CISCO-WIRELESS-P2MP-PHY-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
10
Rows
10
Columns
61

p2mpRadioPhyTable

table
.1.3.6.1.4.1.9.9.170.1.1.1.1 · 1 row entry · 9 columns
Open in standard view 
This table provides facilities to configure the physical
layer characteristics of the radio link.
The objects in this table are supported on the head end and 
at the subscriber unit.
p2mpRadioPhyEntry entry .1.3.6.1.4.1.9.9.170.1.1.1.1.1
The entry of this table is created when the managed system
detects a propDocsWirelessMaclayer interface. The entry
is removed when the associated propDocsWirelessMaclayer
interface is deleted from the ifTable.
Indexes
IF-MIBifIndex
Column Syntax OID
p2mpSelfTest
This object is used to enable/disable self test. When set to
true(1), the software tests the memory and hardware integrity
shortly after the router powers up.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.1
p2mpDiversityAntennaPresent
When true(1), this object indicates that a diversity
antenna is being used to receive the wireless transmissions.
When false(2), the radio system is using a single antenna
to transmit and receive.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.2
p2mpCableLoss
This object indicates the measured signal power loss in dB
due to the cable connecting the radio to the main antenna.
The hardware compensates for this cable loss by adjusting the
receive and transmit gain appropriately…
dBUnsigned32r/w
Constraints:
range: 0-15
 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.3
p2mpCableLossDiversity
This object indicates the measured signal power loss in dB
due to the cable connecting the radio to the diversity
antenna. The hardware compensates for this loss by adjusting
the receive and transmit gain appropriat…
dBUnsigned32r/w
Constraints:
range: 0-15
 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.4
p2mpDenyService
Indicates if the service is disabled in the unit.
For Head-end unit, if this object has the value of
'true', the link is in loopback mode; otherwise the
link is enabled for transmitting / receiving data.
For Subscribe…
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.5
p2mpClockRefExt
This object controls the use of external reference
clock for IF module as follows:
'true(1)' - an external reference clock is used
'false(2)' - an internal reference clock is used.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.6
p2mpCommonTrapEnable
When set to true(1), the notifications common to the head end
and subscriber unit are enabled. When set to false(2), these
notifications are disabled.
The notification controlled by this object are:
- p2mpRadioPhy…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.7
p2mpLastPhyFailureType
This object indicates the last physical link failure that
resulted in a p2mpRadioPhyFailNotification trap.

none(1) - no failure

p2mpHwConfigUnsupported(2) - The radio subsystem has…
Enumeration
Enumerated Values:
1none
2p2mpHwConfigUnsupported
3p2mpHwConfigMismatch
4p2mpHwInitFailure
5p2mpHostIfCommLinkError
6p2mpAutoCableCompFailure
 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.8
p2mpLastPhyFailureReason
This is a text string that describes the last physical link
failure identified by p2mpLastPhyFailureType.
OctetString
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.170.1.1.1.1.1.9

p2mpRfTable

table
.1.3.6.1.4.1.9.9.170.1.1.2.1 · 1 row entry · 15 columns
Open in standard view 
This table contains information about the state of the radio 
frequency resources used by the radio system.
          
Physically each RF resource may be realized by one antenna and 
its associated control hardware. A single antenna and its 
associated electronics may act as more than 1 RF resource. When
an RF resource acts as both a transmit and receive resource,
the transmit and receive frequency ranges may overlap.
p2mpRfEntry entry .1.3.6.1.4.1.9.9.170.1.1.2.1.1
This represents one entry in the p2mpRfTable.

An entry is created in this table when the managed system
detects a RF resource. The entry is removed when the RF
resource is removed from the wireless syst…
Indexes
IF-MIBifIndex p2mpRfIndex
Column Syntax OID
p2mpRfIndex
This object, along with the ifIndex of the MAC layer,
represents the index of this entry in the p2mpRfTable.
Each entry in the table provides details on the state of
the RF resources available in the system.
Integer32
Constraints:
range: 1-100
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.1
p2mpRfType
This object identifies the RF resource.
CISCO-WIRELESS-TC-MIBCwrRfType
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfType Enumeration
Type Values:
0main
1diversity
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.2
p2mpRfOpMode
This object specifies whether this RF resource can either
transmit, receive, or do both.
Enumeration
Enumerated Values:
1receiveOnly
2transmitOnly
3transmitAndReceive
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.3
p2mpTxFreqRangeMin
This object represents the minimum frequency at which this RF
resource can transmit.
KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfFreqRange Integer32
Type Constraints:
range: 0..60000000
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.4
p2mpTxFreqRangeMax
This object represents the maximum frequency at which this RF
resource can transmit.
KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfFreqRange Integer32
Type Constraints:
range: 0..60000000
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.5
p2mpRxFreqRangeMin
This object represents the lowest transmission frequency this
RF resource can receive.
KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfFreqRange Integer32
Type Constraints:
range: 0..60000000
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.6
p2mpRxFreqRangeMax
This object represents the highest transmission frequency that
this RF resource can receive.
KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfFreqRange Integer32
Type Constraints:
range: 0..60000000
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.7
p2mpMinTxPower
This object represents the minimum power that the RF subsystem
can supply the antenna.
dBmInteger32
Constraints:
range: -80-50
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.8
p2mpMaxTxPower
This object represents the maximum power that the RF subsystem
can supply the antenna.
dBmInteger32
Constraints:
range: -80-50
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.9
p2mpRfTemperature
This object represents the current temperature of the RF unit
Degrees CentigradeInteger32
Constraints:
range: -40-100
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.10
p2mpRfTxOscState
This object represents the state of the transmit oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
CISCO-WIRELESS-TC-MIBCwrOscState
Textual Convention: CISCO-WIRELESS-TC-MIBCwrOscState Enumeration
Type Values:
1oscillatorOk
2osccillatorBad
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.11
p2mpRfRxOscState
This object represents the state of the receive oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
CISCO-WIRELESS-TC-MIBCwrOscState
Textual Convention: CISCO-WIRELESS-TC-MIBCwrOscState Enumeration
Type Values:
1oscillatorOk
2osccillatorBad
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.12
p2mpRfSupplyVoltageState
This object specifies whether the voltage supply to the RF
unit is within specifications or not. Voltage specifications
are hardware dependent.
Enumeration
Enumerated Values:
1withinSpecification
2outsideSpecification
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.13
p2mpRfStatus
This object specifies whether the RF resource is functioning
properly. If it is functioning properly then it will be
online(1), else offline(2).
At the Subscriber Unit, this object will reflect offline(2)
if p2mpTxMu…
Enumeration
Enumerated Values:
1online
2offline
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.14
p2mpRfLoopbackSupported
This object indicates if the RF unit supports loopback.
When true(1), the user can configure loopback using the
objects in p2mpLoopbackTable. When false(2), any attempt
to configure RF loopback will fail.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.170.1.1.2.1.1.15

p2mpDuplexerTable

table
.1.3.6.1.4.1.9.9.170.1.1.2.2 · 1 row entry · 9 columns
Open in standard view 
This table contains information about the Duplexers
available for use on the system.
          
A Duplexer is a mechanical device, that acts as a band 
pass filter when installed in an RF resource.
          
Normally a RF resource is capable of operating over a wide
frequency range. To operate at restricted frequencies, the user
has to own that part of the frequency spectrum.  Since the user
may not own parts of the frequency spectrum over which the RF
resource may operate, a duplexer is installed at the RF.
This restricts the RF resource to operate in the passband
defined by the duplexer.
p2mpDuplexerEntry entry .1.3.6.1.4.1.9.9.170.1.1.2.2.1
This represents one entry in the p2mpDuplexerTable.
Each entry contains information about the duplexers
capabilities and the associated RF resource.

An entry is created in this table when the managed syst…
Indexes
IF-MIBifIndex p2mpDuplexerIndex
Column Syntax OID
p2mpDuplexerIndex
This object, along with ifIndex, uniquely identifies
an entry in this table. Each entry contains
information about the duplexer's capabilities and also
identifies the associated RF resource.
Integer32
Constraints:
range: 1-100
 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.1
p2mpDuplexerRF
This object identifies the RF resource associated with this
duplexer.
CISCO-WIRELESS-TC-MIBCwrRfType
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfType Enumeration
Type Values:
0main
1diversity
 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.2
p2mpDuplexerLoPassbandMinFreq
This object identifies the minimum frequency in the low
passband that this duplexer will pass through without
attenuation.
MHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfFreqRange Integer32
Type Constraints:
range: 0..60000000
 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.3
p2mpDuplexerLoPassbandMaxFreq
This object identifies the maximum frequency in the low
passband that this duplexer will pass through without
attenuation.
MHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfFreqRange Integer32
Type Constraints:
range: 0..60000000
 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.4
p2mpDuplexerHiPassbandMinFreq
This object identifies the minimum frequency in the high
passband that this duplexer will pass through without
attenuation.
MHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfFreqRange Integer32
Type Constraints:
range: 0..60000000
 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.5
p2mpDuplexerHiPassbandMaxFreq
This object identifies the maximum frequency in the high
passband that this duplexer will pass through without
attenuation.
MHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfFreqRange Integer32
Type Constraints:
range: 0..60000000
 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.6
p2mpDuplexerReceivePassband
This object indicates which of the two passbands are being used
to receive transmissions. The RF Resource can receive on
either of the duplexer passbands.

loPassband(1) - The RF Resource is receiving on …
Enumeration
Enumerated Values:
1loPassband
2hiPassband
 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.7
p2mpDuplexerTxInsertionLoss
This object represents the loss in 'dB' that would result in
the transmission path due to the duplexer.
dBSNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.8
p2mpDuplexerBurnDate
This object indicates the date when the revision information
was programmed into non-volatile memory.
SNMPv2-TCDisplayString
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.170.1.1.2.2.1.9

p2mpAntennaTable

table
.1.3.6.1.4.1.9.9.170.1.1.2.3 · 1 row entry · 8 columns
Open in standard view 
This table contains information about the antennas available 
in the system.
p2mpAntennaEntry entry .1.3.6.1.4.1.9.9.170.1.1.2.3.1
An entry is created in this table when the managed system
detects a RF resource. The entry is removed when the RF
resource is removed from the wireless system.
Indexes
IF-MIBifIndex p2mpAntennaIndex
Column Syntax OID
p2mpAntennaIndex
This object, along with ifIndex, represents the index of this
entry in the p2mpAntennaTable.
CISCO-TCUnsigned32
Textual Convention: CISCO-ATM-SWITCH-CUG-MIBUnsigned32 Unsigned32
 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.1
p2mpRfResource
This object identifies if the antenna is connected to the main
or the diversity RF resource.
CISCO-WIRELESS-TC-MIBCwrRfType
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfType Enumeration
Type Values:
0main
1diversity
 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.2
p2mpAntennaXDim
This object represents the dimension of the antenna in the
X direction.
InchesUnsigned32r/w
Constraints:
range: 1-96
 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.3
p2mpAntennaYDim
This object represents the dimension of the antenna in the
Y direction.
InchesUnsigned32r/w
Constraints:
range: 1-96
 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.4
p2mpAntennaType
This object represents the antenna type. For example,
'dish-antenna'.
OctetStringr/w
Constraints:
range: 0-64
 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.5
p2mpAntennaDescr
This object is used to describe the antenna. For example,
it could be used to identify the manufacturer like in
'Manufactured by Watkins Johnson'.
OctetStringr/w
Constraints:
range: 0-64
 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.6
p2mpAntennaGain
This object represents the receive and transmit gain
of this antenna.
dBi : decibel IsotropicUnsigned32r/w
Constraints:
range: 0-60
 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.7
p2mpAntennaPolarization
This object represents the polarization of the antanna.
Enumeration
Enumerated Values:
1vertical
2horizontal
 .1.3.6.1.4.1.9.9.170.1.1.2.3.1.8

p2mpLoopbackTable

table
.1.3.6.1.4.1.9.9.170.1.1.3.1 · 1 row entry · 3 columns
Open in standard view 
This table provides facilities to establish loopback points to
exercise various sections of the hardware.
p2mpLoopbackEntry entry .1.3.6.1.4.1.9.9.170.1.1.3.1.1
This represents one entry in the p2mpLoopbackTable. It
is created when the managed system detects a
propDocsWirelessMaclayer interface. The entry is removed
when the associated propDocsWirelessMaclayer interface
is d…
Indexes
IF-MIBifIndex
Column Syntax OID
p2mpLocalLoopbackMode
This object is used to configure the system in loopback mode
prior to executing some system diagnostic tests. The user
selects the point in the system where the data signal should be
looped back. The diagnostic test…
Enumerationr/w
Enumerated Values:
1noLoopback
2fir
3if
4rf
 .1.3.6.1.4.1.9.9.170.1.1.3.1.1.1
p2mpLocalLoopbackAntenna
This object identifies the RF resource used for
loopback testing. This object is not applicable for
loopback testing when p2mpLocalLoopbackMode has a
value of 'noLoopback(1)'.
CISCO-WIRELESS-TC-MIBCwrRfTyper/w
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfType Enumeration
Type Values:
0main
1diversity
 .1.3.6.1.4.1.9.9.170.1.1.3.1.1.2
p2mpLocalLoopbackChannel
This object identifies the channel being used to
loopback the data. This object is not applicable
for loopback testing when p2mpLocalLoopbackMode has
a value of 'noLoopback(1)'.
Unsigned32r/w
Constraints:
range: 1-7
 .1.3.6.1.4.1.9.9.170.1.1.3.1.1.3

p2mpLedTable

table
.1.3.6.1.4.1.9.9.170.1.1.4.1 · 1 row entry · 3 columns
Open in standard view 
Entity (Light emitting diode) LED information.  For each LED on
the entity, an entry will exist in this table, describing the
location and current status of that LED.
p2mpLedEntry entry .1.3.6.1.4.1.9.9.170.1.1.4.1.1
An entry in the table, containing the LED information.
The entPhysicalIndex identifies the entity on which the LED's
are present.
Indexes
ENTITY-MIBentPhysicalIndex p2mpLedIndex
Column Syntax OID
p2mpLedIndex
For a given entPhysicalIndex, this index value uniquely
identifies an entry in the p2mpLedTable.
Integer32
Constraints:
range: 1-16
 .1.3.6.1.4.1.9.9.170.1.1.4.1.1.1
p2mpLedType
Indicates the type or label of the LED.
Enumeration
Enumerated Values:
0interfaceEnable
1majorAlarm
2minorAlarm
3outOfService
4carrier
5transmitData
6receiveData
 .1.3.6.1.4.1.9.9.170.1.1.4.1.1.2
p2mpLedState
Indicates the state of the LED.
Enumeration
Enumerated Values:
0off
1green
2yellow
 .1.3.6.1.4.1.9.9.170.1.1.4.1.1.3

p2mpSuRadioPhyTable

table
.1.3.6.1.4.1.9.9.170.1.2.1 · 1 row entry · 2 columns
Open in standard view 
This table contains information about the currently configured
physical layer interfaces in the subscriber unit.
p2mpSuRadioPhyEntry entry .1.3.6.1.4.1.9.9.170.1.2.1.1
An entry containing the radio configuration information
of the propDocsWirelessMaclayer interface in the
subscriber unit.

The entry is created when a propDocsWirelessMaclayer
interface is detected in the s…
Indexes
IF-MIBifIndex
Column Syntax OID
p2mpSuTxMuteEnable
When true(1), this object indicates the subscriber unit
transmission has been turned off for a duration indicated by
p2mpSuTxMuteDuration. When false(2), this object indicates
that the subscriber unit is transmitting.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.170.1.2.1.1.1
p2mpSuTxMuteDuration
This object indicates the duration of time (in minutes)
for which the subscriber transmission will be turned off.
minutesUnsigned32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.9.9.170.1.2.1.1.2

p2mpSuPowerScanTable

table
.1.3.6.1.4.1.9.9.170.1.2.2 · 1 row entry · 3 columns
Open in standard view 
This table contains information about the receive power 
measured at the different possible center frequencies.
p2mpSuPowerScanEntry entry .1.3.6.1.4.1.9.9.170.1.2.2.1
An entry containing the power related status
information of the propDocsWirelessMaclayer
interface in the subscriber unit.

The entry is created when a propDocsWirelessMaclayer
interface is detected in th…
Indexes
IF-MIBifIndex p2mpSuPowerScanIndex
Column Syntax OID
p2mpSuPowerScanIndex
For a given ifIndex, this index value uniquely
identifies an entry in the p2mpSuPowerScanTable.
Integer32
Constraints:
range: 1-20
 .1.3.6.1.4.1.9.9.170.1.2.2.1.1
p2mpSuCenterFrequency
This object indicates the frequency at which the receive power
at the subscriber unit was measured.
KHzCISCO-WIRELESS-TC-MIBCwrRfFreqRange
Textual Convention: CISCO-WIRELESS-TC-MIBCwrRfFreqRange Integer32
Type Constraints:
range: 0..60000000
 .1.3.6.1.4.1.9.9.170.1.2.2.1.2
p2mpSuMeasuredPower
This object represents the power measured at the frequency
indicated by p2mpSuCenterFrequency.
dBmInteger32
Constraints:
range: -127-50
 .1.3.6.1.4.1.9.9.170.1.2.2.1.3

p2mpHeAlcTable

table
.1.3.6.1.4.1.9.9.170.1.3.1 · 1 row entry · 3 columns
Open in standard view 
This table contains Automatic Line Control (ALC) configuration 
information.  It is supported at the head end only.
p2mpHeAlcEntry entry .1.3.6.1.4.1.9.9.170.1.3.1.1
An entry containing the ALC configuration information
the propDocsWirelessMaylayer interface at the head end.

The entry is created when a propDocsWirelessMaclayer
interface is detected in the head end uni…
Indexes
IF-MIBifIndex
Column Syntax OID
p2mpHeAlcEnable
This object is used to enable/disable ALC at the Head End. A
value of true(1), indicates that ALC is enabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.170.1.3.1.1.1
p2mpHeAlcInterval
This object represents the scheduling interval. It is the
regular interval at which the ALC grant in Map is transmitted
to the SU's
millisecondsUnsigned32r/w
Constraints:
range: 32-1024
 .1.3.6.1.4.1.9.9.170.1.3.1.1.2
p2mpHeAlcNumMiniSlots
This indicates the number of minislots within each grant.
Unsigned32r/w
Constraints:
range: 1-4
 .1.3.6.1.4.1.9.9.170.1.3.1.1.3

p2mpHeIntFreqTable

table
.1.3.6.1.4.1.9.9.170.1.3.2 · 1 row entry · 6 columns
Open in standard view 
This table contains information about the state of the 
intermediate frequency subsystem in the radio system.  This
table is supported at the head end only.
p2mpHeIntFreqEntry entry .1.3.6.1.4.1.9.9.170.1.3.2.1
The entry of this table is created when the managed system
detects a propDocsWirelessMaclayer interface in the head
end unit.
The entry is deleted when the associated
propDocsWirelessMaclayer interface is removed.
Indexes
IF-MIBifIndex
Column Syntax OID
p2mpHeIfTxOscState
This object indicates the state of the IF transmit oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
CISCO-WIRELESS-TC-MIBCwrOscState
Textual Convention: CISCO-WIRELESS-TC-MIBCwrOscState Enumeration
Type Values:
1oscillatorOk
2osccillatorBad
 .1.3.6.1.4.1.9.9.170.1.3.2.1.1
p2mpHeIfRxOscState
This object indicates the state of the IF receive oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
CISCO-WIRELESS-TC-MIBCwrOscState
Textual Convention: CISCO-WIRELESS-TC-MIBCwrOscState Enumeration
Type Values:
1oscillatorOk
2osccillatorBad
 .1.3.6.1.4.1.9.9.170.1.3.2.1.2
p2mpHeIfRefOscState
This object indicates the state of the IF reference oscillator.
The oscillator must be in oscillatorOk(1) state for the system
to function properly.
CISCO-WIRELESS-TC-MIBCwrOscState
Textual Convention: CISCO-WIRELESS-TC-MIBCwrOscState Enumeration
Type Values:
1oscillatorOk
2osccillatorBad
 .1.3.6.1.4.1.9.9.170.1.3.2.1.3
p2mpHeIfInpFreq
This object represents the IF input frequency.
KHzUnsigned32
Constraints:
range: 1000-500000
 .1.3.6.1.4.1.9.9.170.1.3.2.1.4
p2mpHeIfOutFreq
This object represents the IF output frequency.
KHzUnsigned32
Constraints:
range: 1000-500000
 .1.3.6.1.4.1.9.9.170.1.3.2.1.5
p2mpHeTrapEnable
When set to true(1), this enables the notifications
that are specific to the head end. When set to false(2),
these notifications are disabled.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.170.1.3.2.1.6