CISCO-DYNAMIC-TEMPLATE-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
10
Rows
10
Columns
113

cdtTemplateTable

table
.1.3.6.1.4.1.9.9.784.1.1.1 · 1 row entry · 6 columns
Open in standard view 
This table lists the dynamic templates maintained by the
system, including those that have been locally-configured on the
system and those pushed to the system by external policy
servers.
cdtTemplateEntry entry .1.3.6.1.4.1.9.9.784.1.1.1.1
An entry describes a dynamic template, which serves as a
container for configuration attributes. The configuration
attributes contained by a dynamic template depends on its type.

The system automatically c…
Indexes
cdtTemplateName
Column Syntax OID
cdtTemplateName
This object indicates a string-value that uniquely identifies
the dynamic template.

If the corresponding instance of cdtTemplateSrc is not
'local', then the system automatically generates the name
identif…
CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateName
Textual Convention: CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateName OctetString
Type Constraints:
range: 1..64
 .1.3.6.1.4.1.9.9.784.1.1.1.1.1
cdtTemplateStatus
This object specifies the status of the dynamic template. The
following columns must be valid before activating a dynamic
template:

- cdtTemplateStorage
- cdtTemplateType

However, …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.784.1.1.1.1.2
cdtTemplateStorage
This object specifies what happens to the dynamic template
upon restart.

If the corresponding instance of cdtTemplateSrc is not
'local', then this column must be 'volatile'.
SNMPv2-TCStorageTyper/w
Textual Convention: SNMPv2-TCStorageType Enumeration
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
 .1.3.6.1.4.1.9.9.784.1.1.1.1.3
cdtTemplateType
This object indicates the types of dynamic template.
CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateTyper/w
Textual Convention: CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateType Enumeration
Type Values:
1other
2derived
3ppp
4ethernet
5ipSubscriber
6service
 .1.3.6.1.4.1.9.9.784.1.1.1.1.4
cdtTemplateSrc
This object specifies the source of the dynamic template:

'other'
The implementation of the MIB module does not recognize the
source of the dynamic template.

'derived'
The syste…
Enumeration
Enumerated Values:
1other
2derived
3local
4aaaUserProfile
5aaaServiceProfile
 .1.3.6.1.4.1.9.9.784.1.1.1.1.5
cdtTemplateUsageCount
This object specifies the number of targets using a dynamic template
Unsigned32
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.9.9.784.1.1.1.1.6

cdtTemplateTargetTable

table
.1.3.6.1.4.1.9.9.784.1.1.2 · 1 row entry · 4 columns
Open in standard view 
This table contains a list of targets associated with
one or more dynamic templates.
cdtTemplateTargetEntry entry .1.3.6.1.4.1.9.9.784.1.1.2.1
An entry describes a target associated with one or more
dynamic templates.

The system automatically creates an entry when it associates a
dynamic template to a target. Likewise, the system
automatically de…
Indexes
cdtTemplateTargetType cdtTemplateTargetId
Column Syntax OID
cdtTemplateTargetType
This object indicates the type of target.
CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateTargetType
Textual Convention: CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateTargetType Enumeration
Type Values:
1other
2interface
 .1.3.6.1.4.1.9.9.784.1.1.2.1.1
cdtTemplateTargetId
This object uniquely identifies the target within the scope of
its type.
CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateTargetId
Textual Convention: CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateTargetId OctetString
Type Constraints:
range: 1..20
 .1.3.6.1.4.1.9.9.784.1.1.2.1.2
cdtTemplateTargetStatus
This object specifies the status of the dynamic template
target. The following columns must be valid before activating a
subscriber access profile:

- cdtTemplateTargetStorage

However, …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.784.1.1.2.1.3
cdtTemplateTargetStorage
This object specifies what happens to the dynamic template
target upon restart.
SNMPv2-TCStorageTyper/w
Textual Convention: SNMPv2-TCStorageType Enumeration
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
 .1.3.6.1.4.1.9.9.784.1.1.2.1.4

cdtTemplateAssociationTable

table
.1.3.6.1.4.1.9.9.784.1.1.3 · 1 row entry · 2 columns
Open in standard view 
This table contains a list of templates associated with each
target.
          
This table has an expansion dependent relationship on the
cdtTemplateTargetTable, containing zero or more rows for each
target.
cdtTemplateAssociationEntry entry .1.3.6.1.4.1.9.9.784.1.1.3.1
An entry indicates an association of a dynamic template with a
target.

The system automatically creates an entry when it associates a
dynamic template to a target.

The system also creates an en…
Indexes
cdtTemplateTargetType cdtTemplateTargetId cdtTemplateAssociationName
Column Syntax OID
cdtTemplateAssociationName
This object indicates the name of the template associated with
the target.
CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateName
Textual Convention: CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateName OctetString
Type Constraints:
range: 1..64
 .1.3.6.1.4.1.9.9.784.1.1.3.1.1
cdtTemplateAssociationPrecedence
This object indicates the relative precedence of the
associated dynamic template. Lower values have higher
precedence than higher values.
Unsigned32
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.9.9.784.1.1.3.1.2

cdtTemplateUsageTable

table
.1.3.6.1.4.1.9.9.784.1.1.4 · 1 row entry · 2 columns
Open in standard view 
This table contains a list of targets using each dynamic
template.
          
This table has an expansion dependent relationship on the
cdtTemplateTable, containing zero or more rows for each
dynamic template.
cdtTemplateUsageEntry entry .1.3.6.1.4.1.9.9.784.1.1.4.1
An entry indicates a target using the dynamic template.

The system automatically creates an entry when it associates a
dynamic template to a target.

The system also creates an entry when it der…
Indexes
cdtTemplateName cdtTemplateUsageTargetType cdtTemplateUsageTargetId
Column Syntax OID
cdtTemplateUsageTargetType
This object indicates the type of target using the
dynamic template.
CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateTargetType
Textual Convention: CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateTargetType Enumeration
Type Values:
1other
2interface
 .1.3.6.1.4.1.9.9.784.1.1.4.1.1
cdtTemplateUsageTargetId
This object indicates the name of the target using the dynamic
template
CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateTargetId
Textual Convention: CISCO-DYNAMIC-TEMPLATE-TC-MIBDynamicTemplateTargetId OctetString
Type Constraints:
range: 1..20
 .1.3.6.1.4.1.9.9.784.1.1.4.1.2

cdtTemplateCommonTable

table
.1.3.6.1.4.1.9.9.784.1.1.5 · 1 row entry · 15 columns
Open in standard view 
This table contains attributes relating to all dynamic
templates.  Observe that the type of dynamic templates
containing these attributes may change with the addition of new
dynamic template types.
          
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
          
    'derived'
    'ppp'
    'ethernet'
    'ipSubscriber'
    'service'
cdtTemplateCommonEntry entry .1.3.6.1.4.1.9.9.784.1.1.5.1
An entry containing attributes relating to any target.

The system automatically creates an entry when the system or the
EMS/NMS creates a row in the cdtTemplateTable with a
cdtTemplateType of on the followi…
Indexes
cdtTemplateName
Column Syntax OID
cdtCommonValid
This object specifies which attributes in the dynamic template
have been configured to valid values.

Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value o…
Bitsr/w
Enumerated Values:
0descr
1keepalive
2vrf
3addrPool
4ipv4AccessGroup
5ipv4Unreachables
6ipv6AccessGroup
7ipv6Unreachables
8srvSubControl
9srvRedirect
10srvAcct
11srvQos
12srvNetflow
 .1.3.6.1.4.1.9.9.784.1.1.5.1.1
cdtCommonDescr
This object specifies a human-readable description for the
dynamic template.

This column is valid only if the 'descr' bit of the
corresponding instance of cdtCommonValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.1.5.1.2
cdtCommonKeepaliveInt
This object specifies the interval that the system sends
keepalive messages to a target.

This column is valid only if the 'keepaliveInterval' bit of the
corresponding instance of cdtCommonValid is '1'.
secondsUnsigned32r/w
Constraints:
range: 1-4294967295
 .1.3.6.1.4.1.9.9.784.1.1.5.1.3
cdtCommonKeepaliveRetries
This object specifies the number of times the system will
resend a keepalive message without a response before it
transitions a target to an operationally down state.

This column is valid only if the 'kee…
retriesUnsigned32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.9.9.784.1.1.5.1.4
cdtCommonVrf
This object specifies the name of the VRF with which a target
has an association.

This column is valid only if the 'vrf' bit of the corresponding
instance of cdtCommonValid is '1'.
CISCO-TCCiscoVrfNamer/w
Textual Convention: CISCO-TCCiscoVrfName OctetString
Type Constraints:
range: 0..32
 .1.3.6.1.4.1.9.9.784.1.1.5.1.5
cdtCommonAddrPool
This object specifies the name of the IP address pool the
system will use to assign an IP address to a peer of a target.

This column is valid only if the 'addrPool' bit of the
corresponding instance of cd…
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.1.5.1.6
cdtCommonIpv4AccessGroup
This object specifies the name (or number) of the IPv4 ACL
applied to a target.

This column is valid only if the 'ipv4AccessGroup' bit of the
corresponding instance of cdtCommonValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.1.5.1.7
cdtCommonIpv4Unreachables
This object specifies whether a target generates ICMPv4
unreachable messages.

This column is valid only if the 'ipv4Unreachables' bit of the
corresponding instance of cdtCommonValid is '1'.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.1.5.1.8
cdtCommonIpv6AccessGroup
This object specifies the name (or number) of the IPv4 ACL
applied to a target.

This column is valid only if the 'ipv6AccessGroup' bit of the
corresponding instance of cdtCommonValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.1.5.1.9
cdtCommonIpv6Unreachables
This object specifies whether a target generates ICMPv6
unreachable messages.

This column is valid only if the 'ipv6Unreachables' bit of the
corresponding instance of cdtCommonValid is '1'.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.1.5.1.10
cdtCommonSrvSubControl
This object specifies the name of the subscriber control
policy applied to a target.

The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is
cbpPmtContr…
CISCO-CBP-TC-MIBCbpElementNamer/w
Textual Convention: CISCO-CBP-TC-MIBCbpElementName OctetString
Type Constraints:
range: 0..127
 .1.3.6.1.4.1.9.9.784.1.1.5.1.11
cdtCommonSrvRedirect
This object specifies the name of the traffic redirect policy
applied to a target.

The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is
cbpPmtTraffic…
CISCO-CBP-TC-MIBCbpElementNamer/w
Textual Convention: CISCO-CBP-TC-MIBCbpElementName OctetString
Type Constraints:
range: 0..127
 .1.3.6.1.4.1.9.9.784.1.1.5.1.12
cdtCommonSrvAcct
This object specifies the name of the traffic accounting policy
applied to a target.

The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is
cbpPmtTraff…
CISCO-CBP-TC-MIBCbpElementNamer/w
Textual Convention: CISCO-CBP-TC-MIBCbpElementName OctetString
Type Constraints:
range: 0..127
 .1.3.6.1.4.1.9.9.784.1.1.5.1.13
cdtCommonSrvQos
This object specifies the name of the traffic QoS policy
applied to a target.

The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is cbpPmtQos (defined…
CISCO-CBP-TC-MIBCbpElementNamer/w
Textual Convention: CISCO-CBP-TC-MIBCbpElementName OctetString
Type Constraints:
range: 0..127
 .1.3.6.1.4.1.9.9.784.1.1.5.1.14
cdtCommonSrvNetflow
This object specifies the name of the NetFlow policy applied to
a target.

The system should assume that the cbpPolicyMapType (defined by
the CISCO-CBP-BASE-CFG-MIB) of the policy is
cbpPmtNetflow (defined…
CISCO-CBP-TC-MIBCbpElementNamer/w
Textual Convention: CISCO-CBP-TC-MIBCbpElementName OctetString
Type Constraints:
range: 0..127
 .1.3.6.1.4.1.9.9.784.1.1.5.1.15

cdtIfTemplateTable

table
.1.3.6.1.4.1.9.9.784.1.2.1 · 1 row entry · 30 columns
Open in standard view 
This table contains attributes relating to interface
configuration.
          
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
          
    'derived'
    'ppp'
    'ethernet'
    'ipSubscriber'
cdtIfTemplateEntry entry .1.3.6.1.4.1.9.9.784.1.2.1.1
An entry containing attributes relating to interface
configuration.

The system automatically creates an entry when the system or the
EMS/NMS creates a row in the cdtTemplateTable with a
cdtTemplateType of o…
Indexes
cdtTemplateName
Column Syntax OID
cdtIfValid
This object specifies which attributes in the dynamic template
have been configured to valid values.

Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value o…
Bitsr/w
Enumerated Values:
0mtu
1cdpEnable
2flowMonitor
3ipv4Unnumbered
4ipv4SubEnable
5ipv4Mtu
6ipv4TcpMssAdjust
7ipv4VerifyUniRpf
8ipv4VerifyUniRpfAcl
9ipv4VerifyUniRpfOpts
10ipv6Enable
11ipv6SubEnable
12ipv6TcpMssAdjust
13ipv6VerifyUniRpf
14ipv6VerifyUniRpfAcl
15ipv6VerifyUniRpfOpts
16ipv6NdPrefix
17ipv6NdValidLife
18ipv6NdPreferredLife
19ipv6NdOpts
20ipv6NdDadAttempts
21ipv6NdNsInterval
22ipv6NdReachableTime
23ipv6NdRaIntervalMax
24ipv6NdRaIntervalMin
25ipv6NdRaLife
26ipv6NdRaRouterPreference
 .1.3.6.1.4.1.9.9.784.1.2.1.1.1
cdtIfMtu
This object specifies the Maximum Transfer Unit (MTU) size for
all packets sent on the target interface.

The value '0' cannot be written to an instance of this object.
However, it serves as a convenient v…
octetsUnsigned32r/w
Constraints:
range: 0-0
range: 64-65535
 .1.3.6.1.4.1.9.9.784.1.2.1.1.2
cdtIfCdpEnable
This object specifies whether the target interface participates
in the Cisco Discovery Protocol (CDP).

This column is valid only if the 'cdpEnable' bit of the
corresponding instance of cdtIfValid is '1'.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.2.1.1.3
cdtIfFlowMonitor
This object specifies the name of the flow monitor associated
with the target interface.

This column is valid only if the 'flowMonitor' bit of the
corresponding instance of cdtIfValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.2.1.1.4
cdtIfIpv4Unnumbered
This object specifies the interface of the source address that
the target interface uses when originating IPv4 packets.

The value '0' cannot be written to an instance of this object.
However, it serves as…
IF-MIBInterfaceIndexOrZeror/w
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.9.9.784.1.2.1.1.5
cdtIfIpv4SubEnable
This object specifies whether the target interface allows IPv4
subscriber sessions.

This column is valid only if the 'ipv4SubEnable' bit of the
corresponding instance of cdtIfValid is '1'.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.2.1.1.6
cdtIfIpv4Mtu
This object specifies the Maximum Transfer Unit (MTU) size for
IPv4 packets sent on the target interface.

The value '0' cannot be written to an instance of this object.
However, it serves as a convenient …
octetsUnsigned32r/w
Constraints:
range: 128-65535
range: 0-0
 .1.3.6.1.4.1.9.9.784.1.2.1.1.7
cdtIfIpv4TcpMssAdjust
This object specifies the adjustment to the Maximum Segment
Size (MSS) of TCP SYN packets received by the target interface
contained in IPv4 datagrams.

The value '0' cannot be written to an instance of th…
octetsUnsigned32r/w
Constraints:
range: 0-0
range: 500-1460
 .1.3.6.1.4.1.9.9.784.1.2.1.1.8
cdtIfIpv4VerifyUniRpf
This object specifies whether the type of unicast RPF the
system performs on IPv4 packets received by the target
interface.

This column is valid only if the 'ipv4VerifyUniRpf' bit of the
corresponding ins…
CISCO-IP-URPF-MIBUnicastRpfTyper/w
Textual Convention: CISCO-IP-URPF-MIBUnicastRpfType Enumeration
Type Values:
1strict
2loose
3disabled
 .1.3.6.1.4.1.9.9.784.1.2.1.1.9
cdtIfIpv4VerifyUniRpfAcl
This object specifies the name (or number) of the IPv4 ACL
used to determine whether the system should permit/deny packets
received by the target interface that fail unicast RPF
verification.

This column …
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.2.1.1.10
cdtIfIpv4VerifyUniRpfOpts
This object specifies the options that affect how the system
performs unicast RPF on IPv4 packets received by the target
interface.

This column is valid only if the 'ipv4VerifyUniRpfOpts' bit of
the corre…
CISCO-IP-URPF-MIBUnicastRpfOptionsr/w
Textual Convention: CISCO-IP-URPF-MIBUnicastRpfOptions Bits
Type Values:
0allowDefault
1allowSelfPing
 .1.3.6.1.4.1.9.9.784.1.2.1.1.11
cdtIfIpv6Enable
This object specifies whether the system processes IPv6
packets received by the target interface.

This column is valid only if the 'ipv6Enable' bit of the
corresponding instance of cdtIfValid is '1'.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.2.1.1.12
cdtIfIpv6SubEnable
This object specifies whether the target interface allows IPv6
subscriber sessions.

This column is valid only if the 'ipv6SubEnable' bit of the
corresponding instance of cdtIfValid is '1'.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.2.1.1.13
cdtIfIpv6TcpMssAdjust
This object specifies the adjustment to the Maximum Segment
Size (MSS) of TCP SYN packets received by the target interface
contained in IPv6 datagrams.

The value '0' cannot be written to an instance of th…
octetsUnsigned32r/w
Constraints:
range: 0-0
range: 500-1460
 .1.3.6.1.4.1.9.9.784.1.2.1.1.14
cdtIfIpv6VerifyUniRpf
This object specifies whether the type of unicast RPF the
system performs on IPv6 packets received by the target
interface.

This column is valid only if the 'ipv6VerifyUniRpf' bit of the
corresponding ins…
CISCO-IP-URPF-MIBUnicastRpfTyper/w
Textual Convention: CISCO-IP-URPF-MIBUnicastRpfType Enumeration
Type Values:
1strict
2loose
3disabled
 .1.3.6.1.4.1.9.9.784.1.2.1.1.15
cdtIfIpv6VerifyUniRpfAcl
This object specifies the name (or number) of the IPv6 ACL
used to determine whether the system should permit/deny packets
received by the target interface that fail unicast RPF
verification.

This column …
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.2.1.1.16
cdtIfIpv6VerifyUniRpfOpts
This object specifies the options that affect how the system
performs unicast RPF on IPv6 packets received by the target
interface.

This column is valid only if the 'ipv6VerifyUniRpfOpts' bit of
the corre…
CISCO-IP-URPF-MIBUnicastRpfOptionsr/w
Textual Convention: CISCO-IP-URPF-MIBUnicastRpfOptions Bits
Type Values:
0allowDefault
1allowSelfPing
 .1.3.6.1.4.1.9.9.784.1.2.1.1.17
cdtIfIpv6NdPrefix
This object specifies the IPv6 network number included in
IPv6 router advertisements sent on the target interface.

This column is valid only if the 'ipv6NdPrefix' bit of
the corresponding instance of cdtI…
INET-ADDRESS-MIBInetAddressIPv6r/w
Textual Convention: INET-ADDRESS-MIBInetAddressIPv6 OctetString
Type Constraints:
range: 16
 .1.3.6.1.4.1.9.9.784.1.2.1.1.18
cdtIfIpv6NdPrefixLength
This object specifies the length of the IPv6 prefix specified
by the corresponding instance of cdtIpv6NdPrefix.

This column is valid only if the 'ipv6NdPrefix' bit of the
corresponding instance of cdtIfVa…
INET-ADDRESS-MIBInetAddressPrefixLengthr/w
Textual Convention: INET-ADDRESS-MIBInetAddressPrefixLength Unsigned32
Type Constraints:
range: 0..2040
 .1.3.6.1.4.1.9.9.784.1.2.1.1.19
cdtIfIpv6NdValidLife
This object specifies the interval that the system advertises
the IPv6 prefix (i.e., the corresponding instance of
cdtIfIpv6NdPrefix) as 'valid' for IPv6 router advertisements
sent on the target interface.
…
secondsUnsigned32r/w
Constraints:
range: 1-4294967295
 .1.3.6.1.4.1.9.9.784.1.2.1.1.20
cdtIfIpv6NdPreferredLife
This object specifies the interval that the system advertises
the IPv6 prefix (i.e., the corresponding instance of
cdtIfIpv6NdPrefix) as 'preferred' for IPv6 router advertisements
sent on the target interface.
…
secondsUnsigned32r/w
Constraints:
range: 1-4294967295
 .1.3.6.1.4.1.9.9.784.1.2.1.1.21
cdtIfIpv6NdOpts
This object specifies options that affect advertisements sent
on the target interface:

'advertise'
This option specifies that the system should advertise
the IPv6 prefix (i.e., the cor…
Bitsr/w
Enumerated Values:
0advertise
1onlink
2router
3autoConfig
4advertisementInterval
5managedConfigFlag
6otherConfigFlag
7framedIpv6Prefix
8raSuppress
 .1.3.6.1.4.1.9.9.784.1.2.1.1.22
cdtIfIpv6NdDadAttempts
This object specifies the number of consecutive neighbor
solitication messages the system sends on the target interface
while performing duplicate address detection on unicast IPv6
addresses on the target interface. Th…
Unsigned32r/w
Constraints:
range: 0-600
 .1.3.6.1.4.1.9.9.784.1.2.1.1.23
cdtIfIpv6NdNsInterval
This object specifies the interval between neighbor
solicitation retransmissions on the target interface.

This column is valid only if the 'ipv6NdNsIntervals' bit of the
corresponding instance of cdtIfVal…
millisecondsUnsigned32r/w
Constraints:
range: 1000-3600000
 .1.3.6.1.4.1.9.9.784.1.2.1.1.24
cdtIfIpv6NdReachableTime
This object specifies the amount of time the system considers
a neighbor of the target interface reachable after a
reachability confirmation event has occurred. The value '0'
disables neighbor reachability detection on…
millisecondsUnsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.9.9.784.1.2.1.1.25
cdtIfIpv6NdRaIntervalUnits
This object specifies the units of time for the corresponding
instances of cdtIfIpv6NdRaIntervalMin and
cdtIfIpv6NdRaIntervalMax.

This column is valid only if the 'ipv6NdRaInterval' bit of the
correspondi…
Enumerationr/w
Enumerated Values:
1seconds
2milliseconds
 .1.3.6.1.4.1.9.9.784.1.2.1.1.26
cdtIfIpv6NdRaIntervalMax
This object specifies the maximum interval between IPv6 router
advertisements sent on the target interface.

The value '0' cannot be written to an instance of this object.
However, it serves as a convenien…
Unsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.9.9.784.1.2.1.1.27
cdtIfIpv6NdRaIntervalMin
This object specifies the minimum interval between IPv6 router
advertisements sent on the target interface. The value of this
column has the following restrictions:

1) This value cannot be less than 75%…
Unsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.9.9.784.1.2.1.1.28
cdtIfIpv6NdRaLife
This object specifies the router lifetime value in IPv6 router
advertisements sent on the target interface. The value '0'
specifies that neighbors should not consider the router as a
default router.
secondsUnsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.9.9.784.1.2.1.1.29
cdtIfIpv6NdRouterPreference
This object specifies the Default Router Preference (DRP) for
the router on the target interface.

This column is valid only if the 'ipv6NdRouterPreference' bit of
the corresponding instance of cdtIfValid …
Enumerationr/w
Enumerated Values:
1high
2medium
3low
 .1.3.6.1.4.1.9.9.784.1.2.1.1.30

cdtPppTemplateTable

table
.1.3.6.1.4.1.9.9.784.1.3.1 · 1 row entry · 39 columns
Open in standard view 
This table contains attributes relating to PPP connection
configuration.
          
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
          
    'derived'
    'ppp'
cdtPppTemplateEntry entry .1.3.6.1.4.1.9.9.784.1.3.1.1
An entry containing attributes relating to PPP connection
configuration.

The system automatically creates an entry when the system or the
EMS/NMS creates a row in the cdtTemplateTable with a
cdtTemplateType…
Indexes
cdtTemplateName
Column Syntax OID
cdtPppValid
This object specifies which attributes in the dynamic template
have been configured to valid values.

Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value o…
Bitsr/w
Enumerated Values:
0valid
1accounting
2authentication
3autthenticationMethods
4authorization
5loopbackIgnore
6maxBadAuth
7maxConfigure
8maxFailure
9maxTerminate
10timeoutAuthentication
11timeoutRetry
12chapOpts
13chapHostname
14chapPassword
15msChapV1Opts
16msChapV1Hostname
17msChapV1Password
18msChapV2Opts
19msChapV2Hostname
20msChapV2Password
21papOpts
22papUsername
23papPassword
24eapOpts
25eapIdentity
26eapPassword
27ipcpAddrOption
28ipcpDnsOption
29ipcpDnsPrimary
30ipcpDnsSecondary
31ipcpWinsOption
32ipcpWinsPrimary
33ipcpWinsSecondary
34ipcpMaskOption
35ipcpMask
36peerDefIpAddrOpts
37peerDefIpAddrSrc
38peerDefIpAddr
 .1.3.6.1.4.1.9.9.784.1.3.1.1.1
cdtPppAccounting
This object specifies whether the system applies accounting
services to the target PPP connection.

This column is valid only if the 'accounting' bit of the
corresponding instance of cdtPppValid is '1'.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.3.1.1.2
cdtPppAuthentication
This object specifies authentication services applied to a
target PPP connection and other options affecting authentication
services:

'chap'
This option enables the Challenge Handshake Protoco…
Bitsr/w
Enumerated Values:
0chap
1msChap
2msChapV2
3pap
4eap
5optional
6callin
7oneTime
 .1.3.6.1.4.1.9.9.784.1.3.1.1.3
cdtPppAuthenticationMethods
This object specifies the name of a list of authentication
methods used on a target PPP connection. If the template does
not include this attribute, then the system uses the default
method list.

This col…
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.4
cdtPppAuthorization
This object specifies whether the system applies authorization
services to a target PPP connection.

This column is valid only if the 'authorization' bit of the
corresponding instance of cditPppValid is '1…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.3.1.1.5
cdtPppLoopbackIgnore
This object specifies whether the system ignores loopback on
a target PPP connection. When the system ignores loopback,
loopback detection is disabled.

This column is valid only if the 'loopbackIgnore' b…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.3.1.1.6
cdtPppMaxBadAuth
This object specifies the number of authentication failures
allowed by the system before a target PPP connection is reset.

The value '0' cannot be written to an instance of this object.
However, it serves…
Unsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.9.9.784.1.3.1.1.7
cdtPppMaxConfigure
This object specifies the number of unacknowledged
Configure-Request messages a target PPP connection can send
before the system abandons LCP or NCP negotiations.

This column is valid only if the 'maxConf…
Unsigned32r/w
Constraints:
range: 1-4294967295
 .1.3.6.1.4.1.9.9.784.1.3.1.1.8
cdtPppMaxFailure
This object specifies the number of Configure-Nak messages a
target PPP connection can receive before the system abandons LCP
or NCP negotiations.

This column is valid only if the 'maxFailure' bit of the
…
Unsigned32r/w
Constraints:
range: 1-4294967295
 .1.3.6.1.4.1.9.9.784.1.3.1.1.9
cdtPppMaxTerminate
This object specifies the number of unacknowledged
Terminate-Request messages a target PPP connection can send
before the system abandons LCP or NCP negotiations.

This column is valid only if the 'maxTerm…
Unsigned32r/w
Constraints:
range: 1-4294967295
 .1.3.6.1.4.1.9.9.784.1.3.1.1.10
cdtPppTimeoutAuthentication
This objects specifies the maximum time the system will wait
for a response to an authentication request on a target PPP
connection.

This column is valid only if the 'timeoutAuthentication' bit of
the cor…
secondsUnsigned32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.11
cdtPppTimeoutRetry
This objects specifies the maximum time the system will wait
for a response to a PPP control packets on a target PPP
connection.

This column is valid only if the 'timeoutRetry' bit of the
corresponding in…
secondsUnsigned32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.12
cdtPppChapOpts
This object specifies how the system processes the CHAP on a
target PPP connection:

'refuse'
This option specifies that the system should refuse CHAP
requests from peers of a target PP…
Bitsr/w
Enumerated Values:
0refuse
1callin
2wait
3encrypted
 .1.3.6.1.4.1.9.9.784.1.3.1.1.13
cdtPppChapHostname
This object specifies the hostname sent in a CHAP response
on a target PPP connection. If the template does not include
this attribute, then the system uses its assigned hostname.

This column is valid on…
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.14
cdtPppChapPassword
This object specifies the password used to construct a CHAP
response on the target PPP connection.

This column is valid only if the 'chapPassword' bit of the
corresponding instance of cdtPppValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.15
cdtPppMsChapV1Opts
This object specifies how the system processes version 1 of
Microsoft CHAP on a target PPP connection:

'refuse'
This option specifies that the system should refuse
Microsoft CHAP (v1) …
Bitsr/w
Enumerated Values:
0refuse
1callin
2wait
3encrypted
 .1.3.6.1.4.1.9.9.784.1.3.1.1.16
cdtPppMsChapV1Hostname
This object specifies the hostname sent in a Microsoft CHAP
(v1) response on a target PPP connection. If the template does
not include this attribute, then the system uses its assigned
hostname.

This col…
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.17
cdtPppMsChapV1Password
This object specifies the password used to construct a
Microsoft CHAP (v1) response on a target PPP connection.

This column is valid only if the 'msChapV1Password' bit of the
corresponding instance of cdt…
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.18
cdtPppMsChapV2Opts
This object specifies how the system processes version 2 of
Microsoft CHAP on a target PPP connection:

'refuse'
This option specifies that the system should refuse
Microsoft CHAP (v2) …
Bitsr/w
Enumerated Values:
0refuse
1callin
2wait
3encrypted
 .1.3.6.1.4.1.9.9.784.1.3.1.1.19
cdtPppMsChapV2Hostname
This object specifies the hostname sent in a Microsoft CHAP
(v2) response on a target PPP connection. If the template does
not include this attribute, then the system uses its assigned
hostname.

This col…
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.20
cdtPppMsChapV2Password
This object specifies the password used to construct a
Microsoft CHAP (v2) response on a target PPP connection.

This column is valid only if the 'msChapV2Password' bit of the
corresponding instance of cdt…
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.21
cdtPppPapOpts
This object specifies how the system processes the PAP on a
target PPP connection:

'refuse'
This option specifies that the system should refuse PAP
requests from peers of a target PPP …
Bitsr/w
Enumerated Values:
0refuse
1encrypted
 .1.3.6.1.4.1.9.9.784.1.3.1.1.22
cdtPppPapUsername
This object specifies the username sent in a PAP response on
a target PPP connection.

This column is valid only if the 'papUsername' bit of the
corresponding instance of cdtPppValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.23
cdtPppPapPassword
This object specifies the username used to construct a PAP
response on a target PPP connection.

This column is valid only if the 'papPassword' bit of the
corresponding instance of cdtPppValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.24
cdtPppEapOpts
This object specifies how the system processes the EAP on a
target PPP connection:

'refuse'
This option specifies that the system should refuse EAP
requests from peers of a target PPP …
Bitsr/w
Enumerated Values:
0refuse
1callin
2wait
3local
 .1.3.6.1.4.1.9.9.784.1.3.1.1.25
cdtPppEapIdentity
This object specifies the identity sent in an EAP response on
a target PPP connection.

This column is valid only if the 'eapIdentity' bit of the
corresponding instance of cdtPppValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.26
cdtPppEapPassword
This object specifies the password used to construct an EAP
response on a target PPP connection.

This column is valid only if the 'eapPassword' bit of the
corresponding instance of cdtPppValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.1.1.27
cdtPppIpcpAddrOption
This object specifies the IPCP address option for a target PPP
connection:

'other'
The implementation of this MIB module does not recognize
the configured IPCP address option.
…
Enumerationr/w
Enumerated Values:
1other
2accept
3required
4unique
 .1.3.6.1.4.1.9.9.784.1.3.1.1.28
cdtPppIpcpDnsOption
This object specifies the IPCP DNS option for the dynamic
interface:

'other'
The implementation of this MIB module does not recognize
the configured DNS option.

'acc…
Enumerationr/w
Enumerated Values:
1other
2accept
3request
4reject
 .1.3.6.1.4.1.9.9.784.1.3.1.1.29
cdtPppIpcpDnsPrimary
This object specifies the IP address of the primary DNS server
offered to the peer of a target PPP connection.

This column is valid only if the 'ipcpDnsPrimary' bit of the
corresponding instance of cdtPpp…
INET-ADDRESS-MIBInetAddressIPv4r/w
Textual Convention: INET-ADDRESS-MIBInetAddressIPv4 OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.784.1.3.1.1.30
cdtPppIpcpDnsSecondary
This object specifies the IP address of the secondary DNS
server offered to the peer of a target PPP connection.

This column is valid only if the 'ipcpDnsSecondary' bit of the
corresponding instance of cd…
INET-ADDRESS-MIBInetAddressIPv4r/w
Textual Convention: INET-ADDRESS-MIBInetAddressIPv4 OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.784.1.3.1.1.31
cdtPppIpcpWinsOption
This object specifies the IPCP WINS option for a target PPP
connection:

'other'
The implementation of this MIB module does not recognize
the configured WINS option.

…
Enumerationr/w
Enumerated Values:
1other
2accept
3request
4reject
 .1.3.6.1.4.1.9.9.784.1.3.1.1.32
cdtPppIpcpWinsPrimary
This object specifies the IP address of the primary WINS server
offered to the peer of a target PPP connection.

This column is valid only if the 'ipcpWinsPrimary' bit of the
corresponding instance of cdtP…
INET-ADDRESS-MIBInetAddressIPv4r/w
Textual Convention: INET-ADDRESS-MIBInetAddressIPv4 OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.784.1.3.1.1.33
cdtPppIpcpWinsSecondary
This object specifies the IP address of the secondary WINS
server offered to the peer of a target PPP connection.

This column is valid only if the 'ipcpWinsSecondary' bit of the
corresponding instance of …
INET-ADDRESS-MIBInetAddressIPv4r/w
Textual Convention: INET-ADDRESS-MIBInetAddressIPv4 OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.784.1.3.1.1.34
cdtPppIpcpMaskOption
This object specifies the IPCP IP subnet mask option for a
target PPP connection:

'other'
The implementation of this MIB module does not recognize
the configured IP subnet mask option.…
Enumerationr/w
Enumerated Values:
1other
2request
3reject
 .1.3.6.1.4.1.9.9.784.1.3.1.1.35
cdtPppIpcpMask
This object specifies the IP address mask offered to the peer
of a target PPP connection.

This column is valid only if the 'ipcpMask' bit of the
corresponding instance of cdtPppValid is '1'.
INET-ADDRESS-MIBInetAddressIPv4r/w
Textual Convention: INET-ADDRESS-MIBInetAddressIPv4 OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.784.1.3.1.1.36
cdtPppPeerDefIpAddrOpts
This object specifies options that affect how the system
assigns an IP address to the peer of a target PPP connection:

'ipAddrForced'
This option forces the system to assign the next
a…
Bitsr/w
Enumerated Values:
0ipAddrForced
1matchAaaPools
2staticPool
 .1.3.6.1.4.1.9.9.784.1.3.1.1.37
cdtPppPeerDefIpAddrSrc
This object specifies how the system assigns an IP address to
the peer of a target PPP connection:

'static'
The system assigns the IP address specified by the
corresponding instance of…
Enumerationr/w
Enumerated Values:
1static
2pool
3dhcp
 .1.3.6.1.4.1.9.9.784.1.3.1.1.38
cdtPppPeerDefIpAddr
This object specifies the IP address the system assigns to the
peer of a target PPP connection.

This column is valid only if the 'peerDefIpAddr' bit of the
corresponding instance of cdtPppValid is '1'.
INET-ADDRESS-MIBInetAddressIPv4r/w
Textual Convention: INET-ADDRESS-MIBInetAddressIPv4 OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.9.9.784.1.3.1.1.39

cdtPppPeerIpAddrPoolTable

table
.1.3.6.1.4.1.9.9.784.1.3.2 · 1 row entry · 4 columns
Open in standard view 
This table contains a prioritized list of named pools for each
PPP template.  A list corresponding to a PPP template
specifies the pools the system searches in an attempt to
assign an IP address to the peer of a target PPP connection.
The system searches the pools in the order of their priority.
          
This table has an expansion dependent relationship on the
cdtPppTemplateTable, containing zero or more rows for each PPP
template.
cdtPppPeerIpAddrPoolEntry entry .1.3.6.1.4.1.9.9.784.1.3.2.1
An entry specifies a named pool in a list of pools associated
with a PPP template. A PPP template can only have named
pools associated with it if it has a cdtPppPeerIpAddrSrc of
'pool'.

Any attempt to crea…
Indexes
cdtTemplateName cdtPppPeerIpAddrPoolPriority
Column Syntax OID
cdtPppPeerIpAddrPoolPriority
This object indicates the relative priority of the named pool
in the list corresponding to a PPP template. The system
searches pools in the order of priority, where lower values
represent higher priority.
Unsigned32
Constraints:
range: 1-4294967295
 .1.3.6.1.4.1.9.9.784.1.3.2.1.1
cdtPppPeerIpAddrPoolStatus
This object specifies the status of the entry. The following
columns must be valid before activating a subscriber access
profile:

- cdtPppPeerIpAddrPoolStorage
- cdtPppPeerIpAddrPoolName
…
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.9.9.784.1.3.2.1.2
cdtPppPeerIpAddrPoolStorage
This object specifies what happens to the name pool entry upon
restart.

If the corresponding instance of cdtTemplateSrc is not 'local',
then this column must be 'volatile'.
SNMPv2-TCStorageTyper/w
Textual Convention: SNMPv2-TCStorageType Enumeration
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
 .1.3.6.1.4.1.9.9.784.1.3.2.1.3
cdtPppPeerIpAddrPoolName
This object specifies the name of the IP address pool
associated with the PPP template.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.3.2.1.4

cdtEthernetTemplateTable

table
.1.3.6.1.4.1.9.9.784.1.4.1 · 1 row entry · 5 columns
Open in standard view 
This table contains attributes relating to dynamic interfaces
initiated on Ethernet virtual interfaces (e.g., EoMPLS) or
automatically created VLANs.
          
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
          
    'derived'
    'ethernet'
cdtEthernetTemplateEntry entry .1.3.6.1.4.1.9.9.784.1.4.1.1
An entry containing attributes relating to dynamic interfaces
initiated on Ethernet virtual interfaces (e.g., EoMPLS) or
automatically created VLANs.

The system automatically creates an entry when the syste…
Indexes
cdtTemplateName
Column Syntax OID
cdtEthernetValid
This object specifies which attributes in the dynamic template
have been configured to valid values.

Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value o…
Bitsr/w
Enumerated Values:
0bridgeDomain
1pppoeEnable
2ipv4PointToPoint
3macAddr
 .1.3.6.1.4.1.9.9.784.1.4.1.1.1
cdtEthernetBridgeDomain
This object specifies the name of the bridge domain...
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.4.1.1.2
cdtEthernetPppoeEnable
This object specifies whether...
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.4.1.1.3
cdtEthernetIpv4PointToPoint
This object specifies whether...
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.4.1.1.4
cdtEthernetMacAddr
This object specifies the...
SNMPv2-TCMacAddressr/w
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.9.9.784.1.4.1.1.5

cdtSrvTemplateTable

table
.1.3.6.1.4.1.9.9.784.1.6.1 · 1 row entry · 6 columns
Open in standard view 
This table contains attributes relating to a service.
          
This table has a sparse-dependent relationship on the
cdtTemplateTable, containing a row for each dynamic template
having a cdtTemplateType of one of the following values:
          
    'derived'
    'service'
cdtSrvTemplateEntry entry .1.3.6.1.4.1.9.9.784.1.6.1.1
An entry containing attributes relating to a service.

The system automatically creates entry when the system or the
EMS/NMS creates a row in the cdtTemplateTable with a
cdtTemplateType of one of the followi…
Indexes
cdtTemplateName
Column Syntax OID
cdtSrvValid
This object specifies which attributes in the dynamic template
have been configured to valid values.

Each bit in this bit string corresponds to a column in this
table. If the bit is '0', then the value o…
Bitsr/w
Enumerated Values:
0networkSrv
1vpdnGroup
2sgSrvGroup
3sgSrvType
4multicast
 .1.3.6.1.4.1.9.9.784.1.6.1.1.1
cdtSrvNetworkSrv
This object specifies the type of network service provided by
the target service:

'other'
The implementation of this MIB module does not recognize
the configured network service.
…
Enumerationr/w
Enumerated Values:
1other
2none
3local
4vpdn
 .1.3.6.1.4.1.9.9.784.1.6.1.1.2
cdtSrvVpdnGroup
This object specifies the name of the VPDN group used to
configure the network service.

This column is valid only if the 'vpdnGroup' bit of the
corresponding instance of cdtSrvValid is '1'.
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.6.1.1.3
cdtSrvSgSrvGroup
This object specifies the name of the service group with which
the system associates subscriber sessions. A service group
specifies a set of services that may be active simultaneously
for a given subscriber session. T…
OctetStringr/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.784.1.6.1.1.4
cdtSrvSgSrvType
This object specifies whether the target service specifies a
network-forwarding policy:

'primary'
The target service specifies a network-forwarding
policy. Primary services are mutual…
Enumerationr/w
Enumerated Values:
1primary
2secondary
 .1.3.6.1.4.1.9.9.784.1.6.1.1.5
cdtSrvMulticast
This objects specifies whether the system enables multicast
service for subscriber sessions of the target service.

This column is valid only if the 'sgSrvMcastRoutingIf' bit of
the corresponding instance …
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.9.784.1.6.1.1.6