SN-MSPS-SCX-MIB Table View

A table to control device features like egress traffic control,
stats collection, etc. either for the entire switch or for each
interface in the switch.

snMspsConfigCtrlEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1

An entry appears in this table for each interface in the system.

In addition to that an entry with index '0' is created in this
table by default.

If 'snMspsConfigCtrlStatus' of the entry '0' is…

Indexes

snMspsConfigCtrlIndex

Column	Syntax	OID
snMspsConfigCtrlIndex Interface index of the port for which the configuration in this entry applies. If any configuration is made in this table for the index '0', that configuration will be considered as global configuration …	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1.1
snMspsConfigCtrlEgressStatus Controls the transmission of egress traffic over this interface. This value for entry '0' controls the egress traffic over all interfaces.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1.2
snMspsConfigCtrlStatsCollection Enables or disables statistics collection for this interface. This value for entry '0' controls the stats collection for all interfaces.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1.3
snMspsConfigCtrlStatus Speficies the validity of the entry. If the 'Config Control Status' for entry '0' is made 'valid', then global control is chosen in the system. It signifies that the values against entry '0' is applicable…	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.4329.20.1.1.1.1.1.2.1.4

A table to control the rate limiting parameters 
either for the entire switch or for each physical and port-channel
interface in the switch.

snMspsConfigRateCtrlEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1

An entry appears in this table for each physical and port-channel
interface in the switch.

Indexes

snMspsConfigRateCtrlIndex

Column	Syntax	OID
snMspsConfigRateCtrlIndex The interface index for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.1
snMspsConfigRateCtrlDLFLimitValue Allows to configure the limiting value for the maximum number of dlf data that can be transmitted per second over this interface. The unit of data is given by snMspsConfigRateCtrlUnit object. Setting this object to the …	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.2
snMspsConfigRateCtrlBCASTLimitValue Allows to configure the limiting value for the maximum number of broadcast data that can be transmitted per second over this interface. The unit of data is given by snMspsConfigRateCtrlUnit object. Setting this object …	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.3
snMspsConfigRateCtrlMCASTLimitValue Allows to configure the limiting value for the maximum number of multicast data that can be transmitted per second over this interface. The unit of data is given by snMspsConfigRateCtrlUnit object. Setting this object …	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.4
snMspsConfigRateCtrlPortRateLimit Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, th…	Integer32r/w Constraints: range: 0-80000000	.1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.5
snMspsConfigRateCtrlPortBurstSize Configures interface Burst Pkt Rate. (Packet Burst that can be transferred on a port at a particular second) This object's value will take effect on the interface speed. Based on the operating speed of th…	Integer32r/w Constraints: range: 0-80000000	.1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.6
snMspsConfigRateCtrlUCASTLimitValue Allows to configure the limiting value for the maximum number of unicast data that can be transmitted per second over this interface. The unit of data is given by snMspsConfigRateCtrlUnit object. Setting this object to…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.3.1.7

A table to control the rate limiting parameters 
either for the entire switch or for each physical and port-channel
interface in the switch. Chip-Dependent!

snMspsConfigAclRateCtrlEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1

An entry appears in this table for each physical and port-channel
interface in the switch.

Indexes

snMspsConfigAclRateCtrlIndex

Column	Syntax	OID
snMspsConfigAclRateCtrlIndex The interface index for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.1
snMspsConfigAclRateCtrlDLFLimitValue Allows to configure the limiting value for the maximum number of dlf packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for Destination lookup f…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.2
snMspsConfigAclRateCtrlBCASTLimitValue Allows to configure the limiting value for the maximum number of broadcast packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for Broadcast pac…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.3
snMspsConfigAclRateCtrlMCASTLimitValue Allows to configure the limiting value for the maximum number of multicast packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for Multicast pac…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.4
snMspsConfigAclRateCtrlPortRateLimit Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, th…	Integer32r/w Constraints: range: 0-80000000	.1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.5
snMspsConfigAclRateCtrlPortBurstSize Configures interface Burst Pkt Rate. (Packet Burst that can be transferred on a port at a particular second) This object's value will take effect on the interface speed. Based on the operating speed of th…	Integer32r/w Constraints: range: 0-80000000	.1.3.6.1.4.1.4329.20.1.1.1.1.1.4.1.6

A table to control the port specific parameters of the device like speed,
duplex mode, etc.

snMspsConfigPortCtrlEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1

An entry appears in this table for each interface in the system.

Index to the table is the interface index of the port.

Indexes

snMspsConfigPortCtrlIndex

Column	Syntax	OID
snMspsConfigPortCtrlIndex Interface index of the port for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.1
snMspsConfigPortCtrlMode Speficies the mode in which the speed, duplex modes and flow control of the interface is determined. If set as 'auto', the hardware senses speed and negotiates with the port on the other end of the link …	Enumerationr/w Enumerated Values: 1 auto 2 noNegotiation	.1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.2
snMspsConfigPortCtrlDuplex Configures interface data transfer mode as full-duplex or half-duplex. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value f…	Enumerationr/w Enumerated Values: 1 full 2 half	.1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.3
snMspsConfigPortCtrlSpeed Configures interface speed. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its pe…	Enumerationr/w Enumerated Values: 1 tenMBPS 2 hundredMBPS 3 oneGB 4 tenGB	.1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.4
snMspsConfigPortCtrlFlowControl Enables / disables flow control for the interface. This object be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negot…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.5
snMspsConfigPortCtrlRenegotiate When configured as 'true', restarts autonegotiation on the interface. Once autonegotiation is restarted, the value of this object reverts to 'false'.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.6
snMspsConfigPortCtrlMaxMacAddr Specifies the maximum number of new MAC addresses that can be learnt over the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.7
snMspsConfigPortCtrlMaxMacAction Specifies the action to be taken when the maximum number of new MAC addresses that can be learnt over the interface is exceeded. If the action is 'drop', the packet with new mac address will be dropped o…	Enumerationr/w Enumerated Values: 1 drop 2 purgeLRU	.1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.8
snMspsConfigPortHOLBlockPrevention Enables or disables Head-Of-Line Blocking prevention on a port.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.4329.20.1.1.1.1.1.5.1.9

A table to control mirroring features for each interface 
in the switch.
          
Parameters in this table are valid only when the 
'snMspsConfigMirrorStatus' for the switch is not 'disabled'.

snMspsConfigMirrorCtrlEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1

An entry appears in this table for each interface
in the system.

Indexes

snMspsConfigMirrorCtrlIndex

Column	Syntax	OID
snMspsConfigMirrorCtrlIndex The interface index of the port for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1.1
snMspsConfigMirrorCtrlIngressMirroring Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1.2
snMspsConfigMirrorCtrlEgressMirroring Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1.3
snMspsConfigMirrorCtrlStatus Specifies the validity of the entry.	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.3.1.4

This Table is used to configure advanced mirroring features like
- Port Based Mirroring:
- flow based mirroring
- vlan based mirroring
          
     Following are the configuration details for Port based mirroring:
         To configure source ports in a session
        - snMspsConfigMirrorCtrlExtnMirrType - is set to portBased
        - snMspsConfigMirrorCtrlExtnSrcTable - should be used to configure list
                                      of source ports to be mirrored 
                                      in a session
        - snMspsConfigMirrorCtrlExtnSrcId  - represents the source port. 
                                    The port Id to be mirrored 
                                    should be given here.
        - snMspsConfigMirrorCtrlExtnSrcCfg - this object is used to 
                                    add/remove a port in the 
                                    source port list 
          
        Example
        To create a session 1 with source ports 5,6 following 
        sequence of configuration should be followed
        For table snMspsConfigMirrorCtrlExtnTable
        snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
        snMspsConfigMirrorCtrlExtnMirrType = portBased
          
        For table snMspsConfigMirrorCtrlExtnSrcTable
        snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
        snMspsConfigMirrorCtrlExtnSrcId  = 5 as index
        snMspsConfigMirrorCtrlExtnSrcCfg = add
        snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
        snMspsConfigMirrorCtrlExtnSrcId  = 6 as index
        snMspsConfigMirrorCtrlExtnSrcCfg = add
                       
        To configure destination ports in a session
         - snMspsConfigMirrorCtrlExtnDestinationTable - should be used to 
                                               configure list of 
                                               destination ports to be 
                                               mirrored in a session
             - snMspsConfigMirrorCtrlExtnDestination  - represents the 
                                               destination port. The 
                                               port Id to which packets 
                                               should be mirrored should
                                               be given here.
             - snMspsConfigMirrorCtrlExtnDestCfg - this object is used to 
                                          add/remove a port in the 
                                          source port list. 
             Example
             To create a session 1 with destination port 10,11 following
             sequence of configuration should be followed
             For table snMspsConfigMirrorCtrlExtnTable
             snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
             snMspsConfigMirrorCtrlExtnMirrType = portBased
          
             For table snMspsConfigMirrorCtrlExtnDestinationTable
             snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
             snMspsConfigMirrorCtrlExtnDestination  = 10 as index
             snMspsConfigMirrorCtrlExtnDestCfg = add
             snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
             snMspsConfigMirrorCtrlExtnDestination  = 11 as index
             snMspsConfigMirrorCtrlExtnDestCfg = add
          
        To Activate a session
         - snMspsConfigMirrorCtrlExtnStatus - should be used to 
                                     activate/deactivate mirroring for a
                                     session
             Example
             To enable mirroring for a session following sequence of 
             configuration should be followed        
             For table snMspsConfigMirrorCtrlExtnTable
             snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
             snMspsConfigMirrorCtrlExtnStatus = active
          
         Above configurations applies to flow based mirroring also, the 
         snMspsConfigMirrorCtrlExtnSrcId used above for configuratin ports 
         should be used to configure flow Id
                   
        To enable remote monitoring of sources for a session
         - snMspsConfigMirrorCtrlExtnRSpanStatus - should be used to 
                                          enable/disable remote 
                                          monitoring for a session 
                                          it can be used to set a 
                                          session as source rspan 
                                          session which implies source 
                                          entities for this session are 
                                          monitored remotely or can be 
                                          used to set a session 
                                          as destination rspan session 
                                          which implies that mirrored 
                                          data is received for this 
                                          session should be forwarded to 
                                          destination entities of this 
                                          session
         - snMspsConfigMirrorCtrlExtnRSpanVlanId - it is the vlan id which is 
                                          reserved in the network to 
                                          carry Mirrored data,if the 
                                          session is configured as 
                                          source rspan session then data 
                                          mirrored for the source 
                                          entities will be forwarded on 
                                          this vlan if the session is 
                                          configured as destination 
                                          rspan session then data 
                                          received on this vlan will be 
                                          forwarded to the destination 
                                          entities of this session
          
     Following are the configuration details for configurating Vlan 
     based mirroring:
         To configure vlans as source for a session
        - snMspsConfigMirrorCtrlExtnMirrType - is set to vlanBased
        - snMspsConfigMirrorCtrlExtnSrcVlanTable - should be used to configure 
                                          list of source vlans to be 
                                          mirrored in a session
          - snMspsConfigMirrorCtrlExtnSrcVlanId  - represents a source vlan. The 
                                          vlan to be mirrored should be 
                                          given here.
          - snMspsConfigMirrorCtrlExtnSrcVlanCfg - this object is used to 
                                          add/remove a vlan in the 
                                          source vlan list 
             Example
             To create a session 1 with source list as vlan 5,6 
             belonging to context 1 following sequence of configuration
             should be followed
             For table snMspsConfigMirrorCtrlExtnTable
             snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
             snMspsConfigMirrorCtrlExtnMirrType = vlanBased
          
             For table snMspsConfigMirrorCtrlExtnSrcVlanTable
             snMspsConfigMirrorCtrlExtnSrcVlanContext = 1 as index
             snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
             snMspsConfigMirrorCtrlExtnSrcVlanId  = 5 as index
             snMspsConfigMirrorCtrlExtnSrcVlanCfg = add
             snMspsConfigMirrorCtrlExtnSrcVlanContext = 1 as index
             snMspsConfigMirrorCtrlExtnSessionIndex = 1 as index
             snMspsConfigMirrorCtrlExtnSrcVlanId  = 6 as index
             snMspsConfigMirrorCtrlExtnSrcVlanCfg = add
                       
Entries for this table can be configured only when snMspsConfigMirrorStatus 
is set to enabled.
Configurations done through 'snMspsConfigMirrorCtrlTable' will change the 
following for the first session on this table:
     - Mirroring type will be changed to port-based
     - Mode and Source entities will be overwritten 
       with the values configured through 'snMspsConfigMirrorCtrlTable'
     - Destination entities will be overwritten 
       with the value configured through 'snMspsConfigMirrorToPort' object

snMspsConfigMirrorCtrlExtnEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1

An entry appears in this table for each session
in the system.

Indexes

snMspsConfigMirrorCtrlExtnSessionIndex

Column	Syntax	OID
snMspsConfigMirrorCtrlExtnSessionIndex The index of the mirroring session for which the configuration in this entry applies.	Integer32 Constraints: range: 1-20	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.1
snMspsConfigMirrorCtrlExtnMirrType This object tells the type of mirroring this session supports. This object needs to be set before doing any configuration for a mirroring session	Enumerationr/w Enumerated Values: 1 portBased 2 mac-flowBased 3 vlanBased 4 invalid 5 ip-flowBased	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.2
snMspsConfigMirrorCtrlExtnRSpanStatus This object indicates session is enabled or disabled for Remote monitoring. If set as 'source-rspan-vlanid' indicates that the session is enabled for Remote monitoring and the source entities for this session will be…	Enumerationr/w Enumerated Values: 1 sourceRSpanVlan 2 destinationRSpanVlan 3 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.3
snMspsConfigMirrorCtrlExtnRSpanVlanId Vlan Id used for Remote monitoring for this session. If snMspsConfigMirrorCtrlExtnRSpanStatus is set to disabled, then this object will have an invalid value (zero)	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.4
snMspsConfigMirrorCtrlExtnRSpanContext Specifies the Context Id to which the RSpan Vlan belongs. Value '0' mean this object is not considered for this mirroring session.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.5
snMspsConfigMirrorCtrlExtnStatus This object indicates the status of the entry. The entry can be made active only if snMspsConfigMirrorCtrlExtnMirrType is configured and source and destination entries for this sesion is also configured	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.6
snMspsConfigMirrorCtrlExtnHardwareIndex Specifies the Hardware Index associated with this mirroring session. Value '0' mean this object is not applicable for this mirroring session.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.6.1.7

A table to configure list of source entities for mirroring sessions

snMspsConfigMirrorCtrlExtnSrcEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.7.1

An entry appears in this table for each mirroring session.

Indexes

snMspsConfigMirrorCtrlExtnSessionIndex snMspsConfigMirrorCtrlExtnSrcId

Column	Syntax	OID
snMspsConfigMirrorCtrlExtnSrcId Specifies the source id which participates in a mirroring session. For Port based mirroring this object can be port IfIndex. To mirror Tunnel and Trunk ports the same Id can be used for specifying Tunnel/Trunk Id. For …	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.7.1.1
snMspsConfigMirrorCtrlExtnSrcCfg This object is used to create/delete a source entry for a session.	Enumerationr/w Enumerated Values: 1 add 2 delete	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.7.1.2
snMspsConfigMirrorCtrlExtnSrcMode Provides control to set the mode of mirroring. It can be ingerss,Egress or Both.	Enumerationr/w Enumerated Values: 1 ingress 2 egress 3 both	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.7.1.3

A table to configure list of vlan source entities for mirroring sessions

snMspsConfigMirrorCtrlExtnSrcVlanEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1

An entry appears in this table for each mirroring session.

Indexes

snMspsConfigMirrorCtrlExtnSessionIndex snMspsConfigMirrorCtrlExtnSrcVlanContext snMspsConfigMirrorCtrlExtnSrcVlanId

Column	Syntax	OID
snMspsConfigMirrorCtrlExtnSrcVlanContext Specifies the Context Id to which the source entity belongs, this is used in case of specifying vlan as source. Value '-1' mean this object is not considered for this mirroring session.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1.1
snMspsConfigMirrorCtrlExtnSrcVlanId Specifies the Vlan id which participates in a mirroring session.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1.2
snMspsConfigMirrorCtrlExtnSrcVlanCfg This object is used to create/delete a vlan entry for a session.	Enumerationr/w Enumerated Values: 1 add 2 delete	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1.3
snMspsConfigMirrorCtrlExtnSrcVlanMode Provides control to set the mode of mirroring. It can be ingerss,Egress or Both.	Enumerationr/w Enumerated Values: 1 ingress 2 egress 3 both	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.8.1.4

A table to configure list of destination entities

snMspsConfigMirrorCtrlExtnDestinationEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.6.9.1

An entry appears in this table for each destination entity
in a mirroring session.

Indexes

snMspsConfigMirrorCtrlExtnSessionIndex snMspsConfigMirrorCtrlExtnDestination

Column	Syntax	OID
snMspsConfigMirrorCtrlExtnDestination Specifies the destination port id which participates in a mirroring session.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.9.1.1
snMspsConfigMirrorCtrlExtnDestCfg This object is used to create/delete a destination entry for a session.	Enumerationr/w Enumerated Values: 1 add 2 delete	.1.3.6.1.4.1.4329.20.1.1.1.1.1.6.9.1.2

A table to configure L2 filter rules in the system.

snMspsConfigL2FilterEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1

Each entry in this table is a L2 filter rule.

Index to the table is the L2 filter number.

Indexes

snMspsConfigL2FilterNo

Column	Syntax	OID
snMspsConfigL2FilterNo L2 Filter rule number.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.1
snMspsConfigL2FilterPriority The priority of the L2 filter can be used to decide which filter rule is applicable when --> the packet matches with more than one filter rules --> All the filter rules result in 'allow'ing the packet …	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.2
snMspsConfigL2FilterEtherType The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '0'. When this object is SET with the default value, frames are not matched for the value in th…	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.3
snMspsConfigL2FilterProtocolType Specifies the non IP protocol type to be filtered. aarp | amber | dec-spanning | decnet-iv | diagnostic | dsm |etype-6000 | etype-8042 | lat | lavc-sca | mop-console | mop-dump | msdos | mumps | netbios | vines-echo …	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.4
snMspsConfigL2FilterDstMacAddr Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero which means dont care condition ie) any Dst Mac Address .	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.5
snMspsConfigL2FilterSrcMacAddr Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero which means dont care condition ie) any Src Mac address	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.6
snMspsConfigL2FilterVlanId Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. A value of '0' means, this object is unused. Configuring this value is not allowed.	Integer32r/w Constraints: range: 0-4094	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.7
snMspsConfigL2FilterInPortList Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. If the In port list is '0', the filter rule is applicable for the incoming packets on all ports. Even th…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.8
snMspsConfigL2FilterAction Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.	Enumerationr/w Enumerated Values: 1 allow 2 drop	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.9
snMspsConfigL2FilterMatchCount Number of times this filter is matched.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.10
snMspsConfigL2FilterStatus This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.11
snMspsConfigL2FilterOutPortList Specifies the complete set of ports over which this filter is applied for packets egress at Ports in this list. If the Out port list is '0', the filter rule is applicable for the outgoing packets on all ports. Even th…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.12
snMspsConfigL2FilterDirection Specifies the direction of this filter to be applied. By Default the filter will be applied on ingress direction. When the direction of this filter is 'in', It is applied on specified ports of the snMspsConfigL2FilterIn…	Enumerationr/w Enumerated Values: 1 in 2 out	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.1.1.13

A table to L4 Switching rules in the system.

snMspsConfigL4SwitchingFilterEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1

Each entry in this table is a L4 Switching rule.
Index to the table is L4 filter number.

Indexes

snMspsConfigL4SwitchingFilterNo

Column	Syntax	OID
snMspsConfigL4SwitchingFilterNo L4 Switching Filter rule number.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.1
snMspsConfigL4SwitchingProtocol The type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can be anything and it will not be checked to decide the action.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.2
snMspsConfigL4SwitchingPortNo The Layer 4 port no. Please note these ports are the TCP / UDP ports.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.3
snMspsConfigL4SwitchingCopyToPort This object is Port to which the packet would be switched	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.4
snMspsConfigL4SwitchingFilterStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.2.1.5

A table to configure IP authorized managers in the system.

snMspsConfigIpAuthMgrEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1

IP Authorized managers, which restricts configuration from specific
workstations only, provides additional security. Each entry in this
table represents rules for particular IP authorized manager.

Indexes

snMspsConfigIpAuthMgrIpAddr snMspsConfigIpAuthMgrIpMask

Column	Syntax	OID
snMspsConfigIpAuthMgrIpAddr Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.1
snMspsConfigIpAuthMgrIpMask Specifies the IP address mask to be applied on snMspsConfigIpAuthMgrIpAddr. Value 0.0.0.0 indicates mask for 'Any Manager'.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.2
snMspsConfigIpAuthMgrPortList Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.3
snMspsConfigIpAuthMgrVlanList Specifies the Vlan's in which the IP authorized manager can reside. By default the manager is allowed to reside in any vlan. If a set of vlans are configured in the 'VlanList', the manager can reside onl…	OctetStringr/w	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.4
snMspsConfigIpAuthMgrOOBPort Specifies whether the authorized manager can access the switch through OOB Port By default the manager is denied access to reside on OOB Interface	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.5
snMspsConfigIpAuthMgrAllowedServices Specifies the allowed services through which the authorized manager can access the switch. This object takes bit mask values. The services represented by each bit position is as given below: With bi…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.6
snMspsConfigIpAuthMgrRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.7
snMspsConfigIpAuthMgrCreationOrder Specifies creation order of the rules	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.3.1.8

A table to configure Ipvx(ipv4 and ipv6) authorized managers in the system.

snMspsConfigIpvxAuthMgrEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1

Ipvx Authorized managers, which restricts configuration from specific
workstations only, provides additional security. Each entry in this
table represents rules for particular Ipvx authorized manager.

Indexes

snMspsConfigIpvxAuthMgrAddrType snMspsConfigIpvxAuthMgrAddr snMspsConfigIpvxAuthMgrAddrLen

Column	Syntax	OID
snMspsConfigIpvxAuthMgrAddrType The IP address type of SnMspsConfigIpvxAuthMgrEntry. This value determines the type for snMspsConfigIpvxAuthMgrAddr and snMspsConfigIpvxAuthMgrAddrLen. ipv4(1) and ipv6(2) are the only two values supporte…	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.1
snMspsConfigIpvxAuthMgrAddr Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 or :: indicates 'Any Manager'.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.2
snMspsConfigIpvxAuthMgrAddrLen Indicates the number of leading one bits that form the mask to be logical-ANDed with the snMspsConfigIpvxAuthMgrAddr before being compared to the value in the snMspsConfigIpvxAuthMgrAddr field. The values…	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.3
snMspsConfigIpvxAuthMgrPortList Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of p…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.4
snMspsConfigIpvxAuthMgrVlanList Specifies the Vlan's in which the IP authorized manager can reside. By default the manager is allowed to reside in any vlan. If a set of vlans are configured in the 'VlanList', the manager can reside only…	OctetStringr/w	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.5
snMspsConfigIpvxAuthMgrOOBPort Specifies whether the authorized manager can access the switch through OOB Port By default the manager is denied access to reside on OOB Interface	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.6
snMspsConfigIpvxAuthMgrAllowedServices Specifies the allowed services through which the authorized manager can access the switch. This object takes bit mask values. The services represented by each bit position is as given below: With bit 0 be…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.7
snMspsConfigIpvxAuthMgrCreationOrder Specifies creation order of the rules	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.8
snMspsConfigIpvxAuthMgrRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.1.7.10.1.9

A table to control the port specific parameters of the device like speed,
duplex mode, etc.

snMspsConfigPortCtrlConfigurationEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1

An entry appears in this table for each interface in the system.

Index to the table is the interface index of the port.

Indexes

snMspsConfigPortCtrlConfigurationIndex

Column	Syntax	OID
snMspsConfigPortCtrlConfigurationIndex Interface index of the port for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.1
snMspsConfigPortCtrlConfigurationMode Speficies the mode in which the speed, duplex modes and flow control of the interface is determined. If set as 'auto', the hardware senses speed and negotiates with the port on the other end of the link …	Enumerationr/w Enumerated Values: 1 auto 2 noNegotiation	.1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.2
snMspsConfigPortCtrlConfigurationDuplex Configures interface data transfer mode as full-duplex or half-duplex. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value f…	Enumerationr/w Enumerated Values: 1 full 2 half	.1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.3
snMspsConfigPortCtrlConfigurationSpeed Configures interface speed. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its pe…	Enumerationr/w Enumerated Values: 1 tenMBPS 2 hundredMBPS 3 oneGB 4 tenGB	.1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.4
snMspsConfigPortCtrlConfigurationFlowControl Enables / disables flow control for the interface. This object be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negot…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.5
snMspsConfigPortCtrlConfigurationRenegotiate When configured as 'true', restarts autonegotiation on the interface. Once autonegotiation is restarted, the value of this object reverts to 'false'. The current value of this MIB object re…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.6
snMspsConfigPortCtrlConfigurationMaxMacAddr Specifies the maximum number of new MAC addresses that can be learnt over the interface. The current value of this MIB object represents only configuration state. The real state of this port-specific p…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.7
snMspsConfigPortCtrlConfigurationMaxMacAction Specifies the action to be taken when the maximum number of new MAC addresses that can be learnt over the interface is exceeded. If the action is 'drop', the packet with new mac address will be dropped o…	Enumerationr/w Enumerated Values: 1 drop 2 purgeLRU	.1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.8
snMspsConfigPortCtrlConfigurationHOLBlockPrevention Enables or disables Head-Of-Line Blocking prevention on a port. The current value of this MIB object represents only configuration state. The real state of this port-specific parameter may be different (…	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.4329.20.1.1.1.1.1.12.1.9

A table to control the rate limiting parameters 
either for the entire switch or for each physical and port-channel
interface in the switch.

snMspsConfigRateCtrlLimitEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.15.1

An entry appears in this table for each physical and port-channel
interface in the switch.

Indexes

snMspsConfigRateCtrlLimitIndex

Column	Syntax	OID
snMspsConfigRateCtrlLimitIndex The interface index for which the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.15.1.1
snMspsConfigRateCtrlLimitValue Allows to configure the limiting value for the maximum number of dlf, multicast and broadcast data that can be transmitted per second over this interface. The unit of data is given by snMspsConfigRateCtrlUnit object. …	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.15.1.2

This table contains the login usernames and privileges, which are currently created.

snMspsLoginUsersTableEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.65.5.1

user table entry

Indexes

snMspsLoginUserName

Column	Syntax	OID
snMspsLoginUserName User Name which is used as index of the snMspsLoginUserTable.	RFC1213-MIBDisplayString Constraints: range: 1-255	.1.3.6.1.4.1.4329.20.1.1.1.1.1.65.5.1.1
snMspsLoginUserPrivilege User Privilege	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.65.5.1.2
snMspsLoginUserRemoteAccess Remote Access Filter . Value 0 means its allowed to access.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.1.65.5.1.3

A table to display and to control the configuration pack backup.

snMspsConfigBackupEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1

An entry appears in this table for each configuration pack.

Indexes

snMspsConfigBackupIndex

Column	Syntax	OID
snMspsConfigBackupIndex The auxiliary number of corresponding entry representing settings of each config backup.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.1
snMspsConfigBackupFileName The file name of configuration backup.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.4
snMspsConfigBackupFileSize The file size in kilobytes of configuration backup.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.7
snMspsConfigBackupOperation This is a trigger and status variable. Write access using restore(1), initiates restore of corresponding backup configuration. After the operation is completed, the object will return idle(0). Write access using other …	Enumerationr/w Enumerated Values: 0 idle 1 restore 2 in-progress 3 not-enough-storage 4 error	.1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.50
snMspsConfigBackupStatus This is a control variable. It controls the instantiation of a conceptual row in snMspsConfigBackupTable. The new row cannot be activated as long as snMspsConfigBackupFileName is not set.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.1.100.10.1.100

This table contains version informations of all hardware 
(basic device and extension cards), which are currently 
	      available on the device.

snMspsGeneralHwVersionEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1

An entry appears in this table for each hardware
in the system, which has a MLFB number.

Indexes

snMspsGeneralHwVersionTableIndex

Column	Syntax	OID
snMspsGeneralHwVersionTableIndex This index correlates with entPhysicalIndex from entPhysicalTable (ENTITY-MIB).	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.1
snMspsGeneralHwType The type of hardware in readable format.	RFC1213-MIBDisplayString Constraints: range: 0-32	.1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.2
snMspsGeneralHwName The name of hardware in readable format.	RFC1213-MIBDisplayString Constraints: range: 0-32	.1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.3
snMspsGeneralHwRevision The number of hardware revision.	RFC1213-MIBDisplayString Constraints: range: 1-32	.1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.4
snMspsGeneralHwOrderId Order ID of hardware.	SnMspsOrderNumber Type Constraints: range: 1 range: 5..32 Description: The format of type identification / order numbers of Siemens MSPS products.	.1.3.6.1.4.1.4329.20.1.1.1.1.2.20.1.5

This table contains version informations of software, which is currently 
running on relevant hardware (basic device and extension cards).

snMspsGeneralSwVersionEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1

An entry appears in this table for each software
running in the system. Since the same kinds of software
could run on different hardware, which is available
on the device, the index from 'snMspsGeneralHwVersionTabl…

Indexes

snMspsGeneralHwVersionTableIndex snMspsGeneralSwVersionTableIndex

Column	Syntax	OID
snMspsGeneralSwVersionTableIndex The numerical index of software, which is available on relevant hardware.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.1
snMspsGeneralSwType The type of software in readable format.	RFC1213-MIBDisplayString Constraints: range: 0-32	.1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.2
snMspsGeneralSwRevision The number of software revision.	SnMspsVersionNumber Type Constraints: range: 5..32 Description: The version format of Siemens MSPS in a simplified OSLO form : [RCSTBPVKD][0-9]{1,2}\.[0-9]{1,2}\.[0-9]{1,2}	.1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.3
snMspsGeneralSwDate The revision date of software.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.4
snMspsGeneralSwDescription The description of software.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.4329.20.1.1.1.1.2.25.1.5

A table containing filtering information for VLANs
configured into the bridge by (local or network)
management, or learnt dynamically, specifying the set of
ports to which frames received on a VLAN for this FDB
and containing a specific Group destination address are
allowed to be forwarded. This table maintains context ID
	as one more index to support Multiple Instances.

snMspsDot1qTpGroupEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.4.1

Filtering information configured into the bridge by
management, or learnt dynamically, specifying the set of
ports to which frames received on a VLAN and containing
a specific Group destination address, are allowed to b…

Indexes

Q-BRIDGE-MIBdot1qVlanIndex snMspsDot1qTpGroupAddress snMspsDot1qTpPort

Column	Syntax	OID
snMspsDot1qTpGroupAddress The destination Group MAC address in a frame to which this entry's filtering information applies.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4329.20.1.1.1.1.3.4.1.1
snMspsDot1qTpPort The port number of the port for which this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.3.4.1.2
snMspsDot1qTpGroupIsLearnt Indicates whether the port is statically configured or a dynamic member of the Group address learnt through GMRP.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4329.20.1.1.1.1.3.4.1.3

A table containing the information of tagged, untagged
and forbidden ports for each VLAN.

snMspsDot1qVlanStaticPortConfigEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.8.1

Forwarding information about a port, Whether it is a
member or a forbidden member.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex snMspsDot1qTpPort

Column	Syntax	OID
snMspsDot1qVlanStaticPort Indicates whether the port is a member or a forbidden member in the forwarding information for this VLAN. 'addTagged' - to add the port in the tagged portlist. 'addUntagged' - to add the port in the untagged por…	Enumerationr/w Enumerated Values: 1 addTagged 2 addUntagged 3 addForbidden 4 delTagged 5 delUntagged 6 delForbidden	.1.3.6.1.4.1.4329.20.1.1.1.1.3.8.1.1

A table containing the information of AllowedToGoTo
ports for each static unicast entry. This table
maintains context ID as one more index to support
Multiple Instances.

snMspsDot1qStaticAllowedToGoEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.9.1

Information about a port, Whether it is an AllowedToGoTo
member or not.

Indexes

Q-BRIDGE-MIBdot1qFdbId Q-BRIDGE-MIBdot1qStaticUnicastAddress Q-BRIDGE-MIBdot1qStaticUnicastReceivePort snMspsDot1qTpPort

Column	Syntax	OID
snMspsDot1qStaticAllowedIsMember Indicates whether the port is an allowedToGoTo member.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4329.20.1.1.1.1.3.9.1.1

A table containing filtering information for Unicast
MAC addresses for each Filtering Database, configured
into the device by (local or network) management
specifying the set of ports to which frames received
from specific ports and containing specific unicast
destination addresses are allowed to be forwarded.  A
value of zero in this table as the port number from
which frames with a specific destination address are
received, is used to specify all ports for which there
is no specific entry in this table for that particular
destination address.  Entries are valid for unicast
addresses only. This table maintains context ID as
one more index to support Multiple Instances.

snMspsMIDot1qStaticUnicastExtnEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.10.1

Filtering information configured into the device by
(local or network) management specifying the set of
ports to which frames received from a specific port and
containing a specific unicast destination address are
allow…

Indexes

No indexes recorded

Column	Syntax	OID
snMspsMIDot1qStaticConnectionIdentifier This object is to associate the backbone MAC address of the peer backbone edge bridge with customer Mac addresses that can be reached through the peer backbone edge bridge.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4329.20.1.1.1.1.3.10.1.1

This table is used to maintain the status of static
and forbidden portlist required in ForwardAll table
for VLAN. This table maintains context ID as one more
index to support Multiple Instances.

snMspsDot1qForwardAllStatusEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.11.1

An entry to specify the status of static and
forbidden portlist in ForwardAll Table.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex

Column	Syntax	OID
snMspsDot1qForwardAllRowStatus This object indicates the status of the PortLists (Static, Forbidden) used in the forwarding information of a VLAN (ForwardAll). To fill the static and forbidden portlist, we have to set the rowstatus as 'NOT_IN_SERVICE…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.11.1.1

A table containing the	forwarding information of static
ports and forbidden ports for each VLAN. This table
maintains context ID as one more index to support
Multiple Instances.

snMspsDot1qForwardAllPortConfigEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.12.1

Forwarding information about a port, Whether it is a
member or a forbidden member.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex snMspsDot1qTpPort

Column	Syntax	OID
snMspsDot1qForwardAllPort Indicates whether the port is a member or a forbidden member in the forwarding information for this VLAN. 'addMember' - to add the port in the static member-list. 'addForbidden' - to add the po…	Enumerationr/w Enumerated Values: 1 addMember 2 addForbidden 3 delMember 4 delForbidden	.1.3.6.1.4.1.4329.20.1.1.1.1.3.12.1.1

This table is used to maintain the status of static
and forbidden portlist required in ForwardUnreg table
for VLAN. This table maintains context ID as one more
index to support Multiple Instances.

snMspsDot1qForwardUnregStatusEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.15.1

An entry to specify the status of static and
forbidden portlist in ForwardUnreg table.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex

Column	Syntax	OID
snMspsDot1qForwardUnregRowStatus This object indicates the status of the PortLists (Static, Forbidden) used in the forwarding information of a VLAN (ForwardUnreg). To fill the static and forbidden portlist, we have to set the rowstatus as 'NOT_IN_SERVI…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.15.1.1

A table containing the	information of static ports
and forbidden ports to which forwarding of multicast
group-addressed frames for which there is no more
specific forwarding information applies (per VLAN).
This table maintains context ID as one more index to
support Multiple Instances.

snMspsDot1qForwardUnregPortConfigEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.16.1

Forwarding information about a port, Whether it is a
member or a forbidden member.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex snMspsDot1qTpPort

Column	Syntax	OID
snMspsDot1qForwardUnregPort Indicates whether the port is a member or a forbidden member in the forwarding information for this VLAN. 'addMember' - to add the port in the static member-list. 'addForbidden' - to add the po…	Enumerationr/w Enumerated Values: 1 addMember 2 addForbidden 3 delMember 4 delForbidden	.1.3.6.1.4.1.4329.20.1.1.1.1.3.16.1.1

A table containing egress and forbidden ports for
static multicast entry. This table maintains context
ID as one more index to support Multiple Instance.

snMspsDot1qStaticMcastPortEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.18.1

Information about a port, Whether it is a member or
a forbidden member.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex Q-BRIDGE-MIBdot1qStaticMulticastAddress Q-BRIDGE-MIBdot1qStaticMulticastReceivePort snMspsDot1qTpPort

Column	Syntax	OID
snMspsDot1qStaticMcastPort Indicates whether the port is a member or a forbidden member in the static multicast entry. 'addMember' - to add the port in the egress member-list. 'addForbidden' - to add the port in the forb…	Enumerationr/w Enumerated Values: 1 addMember 2 addForbidden 3 delMember 4 delForbidden	.1.3.6.1.4.1.4329.20.1.1.1.1.3.18.1.1

Wild card vlan (Id : 0xFFF) static filtering information
will be used for all Vlans for which there is no specific
Static filtering exists in dot1qStaticUnicastTable or
dot1qStaticMulticastTable.

snMspsDot1qVlanWildCardEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.19.1

WildCard vlan filtering Information configured into device by
management to which frames received from any port and for any
vlan containing this wild card mac address as destination address
and for which there is no sta…

Indexes

snMspsDot1qVlanWildCardMacAddress

Column	Syntax	OID
snMspsDot1qVlanWildCardMacAddress The destination MAC address in a frame to which this entry's filtering information applies. This object must take the value of a Unicast, Multicast or Broadcast address.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4329.20.1.1.1.1.3.19.1.1
snMspsDot1qVlanWildCardEgressPorts The set of ports to which frames received from a specific port and destined for dot1qFutureVlanWildCardMacAddress address must be forwarded, if there is no specific static filtering entry exist for this MAC.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.4329.20.1.1.1.1.3.19.1.2
snMspsDot1qVlanWildCardRowStatus The row status of the entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.19.1.3

A Table containing ports to which frames received from a specific
port and destined for snMspsMIDot1qVlanWildCardMacAddress must be
forwarded, if there is no specific static filtering entry exist
for this MAC.

snMspsMIDot1qVlanWildCardPortEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.20.1

WildCard vlan filtering Information configured into device by
management specifying set of ports to which frames received
from any port and for any vlan containing
snMspsMIDot1qVlanWildCardMacAddress mac address as dest…

Indexes

snMspsDot1qVlanWildCardMacAddress snMspsDot1qTpPort

Column	Syntax	OID
snMspsMIDot1qVlanIsWildCardEgressPort Indicates whether the port is an egress port of wildcard entry.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4329.20.1.1.1.1.3.20.1.1

Table containing the port type information.

snMspsDot1qVlanPortEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.41.1

Entry indicating the type of the port.

Indexes

snMspsDot1qVlanPort

Column	Syntax	OID
snMspsDot1qVlanPort The port number of the port for which this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.3.41.1.1
snMspsDot1qVlanPortType The type of the port is by default hybrid port. When configured as access port, the port can accept and send only untagged frames. When configured as a trunk port, port is added as member of all the existing Vlans and a…	Enumerationr/w Enumerated Values: 1 accessPort 2 trunkPort 3 hybridPort 4 hostPort 5 promiscuousPort	.1.3.6.1.4.1.4329.20.1.1.1.1.3.41.1.2
snMspsDot1qVlanPortMacBasedClassification Object to expilicitly enable/disable the Mac based Classification on port. This can be independently set without any dependency in available configuration of snMspsDot1qVlanMacBasedOnAllPorts	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.3.41.1.3
snMspsDot1qVlanPortPortProtoBasedClassification Object to expilicitly enable/disable the port and protocol Classification on port. This can be independently set without any dependency in available configuration of snMspsDot1qVlanPortProtoBasedOnAllPorts	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.3.41.1.4
snMspsDot1qVlanFilteringUtilityCriteria Based on this object, learning on a port is decided. If default filtering utility Criteria is selected on a port, then learning of source mac from a received packet on that port will be done only if there…	Enumerationr/w Enumerated Values: 1 default 2 enhanced	.1.3.6.1.4.1.4329.20.1.1.1.1.3.41.1.5
snMspsDot1qVlanPortProtected The Split Horizon property of the port. If set to true, frames that are received on any other port that has the same property set to true, will not be forwarded on this port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4329.20.1.1.1.1.3.41.1.6
snMspsDot1qVlanPortSubnetBasedClassification Object to expilicitly enable/disable the Subnet based Vlan Classification on port. This can be independently set without any dependency in available configuration of snMspsDot1qVlanSubnetBasedOnAllPorts. This object is …	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.3.41.1.7

A table that contains information on Vlan-MAC address
mapping.

snMspsDot1qVlanPortMacMapEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.42.1

Entry that contains Vlan-MAC address mapping.

Indexes

snMspsDot1qVlanPort snMspsDot1qVlanPortMacMapAddr

Column	Syntax	OID
snMspsDot1qVlanPortMacMapAddr The Mac address for which the Vlan mapping is present in the entry.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4329.20.1.1.1.1.3.42.1.1
snMspsDot1qVlanPortMacMapVid The Vlan to which the mac address of this entry is mapped to.	Q-BRIDGE-MIBVlanIdr/w Type Constraints: range: 1..4094	.1.3.6.1.4.1.4329.20.1.1.1.1.3.42.1.2
snMspsDot1qVlanPortMacMapName The name given to the mac-vlan entry.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.4329.20.1.1.1.1.3.42.1.3
snMspsDot1qVlanPortMacMapMcastBcastOption Configurable option for discarding/allowing Multicast/Broadcast Untagged frames. The value allow (1) indicates that Multicast/Broadcast frames with source Mac address as in the Mac Vlan entry will be dropped if mac base…	Enumerationr/w Enumerated Values: 1 allow 2 suppress	.1.3.6.1.4.1.4329.20.1.1.1.1.3.42.1.4
snMspsDot1qVlanPortMacMapRowStatus The row status of the entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.42.1.5

This table contains information about the Filtering database identifier
(FID) used by vlan's to make forwarding decisions. Vlan's can be mapped
to use the same FID to share filtering information among them. This will
cause the mapped vlan's to operate in shared vlan learning (SVL) mode.
Vlan's mapped to a unique FID will operate in independent vlan learning
mode (IVL). A SET operation on this table is allowed only when
snMspsDotVlanLearningMode is hybrid. By default all vlan's will be
mapped to the FID equal to their vlan id when
snMspsDotVlanHybridTypeDefault is IVL. If the value of
snMspsDotVlanHybridTypeDefault is SVL all vlan's are mapped to
filtering database id 1.

snMspsDot1qVlanFidMapEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.43.1

Entry mapping VlanId to Filtering database id.

Indexes

snMspsDot1qVlanIndex

Column	Syntax	OID
snMspsDot1qVlanIndex VLAN ID for which filtering database information is available.	Unsigned32 Constraints: range: 1-4094	.1.3.6.1.4.1.4329.20.1.1.1.1.3.43.1.1
snMspsDot1qVlanFid The Filtering database id (FID) that will be used by the vlan.	Unsigned32r/w Constraints: range: 1-4094	.1.3.6.1.4.1.4329.20.1.1.1.1.3.43.1.2

The table contains the statistics on a per VLAN basis.
It contains number of unicast, broadcast and unknown unicast
packets flooded per VLAN.

snMspsDot1qVlanCounterEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.44.1

The entry contains the VLAN statistics

Indexes

snMspsDot1qVlanIndex

Column	Syntax	OID
snMspsDot1qVlanCounterRxUcast Number of unicast packets received in this VLAN.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.44.1.1
snMspsDot1qVlanCounterRxMcastBcast Number of multicast/broadcast packets received in this VLAN.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.44.1.2
snMspsDot1qVlanCounterTxUnknUcast Number of unknown unicast packets flooded in this VLAN.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.44.1.3
snMspsDot1qVlanCounterTxUcast Number of known unicast packets forwarded in this VLAN.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.44.1.4
snMspsDot1qVlanCounterTxBcast Number of broadcast packets forwarded in this VLAN.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.44.1.5

A table containing per VLAN Unicast MAC address control information.
The control information includes the status of unicast MAC address
learning as well as restricting the number of unique entries learnt to
a specified limit for the specified VLAN.

snMspsDot1qVlanUnicastMacControlEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.45.1

Information controlling the number of distinct unicast MAC addresses
that can be learnt by a VLAN depending on whether learning is enabled
or disabled for the specified VLAN.

Indexes

snMspsDot1qVlanIndex

Column	Syntax	OID
snMspsDot1qVlanUnicastMacLimit The Limiting value on the number of distinct unicast MAC addresses learnt in a VLAN. The lower limit and upper limit value that can be SET for this object is determined by the underlying hardware.	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.45.1.1
snMspsDot1qVlanAdminMacLearningStatus A Truth value used to configure the unicast MAC learning Admin status for the VLAN to either be enabled (1) or disabled (2).	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.3.45.1.2
snMspsDot1qVlanOperMacLearningStatus A Truth value indicating the unicast MAC learning enabled/disabled Operational status for the specified VLAN. If the VLAN does not have any member port, then the Mac Learning Status for this VLAN will always be disabled…	P-BRIDGE-MIBEnabledStatus Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.3.45.1.3

An extention to the dot1qTpFdbTable contains information
about unicast entries only learned via pseudowire
for which the device has forwarding and/or filtering
information. This information is used by the
transparent bridging function in determining how to
propagate a received frame.

snMspsDot1qVlanTpFdbEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.46.1

Information about the pseudowire on which MAC address was
learned

Indexes

No indexes recorded

Column	Syntax	OID
snMspsDot1qVlanTpFdbPw Either the value '0', or the pseudowire number on which a frame having a source address equal to the value of the corresponding instance of dot1qTpFdbAddress has been seen. A value of '0' indicates that the entry was le…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.46.1.1
snMspsDot1qTpOldFdbPort This object is useful for generating the source relearning trap. When a get is performed on this object, it returns the value of Zero(0), so that the device walk doesn't break. It indicates the port through which the ma…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.3.46.1.2
snMspsDot1qConnectionIdentifier This object is to associate the backbone MAC address of the peer backbone edge brige with customer Mac addresses that can be reached through the peer backbone edge bridge.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4329.20.1.1.1.1.3.46.1.3

A table to configure VLAN priorization

snMspsDot1qVlanPriorityEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.47.1

Indexes

snMspsDot1qVlanPriorityVid

Column	Syntax	OID
snMspsDot1qVlanPriorityVid VLAN-ID	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.4329.20.1.1.1.1.3.47.1.1
snMspsDot1qVlanPriorityEnabled Enable/Disable forcing of a given priority for all frames received on a certain VLAN	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.3.47.1.4
snMspsDot1qVlanPriority Priority that is forced for all frames received on a certain VLAN	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.4329.20.1.1.1.1.3.47.1.7

An extension to dot1qVlanStaticTable VLAN table.
This table contains the Private Vlan (PVLAN) related
configurations.
          
Only considered if device supports corresponding functionality, 
otherwise any set operation will fail with an inconsistentValue error 
and get will return empty.
          
Entries cannot be created or deleted by user, whenever static vlan 
entry created in the table 'dot1qVlanStaticTable' user can configure 
corresponding private vlan properties in this table.

snMspsDot1qStVlanExtEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.48.20.1

Each entry specifies the Private Vlan configuration done for
a given Vlan.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex

Column	Syntax	OID
snMspsDot1qStVlanPVlanType This object identifies the Private vlan type for this vlan. normal - Vlan does not belong to any Private VLAN domain. primary - Primary vlan in a Private VLAN domain. isolated - Isolated vlan in a Private VLAN dom…	Enumerationr/w Enumerated Values: 1 normal 2 primary 3 isolated 4 community	.1.3.6.1.4.1.4329.20.1.1.1.1.3.48.20.1.1
snMspsDot1qStVlanPrimaryVid This object identifies the primary vlan assoicated with this vlan. For primary and normal vlans, this object will have the value zero and configuring this object to non-zero value will not be allowed for them. For se…	Q-BRIDGE-MIBVlanIdOrNoner/w Type Constraints: range: 0..4094	.1.3.6.1.4.1.4329.20.1.1.1.1.3.48.20.1.2

A table that contains mappings from Protocol
Templates to Protocol Group Identifiers used for
Port-and-Protocol-based VLAN Classification.

snMspsDot1vProtocolGroupEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.49.1.1

A mapping from a Protocol Template to a Protocol
Group Identifier.

Indexes

snMspsDot1vProtocolTemplateFrameType snMspsDot1vProtocolTemplateProtocolValue snMspsDot1vProtocolGroupId

Column	Syntax	OID
snMspsDot1vProtocolTemplateFrameType The data-link encapsulation format or the 'detagged_frame_type' in a Protocol Template.	Enumeration Enumerated Values: 1 ethernet 2 rfc1042 3 snap8021H 4 snapOther 5 llcOther	.1.3.6.1.4.1.4329.20.1.1.1.1.3.49.1.1.1
snMspsDot1vProtocolTemplateProtocolValue The identification of the protocol above the data-link layer in a Protocol Template. Depending on the frame type, the octet string will have one of the following values: For 'ethernet', 'rfc1042' and 'sn…	OctetString Constraints: range: 2-2 range: 5-5	.1.3.6.1.4.1.4329.20.1.1.1.1.3.49.1.1.2
snMspsDot1vProtocolGroupId Represents a group of protocols that are associated together when assigning a VID to a frame.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.4329.20.1.1.1.1.3.49.1.1.3
snMspsDot1vProtocolGroupRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.49.1.1.4

This table contains information about the tunnel ports. A walk on
this table will show only those interfaces that are configured for
tunneling.
This table is supported only when the Bridge is configured in Provider
Bridge (Q-in-Q) mode.

snMspsVlanTunnelEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.51.7.1

Entry indicating the tunnel information of the port.

Indexes

snMspsVlanPort

Column	Syntax	OID
snMspsVlanPort The Index value of the port in the system for which this entry applies. The maximum index value of the port is defined by the system.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.7.1.1
snMspsVlanTunnelStatus Indicates whether Tunnelling is enabled or disabled on this port. snMspsVlanTunnelStatus can be set to `enabled` if and only if the Bridge mode is set to be `Provider Bridge Mode` and VLAN port type is set to 'accessPor…	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.7.1.2

This table contains information about the handling (Tunnel/Peer/
Discard)of customer Layer 2 protocols (STP/GVRP/GMRP/LACP/Dot1x/
IGMP/MVRP and MMRP) inside a given network.

snMspsVlanTunnelProtocolEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.51.8.1

Entry indicating the handling (Tunnel/Peer/Discard) of Layer 2
protocols (STP/GVRP/GMRP/LACP/Dot1x/IGMP/MVRP and MMRP) on this port.

Tunnel Status cannot be set to `tunnel/discard`, if the protocol
is enabl…

Indexes

snMspsVlanPort

Column	Syntax	OID
snMspsVlanTunnelProtocolDot1x The object to specify whether to peer/tunnel/discard the Dot1x packets received on this port.	TunnelStatusr/w Type Values: 1 peer 2 tunnel 3 discard Description: To specify how to handle the L2 protocol packets received on a particular port. When the option is set to 'peer', the L2 protocol packets received on a particular port will be processed in the Bridge. …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.8.1.1
snMspsVlanTunnelProtocolLacp The object to specify whether to peer/tunnel/discard the LACP packets received on this port.	TunnelStatusr/w Type Values: 1 peer 2 tunnel 3 discard Description: To specify how to handle the L2 protocol packets received on a particular port. When the option is set to 'peer', the L2 protocol packets received on a particular port will be processed in the Bridge. …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.8.1.2
snMspsVlanTunnelProtocolStp The object to specify whether to peer/tunnel/discard the STP packets received on this port.	TunnelStatusr/w Type Values: 1 peer 2 tunnel 3 discard Description: To specify how to handle the L2 protocol packets received on a particular port. When the option is set to 'peer', the L2 protocol packets received on a particular port will be processed in the Bridge. …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.8.1.3
snMspsVlanTunnelProtocolGvrp The object to specify whether to peer/tunnel/discard the GVRP packets received on this port.	TunnelStatusr/w Type Values: 1 peer 2 tunnel 3 discard Description: To specify how to handle the L2 protocol packets received on a particular port. When the option is set to 'peer', the L2 protocol packets received on a particular port will be processed in the Bridge. …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.8.1.4
snMspsVlanTunnelProtocolGmrp The object to specify whether to peer/tunnel/discard the GMRP packets received on this port.	TunnelStatusr/w Type Values: 1 peer 2 tunnel 3 discard Description: To specify how to handle the L2 protocol packets received on a particular port. When the option is set to 'peer', the L2 protocol packets received on a particular port will be processed in the Bridge. …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.8.1.5
snMspsVlanTunnelProtocolIgmp The object to specify whether to peer/tunnel/discard the IGMP packets received on this port.	TunnelStatusr/w Type Values: 1 peer 2 tunnel 3 discard Description: To specify how to handle the L2 protocol packets received on a particular port. When the option is set to 'peer', the L2 protocol packets received on a particular port will be processed in the Bridge. …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.8.1.6
snMspsVlanTunnelProtocolMvrp The object to specify whether to peer/tunnel/discard the MVRP packets received on this port.	TunnelStatusr/w Type Values: 1 peer 2 tunnel 3 discard Description: To specify how to handle the L2 protocol packets received on a particular port. When the option is set to 'peer', the L2 protocol packets received on a particular port will be processed in the Bridge. …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.8.1.7
snMspsVlanTunnelProtocolMmrp The object to specify whether to peer/tunnel/discard the MMRP packets received on this port.	TunnelStatusr/w Type Values: 1 peer 2 tunnel 3 discard Description: To specify how to handle the L2 protocol packets received on a particular port. When the option is set to 'peer', the L2 protocol packets received on a particular port will be processed in the Bridge. …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.8.1.8

This table contains statistics information about the tunneled
Layer 2 protocols (STP/GVRP/GMRP/LACP/Dot1x/IGMP/MVRP and MMRP)
received and transmitted over a port.

snMspsVlanTunnelProtocolStatsEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1

Entry indicating the handling (Tunnel/Peer/Discard) of Layer 2
protocols (STP/GVRP/GMRP/LACP/Dot1x/IGMP/MVRP and MMRP) on this port.

Indexes

snMspsVlanPort

Column	Syntax	OID
snMspsVlanTunnelProtocolDot1xPktsRecvd The number of tunneled Dot1x Packets received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.1
snMspsVlanTunnelProtocolDot1xPktsSent The number of tunneled Dot1x Packets transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.2
snMspsVlanTunnelProtocolLacpPktsRecvd The number of tunneled LACP Packets received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.3
snMspsVlanTunnelProtocolLacpPktsSent The number of tunneled LACP packets transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.4
snMspsVlanTunnelProtocolStpPDUsRecvd The number of tunneled STP PDUs received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.5
snMspsVlanTunnelProtocolStpPDUsSent The number of tunneled STP PDUs transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.6
snMspsVlanTunnelProtocolGvrpPDUsRecvd The number of tunneled GVRP PDUs received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.7
snMspsVlanTunnelProtocolGvrpPDUsSent The number of tunneled GVRP PDUs transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.8
snMspsVlanTunnelProtocolGmrpPktsRecvd The number of tunneled GMRP PDUs packets received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.9
snMspsVlanTunnelProtocolGmrpPktsSent The number of tunneled GMRP packets transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.10
snMspsVlanTunnelProtocolIgmpPktsRecvd The number of tunneled IGMP packets received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.11
snMspsVlanTunnelProtocolIgmpPktsSent The number of tunneled IGMP packets transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.12
snMspsVlanTunnelProtocolMvrpPktsRecvd The number of MVRPDUs received on a port for which the MVRP tunneling status is enabled.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.13
snMspsVlanTunnelProtocolMvrpPktsSent The number of MVRPDUs transmitted on a port on which the MVRP tunneling status is enabled.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.14
snMspsVlanTunnelProtocolMmrpPktsRecvd The number of MMRPDUs received on a port for which the MMRP tunneling status is enabled.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.15
snMspsVlanTunnelProtocolMmrpPktsSent The number of MMRPDUs transmitted on a port on which the MMRP tunneling status is enabled.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.51.9.1.16

This table contains statistics information about the L2 protocol
packets (STP/GVRP/GMRP/LACP/Dot1x/IGMP/MVRP and MMRP) discarded on
reception and transmission side due to 'Discard' tunnel protocol
status.

snMspsVlanDiscardStatsEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1

Entry indicating the Discard statistics for L2 protocol packets.

Indexes

snMspsVlanPort

Column	Syntax	OID
snMspsVlanDiscardDot1xPktsRx The number of Dot1x packets discarded on the reception side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.1
snMspsVlanDiscardDot1xPktsTx The number of Dot1x packets discarded on the transmission side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.2
snMspsVlanDiscardLacpPktsRx The number of LACP packets discarded on the reception side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.3
snMspsVlanDiscardLacpPktsTx The number of LACP packets discarded on the transmission side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.4
snMspsVlanDiscardStpPDUsRx The number of STP BPDUs discarded on the reception side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.5
snMspsVlanDiscardStpPDUsTx The number of STP BPDUs discarded on the transmission side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.6
snMspsVlanDiscardGvrpPktsRx The number of GVRP packets discarded on the reception side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.7
snMspsVlanDiscardGvrpPktsTx The number of GVRP packets discarded on the transmission side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.8
snMspsVlanDiscardGmrpPktsRx The number of GMRP packets discarded on the reception side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.9
snMspsVlanDiscardGmrpPktsTx The number of GMRP packets discarded on the transmission side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.10
snMspsVlanDiscardIgmpPktsRx The number of IGMP packets discarded on the reception side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.11
snMspsVlanDiscardIgmpPktsTx The number of IGMP packets discarded on the transmission side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.12
snMspsVlanDiscardMvrpPktsRx The number of MVRP packets discarded on the reception side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.13
snMspsVlanDiscardMvrpPktsTx The number of MVRP packets discarded on the transmission side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.14
snMspsVlanDiscardMmrpPktsRx The number of MMRP packets discarded on the receiption side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.15
snMspsVlanDiscardMmrpPktsTx The number of MMRP packets discarded on the transmission side due to Discard option.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4329.20.1.1.1.1.3.52.1.1.16

Subnet based VLAN classification - The source IP-subnet address in
the incoming packets is used to classify VLAN membership.
Subnet based VLAN is applied only on IP/ARP packets.
This table contains information on Subnet-VlanId address mapping.
In case of BCM, the snMspsDot1qVlanPort index should always be 0 since
BCM supports Subnet based VLAN globally (not on per port)

snMspsDot1qVlanPortSubnetMapEntry row .1.3.6.1.4.1.4329.20.1.1.1.1.3.57.1

Entry that contains Vlan-Subnet address mapping.

Indexes

snMspsDot1qVlanPort snMspsDot1qVlanPortSubnetMapAddr

Column	Syntax	OID
snMspsDot1qVlanPortSubnetMapAddr The Source IP-Subnet address for which the Vlan mapping is present in the entry.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.4329.20.1.1.1.1.3.57.1.1
snMspsDot1qVlanPortSubnetMapVid The Vlan to which the Source IP-Subnet address of this entry is mapped to.	Q-BRIDGE-MIBVlanIdr/w Type Constraints: range: 1..4094	.1.3.6.1.4.1.4329.20.1.1.1.1.3.57.1.2
snMspsDot1qVlanPortSubnetMapARPOption Configurable option for discarding/allowing ARP Untagged frames on the vlan. The value allow (1) indicates that ARP frames with source IP-subnet address matching the snMspsDot1qVlanPortSubnetMapEntry will be classified …	Enumerationr/w Enumerated Values: 1 allow 2 suppress	.1.3.6.1.4.1.4329.20.1.1.1.1.3.57.1.3
snMspsDot1qVlanPortSubnetMapRowStatus The row status of the entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4329.20.1.1.1.1.3.57.1.4
snMspsDot1qVlanPortSubnetMapSubnetMask The Source IP-Subnet Mask for which the Vlan mapping is present in the entry.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.4329.20.1.1.1.1.3.57.1.5