TOKENRING-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view

Tables

Rows

Columns

dot5Table

table

.1.3.6.1.2.1.10.9.1 · 1 row entry · 10 columns

Open in standard view

This table contains Token Ring interface
parameters and state variables, one entry
per 802.5 interface.

dot5Entry entry .1.3.6.1.2.1.10.9.1.1

A list of Token Ring status and parameter
values for an 802.5 interface.

Indexes

dot5IfIndex

Column Syntax OID

dot5IfIndex

The value of this object identifies the
802.5 interface for which this entry
contains management information. The
value of this object for a particular
interface has the same value as the
ifIndex object, defined in MIB…

SNMPv2-SMIInteger32

Textual Convention: SNMPv2-SMIInteger32 Integer32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.2.1.10.9.1.1.1

dot5Commands

When this object is set to the value of
open(2), the station should go into the
open state. The progress and success of
the open is given by the values of the
objects dot5RingState and
dot5RingOpenStatus.
When this…

Enumerationr/w

Enumerated Values:

1	noop
2	open
3	reset
4	close

.1.3.6.1.2.1.10.9.1.1.2

dot5RingStatus

The current interface status which can
be used to diagnose fluctuating problems
that can occur on token rings, after a
station has successfully been added to
the ring.
Before an open is completed, this
object has the…

Integer32

Constraints:
range: 0-262143

.1.3.6.1.2.1.10.9.1.1.3

dot5RingState

The current interface state with respect
to entering or leaving the ring.

Enumeration

Enumerated Values:

1	opened
2	closed
3	opening
4	closing
5	openFailure
6	ringFailure

.1.3.6.1.2.1.10.9.1.1.4

dot5RingOpenStatus

This object indicates the success, or the
reason for failure, of the station's most
recent attempt to enter the ring.

Enumeration

Enumerated Values:

1	noOpen
2	badParam
3	lobeFailed
4	signalLoss
5	insertionTimeout
6	ringFailed
7	beaconing
8	duplicateMAC
9	requestFailed
10	removeReceived
11	open

.1.3.6.1.2.1.10.9.1.1.5

dot5RingSpeed

The ring-speed at the next insertion into
the ring. Note that this may or may not be
different to the current ring-speed which is
given by MIB-II's ifSpeed. For interfaces
which do not support changing ring-speed,
dot…

Enumerationr/w

Enumerated Values:

1	unknown
2	oneMegabit
3	fourMegabit
4	sixteenMegabit

.1.3.6.1.2.1.10.9.1.1.6

dot5UpStream

The MAC-address of the up stream neighbor
station in the ring.

SNMPv2-TCMacAddress

Textual Convention: SNMPv2-TCMacAddress OctetString

Type Constraints:
range: 6

.1.3.6.1.2.1.10.9.1.1.7

dot5ActMonParticipate

If this object has a value of true(1) then
this interface will participate in the
active monitor selection process. If the
value is false(2) then it will not.
Setting this object does not take effect
until the next Act…

Enumerationr/w

Enumerated Values:

1	true
2	false

.1.3.6.1.2.1.10.9.1.1.8

dot5Functional

The bit mask of all Token Ring functional
addresses for which this interface will
accept frames.

SNMPv2-TCMacAddressr/w

Textual Convention: SNMPv2-TCMacAddress OctetString

Type Constraints:
range: 6

.1.3.6.1.2.1.10.9.1.1.9

dot5LastBeaconSent

The value of MIB-II's sysUpTime object at which
the local system last transmitted a Beacon frame
on this interface.

SNMPv2-TCTimeStamp

Textual Convention: SNMPv2-TCTimeStamp Unsigned32

.1.3.6.1.2.1.10.9.1.1.10

dot5StatsTable

table

.1.3.6.1.2.1.10.9.2 · 1 row entry · 19 columns

Open in standard view

A table containing Token Ring statistics,
one entry per 802.5 interface.
    All the statistics are defined using
the syntax Counter32 as 32-bit wrap around
counters.  Thus, if an interface's
hardware maintains these statistics in
16-bit counters, then the agent must read
the hardware's counters frequently enough
to prevent loss of significance, in order
to maintain 32-bit counters in software.

dot5StatsEntry entry .1.3.6.1.2.1.10.9.2.1

An entry contains the 802.5 statistics
for a particular interface.

Indexes

dot5StatsIfIndex

Column	Syntax	OID
dot5StatsIfIndex The value of this object identifies the 802.5 interface for which this entry contains management information. The value of this object for a particular interface has the same value as MIB-II's ifIndex object for the sa…	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.2.1.1`
dot5StatsLineErrors This counter is incremented when a frame or token is copied or repeated by a station, the E bit is zero in the frame or token and one of the following conditions exists: 1) there is a non-data bit (J or K bit) between t…	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.2`
dot5StatsBurstErrors This counter is incremented when a station detects the absence of transitions for five half-bit timers (burst-five error).	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.3`
dot5StatsACErrors This counter is incremented when a station receives an AMP or SMP frame in which A is equal to C is equal to 0, and then receives another SMP frame with A is equal to C is equal to 0 without first receiving an AMP frame…	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.4`
dot5StatsAbortTransErrors This counter is incremented when a station transmits an abort delimiter while transmitting.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.5`
dot5StatsInternalErrors This counter is incremented when a station recognizes an internal error.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.6`
dot5StatsLostFrameErrors This counter is incremented when a station is transmitting and its TRR timer expires. This condition denotes a condition where a transmitting station in strip mode does not receive the trailer of the frame before the TR…	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.7`
dot5StatsReceiveCongestions This counter is incremented when a station recognizes a frame addressed to its specific address, but has no available buffer space indicating that the station is congested.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.8`
dot5StatsFrameCopiedErrors This counter is incremented when a station recognizes a frame addressed to its specific address and detects that the FS field A bits are set to 1 indicating a possible line hit or duplicate address.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.9`
dot5StatsTokenErrors This counter is incremented when a station acting as the active monitor recognizes an error condition that needs a token transmitted.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.10`
dot5StatsSoftErrors The number of Soft Errors the interface has detected. It directly corresponds to the number of Report Error MAC frames that this interface has transmitted. Soft Errors are those which are recoverable by the MAC layer pr…	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.11`
dot5StatsHardErrors The number of times this interface has detected an immediately recoverable fatal error. It denotes the number of times this interface is either transmitting or receiving beacon MAC frames.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.12`
dot5StatsSignalLoss The number of times this interface has detected the loss of signal condition from the ring.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.13`
dot5StatsTransmitBeacons The number of times this interface has transmitted a beacon frame.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.14`
dot5StatsRecoverys The number of Claim Token MAC frames received or transmitted after the interface has received a Ring Purge MAC frame. This counter signifies the number of times the ring has been purged and is being recovered back into…	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.15`
dot5StatsLobeWires The number of times the interface has detected an open or short circuit in the lobe data path. The adapter will be closed and dot5RingState will signify this condition.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.16`
dot5StatsRemoves The number of times the interface has received a Remove Ring Station MAC frame request. When this frame is received the interface will enter the close state and dot5RingState will signify this condition.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.17`
dot5StatsSingles The number of times the interface has sensed that it is the only station on the ring. This will happen if the interface is the first one up on a ring, or if there is a hardware problem.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.18`
dot5StatsFreqErrors The number of times the interface has detected that the frequency of the incoming signal differs from the expected frequency by more than that specified by the IEEE 802.5 standard.	SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.2.1.10.9.2.1.19`

dot5TimerTable

table obsolete

.1.3.6.1.2.1.10.9.5 · 1 row entry · 11 columns

Open in standard view

This table contains Token Ring interface
timer values, one entry per 802.5
interface.

dot5TimerEntry entry .1.3.6.1.2.1.10.9.5.1

A list of Token Ring timer values for an
802.5 interface.

Indexes

dot5TimerIfIndex

Column	Syntax	OID
dot5TimerIfIndex obsolete The value of this object identifies the 802.5 interface for which this entry contains timer values. The value of this object for a particular interface has the same value as MIB-II's ifIndex object for t…	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.1`
dot5TimerReturnRepeat obsolete The time-out value used to ensure the interface will return to Repeat State, in units of 100 micro-seconds. The value should be greater than the maximum ring latency.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.2`
dot5TimerHolding obsolete Maximum period of time a station is permitted to transmit frames after capturing a token, in units of 100 micro-seconds.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.3`
dot5TimerQueuePDU obsolete The time-out value for enqueuing of an SMP PDU after reception of an AMP or SMP frame in which the A and C bits were equal to 0, in units of 100 micro-seconds.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.4`
dot5TimerValidTransmit obsolete The time-out value used by the active monitor to detect the absence of valid transmissions, in units of 100 micro-seconds.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.5`
dot5TimerNoToken obsolete The time-out value used to recover from various-related error situations. If N is the maximum number of stations on the ring, the value of this timer is normally: dot5TimerReturnRepeat + N*dot5TimerHolding.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.6`
dot5TimerActiveMon obsolete The time-out value used by the active monitor to stimulate the enqueuing of an AMP PDU for transmission, in units of 100 micro-seconds.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.7`
dot5TimerStandbyMon obsolete The time-out value used by the stand-by monitors to ensure that there is an active monitor on the ring and to detect a continuous stream of tokens, in units of 100 micro-seconds.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.8`
dot5TimerErrorReport obsolete The time-out value which determines how often a station shall send a Report Error MAC frame to report its error counters, in units of 100 micro-seconds.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.9`
dot5TimerBeaconTransmit obsolete The time-out value which determines how long a station shall remain in the state of transmitting Beacon frames before entering the Bypass state, in units of 100 micro-seconds.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.10`
dot5TimerBeaconReceive obsolete The time-out value which determines how long a station shall receive Beacon frames from its downstream neighbor before entering the Bypass state, in units of 100 micro-seconds.	SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.2.1.10.9.5.1.11`