G6-MSP1000-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
18
Rows
18
Columns
225
systemConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.1
·
1 row entry
·
5 columns
Indexes
systemConfigIndex
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
systemConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-0 |
.1.3.6.1.4.1.3181.10.6.1.94.1.1.1 |
||||
|
systemConfigNmsOperationMode
Read and learn in PASSIVE mode or ACTIVE mode forcing configuration upon the other modules.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.1.1.2 |
||||
|
systemConfigCoreMode
Use V2 unless used with an older system running in V1 mode. Only change when instructed.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.1.1.3 |
||||
|
systemConfigNodeId
Node Id used when NMS is used in combination with SEEmiles V5 management software. When in doubt use default node id 60000.
|
SNMPv2-SMIUnsigned32r/w Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.1.1.4 |
||||
|
systemConfigDisableLegacyAccess
When set network access via SEEmiles is no longer possible.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.1.1.5 |
slotConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.2
·
1 row entry
·
7 columns
Indexes
slotConfigIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
slotConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.2.1.1 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
slotConfigModule
Defines which module is expected to be placed in this slot. This should be identical to the actual hardware. The value may be set prior to actual roll-out to preconfigure the system.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.2.1.2 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
slotConfigSparepartMode
When enabled the module is operating normally but will not generate any alarms. This is useful for modules that are inserted but only used as spare and are not properly connected at this time. This way unnecassary alarm…
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.2.1.3 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
slotConfigPort1Alias
User defined port name for easier reference.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.2.1.4 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
slotConfigPort2Alias
User defined port name for easier reference.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.2.1.5 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
slotConfigPort3Alias
User defined port name for easier reference.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.2.1.6 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
slotConfigPort4Alias
User defined port name for easier reference.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.2.1.7 |
x2gConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.3
·
1 row entry
·
20 columns
This table is used to define any X2G or OFX-3 modules in the system.
Indexes
x2gConfigIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
x2gConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.3.1.1 |
||||||||||||||||||||||||||||||
|
x2gConfigPort1Datarate
This parameter defines the data rate used to setup the internal retimer to provide 3R regeneration. Note that internally interconnected ports must be set to the same rate.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.2 |
||||||||||||||||||||||||||||||
|
x2gConfigPort2Datarate
This parameter defines the data rate used to setup the internal retimer to provide 3R regeneration. Note that internally interconnected ports must be set to the same rate.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.3 |
||||||||||||||||||||||||||||||
|
x2gConfigPort3Datarate
This parameter defines the data rate used to setup the internal retimer to provide 3R regeneration. Note that internally interconnected ports must be set to the same rate.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.4 |
||||||||||||||||||||||||||||||
|
x2gConfigPort4Datarate
This parameter defines the data rate used to setup the internal retimer to provide 3R regeneration. Note that internally interconnected ports must be set to the same rate.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.5 |
||||||||||||||||||||||||||||||
|
x2gConfigCrossConnect
This parameter defines the data path through the module. It is also used to setup a permanent bit error rate test.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.6 |
||||||||||||||||||||||||||||||
|
x2gConfigDeactivatePort1
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.7 |
||||||||||||||||||||||||||||||
|
x2gConfigDeactivatePort2
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.8 |
||||||||||||||||||||||||||||||
|
x2gConfigDeactivatePort3
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.9 |
||||||||||||||||||||||||||||||
|
x2gConfigDeactivatePort4
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.10 |
||||||||||||||||||||||||||||||
|
x2gConfigFrontPanelMode
Determines what is displayed on the front panel, when available. Also controls the modules local buttons.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.11 |
||||||||||||||||||||||||||||||
|
x2gConfigLossOfSignalHandling
When set to LOCAL a loss of input signal will not affect another port. When set to PERCOLATE, a loss of signal will turn off the transmitter of the currently associated port.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.12 |
||||||||||||||||||||||||||||||
|
x2gConfigOptimizedFor8b10b
Enable this feature when Ethernet or FibreChannel is used. Do not set when SDH is used on any port.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.13 |
||||||||||||||||||||||||||||||
|
x2gConfigBertPattern
Defines the bit pattern with which the build-in bit error rate tester (BERT) operates when cross connect is set to BERT.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.14 |
||||||||||||||||||||||||||||||
|
x2gConfigSfpDeltaInterval
This enables and defines the interval in which the optical receive power level of each SFP is read and compared to previous value.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.15 |
||||||||||||||||||||||||||||||
|
x2gConfigSfpDeltaThreshold
This defines how much the optical receive power level can differ between successive reads before a warning trap is generated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.16 |
||||||||||||||||||||||||||||||
|
x2gConfigBackupTrigger
Defines under which optical signal condition an automated backup is initiated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.17 |
||||||||||||||||||||||||||||||
|
x2gConfigStayWithLastLink
When set the backup switch remains in last position even when signal returns. Still the backup warning turns off after the delay set under backup_end parameter expires.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.18 |
||||||||||||||||||||||||||||||
|
x2gConfigBackupEnd
Defines how long the signal must remain steady before proper operation is assumed and the backup is terminated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.19 |
||||||||||||||||||||||||||||||
|
x2gConfigPermitLinkOverride
Permits the manual selection of a failed link using the link selection. Defaults to false to safeguard against accidential link selection which would result in loss of connection.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.3.1.20 |
txgConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.4
·
1 row entry
·
12 columns
This table is used to define any TXG or XCM-2 modules in the system.
Indexes
txgConfigIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
txgConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.4.1.1 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigTxgDatarate
This parameter defines the data rate used to setup the internal retimer to provide 3R regeneration. Note that internally interconnected ports must be set to the same rate.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.2 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigTxgOperationMode
This parameter defines the data path through the module when an internal cross connect is avalable. It is also used to setup a permanent bit error rate test. (most settings apply to X2G, TXG, OFX-3, XCM-2 only)
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.3 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigPort1ItuChannel
Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.4 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigPort2ItuChannel
Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.5 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigDeactivatePort1
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.6 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigDeactivatePort2
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.7 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigFrontPanelMode
Determines what is displayed on the front panel, when available. Also controls the modules local buttons.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.8 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigLossOfSignalHandling
When set to LOCAL a loss of input signal will not affect another port. When set to PERCOLATE, a loss of signal will turn off the transmitter of the other port.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.9 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigBertPattern
Defines the bit pattern with which the build-in bit error rate tester (BERT) operates when cross connect is set to BERT.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.10 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigSfpDeltaInterval
This enables and defines the interval in which the optical receive power level of each SFP/XFP is read and compared to previous value.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.11 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
txgConfigSfpDeltaThreshold
This defines how much the optical receive power level can differ between successive reads before a warning trap is generated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.4.1.12 |
cxgPlusConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.5
·
1 row entry
·
15 columns
This table is used to define any CXG+ or OFC-10 modules in the system.
Indexes
cxgPlusConfigIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
cxgPlusConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.5.1.1 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigCxgPort12Datarate
The CXG relies on the features of the XFP to define its datarate. Since various XFP offer different rates with the same settings, only a general setting is provided. Both ports must operate at the same rate.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.2 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigCxgPort34Datarate
The CXG relies on the features of the XFP to define its datarate. Since various XFP offer different rates with the same settings, only a general setting is provided. Both ports must operate at the same rate.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.3 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigPort1ItuChannel
Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.4 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigPort2ItuChannel
Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.5 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigPort3ItuChannel
Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.6 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigPort4ItuChannel
Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.7 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigDeactivatePort1
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.8 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigDeactivatePort2
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.9 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigDeactivatePort3
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.10 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigDeactivatePort4
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.11 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigFrontPanelMode
Determines what is displayed on the front panel, when available. Also controls the modules local buttons.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.12 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigLossOfSignalHandling
When set to LOCAL a loss of input signal will not affect another port. When set to PERCOLATE, a loss of signal will turn off the transmitter of the other port.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.13 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigSfpDeltaInterval
This enables and defines the interval in which the optical receive power level of each SFP/XFP is read and compared to previous value.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.14 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgPlusConfigSfpDeltaThreshold
This defines how much the optical receive power level can differ between successive reads before a warning trap is generated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.5.1.15 |
cxgConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.6
·
1 row entry
·
10 columns
This table is used to define any CXG or XCM-3 modules in the system.
Indexes
cxgConfigIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
cxgConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.6.1.1 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgConfigCxgPort12Datarate
The CXG relies on the features of the XFP to define its datarate. Since various XFP offer different rates with the same settings, only a general setting is provided. Both ports must operate at the same rate.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.6.1.2 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgConfigPort1ItuChannel
Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.6.1.3 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgConfigPort2ItuChannel
Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.6.1.4 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgConfigDeactivatePort1
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.6.1.5 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgConfigDeactivatePort2
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.6.1.6 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgConfigFrontPanelMode
Determines what is displayed on the front panel, when available. Also controls the modules local buttons.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.6.1.7 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgConfigLossOfSignalHandling
When set to LOCAL a loss of input signal will not affect another port. When set to PERCOLATE, a loss of signal will turn off the transmitter of the other port.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.6.1.8 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgConfigSfpDeltaInterval
This enables and defines the interval in which the optical receive power level of each SFP/XFP is read and compared to previous value.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.6.1.9 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
cxgConfigSfpDeltaThreshold
This defines how much the optical receive power level can differ between successive reads before a warning trap is generated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.6.1.10 |
t4gConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.7
·
1 row entry
·
13 columns
This table is used to define any T4G or OFC-4 modules in the system.
Indexes
t4gConfigIndex
| Column | Syntax | OID | ||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
t4gConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.7.1.1 |
||||||||||||||||||||||
|
t4gConfigT4gPort12Datarate
The CXG relies on the features of the XFP to define its datarate. Since various XFP offer different rates with the same settings, only a general setting is provided. Both ports must operate at the same rate.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.2 |
||||||||||||||||||||||
|
t4gConfigT4gPort34Datarate
Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.3 |
||||||||||||||||||||||
|
t4gConfigT4gOperationMode
This parameter defines the data path through the module when an internal cross connect is avalable. It is also used to setup a permanent bit error rate test. (most settings apply to X2G, TXG, OFX-3, XCM-2 only)
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.4 |
||||||||||||||||||||||
|
t4gConfigDeactivatePort1
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.5 |
||||||||||||||||||||||
|
t4gConfigDeactivatePort2
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.6 |
||||||||||||||||||||||
|
t4gConfigDeactivatePort3
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.7 |
||||||||||||||||||||||
|
t4gConfigDeactivatePort4
When enabled, the optical interface is disabled and communication is cut.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.8 |
||||||||||||||||||||||
|
t4gConfigFrontPanelMode
Determines what is displayed on the front panel, when available. Also controls the modules local buttons.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.9 |
||||||||||||||||||||||
|
t4gConfigLossOfSignalHandling
When set to LOCAL a loss of input signal will not affect another port. When set to PERCOLATE, a loss of signal will turn off the transmitter of the other port.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.10 |
||||||||||||||||||||||
|
t4gConfigBertPattern
Defines the bit pattern with which the build-in bit error rate tester (BERT) operates when cross connect is set to BERT.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.11 |
||||||||||||||||||||||
|
t4gConfigSfpDeltaInterval
This enables and defines the interval in which the optical receive power level of each SFP/XFP is read and compared to previous value.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.12 |
||||||||||||||||||||||
|
t4gConfigSfpDeltaThreshold
This defines how much the optical receive power level can differ between successive reads before a warning trap is generated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.7.1.13 |
m2gConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.8
·
1 row entry
·
11 columns
This table is used to define any M2G or TDM-2 modules in the system.
Indexes
m2gConfigIndex
| Column | Syntax | OID | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
m2gConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.8.1.1 |
||||||||||||||
|
m2gConfigChannel1Datarate
Devices the datarate of the first TDM channel (port 1)
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.2 |
||||||||||||||
|
m2gConfigChannel2Datarate
Devices the datarate of the second TDM channel (port 2)
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.3 |
||||||||||||||
|
m2gConfigPort1CopperSfp
Set when local copper RJ45 SFP is used and connection cannot be established.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.4 |
||||||||||||||
|
m2gConfigPort2CopperSfp
Set when local copper RJ45 SFP is used and connection cannot be established.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.5 |
||||||||||||||
|
m2gConfigSfpDeltaInterval
This enables and defines the interval in which the optical receive power level of each SFP/XFP is read and compared to previous value.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.6 |
||||||||||||||
|
m2gConfigSfpDeltaThreshold
This defines how much the optical receive power level can differ between successive reads before a warning trap is generated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.7 |
||||||||||||||
|
m2gConfigLinkBackupTrigger
Defines under which optical signal condition an automated backup is initiated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.8 |
||||||||||||||
|
m2gConfigStayWithLastLink
When set the backup switch remains in last position even when signal returns. Still the backup warning turns off after the delay set under backup_end parameter expires.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.9 |
||||||||||||||
|
m2gConfigBackupEnd
Defines how long the signal must remain steady before proper operation is assumed and the backup is terminated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.10 |
||||||||||||||
|
m2gConfigPermitLinkOverride
Permits the manual selection of a failed link using the link selection. Defaults to false to safeguard against accidential link selection which would result in loss of connection.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.8.1.11 |
om1ConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.9
·
1 row entry
·
8 columns
Indexes
om1ConfigIndex
| Column | Syntax | OID | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
om1ConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.9.1.1 |
||||||||||
|
om1ConfigWavelengthPortA
Defines which wavelength band is measured. Use 1550 setting when a WDM link is measured.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.9.1.2 |
||||||||||
|
om1ConfigLowThresholdPortA
Defines the lower optical signal level in dBm. A signal level below this threshold will trigger an event.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.9.1.3 |
||||||||||
|
om1ConfigHighThresholdPortA
Defines the upper optical signal level in dBm. A signal level above this threshold will trigger an event.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.9.1.4 |
||||||||||
|
om1ConfigWavelengthPortB
Defines which wavelength band is measured. Use 1550 setting when a WDM link is measured.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.9.1.5 |
||||||||||
|
om1ConfigLowThresholdPortB
Defines the lower optical signal level in dBm. A signal level below this threshold will trigger an event.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.9.1.6 |
||||||||||
|
om1ConfigHighThresholdPortB
Defines the upper optical signal level in dBm. A signal level above this threshold will trigger an event.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.9.1.7 |
||||||||||
|
om1ConfigFrontPanelMode
Determines what is displayed on the front panel, when available. Also controls the modules local buttons.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.9.1.8 |
lp1ConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.10
·
1 row entry
·
11 columns
Indexes
lp1ConfigIndex
| Column | Syntax | OID | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
lp1ConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.10.1.1 |
||||||||||
|
lp1ConfigWavelengthPortA
Defines which wavelength band is measured. Use 1550 setting when a WDM link is measured.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.10.1.2 |
||||||||||
|
lp1ConfigLowThresholdPortA
Defines the lower optical signal level in dBm. A signal level below this threshold will trigger an event and a backup when configured.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.10.1.3 |
||||||||||
|
lp1ConfigHighThresholdPortA
Defines the upper optical signal level in dBm. A signal level above this threshold will trigger an event and a backup when configured.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.10.1.4 |
||||||||||
|
lp1ConfigWavelengthPortB
Defines which wavelength band is measured. Use 1550 setting when a WDM link is measured.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.10.1.5 |
||||||||||
|
lp1ConfigLowThresholdPortB
Defines the lower optical signal level in dBm. A signal level below this threshold will trigger an event and a backup when configured.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.10.1.6 |
||||||||||
|
lp1ConfigHighThresholdPortB
Defines the upper optical signal level in dBm. A signal level above this threshold will trigger an event and a backup when configured.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.10.1.7 |
||||||||||
|
lp1ConfigBackupCriteria
Defines under which optical signal condition an automated backup is initiated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.10.1.8 |
||||||||||
|
lp1ConfigStayWithLastLink
When set the backup switch remains in last position even when signal return. Still the backup warning turns off after the delay set under backup_end parameter expires.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.10.1.9 |
||||||||||
|
lp1ConfigBackupEnd
Defines how long the signal must remain steady before proper operation is assumed and the backup is terminated.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.10.1.10 |
||||||||||
|
lp1ConfigFrontPanelMode
Determines what is displayed on the front panel, when available. Also controls the modules local buttons.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.10.1.11 |
emConfigTable
table.1.3.6.1.4.1.3181.10.6.1.94.11
·
1 row entry
·
10 columns
Configuration for EDFA amplifier modules EM2 and EM3.
Indexes
emConfigIndex
| Column | Syntax | OID | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
emConfigIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.11.1.1 |
||||||||||
|
emConfigEdfaOperationMode
Defines which wavelength band is measured. Use 1550 setting when a WDM link is measured.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.11.1.2 |
||||||||||
|
emConfigLossOfSignalHandling
Defines if loss of input signal turns off the EDFA pump (PERCOLATE) or not (LOCAL)
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.11.1.3 |
||||||||||
|
emConfigSignalGain
Desired signal gain in dB.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.11.1.4 |
||||||||||
|
emConfigMaxOutputPower
Maximum output power permitted to exit the module.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.11.1.5 |
||||||||||
|
emConfigLowThresholdEdfaIn
This corresponds to the unamplified input signal before entering the EDFA section. Defines the lower optical signal level in dBm. A signal level below this threshold will trigger an event.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.11.1.6 |
||||||||||
|
emConfigHighThresholdEdfaIn
This corresponds to the unamplified input signal before entering the EDFA section. Defines the upper optical signal level in dBm. A signal level above this threshold will trigger an event.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.11.1.7 |
||||||||||
|
emConfigLowThresholdPortB
Port B is the unamplified return path through the module. Defines the lower optical signal level in dBm. A signal level below this threshold will trigger an event.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.11.1.8 |
||||||||||
|
emConfigHighThresholdPortB
Port B is the unamplified return path through the module. Defines the upper optical signal level in dBm. A signal level above this threshold will trigger an event.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.11.1.9 |
||||||||||
|
emConfigFrontPanelMode
Determines what is displayed on the front panel, when available. Also controls the modules local buttons.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.11.1.10 |
moduleControlTable
table.1.3.6.1.4.1.3181.10.6.1.94.12
·
1 row entry
·
18 columns
Indexes
moduleControlIndex
| Column | Syntax | OID |
|---|---|---|
|
moduleControlIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.1 |
|
moduleControlEnterPassword
This command will set the module password. Only required when the nms_operation_mode is set to passive mode. Enter the password before configuration or actions can be accepted by the module.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.2 |
|
moduleControlRebootModule
This command will restart the module. All communication will be disrupted! Syntax: reboot_module = CONFIRM.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.3 |
|
moduleControlWarmStart
This command will warm start the module. Communication shall not be disrupted. (Firmware dependend) Syntax: warm_start = CONFIRM.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.4 |
|
moduleControlClearCounter
This command will clear all module and port related statistics counter.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.5 |
|
moduleControlSwitchOffBackup
For a module that supports backup and which currently is in backup condition this command will revert to normal operation. If this would disrupt traffic a warning is returned and nothing is executed. To override this wa…
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.6 |
|
moduleControlSwitchToBackup
For a module that supports backup this command will switch to the backup link. If this would disrupt traffic because backup link is not available a warning is returned and nothing is executed. To override this warning a…
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.7 |
|
moduleControlAutomaticBackup
This command returns a manually overridden backup module to normal automatic mode. No parameter are required.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.8 |
|
moduleControlWriteDisplay
Writes to the front panel display of the module. Only for modules that offer a front panel display.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.9 |
|
moduleControlLedTest
This will start the modules LED test and will return the LED back up automatic mode after a few seconds. May be also be used to identify a certain module.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.10 |
|
moduleControlLoopOff
Turns all loops off
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.11 |
|
moduleControlLoopPort1
Tries to engage a loop at port 1. Note not all modules support loops. View port status to check success.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.12 |
|
moduleControlLoopPort2
Tries to engage a loop at port 2. Note not all modules support loops. View port status to check success.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.13 |
|
moduleControlLoopPort3
Tries to engage a loop at port 3. Note not all modules support loops. View port status to check success.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.14 |
|
moduleControlLoopPort4
Tries to engage a loop at port 4. Note not all modules support loops. View port status to check success.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.15 |
|
moduleControlBertRestart
Resynchronizes BERT. Only has an effect if a BERT is available on the module and configured to be active.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.16 |
|
moduleControlBertInsertError
Inserts an error in the data pattern. This can be used to confirm that a BERT is actually operating. Only has an effect if a BERT is available on the module and configured to be active.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.17 |
|
moduleControlBertClearCounter
Clears the BERT counter. Only has an effect if a BERT is available on the module and configured to be active.
|
SNMPv2-TCDisplayStringr/w Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.12.1.18 |
systemStatusTable
table.1.3.6.1.4.1.3181.10.6.1.94.100
·
1 row entry
·
7 columns
Indexes
systemStatusIndex
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
systemStatusIndex
Automatically generated
|
Integer32 Constraints: range: 0-0 |
.1.3.6.1.4.1.3181.10.6.1.94.100.1.1 |
||||
|
systemStatusAnyErrorCondition
True when any error condition is currently present in any module.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.100.1.2 |
||||
|
systemStatusAnyTestMode
True when any module is in loopback test or has a backup engaged.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.100.1.3 |
||||
|
systemStatusAnySparePart
True when any module is marked as spare part.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.100.1.4 |
||||
|
systemStatusUsedNodeId
Actually used node id as discovered from device
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.100.1.5 |
||||
|
systemStatusLocalRack
Indicates in which rack the mangement module over which this information is retrieved is inserted.
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.100.1.6 |
||||
|
systemStatusLocalSlot
Indicates in which slot the mangement module over which this information is retrieved is inserted.
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.100.1.7 |
moduleInventoryTable
table.1.3.6.1.4.1.3181.10.6.1.94.101
·
1 row entry
·
19 columns
Indexes
moduleInventoryIndex
| Column | Syntax | OID | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
moduleInventoryIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.1 |
||||||||||||||||
|
moduleInventoryExpectedModule
Name of module configured for this slot.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.2 |
||||||||||||||||
|
moduleInventoryModule
Name of module actually discovered in this slot. This name should be equal to the above name otherwise configuration may not apply properly.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.3 |
||||||||||||||||
|
moduleInventoryType
General functional type of module inserted.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.101.1.4 |
||||||||||||||||
|
moduleInventoryBoardCode
Internal code of actually inserted module.
|
Integer32 Constraints: range: 0-255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.5 |
||||||||||||||||
|
moduleInventoryAdditionalInfo
Additional information that may be saved in some modules during production.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.6 |
||||||||||||||||
|
moduleInventorySerialNumber
Serial number as stored within the hardware.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.7 |
||||||||||||||||
|
moduleInventoryOccupiedSlots
Number of slots taken by this module. Usually 1.
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.8 |
||||||||||||||||
|
moduleInventoryProjectNumber
Internal hardware project number
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.9 |
||||||||||||||||
|
moduleInventoryBuildVersion
Precise build code for hardware version tracking.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.10 |
||||||||||||||||
|
moduleInventoryProductionDate
Production data of the module
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.11 |
||||||||||||||||
|
moduleInventoryMfgTestInfo
Internal information for quality management. Manufacturing Site / Test Site / Test Person
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.12 |
||||||||||||||||
|
moduleInventoryNumberOfOpticalPorts
Indicates the number of actively monitored optical ports of this type of module.
|
Integer32 Constraints: range: 0-255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.13 |
||||||||||||||||
|
moduleInventoryNumberOfSfpPorts
Indicates the number of optical SFP or SFP+ ports of this type of module.
|
Integer32 Constraints: range: 0-255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.14 |
||||||||||||||||
|
moduleInventoryNumberOfXfpPorts
Indicates the number of optical XFP ports of this type of module.
|
Integer32 Constraints: range: 0-255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.15 |
||||||||||||||||
|
moduleInventoryCoreFirmwareVersion
Core operating system software version.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.16 |
||||||||||||||||
|
moduleInventoryCoreFirmwareDate
Core operating system software creation date.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.17 |
||||||||||||||||
|
moduleInventoryApplFirmwareVersion
Application software version.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.18 |
||||||||||||||||
|
moduleInventoryApplFirmwareDate
Application software creation date.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.101.1.19 |
moduleStatusTable
table.1.3.6.1.4.1.3181.10.6.1.94.102
·
1 row entry
·
13 columns
This table holds a record for each module in the system. Note that not all modules deliver every kind of status.
Indexes
moduleStatusIndex
| Column | Syntax | OID | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
moduleStatusIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.102.1.1 |
||||||||
|
moduleStatusModule
Name of module actually discovered in this slot.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.102.1.2 |
||||||||
|
moduleStatusSystemOk
True when the module has booted and appears ok.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.102.1.3 |
||||||||
|
moduleStatusErrorCondition
True when any error condition is currently present.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.102.1.4 |
||||||||
|
moduleStatusTestMode
True when module is in loopback test or a backup is engaged.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.102.1.5 |
||||||||
|
moduleStatusSparePart
True when module is marked as spare part.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.102.1.6 |
||||||||
|
moduleStatusUptime
Uptime since last reboot in seconds.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.102.1.7 |
||||||||
|
moduleStatusTimeSinceCounterReset
How long ago have the statistics counter been restarted.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.102.1.8 |
||||||||
|
moduleStatusTemperature
Temperature value in centigrade.
|
Integer32 Constraints: range: 0-255 |
.1.3.6.1.4.1.3181.10.6.1.94.102.1.9 |
||||||||
|
moduleStatusTooHot
True when module is running too hot.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.102.1.10 |
||||||||
|
moduleStatusBackupState
Indicates if a backup is active and in which state.
|
Bits Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.102.1.11 |
||||||||
|
moduleStatusBackupCounter
Counts the number of times this module has initiated a backup (if backup feature is available for this module type).
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.102.1.12 |
||||||||
|
moduleStatusBackupDuration
How long the backup has been activated in total since last value reset.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.102.1.13 |
portStatusTable
table.1.3.6.1.4.1.3181.10.6.1.94.103
·
1 row entry
·
19 columns
This table holds a record for each optical port of the system. Note that not all modules deliver every kind of statistic.
Indexes
portStatusPortIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
portStatusPortIndex
Automatically generated
|
Integer32 Constraints: range: 0-47 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.1 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusModule
Name of module in which this port is present.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.2 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusLocation
Textual description of port location.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.3 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusSnmpPort
Slot and port representation as used in SNMP. Formula is Slot*10000 + Port*10.
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.4 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusAlias
Configured alias nickname of this port.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.5 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusAdminStatus
Reflects the administrative setting of this port.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.103.1.6 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusOperStatus
Indicates the combined operation port status.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.103.1.7 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusDetailedStatus
Indicates detailed issues related to the port.
|
Bits Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.103.1.8 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusPortDatarate
Reflects the data rate setting of this port.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.103.1.9 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusUpdateTimeStamp
Indicates the time when this record was last updated.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.10 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusTimeSinceValueReset
Time since when the following statistics have been accumulated. They restart upon module power up or on forced value reset.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.11 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusTimeSinceLastError
Time since last input signal loss or input signal too high.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.12 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusTimeSignalTooLow
Total time the input signal was below threshold.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.13 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusSignalTooLowCounter
Number of times a transition to signal too low has occured.
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.14 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusTimeSignalTooHigh
Total time the input signal was above high threshold.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.15 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusSignalTooHighCounter
Number of times a transition to signal too high has occured.
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.16 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusLowThreshold
Defined signal too low threshold.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.17 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusCurrentInputSignal
Actual current signal level.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.18 |
||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
portStatusHighThreshold
Defined signal too high threshold.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.103.1.19 |
emStatusTable
table.1.3.6.1.4.1.3181.10.6.1.94.104
·
1 row entry
·
16 columns
Optical amplifier status
Indexes
emStatusIndex
| Column | Syntax | OID | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
emStatusIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.1 |
||||||||||||||||
|
emStatusSystemOk
True when no errors are present
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.104.1.2 |
||||||||||||||||
|
emStatusErrors
Indicates various optical error conditions.
|
Bits Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.104.1.3 |
||||||||||||||||
|
emStatusHardwareCode
Details codes about the installed hardware components.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.4 |
||||||||||||||||
|
emStatusTimeSincePowerError
How long ago since the last time the output power was in error condition.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.5 |
||||||||||||||||
|
emStatusTimeWithPowerLoss
Accumulated time the output power has been down.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.6 |
||||||||||||||||
|
emStatusInputSignalLowCounter
Number of times a loss of signal has occured.
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.7 |
||||||||||||||||
|
emStatusInputPower
Optical input power of port A.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.8 |
||||||||||||||||
|
emStatusSignalGain
Indicates how strong the input signal is amplified.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.9 |
||||||||||||||||
|
emStatusOptimalFlatGain
Indicates the best gain setting for an even amplification accross the wavelength channels
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.10 |
||||||||||||||||
|
emStatusBackReflection
The value should be low and indicates cable issues if not.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.11 |
||||||||||||||||
|
emStatusSignalOutputPower
Indicated the actually achieved optical signal output power.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.12 |
||||||||||||||||
|
emStatusTotalOutputPower
Indicated the actually achieved optical output power leaving the module (including noise).
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.13 |
||||||||||||||||
|
emStatusMinOutputPower
Indicates the minimum optical output level that must be send out
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.14 |
||||||||||||||||
|
emStatusMaxOutputPower
Indicates the maximum optical output level that can be send out
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.15 |
||||||||||||||||
|
emStatusCfgOutputPower
Indicated the desired configured optical output power
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.104.1.16 |
bertStatusTable
table.1.3.6.1.4.1.3181.10.6.1.94.105
·
1 row entry
·
11 columns
Displays the results of the bit error rate tester (BERT) if it is present and enabled in a slot
Indexes
bertStatusIndex
| Column | Syntax | OID | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
bertStatusIndex
Automatically generated
|
Integer32 Constraints: range: 0-11 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.1 |
||||||||
|
bertStatusLocation
Textual description of BERT port location.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.2 |
||||||||
|
bertStatusBertOperation
Indicates the general bit error rate tester operational status.
|
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.3181.10.6.1.94.105.1.3 |
||||||||
|
bertStatusTotalErrors
Number of errored bits. Only valid when BERT is synchronized.
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.4 |
||||||||
|
bertStatusTimeSinceLastError
Seconds elapsed since the last error was detected.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.5 |
||||||||
|
bertStatusTotalTestTime
Accumulated time how long the test was run since last value clear.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.6 |
||||||||
|
bertStatusErroredTime
Accumulated seconds in which at least on errored bit was detected.
|
SNMPv2-SMICounter32 Textual Convention: SNMPv2-SMICounter32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.7 |
||||||||
|
bertStatusBitErrorRate
Averaged bit error rate during test interval.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.8 |
||||||||
|
bertStatusBerSinceLastError
Bit error rate since last error.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.9 |
||||||||
|
bertStatusTheoreticalBer
Theoretical best possible error rate in the given time frame of the current test interval.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.10 |
||||||||
|
bertStatusAvailability
Relation of transmitted vs. Errored bits.
|
SNMPv2-TCDisplayString Textual Convention: SNMPv2-TCDisplayString OctetStringType Constraints: range: 0..255 |
.1.3.6.1.4.1.3181.10.6.1.94.105.1.11 |