControlLeadMonRdlRi is used to configure monitoring of the
input control lead signal, RdlRi. While monitored, detected
transitions will trigger aluRS232ControlLeadsSignalC… | column | AluRS232ControlLeadMon | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.33 |
| aluRS232ClockSyncState The value of aluRS232ClockSyncState indicates the current clock
synchronization state if aluRS232ClockSource is 'dcrSerial'.
unknown(0) - Unsupported or unkno… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.34 |
| aluRS232ClockMasterPortId The value of aluRS232ClockMasterPortId indicates the current clock
synchronization master port id if aluRS232ClockSource is
'dcrSerial'. | column | TIMETRA-TC-MIBTmnxPortID | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.35 |
| aluRS232InvertClock The value of aluRS232InvertClock specifies whether to invert the
clock edge that the interface samples for received data (if local
gender is DCE) or transmitted data (if local gen… | column | TIMETRA-TC-MIBTmnxEnabledDisabled | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.36 |
| aluRS232MonClockDeviationRaise The value of the object aluRS232MonClockDeviationRaise specifies the
amount of time to debounce clock deviation before asserting the port
fault condition, 'monClockDeviation'. Clo… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.37 |
| aluRS232MonClockDeviationClear The value of the object aluRS232MonClockDeviationClear specifies the
amount of time to debounce no clock deviation before de-asserting the
port fault condition, 'monClockDeviation… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.38 |
| aluRS232MonDataInactivityRaise The value of the object aluRS232MonDataInactivityRaise specifies the
amount of time to debounce data inactivity before asserting the port
fault condition, 'monDataInactivity'.
… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.39 |
| aluRS232DeviceMode aluRS232DeviceMode configures the interface for
synchronous or asynchronous operation.
Changing to asynchronous results in defaulting of
aluRS232CharacterLength, al… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.4 |
| aluRS232MonDataInactivityClear The value of the object aluRS232MonDataInactivityClear specifies the
amount of time to debounce data activity before de-asserting the
port fault condition, 'monDataInactivity'.
… | column | seconds Unsigned32 | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.40 |
| aluRS232DeviceGender aluRS232DeviceGender configures the gender offered by the
local interface.
dte is not valid while the sub-channel is aluRS232SocketEntry.
dte is not … | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.5 |
| aluRS232Duplex aluRS232Duplex configures the duplex method of the interface to
half or full duplex.
full is not allowed while aluRS232MultiDrop is slave.
half is no… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.6 |
| aluRS232Speed aluRS232Speed specifies the link speed of the Serial interface.
A value of 'speed1200' sets the link to 1200bps. A value of 'speed64k'
sets the link to 64kbps.
Vali… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.7 |
| aluRS232Loopback aluRS232Loopback is used to put the port into a loopback mode.
The value of tmnxPortAdminStatus should be set to outOfService
in order for the loopback to be enabled.
… | column | Enumeration | .1.3.6.1.4.1.6527.6.1.2.2.2.4.5.1.9 |