dot5TimerIfIndex

TOKENRING-MIB · .1.3.6.1.2.1.10.9.5.1.1
MIB view Table view

Object

column obsolete SNMPv2-SMIInteger32 
The value of this object identifies the
802.5 interface for which this entry
contains timer values.  The value of
              
this object for a particular interface
has the same value as MIB-II's ifIndex
object for the same interface.

Context

MIB
TOKENRING-MIB
OID
.1.3.6.1.2.1.10.9.5.1.1
Type
column
Access
readonly
Status
obsolete
Parent
dot5TimerEntry
Table
dot5TimerTable
Siblings
10

Syntax

SNMPv2-SMIInteger32
Source
SNMPv2-SMIInteger32
Base type
Integer32

Values & Constraints

Type Constraints
range: -2147483648..2147483647

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
dot5TimerBeaconTransmit obsolete
The time-out value which determines how long a station shall remain in the state of transmitting Beacon frames before entering the Bypass state, in units of 100 micro-seconds.
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.10
dot5TimerBeaconReceive obsolete
The time-out value which determines how long a station shall receive Beacon frames from its downstream neighbor before entering the Bypass state, in units of 100 micro-seconds.
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.11
dot5TimerReturnRepeat obsolete
The time-out value used to ensure the interface will return to Repeat State, in units of 100 micro-seconds. The value should be greater than the maximum ring latency.
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.2
dot5TimerHolding obsolete
Maximum period of time a station is permitted to transmit frames after capturing a token, in units of 100 micro-seconds.
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.3
dot5TimerQueuePDU obsolete
The time-out value for enqueuing of an SMP PDU after reception of an AMP or SMP frame in which the A and C bits were equal to 0, in units of 100 micro-seconds.
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.4
dot5TimerValidTransmit obsolete
The time-out value used by the active monitor to detect the absence of valid transmissions, in units of 100 micro-seconds.
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.5
dot5TimerNoToken obsolete
The time-out value used to recover from various-related error situations. If N is the maximum number of stations on the ring, the value of this timer is normally: dot5TimerReturnR…
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.6
dot5TimerActiveMon obsolete
The time-out value used by the active monitor to stimulate the enqueuing of an AMP PDU for transmission, in units of 100 micro-seconds.
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.7
dot5TimerStandbyMon obsolete
The time-out value used by the stand-by monitors to ensure that there is an active monitor on the ring and to detect a continuous stream of tokens, in units of 100 micro-seconds.
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.8
dot5TimerErrorReport obsolete
The time-out value which determines how often a station shall send a Report Error MAC frame to report its error counters, in units of 100 micro-seconds.
columnSNMPv2-SMIInteger32.1.3.6.1.2.1.10.9.5.1.9