dot5TimerErrorReport
TOKENRING-MIB ·
.1.3.6.1.2.1.10.9.5.1.9
Object
The time-out value which determines how often a station shall send a Report Error MAC frame to report its error counters, in units of 100 micro-seconds.
Context
- MIB
- TOKENRING-MIB
- OID
.1.3.6.1.2.1.10.9.5.1.9- Type
- column
- Access
- readonly
- Status
- obsolete
- Parent
- dot5TimerEntry
- Table
- dot5TimerTable
- Siblings
- 10
Syntax
SNMPv2-SMIInteger32
- Source
- SNMPv2-SMIInteger32
- Base type
Integer32
Values & Constraints
Type Constraints
range: -2147483648..2147483647
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dot5TimerIfIndex obsolete The value of this object identifies the
802.5 interface for which this entry
contains timer values. The value of
this object for a particular interface
has the sam… | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.1 |
| dot5TimerBeaconTransmit obsolete The time-out value which determines how
long a station shall remain in the state
of transmitting Beacon frames before
entering the Bypass state, in units of
100 micro-seconds. | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.10 |
| dot5TimerBeaconReceive obsolete The time-out value which determines how
long a station shall receive Beacon
frames from its downstream neighbor
before entering the Bypass state, in
units of 100 micro-seconds. | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.11 |
| dot5TimerReturnRepeat obsolete The time-out value used to ensure the
interface will return to Repeat State, in
units of 100 micro-seconds. The value
should be greater than the maximum ring
latency. | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.2 |
| dot5TimerHolding obsolete Maximum period of time a station is
permitted to transmit frames after capturing
a token, in units of 100 micro-seconds. | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.3 |
| dot5TimerQueuePDU obsolete The time-out value for enqueuing of an SMP
PDU after reception of an AMP or SMP
frame in which the A and C bits were
equal to 0, in units of 100
micro-seconds. | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.4 |
| dot5TimerValidTransmit obsolete The time-out value used by the active
monitor to detect the absence of valid
transmissions, in units of 100
micro-seconds. | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.5 |
| dot5TimerNoToken obsolete The time-out value used to recover from
various-related error situations.
If N is the maximum number of stations on
the ring, the value of this timer is
normally:
dot5TimerReturnR… | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.6 |
| dot5TimerActiveMon obsolete The time-out value used by the active
monitor to stimulate the enqueuing of an
AMP PDU for transmission, in units of
100 micro-seconds. | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.7 |
| dot5TimerStandbyMon obsolete The time-out value used by the stand-by
monitors to ensure that there is an active
monitor on the ring and to detect a
continuous stream of tokens, in units of
100 micro-seconds. | column | SNMPv2-SMIInteger32 | .1.3.6.1.2.1.10.9.5.1.8 |