CISCO-VOICE-ANALOG-IF-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
11
Rows
11
Columns
50

cvaIfCfgTable

table
.1.3.6.1.4.1.9.9.62.1.1.1 · 1 row entry · 2 columns
Open in standard view 
The Analog Voice Standard Configuration Table. It contains 
the standard configuration information of the analog          
telephony interface.
cvaIfCfgEntry entry .1.3.6.1.4.1.9.9.62.1.1.1.1
An entry in the configuration table for each voice analog
interface. The entry is created when the voice analog
hardware is detected.
Indexes
IF-MIBifIndex
Column Syntax OID
cvaIfCfgImpedance
Specifies the terminating impedance of voice analog
interfaces.
other - none of the following; arbitrary,
within limits, for special cases.
ohms600Real - 600 Ohms.
ohms600Complex - 600 Ohms …
Enumerationr/w
Enumerated Values:
1other
2ohms600Real
3ohms600Complex
4ohms900Complex
5ohmsComplex1
6ohmsComplex2
 .1.3.6.1.4.1.9.9.62.1.1.1.1.1
cvaIfCfgIntegratedDSP
Indicates whether the interface has an integrated
Digital Signal processing (DSP) unit.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.1.1.1.2

cvaIfStatusTable

table
.1.3.6.1.4.1.9.9.62.1.1.2 · 1 row entry · 3 columns
Open in standard view 
The Analog Voice Status Table.  It contains general 
information about the status of Analog Telephony interface
including the error statistics.
cvaIfStatusEntry entry .1.3.6.1.4.1.9.9.62.1.1.2.1
An entry in the status table for each Analog voice interface.
Indexes
No indexes recorded
Column Syntax OID
cvaIfStatusInfoType
The information transfer services for the current
or last call.
none - no information transfer service
voice - analog voice.
g3Fax - Group 3 FAX.
Enumeration
Enumerated Values:
1none
2voice
3g3Fax
 .1.3.6.1.4.1.9.9.62.1.1.2.1.1
cvaIfMaintenanceMode
Indicates the maintenance modes of the Analog voice interface.

Managed system
+=============+=============================+
| Voice | +===========+ telephony |
<=====+ application +===+ CODEC …
Enumeration
Enumerated Values:
1none
2hostCompressedLoopback
3hostUncompressedLoopback
4ifCompressedLoopback
5ifUncompressedLoopback
 .1.3.6.1.4.1.9.9.62.1.1.2.1.2
cvaIfStatusSignalErrors
Accumulated number of signaling protocol errors that are
detected in the interface since system startup.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.62.1.1.2.1.3

cvaIfEMCfgTable

table
.1.3.6.1.4.1.9.9.62.1.2.1 · 1 row entry · 7 columns
Open in standard view 
The E&M standard configuration table. It contains 
the current setting of E&M configurable parameters.
cvaIfEMCfgEntry entry .1.3.6.1.4.1.9.9.62.1.2.1.1
An entry in the standard configuration table for
each E&M tie trunk interface.
Indexes
IF-MIBifIndex
Column Syntax OID
cvaIfEMCfgSignalType
The signaling type of E&M tie trunk interface.
winkStart - the calling side seizes the line by going
off-hook on its E lead but waits for a short
off-hook 'wink' indication on its M lead from
…
Enumerationr/w
Enumerated Values:
1winkStart
2immediateDial
3delayDial
4lmr
5fgd
6fgd-eana
 .1.3.6.1.4.1.9.9.62.1.2.1.1.1
cvaIfEMCfgOperation
Specify the operation of the E&M signal.
twoWires - 2-wire operation.
fourWires - 4-wire operation.
Enumerationr/w
Enumerated Values:
1twoWires
2fourWires
 .1.3.6.1.4.1.9.9.62.1.2.1.1.2
cvaIfEMCfgType
Specifies the E&M Lead Signaling type.
LEGEND: V = -48V
/\/\/ = detector/resister
X = normally open relay contact
+ = normally closed relay contact
G = ground
SB = Signal Battery
SG = Signal Ground…
Enumerationr/w
Enumerated Values:
1typeI
2typeII
3typeIII
4typeIV
5typeV
 .1.3.6.1.4.1.9.9.62.1.2.1.1.3
cvaIfEMCfgDialType
Specifies the out dialing type of E&M interface.
InterfaceDialTyper/w
Textual Convention: InterfaceDialType Enumeration
Type Values:
1dtmf
2pulse
3mf
 .1.3.6.1.4.1.9.9.62.1.2.1.1.4
cvaIfEMCfgLmrMCap
The M lead behavior of E&M LMR interface.
inact - The m-lead status should be ignored.
audio - The m-lead status is used to control
generating voice packet.
dial - Perform the same audio case except abling to
…
Enumerationr/w
Enumerated Values:
1inact
2audio
3dial
 .1.3.6.1.4.1.9.9.62.1.2.1.1.5
cvaIfEMCfgLmrECap
The E lead behavior of E&M LMR interface.
seize - The e-lead used as seize signal
voice - The e-lead status is used to indicate
voice packet received or not.
inactive -- e-lead is inactive.
Enumerationr/w
Enumerated Values:
4seize
5voice
6inactive
 .1.3.6.1.4.1.9.9.62.1.2.1.1.6
cvaIfEMCfgAutoGainControl
This object is used to enabling/disabling automatic
gain control(AGC) on this interface. AGC allows DSP
to adjust the input voice volume and avoid rapid
voice volume change.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.2.1.1.7

cvaIfEMStatusTable

table
.1.3.6.1.4.1.9.9.62.1.2.2 · 1 row entry · 2 columns
Open in standard view 
The E&M interface Table.  The table contains 
the status of the E&M tie trunk interface.
cvaIfEMStatusEntry entry .1.3.6.1.4.1.9.9.62.1.2.2.1
An entry in the status table for each E&M interface.
Indexes
No indexes recorded
Column Syntax OID
cvaIfEMInSeizureActive
This object contains the incoming seizure state of the E&M
interface. If the value is true, then the interface has an
incoming trunk seizure active; otherwise, it doesn't.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.2.2.1.1
cvaIfEMOutSeizureActive
This object contains the outgoing seizure state of the E&M
interface. If the value is true, then the interface has an
outgoing trunk seizure active; otherwise, it doesn't.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.2.2.1.2

cvaIfEMTimingTable

table
.1.3.6.1.4.1.9.9.62.1.2.3 · 1 row entry · 15 columns
Open in standard view 
The E&M tie trunk Timing Parameters table. It 
contains the configuration of the various E&M signaling
protocol timing parameters.
cvaIfEMTimingEntry entry .1.3.6.1.4.1.9.9.62.1.2.3.1
An entry in the E&M Timing Parameters Table for
each E&M interface.
Indexes
No indexes recorded
Column Syntax OID
cvaIfEMTimingDigitDuration
Outgoing DTMF digit duration in milliseconds.
millisecondsInteger32r/w
Constraints:
range: 50-500
 .1.3.6.1.4.1.9.9.62.1.2.3.1.1
cvaIfEMTimingInterDigitDuration
Outgoing DTMF inter-digit duration in milliseconds.
millisecondsInteger32r/w
Constraints:
range: 50-500
 .1.3.6.1.4.1.9.9.62.1.2.3.1.2
cvaIfEMTimingPulseRate
Outgoing pulse dialing rate in pulses per second (pps).
pulses per secondInteger32r/w
Constraints:
range: 10-20
 .1.3.6.1.4.1.9.9.62.1.2.3.1.3
cvaIfEMTimingPulseInterDigitDuration
Outgoing Pulse dialing inter-digit timing in
milliseconds.
millisecondsInteger32r/w
Constraints:
range: 100-1000
 .1.3.6.1.4.1.9.9.62.1.2.3.1.4
cvaIfEMTimingClearWaitDuration
Time of Inactive seizure signal to declare call cleared.
millisecondsInteger32r/w
Constraints:
range: 200-2000
 .1.3.6.1.4.1.9.9.62.1.2.3.1.5
cvaIfEMTimingMaxWinkWaitDuration
Maximum time to wait from the outgoing seizure of the line
to the time of sending out a wink-pulse.
millisecondsInteger32r/w
Constraints:
range: 100-5000
 .1.3.6.1.4.1.9.9.62.1.2.3.1.6
cvaIfEMTimingMaxWinkDuration
Maximum outgoing wink duration (between the wink-pulse leading
edge and trailing edge) for wink start signaling.
millisecondsInteger32r/w
Constraints:
range: 100-3000
 .1.3.6.1.4.1.9.9.62.1.2.3.1.7
cvaIfEMTimingDelayStart
Minimum time to wait from outgoing seizure to
out-dialing digits for delay start signaling.
millisecondsInteger32r/w
Constraints:
range: 20-2000
 .1.3.6.1.4.1.9.9.62.1.2.3.1.8
cvaIfEMTimingMaxDelayDuration
Maximum time to wait from outgoing seizure to
out-dialing digits. If the far end does not allow to
send digits after the duration specified in the object,
a reorder tone will be sent to the calling party.
millisecondsInteger32r/w
Constraints:
range: 100-5000
 .1.3.6.1.4.1.9.9.62.1.2.3.1.9
cvaIfEMTimingMinDelayPulseWidth
Minimum delay-dial pulse duration for incoming call.
If the value of this object is 0, then no delay-dial
is sent to the far end for the incoming call.
millisecondsInteger32r/w
Constraints:
range: 140-5000
range: 0-0
 .1.3.6.1.4.1.9.9.62.1.2.3.1.10
cvaIfEMTimingVoiceHangover
The hangover time used to determine the casethere is
no more voice packet arrived.
millisecondsInteger32r/w
Constraints:
range: 0-10000
 .1.3.6.1.4.1.9.9.62.1.2.3.1.11
cvaIfEMTimeoutLmrTeardown
LMR port tear down timeout.
This object is relevant to the waiting time of
teardown call on LMR port.
if the value of this object is '-1', then the timeout
is disable.
secondsInteger32r/w
Constraints:
range: -1--1
range: 5-60000
 .1.3.6.1.4.1.9.9.62.1.2.3.1.12
cvaIfEMTimeoutPttXmt
This object signifies LMR port maxinum transmit time.
This object is relevant to how long LMR port can
continue transmit voice packet without pause.
minutesInteger32r/w
Constraints:
range: 0-30
 .1.3.6.1.4.1.9.9.62.1.2.3.1.13
cvaIfEMTimeoutPttRcv
This object signifies LMR port maxinum receive time.
This object is relevant to how long LMR port can
continue receive voice packet without pause.
minutesInteger32r/w
Constraints:
range: 0-30
 .1.3.6.1.4.1.9.9.62.1.2.3.1.14
cvaIfEMTimingDelayVoice
This object is relevant to how long DSP will delay
sending the voice packet to the LMR port.
millisecondsInteger32r/w
Constraints:
range: 0-1500
 .1.3.6.1.4.1.9.9.62.1.2.3.1.15

cvaIfFXOCfgTable

table
.1.3.6.1.4.1.9.9.62.1.3.1 · 1 row entry · 5 columns
Open in standard view 
The FXO standard configuration table. It contains 
FXO configuration parameters, one entry per FXO interface.
The configuration information of this table is set by 
hardware with its default setting or CLI during the hardware 
installation time.
cvaIfFXOCfgEntry entry .1.3.6.1.4.1.9.9.62.1.3.1.1
An entry in the standard configuration table for
each FXO interface.
Indexes
IF-MIBifIndex
Column Syntax OID
cvaIfFXOCfgSignalType
the signaling type of FXO interface.
fxoLoopStart - loop start.
fxoGroundStart - ground start.
fxoCama - cama.
Enumerationr/w
Enumerated Values:
1fxoLoopStart
2fxoGroundStart
3fxoCama
 .1.3.6.1.4.1.9.9.62.1.3.1.1.1
cvaIfFXOCfgNumberRings
The number of rings detected before closing loop.
ringsInteger32r/w
Constraints:
range: 1-10
 .1.3.6.1.4.1.9.9.62.1.3.1.1.2
cvaIfFXOCfgSupDisconnect deprecated
Specifies whether a supervisory disconnect signal (CPC) will
be presented to the interface when the connected party at
the interface hangs up.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.3.1.1.3
cvaIfFXOCfgDialType
Specifies the out dialing type of FXO interface.
InterfaceDialTyper/w
Textual Convention: InterfaceDialType Enumeration
Type Values:
1dtmf
2pulse
3mf
 .1.3.6.1.4.1.9.9.62.1.3.1.1.4
cvaIfFXOCfgSupDisconnect2
Specifies the type of supervisory disconnect signal
(CPC) to be presented to the interface when the
connected party at the interface hangs up.
signal - power denial recognition
anytone - tone detection of all call pro…
Enumerationr/w
Enumerated Values:
0signal
1anytone
2dualtoneMidcall
3dualtonePreconnect
 .1.3.6.1.4.1.9.9.62.1.3.1.1.5

cvaIfFXOStatusTable

table
.1.3.6.1.4.1.9.9.62.1.3.2 · 1 row entry · 4 columns
Open in standard view 
The Foreign Exchange Office (FXO) interface Status Table.
It contains hook status, ring detection and other states of
the interface.
cvaIfFXOStatusEntry entry .1.3.6.1.4.1.9.9.62.1.3.2.1
An entry in the status table for each FXO interface.
Indexes
No indexes recorded
Column Syntax OID
cvaIfFXOHookStatus
This object contains the hook status of FXO interface.
onHook - Present the onHook to the connected equipment.
offHook - Present the offHook to the connected equipment.
trunked - Present the trunk to the connected equi…
Enumeration
Enumerated Values:
1onHook
2offHook
3trunked
 .1.3.6.1.4.1.9.9.62.1.3.2.1.1
cvaIfFXORingDetect
This object contains the ring detect indication. If the
value is true, then the interface detects ring from PBX or
CO; otherwise, it doesn't.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.3.2.1.2
cvaIfFXORingGround
This object contains the incoming ring ground indication.
It is only valid when the cvaIfFXOCfgSignalType is
fxoGroundStart. If the object is true, then the interface
is presenting a ring ground to the connected equipm…
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.3.2.1.3
cvaIfFXOTipGround
This object contains the incoming tip ground indication.
It is only valid when the cvaIfFXOCfgSignalType is
fxoGroundStart. If the object is true, then the interface
is detecting a tip ground at the interface; otherwis…
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.3.2.1.4

cvaIfFXOTimingTable

table
.1.3.6.1.4.1.9.9.62.1.3.3 · 1 row entry · 4 columns
Open in standard view 
The FXO interface Timing Parameters table. It 
contains the configuration of the various FXO signaling
protocol timing parameters.
cvaIfFXOTimingEntry entry .1.3.6.1.4.1.9.9.62.1.3.3.1
An entry in the FXO Timing Parameters Table for
each FXO interface.
Indexes
No indexes recorded
Column Syntax OID
cvaIfFXOTimingDigitDuration
Outgoing DTMF digit duration in milliseconds.
millisecondsInteger32r/w
Constraints:
range: 50-500
 .1.3.6.1.4.1.9.9.62.1.3.3.1.1
cvaIfFXOTimingInterDigitDuration
Outgoing DTMF inter-digit duration in milliseconds.
millisecondsInteger32r/w
Constraints:
range: 50-500
 .1.3.6.1.4.1.9.9.62.1.3.3.1.2
cvaIfFXOTimingPulseRate
Outgoing pulse dialing rate in pulses per second (pps).
pulses per secondInteger32r/w
Constraints:
range: 10-20
 .1.3.6.1.4.1.9.9.62.1.3.3.1.3
cvaIfFXOTimingPulseInterDigitDuration
Outgoing pulse dialing inter-digit timing in milliseconds.
millisecondsInteger32r/w
Constraints:
range: 100-1000
 .1.3.6.1.4.1.9.9.62.1.3.3.1.4

cvaIfFXSCfgTable

table
.1.3.6.1.4.1.9.9.62.1.4.1 · 1 row entry · 2 columns
Open in standard view 
The FXS standard configuration table. It contains
FXS configuration parameters, one entry per FXS interface.
The configuration information of this table is set by 
hardware with its default setting or CLI during the hardware 
installation time.
cvaIfFXSCfgEntry entry .1.3.6.1.4.1.9.9.62.1.4.1.1
An entry in the standard configuration table for
each FXS interface.
Indexes
IF-MIBifIndex
Column Syntax OID
cvaIfFXSCfgSignalType
the signaling type of FXS interface.
fxsLoopStart - loop start.
fxsGroundStart - ground start.
Enumerationr/w
Enumerated Values:
1fxsLoopStart
2fxsGroundStart
 .1.3.6.1.4.1.9.9.62.1.4.1.1.1
cvaIfFXSRingFrequency
the ring frequency to be used in the FXS interface.
ringFrequency25 - ring frequency 25 Hertz.
ringFrequency50 - ring frequency 50 Hertz.
ringFrequency20 - ring frequency 20 Hertz.
ringFrequency30 - ring frequency …
Enumerationr/w
Enumerated Values:
1ringFrequency25
2ringFrequency50
3ringFrequency20
4ringFrequency30
 .1.3.6.1.4.1.9.9.62.1.4.1.1.2

cvaIfFXSStatusTable

table
.1.3.6.1.4.1.9.9.62.1.4.2 · 1 row entry · 4 columns
Open in standard view 
The Foreign Exchange Station (FXS) interface Status Table.
It contains hook status, ring active and other states of
the interface.
cvaIfFXSStatusEntry entry .1.3.6.1.4.1.9.9.62.1.4.2.1
An entry in the status table for each FXS interface.
Indexes
No indexes recorded
Column Syntax OID
cvaIfFXSHookStatus
This object contains the hook status of FXS interface.
onHook - the connected equipment(e.g., phone) is onHook.
offHook - the connected equipment is offHook.
trunked - the connected equipment is trunked.
Enumeration
Enumerated Values:
1onHook
2offHook
3trunked
 .1.3.6.1.4.1.9.9.62.1.4.2.1.1
cvaIfFXSRingActive
This object contains the outgoing ring active indication. If
the object value is true, then the interface is currently
generating ring out to the Key Telephone System (KTS) or
Plain Old Telephone (POT); otherwise, it d…
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.4.2.1.2
cvaIfFXSRingGround
This object contains the incoming ring ground indication.
It is only valid when the cvaIfFXSCfgSignalType is
fxsGroundStart. If the object is true, then the interface
is presenting a ring ground to the connected equipm…
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.4.2.1.3
cvaIfFXSTipGround
This object contains the incoming tip ground indication.
It is only valid when the cvaIfFXSCfgSignalType is
fxsGroundStart. If the object is true, then the interface
is detecting a tip ground at the interface; otherwis…
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.62.1.4.2.1.4

cvaIfFXSTimingTable

table
.1.3.6.1.4.1.9.9.62.1.4.3 · 1 row entry · 2 columns
Open in standard view 
The FXS interface Timing Parameters table. It 
contains the configuration of the various FXS signaling
protocol timing parameters.
cvaIfFXSTimingEntry entry .1.3.6.1.4.1.9.9.62.1.4.3.1
An entry in the FXS Timing Parameters Table for
each FXS interface.
Indexes
No indexes recorded
Column Syntax OID
cvaIfFXSTimingDigitDuration
Outgoing DTMF digit duration in milliseconds.
millisecondsInteger32r/w
Constraints:
range: 50-500
 .1.3.6.1.4.1.9.9.62.1.4.3.1.1
cvaIfFXSTimingInterDigitDuration
Outgoing DTMF inter-digit duration in milliseconds.
millisecondsInteger32r/w
Constraints:
range: 50-500
 .1.3.6.1.4.1.9.9.62.1.4.3.1.2