p2mpLastPhyFailureType

CISCO-WIRELESS-P2MP-PHY-MIB · .1.3.6.1.4.1.9.9.170.1.1.1.1.1.8

Object

column Enumeration

This object indicates the last physical link failure that 
resulted in a p2mpRadioPhyFailNotification trap.
              
    none(1) - no failure
              
    p2mpHwConfigUnsupported(2) - The radio subsystem has 
       detected that the configuration requested is not 
       supported by the hardware.  The p2mpLastPhyFailureReason
       variable will indicate which configuration parameter is
       not supported.
              
    p2mpHwConfigMismatch(3) - The radio subsystem has detected 
       that the combination of the configuration parameters 
       requested is inconsistent and cannot be supported.
       The p2mpLastPhyFailReason variable will indicate the 
       configuration parameter that causes the mismatch.
              
    p2mpHwInitFailure(4) - The radio subsystem has failed to 
       initialize the hardware. This implies that there is a 
       critical error condition in the associated hardware. 
       The p2mpLastPhyFailReason specifies the reason why the 
       init failed.
              
    p2mpHostIfCommLinkError(5) - The host could not communicate 
       with the IF module.
              
    p2mpAutoCableCompFailure(6) - Failed to achieve automatic 
       cable compensation due to loss of Tx signal.

Context

MIB: CISCO-WIRELESS-P2MP-PHY-MIB
OID: .1.3.6.1.4.1.9.9.170.1.1.1.1.1.8
Type: column
Access: readonly
Status: current
Parent: p2mpRadioPhyEntry
Table: p2mpRadioPhyTable
Siblings: 8

Syntax

Enumeration

Values & Constraints

Enumerated Values

`1`	none
`2`	p2mpHwConfigUnsupported
`3`	p2mpHwConfigMismatch
`4`	p2mpHwInitFailure
`5`	p2mpHostIfCommLinkError
`6`	p2mpAutoCableCompFailure

Related Objects

Sibling Objects

Object	Type	Syntax	OID
p2mpSelfTest This object is used to enable/disable self test. When set to true(1), the software tests the memory and hardware integrity shortly after the router powers up.	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.170.1.1.1.1.1.1`
p2mpDiversityAntennaPresent When true(1), this object indicates that a diversity antenna is being used to receive the wireless transmissions. When false(2), the radio system is using a single antenna to tran…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.170.1.1.1.1.1.2`
p2mpCableLoss This object indicates the measured signal power loss in dB due to the cable connecting the radio to the main antenna. The hardware compensates for this cable loss by adjusting the…	column	dB Unsigned32	`.1.3.6.1.4.1.9.9.170.1.1.1.1.1.3`
p2mpCableLossDiversity This object indicates the measured signal power loss in dB due to the cable connecting the radio to the diversity antenna. The hardware compensates for this loss by adjusting …	column	dB Unsigned32	`.1.3.6.1.4.1.9.9.170.1.1.1.1.1.4`
p2mpDenyService Indicates if the service is disabled in the unit. For Head-end unit, if this object has the value of 'true', the link is in loopback mode; otherwise the link is enabled for tran…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.170.1.1.1.1.1.5`
p2mpClockRefExt This object controls the use of external reference clock for IF module as follows: 'true(1)' - an external reference clock is used 'false(2)' - an internal reference clock is us…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.170.1.1.1.1.1.6`
p2mpCommonTrapEnable When set to true(1), the notifications common to the head end and subscriber unit are enabled. When set to false(2), these notifications are disabled. The notification controll…	column	SNMPv2-TCTruthValue	`.1.3.6.1.4.1.9.9.170.1.1.1.1.1.7`
p2mpLastPhyFailureReason This is a text string that describes the last physical link failure identified by p2mpLastPhyFailureType.	column	OctetString	`.1.3.6.1.4.1.9.9.170.1.1.1.1.1.9`