txgConfigTxgOperationMode
G6-MSP1000-MIB ·
.1.3.6.1.4.1.3181.10.6.1.94.4.1.3
Object
column
r/w
Enumeration
This parameter defines the data path through the module when an internal cross connect is avalable. It is also used to setup a permanent bit error rate test. (most settings apply to X2G, TXG, OFX-3, XCM-2 only)
Context
- MIB
- G6-MSP1000-MIB
- OID
.1.3.6.1.4.1.3181.10.6.1.94.4.1.3- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- txgConfigEntry
- Table
- txgConfigTable
- Siblings
- 11
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | disabled |
2 | transponder |
3 | repeater |
4 | bertPort1 |
5 | bertPort2 |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| txgConfigIndex Automatically generated | column | Integer32 | .1.3.6.1.4.1.3181.10.6.1.94.4.1.1 |
| txgConfigBertPattern Defines the bit pattern with which the build-in bit error rate tester (BERT) operates when cross connect is set to BERT. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.10 |
| txgConfigSfpDeltaInterval This enables and defines the interval in which the optical receive power level of each SFP/XFP is read and compared to previous value. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.11 |
| txgConfigSfpDeltaThreshold This defines how much the optical receive power level can differ between successive reads before a warning trap is generated. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.12 |
| txgConfigTxgDatarate This parameter defines the data rate used to setup the internal retimer to provide 3R regeneration. Note that internally interconnected ports must be set to the same rate. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.2 |
| txgConfigPort1ItuChannel Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.4 |
| txgConfigPort2ItuChannel Tunable laser are supported. Select the wavelength from the supplied 100GHZ ITU-T grid. If the wavelength is not supported by the XFP, a warning event will be received. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.5 |
| txgConfigDeactivatePort1 When enabled, the optical interface is disabled and communication is cut. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.6 |
| txgConfigDeactivatePort2 When enabled, the optical interface is disabled and communication is cut. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.7 |
| txgConfigFrontPanelMode Determines what is displayed on the front panel, when available. Also controls the modules local buttons. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.8 |
| txgConfigLossOfSignalHandling When set to LOCAL a loss of input signal will not affect another port. When set to PERCOLATE, a loss of signal will turn off the transmitter of the other port. | column | Enumeration | .1.3.6.1.4.1.3181.10.6.1.94.4.1.9 |