ADTRAN-TA5K-POTS-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
8
Rows
8
Columns
67

adTA5kPotsCardProvTable

table
.1.3.6.1.4.1.664.2.753.1.1.1 · 1 row entry · 9 columns
Open in standard view 
The POTS Card-level Provisioning table.
adTA5kPotsCardProvEntry entry .1.3.6.1.4.1.664.2.753.1.1.1.1
An entry in the POTS Card-level Provisioning Table.
Indexes
ADTRAN-GENSLOT-MIBadGenSlotInfoIndex
Column Syntax OID
adTA5kPotsCardProvRestoreFactoryDefaults
A set command will reset the POTS card. Get has
no meaning and will always return 1.
Enumerationr/w
Enumerated Values:
1reset
 .1.3.6.1.4.1.664.2.753.1.1.1.1.1
adTA5kPotsCardProvVoiceCallControl
The call-control protocol for all voice ports on this module -
1 = FXS Signaling (This is the same as tunneledGR303 in the syntax)
2 = ccSip
3 = MGCP
Enumerationr/w
Enumerated Values:
1tunneledGR303
2ccSip
3mgcp
 .1.3.6.1.4.1.664.2.753.1.1.1.1.2
adTA5kPotsCardReboot
This field sets the card into boot mode
1 = Reboot
Enumerationr/w
Enumerated Values:
1reboot
 .1.3.6.1.4.1.664.2.753.1.1.1.1.3
adTA5kPotsCardRemoveBatteryInOosUas
Remove CO battery from loop when a port is set to Out of Service - Unassigned.
This typically only applies to Combo ADSL/POTS units.
1 = Yes
2 = No
Enumerationr/w
Enumerated Values:
1yes
2no
 .1.3.6.1.4.1.664.2.753.1.1.1.1.4
adTA5kPotsCardProvLossOfTimingAlarm
Provisioning for Loss Of Timing Alarm which is a card level alarm.
1 = Enable
2 = Disable
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.1.1.1.1.5
adTA5kPotsCardProvAllAlarms
Provisioning for All Alarms (Card and Port Level).
1 = Enable
2 = Disable
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.1.1.1.1.6
adTA5kPotsCardLineTestScheduleEnable
Enable/Disable scheduled Fxs Line Tests.
If enabled, the card will run a GR-909 line test on each applicable fxs port at the time of day set by the adTA5kPotsCardLineTestScheduleTimeString oid.
If disabled, the card wil…
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.1.1.1.1.7
adTA5kPotsCardLoadCoilTestScheduleEnable
Enable/Disable scheduled Fxs Load Coil Tests.
If enabled, the card will run the load coil detection tests in addition to the GR-909 line tests at the time of day set by the adTA5kPotsCardLineTestScheduleTimeString oid.
…
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.1.1.1.1.8
adTA5kPotsCardLineTestScheduleTimeString
Set the scheduled start time of the Line Tests in 24 Hour Format HH:MM.
If adTA5kPotsCardLineTestScheduleEnable is disabled, then this oid has no effect.
OctetStringr/w
Constraints:
range: 5-5
 .1.3.6.1.4.1.664.2.753.1.1.1.1.9

adTA5kPotsPortProvTable

table
.1.3.6.1.4.1.664.2.753.1.2.1 · 1 row entry · 18 columns
Open in standard view 
The POTS Port-level Provisioning table.
adTA5kPotsPortProvEntry entry .1.3.6.1.4.1.664.2.753.1.2.1.1
An entry in the POTS Port-level Provisioning Table.
Indexes
IF-MIBifIndex
Column Syntax OID
adTA5kPotsPortMode
POTS port operational Mode -
1 = Loopstart
2 = Groundstart
3 = TR08 Single Party
4 = TR08 UVG
Enumerationr/w
Enumerated Values:
1loopStart
2groundStart
3tr08SingleParty
4tr08Uvg
 .1.3.6.1.4.1.664.2.753.1.2.1.1.1
adTA5kPotsPortImpedance
POTS port 2-wire termination impedance -
1 = 600 Ohms
2,3 are no longer supported
4 = 900 Ohms + 2.16 uF
5 = z1 - 220 + (820 // 115nF)
6 = z2 - 270 + (750 // 150nF)
7 = z3 - 270 + (750 // 150nF), Zin = 600r
8 = z4 - 320…
Enumerationr/w
Enumerated Values:
1ohm600
2ohm900
3ohm600Plus216uF
4ohm900Plus216uF
5ohmz1
6ohmz2
7ohmz3
8ohmz4
9ohmz5
10ohmz6
11ohmz7
12ohmz8
 .1.3.6.1.4.1.664.2.753.1.2.1.1.2
adTA5kPotsPortTXTLPString
POTS Port Transmit TLP -9.0dB to +6.0dB
OctetStringr/w
Constraints:
range: 0-4
 .1.3.6.1.4.1.664.2.753.1.2.1.1.3
adTA5kPotsPortRXTLPString
POTS Port Receive TLP -10.0dB to +6.0dB
OctetStringr/w
Constraints:
range: 0-4
 .1.3.6.1.4.1.664.2.753.1.2.1.1.4
adTA5kPotsPortOnHookMsg
POTS Port On-Hook Messaging -
1 = Enable
2 = Disable
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.1.2.1.1.5
adTA5kPotsPortTrunkConditioningAlarm
Provisioning for Enable/Disable Trunk Conditioning Alarm which is a port level alarm.
1 = Enable
2 = Disable
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.1.2.1.1.6
adTA5kPotsPortLineShoweringAlarm
Provisioning for Enable/Disable Line Showering Alarm which is a port level alarm.
1 = Enable
2 = Disable
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.1.2.1.1.7
adTA5kPotsPortAutoImpedanceMode
POTS Automatic Impedance Mode -
1 = Manual
2 = Automatic
Enumerationr/w
Enumerated Values:
1manual
2automatic
 .1.3.6.1.4.1.664.2.753.1.2.1.1.8
adTA5kPotsPortRingVoltage
POTS Ringer Voltage -
1 = 50 Vrms
2 = 60 Vrms
3 = 70 Vrms
4 = 80 Vrms
5 = 85 Vrms
6 = 90 Vrms
Enumerationr/w
Enumerated Values:
1fifty
2sixty
3seventy
4eighty
5eightyFive
6ninety
 .1.3.6.1.4.1.664.2.753.1.2.1.1.9
adTA5kPotsPortImpedanceByLoopLength
POTS port 2-wire termination impedance by loop length-
1 = Other - The impedance matches one of the values defined by adTA5kPotsPortImpedance that
can not be accurately represented by the values used in this oid. This v…
Enumerationr/w
Enumerated Values:
1loopLengthOther
2loopLengthShort
3loopLengthMedium
4loopLengthLong
 .1.3.6.1.4.1.664.2.753.1.2.1.1.10
adTA5kPotsPortOverTempAlarmEnable
Provisioning for Enable/Disable Over Temperature Alarm which is a port level alarm.
1 = Enable
2 = Disable
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.1.2.1.1.11
adTA5kPotsPortMwiType
Provisioning for the type of Message Waiting Indication for this port to use.
1 = Use Frequency Shift Keying (FSK) to indicate Message Waiting to the phone
2 = Use Neon Voltage to indicate Message Waiting to the phone
Enumerationr/w
Enumerated Values:
1mwiTypeFsk
2mwiTypeNeon
 .1.3.6.1.4.1.664.2.753.1.2.1.1.12
adTA5kPotsPortNeonMwiCadence
Provisioning for the flashing cadence of Neon Message Waiting Indication for this port.
1 = Flash the Neon lamp on or off every 1000ms
2 = Flash the Neon lamp on or off every 500ms
3 = Flash the Neon lamp on or off ever…
Enumerationr/w
Enumerated Values:
1neonMwiCadence1000ms
2neonMwiCadence500ms
3neonMwiCadence250ms
 .1.3.6.1.4.1.664.2.753.1.2.1.1.13
adTA5kPotsPortNeonMwiVoltage
Provisioning for the voltage of Neon Message Waiting Indication for this port.
1 = 85 volts
2 = 90 volts
3 = 100 volts
4 = 110 volts
5 = 120 volts
6 = 130 volts
Enumerationr/w
Enumerated Values:
1neonMwiVoltage85volts
2neonMwiVoltage90volts
3neonMwiVoltage100volts
4neonMwiVoltage110volts
5neonMwiVoltage120volts
6neonMwiVoltage130volts
 .1.3.6.1.4.1.664.2.753.1.2.1.1.14
adTA5kPotsPortVoiceCallJitterBufferDepth
Provisioning for the Jitter Buffer Depth used for Voice Calls in mS
Integer32r/w
Constraints:
range: 0-250
 .1.3.6.1.4.1.664.2.753.1.2.1.1.15
adTA5kPotsPortFaxModemCallJitterBufferDepth
Provisioning for the Jitter Buffer Depth used for Fax Modem Calls in mS
Integer32r/w
Constraints:
range: 0-250
 .1.3.6.1.4.1.664.2.753.1.2.1.1.16
adTA5kPotsPortCircuitIdentifier
The circuit identifier string for the fxs port.
OctetStringr/w
Constraints:
range: 0-40
 .1.3.6.1.4.1.664.2.753.1.2.1.1.17
adTA5kPotsPulseDigitDetectionEnable
This entry is used to enable or disable the pulse dial digit detection for this port.
This entry only applies to fxs ports that are connected to a VoIP service, such as SIP or MGCP.
If set to true, then pulse dial digit…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.664.2.753.1.2.1.1.18

adTA5kPotsCardStatTable

table
.1.3.6.1.4.1.664.2.753.2.1.1 · 1 row entry · 11 columns
Open in standard view 
The POTS Card-level Status table.
adTA5kPotsCardStatEntry entry .1.3.6.1.4.1.664.2.753.2.1.1.1
An entry in the POTS Card-level Status Table.
Indexes
ADTRAN-GENSLOT-MIBadGenSlotInfoIndex
Column Syntax OID
adTA5kPotsCardSelfTestFPGATest
This variable indicates the Self-test FPGA Test Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.1
adTA5kPotsCardSelfTestFlashTest
This variable indicates the Self-test FPGA Flash Test Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.2
adTA5kPotsCardSelfTestLasVegas1Prog
This variable indicates the Self-test Las Vegas #1 Programming Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.3
adTA5kPotsCardSelfTestLasVegas2Prog
This variable indicates the Self-test Las Vegas #2 Programming Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.4
adTA5kPotsCardSelfTestVineticCodecAProg
This variable indicates the Self-test Vinetic Codec A Programming Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.5
adTA5kPotsCardSelfTestVineticCodecBProg
This variable indicates the Self-test Vinetic Codec B Programming Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.6
adTA5kPotsCardSelfTestVineticCodecCProg
This variable indicates the Self-test Vinetic Codec C Programming Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.7
adTA5kPotsCardSelfTestVineticCodecDProg
This variable indicates the Self-test Vinetic Codec D Programming Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.8
adTA5kPotsCardSelfTestVineticCodecEProg
This variable indicates the Self-test Vinetic Codec E Programming Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.9
adTA5kPotsCardSelfTestVineticCodecFProg
This variable indicates the Self-test Vinetic Codec F Programming Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.10
adTA5kPotsCardSelfTestLasVegas3Prog
This variable indicates the Self-test Las Vegas #3 Programming Status of the module.
1 = FAILED
2 = PASSED
Enumeration
Enumerated Values:
1failed
2passed
 .1.3.6.1.4.1.664.2.753.2.1.1.1.11

adTA5kPotsPortStatTable

table
.1.3.6.1.4.1.664.2.753.2.2.1 · 1 row entry · 8 columns
Open in standard view 
The POTS Port-level Status table.
adTA5kPotsPortStatEntry entry .1.3.6.1.4.1.664.2.753.2.2.1.1
An entry in the POTS Port-level Status Table.
Indexes
IF-MIBifIndex
Column Syntax OID
adTA5kPotsPortStatLineMode
This item indicates which mode the port is currently operating in.
1 = Loop Start
2 = Ground Start
Enumeration
Enumerated Values:
1loopStart
2groundStart
 .1.3.6.1.4.1.664.2.753.2.2.1.1.1
adTA5kPotsPortStatLineActive
This item indicates whether the port is currently active or not.
1 = Active
2 = Not Active
Enumeration
Enumerated Values:
1active
2inActive
 .1.3.6.1.4.1.664.2.753.2.2.1.1.2
adTA5kPotsPortStatLineCompression
This item indicates which type of compression is being used.
1 = G.711
2 = G.726
Enumeration
Enumerated Values:
1g711
2g726
 .1.3.6.1.4.1.664.2.753.2.2.1.1.3
adTA5kPotsPortStatLoopFeed
This item indicates the loop feed status of the port.
1 = Loop Current Feed
2 = Reverse Loop Current Feed
3 = OSI
4 = Tip Ground
5 = Ringing
6 = Power Down
Enumeration
Enumerated Values:
1lcf
2rlcf
3osi
4tipGround
5ringing
6powerDown
 .1.3.6.1.4.1.664.2.753.2.2.1.1.4
adTA5kPotsPortStatLoopState
This item indicates the loop state of the port.
1 = Loop Open
2 = Loop Closed
3 = Ring Ground
Enumeration
Enumerated Values:
1loopOpen
2loopClosed
3ringGround
 .1.3.6.1.4.1.664.2.753.2.2.1.1.5
adTA5kPotsPortStatTestActive
This item indicates whether a test is active on the port or not.
1 = Active
2 = Not Active
Enumeration
Enumerated Values:
1yes
2no
 .1.3.6.1.4.1.664.2.753.2.2.1.1.6
adTA5kPotsPortStatServiceState
POTS port service state-
1 = In Service
2 = Out Of Service - Unassigned
3 = Out Of Service - Maintenance
Enumeration
Enumerated Values:
1is
2oosUAS
3oosMA
 .1.3.6.1.4.1.664.2.753.2.2.1.1.7
adTA5kPotsPortMwiStatus
POTS MWI Status -
1 = Status Unknown
2 = Indicator OFF
3 = Indicator ON
4 = Indicator OFF (forced)
5 = Indicator ON (forced)
Note: unknown will always be returned in FXS Signaling mode.
This is because a FXS Signaling p…
Enumeration
Enumerated Values:
1unknown
2indicatorOff
3indicatorOn
4indicatorOffForced
5indicatorOnForced
 .1.3.6.1.4.1.664.2.753.2.2.1.1.8

adTA5kPotscardStatisticsTable

table
.1.3.6.1.4.1.664.2.753.2.3.1.1 · 1 row entry · 5 columns
Open in standard view 
The POTS card-level Statistics table.
adTA5kPotscardStatisticsEntry entry .1.3.6.1.4.1.664.2.753.2.3.1.1.1
An entry in the POTS card-level Statistics Table.
Indexes
ADTRAN-GENSLOT-MIBadGenSlotInfoIndex
Column Syntax OID
adTA5kPotsCardRXEthernetPkts
This will give the number of Received ethernet packets
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.2.753.2.3.1.1.1.1
adTA5kPotsCardTXEthernetPkts
This will give the number of transmitted ethernet packets
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.2.753.2.3.1.1.1.2
adTA5kPotsCardVoiceGatewayTimeouts
This will give the voice gateway timeouts
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.2.753.2.3.1.1.1.3
adTA5kPotsCardClearStatistics
This will clear all the card level statistics when set to 1. A get will always return a 1.
1 = Clear
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.2.753.2.3.1.1.1.4
adTA5kPotsPortClearStatistics
This will clear all Port level statistics when set to 1. A get will always return a 1.
1 = Clear
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.2.753.2.3.1.1.1.5

adTA5kPotsPortStatisticsTable

table
.1.3.6.1.4.1.664.2.753.2.3.2.1 · 1 row entry · 4 columns
Open in standard view 
The POTS port-level Statistics table.
adTA5kPotsPortStatisticsEntry entry .1.3.6.1.4.1.664.2.753.2.3.2.1.1
An entry in the POTS port-level Statistics Table.
Indexes
IF-MIBifIndex
Column Syntax OID
adTA5kPotsPortRXVoicePkts
This will give the number of Received Voice packets
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.2.753.2.3.2.1.1.1
adTA5kPotsPortTXVoicePkts
This will give the number of transmitted Voice packets
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.2.753.2.3.2.1.1.2
adTA5kPotsPortRXSignalPkts
This will give the number of Received signal packets
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.2.753.2.3.2.1.1.3
adTA5kPotsPortTXSignalPkts
This will give the number of transmitted signal packets
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.664.2.753.2.3.2.1.1.4

adTA5kPotsCardTestTable

table
.1.3.6.1.4.1.664.2.753.3.1.1 · 1 row entry · 2 columns
Open in standard view 
The POTS Card-level Test table.
adTA5kPotsCardTestEntry entry .1.3.6.1.4.1.664.2.753.3.1.1.1
An entry in the POTS Card-level Test Table.
Indexes
ADTRAN-GENSLOT-MIBadGenSlotInfoIndex
Column Syntax OID
adTA5kPotsCardTestLpbkPotsLine
This item enables/disables the POTS line loopback toward the network.
1 = Enable
2 = Disable
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.3.1.1.1.1
adTA5kPotsCardTestLpbkPotsPayload
This item enables/disables the POTS payload loopback toward
the network.
1 = Enable
2 = Disable
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.3.1.1.1.2

adTA5kPotsLineTestTable

table
.1.3.6.1.4.1.664.2.753.3.2.1 · 1 row entry · 10 columns
Open in standard view 
The POTS Line-level Test table.
adTA5kPotsLineTestEntry entry .1.3.6.1.4.1.664.2.753.3.2.1.1
An entry in the POTS Line-level Test Table.
Indexes
IF-MIBifIndex
Column Syntax OID
adTA5kPotsLineTest1004HzTone
This item controls the generation of a 1004 Hz test tone
from the POTS interface.
1 = To Loop
2 = To Network
3 = Disable
Enumerationr/w
Enumerated Values:
1toLoop
2toNetwork
3disable
 .1.3.6.1.4.1.664.2.753.3.2.1.1.1
adTA5kPotsLineTestRingCadence
This item enables/disables the ring cadence test on the POTS interface.
1 = Enable
2 = Disable
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.3.2.1.1.2
adTA5kPotsLineTestLoopState
This item controls the loop state test on the POTS interface.
1 = Disable
2 = Active High
3 = Active Low
4 = Reverse Active High
5 = Reverse Active Low
6 = Power Down Active
7 = Power Down Resistive
8 = Tip Ground
9 = A…
Enumerationr/w
Enumerated Values:
1disable
2activeHigh
3activeLow
4reverseActiveHigh
5reverseActiveLow
6powerDownActive
7powerDownResistive
8tipGround
9activeTest
10tipOpen
 .1.3.6.1.4.1.664.2.753.3.2.1.1.3
adTA5kPotsLineClearTest
This will clear all Port Line Tests. The get will always return 1.
1 = Clear
Enumerationr/w
Enumerated Values:
1clear
 .1.3.6.1.4.1.664.2.753.3.2.1.1.4
adTA5kPotsLineTestWarbleTone
This will enable or disable a warble tone as defined by the oids
adTA5kPotsLineTestWarbleToneFreq1, adTA5kPotsLineTestWarbleToneFreq2,
and adTA5kPotsLineTestWarbleToneCadence.
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.664.2.753.3.2.1.1.5
adTA5kPotsLineTestWarbleToneFreq1
The first alternating frequency used in the warble tone.
Enumerationr/w
Enumerated Values:
1silence
2tone1004hz
3tone1400hz
4tone2040hz
 .1.3.6.1.4.1.664.2.753.3.2.1.1.6
adTA5kPotsLineTestWarbleToneFreq2
The second alternating frequency used in the warble tone.
Enumerationr/w
Enumerated Values:
1silence
2tone1004hz
3tone1400hz
4tone2040hz
 .1.3.6.1.4.1.664.2.753.3.2.1.1.7
adTA5kPotsLineTestWarbleToneCadence
The amount of time in ms that one frequency in the warble tone is played before
alternating to the the other frequency.
Enumerationr/w
Enumerated Values:
1time100ms
2time250ms
3time500ms
 .1.3.6.1.4.1.664.2.753.3.2.1.1.8
adTA5kPotsPortForceMwiOffEvent
A set command will force the Message Waiting Indicator for the port to turn OFF.
Get has no meaning and will always return indicatorOff(1).
This provides a means for MWI events to be forced out to the fxs port locally.
…
Enumerationr/w
Enumerated Values:
1indicatorOff
 .1.3.6.1.4.1.664.2.753.3.2.1.1.9
adTA5kPotsPortForceMwiOnEvent
A set command will force the Message Waiting Indicator for the port to turn ON.
Get has no meaning and will always return indicatorOn(1).
This provides a means for MWI events to be forced out to the fxs port locally.
Af…
Enumerationr/w
Enumerated Values:
1indicatorOn
 .1.3.6.1.4.1.664.2.753.3.2.1.1.10