PW-TDM-R-MIB Table View

This table contains basic information including ifIndex,  
and pointers to entries in the relevant TDM config 
tables for this TDM PW.

pwTDMEntry row .1.3.6.1.4.1.164.20.13.1.1.1

This table is indexed by the same index that was
created for the associated entry in the PW Table
(in the PW-STD-MIB).

- The PwIndex.

An entry is created in this table by the agent for ev…

Indexes

PW-STD-R-MIBpwIndex

Column	Syntax	OID
pwTDMRate The parameter represents the bit-rate of the TDM service in multiples of the 'basic' 64 Kbit/s rate [TDMCP-EXT]. It complements the definition of pwType used in PW-STD-MIB. For structure-agnostic the following shou…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.20.13.1.1.1.1
pwTDMIfIndex This is a unique index within the ifTable. It represents the interface index of the full link or the interface index for the bundle holding the group of time slots to be transmitted via this PW connection. …	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.164.20.13.1.1.1.2
pwGenTDMCfgIndex Index to the generic parameters in the TDM configuration table that appears in this MIB module. It is likely that multiple TDM PWs of the same characteristic will share a single TDM Cfg entry.	PW-TC-STD-R-MIBPwCfgIndexOrzeror/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.1.1.3
pwRelTDMCfgIndex Index to the relevant TDM configuration table entry that appears in one of the related MIB modules such as TDMoIP or CESoPSN. It is likely that multiple TDM PWs of the same characteristic will share a single config…	PW-TC-STD-R-MIBPwCfgIndexOrzeror/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.1.1.4
pwTDMConfigError Any of the bits are set if the local configuration is not compatible with the peer configuration as available from the various parameters options. Setting is done based on signaling, or else value (0) will be set. …	Bits Enumerated Values: 0 notApplicable 1 tdmTypeIncompatible 2 peerRtpIncompatible 3 peerPayloadSizeIncompatible	.1.3.6.1.4.1.164.20.13.1.1.1.5
pwTDMTimeElapsed The number of seconds, including partial seconds, that have elapsed since the beginning of the current measurement period. If, for some reason, such as an adjustment in the system's time-of-day clock, the current in…	Integer32 Constraints: range: 1-900	.1.3.6.1.4.1.164.20.13.1.1.1.6
pwTDMValidIntervals The number of previous 15-minute intervals for which data was collected. An agent with TDM capability must be capable of supporting at least n intervals. The minimum value of n is 4, The default of n is 32 and t…	Integer32 Constraints: range: 0-96	.1.3.6.1.4.1.164.20.13.1.1.1.7
pwTDMValidDayIntervals The number of previous days for which data was collected. An agent with TDM capability must be capable of supporting at least n intervals. The minimum value of n is 1, The default of n is 1 and the maximum value…	Integer32 Constraints: range: 0-30	.1.3.6.1.4.1.164.20.13.1.1.1.8
pwTDMCurrentIndicationsdeprecated The following defects should be detected and reported upon request: -Stray packets MAY be detected by the PSN and multiplexing layers. Stray packets MUST be discarded by the CE-bound IWF and t…	Bits Enumerated Values: 0 other 1 strayPacket 2 malformedPacket 3 excessivePktLossRate 4 bufferOverrun 5 bufferUnderrun 6 remotePktLoss 7 pktMisOrder 8 packetLoss 9 tdmFault	.1.3.6.1.4.1.164.20.13.1.1.1.9
pwTDMLatchedIndicationsdeprecated The state of TDM indicators when the TDM PW last declared an error second (either as ES, SES or a second with errors inside a UAS) condition. At this time, only LOPS can create a failure. Since indicators other than …	Bits Enumerated Values: 0 other 1 strayPacket 2 malformedPacket 3 excessivePktLossRate 4 bufferOverrun 5 bufferUnderrun 6 remotePktLoss 7 pktMisOrder 8 packetLoss 9 tdmFault	.1.3.6.1.4.1.164.20.13.1.1.1.10
pwTDMLastEsTimeStamp The value of sysUpTime at the most recent occasion at which the TDM PW entered the ES or SES state.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.164.20.13.1.1.1.11

This table contains a set of parameters that may be 
referenced by one or more TDM PWs in pwTDMTable.

pwTDMCfgEntry row .1.3.6.1.4.1.164.20.13.1.3.1

These parameters define the characteristics of a
TDM PW. They are grouped here to ease NMS burden.
Once an entry is created here it may be re-used
by many PWs.
Unless otherwise specified, all objects in this table
MU…

Indexes

pwTDMCfgIndex

Column	Syntax	OID
pwTDMCfgIndex Index to an entry in this table. The value is a copy of the assigned pwTDMCfgIndexNext	PwTDMCfgIndex Type Constraints: range: 1..4294967295	.1.3.6.1.4.1.164.20.13.1.3.1.1
pwTDMCfgRowStatus Object used for creating, modifying, and deleting a row from this table. The following objects should not be modified if the entry is in used and the status is active: pwTDMCfgPayloadSize, pwTDMCfgRtpHdrUsed, pwTDMCf…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.13.1.3.1.2
pwTDMCfgConfErrdeprecated Various configuration errors. Illegal settings within the pwTDMCfg table. Setting is done based on signaling, or else value (0) will be set	Bits Enumerated Values: 0 notApplicable 1 payloadSize 2 jtrBfrDepth	.1.3.6.1.4.1.164.20.13.1.3.1.3
pwTDMCfgPayloadSize The value of this object indicates the PayLoad Size (in bytes) to be defined during the PW setUp. Upon TX, implementation must be capable of carrying that amount of bytes. Upon RX, when the LEN field is set to 0, the…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.3.1.4
pwTDMCfgPktReorder If set True: as CE bound packets are queued in the jitter buffer, out of order packets are re-ordered. The maximum sequence number differential (i.e., the range in which re-sequencing can occur) is dependant on the …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.13.1.3.1.5
pwTDMCfgRtpHdrUsed If set to False: an RTP header is not pre-pended to the TDM packet.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.13.1.3.1.6
pwTDMCfgJtrBfrDepth The size of this buffer SHOULD be locally configured to allow accommodation to the PSN-specific packet delay variation. If configured to a value not supported by the implementation, the agent MUST…	microsecondSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.3.1.7
pwTDMCfgPayloadSuppression Selecting 'enable' means: Payload suppression is allowed. Payload MAY be omitted in order to conserve bandwidth. Selecting 'disable' means: no suppresion under any condition. Object MAY be changed at any time.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.164.20.13.1.3.1.8
pwTDMCfgConsecPktsInSynch The number of consecutive packets with sequential sequence numbers that are required to exit the LOPS state. Object MAY be changed when the related PW is defined as not active.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.3.1.9
pwTDMCfgConsecMissPktsOutSynch The number of consecutive missing packets that are required to enter the LOPS state. Object MAY be changed when the related PW is defined as not active.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.3.1.10
pwTDMCfgSetUp2SynchTimeOut The amount of time the host should wait before declaring the pseudo wire in down state, if the number of consecutive TDM packets that have been received after changing the adminstrative status to up and after finali…	millisecondSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.3.1.11
pwTDMCfgPktReplacePolicy This parameter determines the value to be played when CE bound packets have over/underflow the jitter buffer, or are missing for any reason. This byte pattern is sent(played)on the TDM line. Selecting implementationSpe…	Enumerationr/w Enumerated Values: 1 allOnes 2 implementationSpecific 3 filler	.1.3.6.1.4.1.164.20.13.1.3.1.12
pwTDMCfgAvePktLossTimeWindow The length of time over which the average packet loss rate should be computed to detect Excessive packet loss rate. Object MAY be changed when the related PW is defined as not active.	millisecondSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.20.13.1.3.1.13
pwTDMCfgExcessivePktLossThreshold Excessive packet loss rate is detected by computing the average packetloss rate over a pwTDMCfgAvePktLossTimeWindow amount of time and comparing it with this threshold value. The rate is expressed in precentage. Ob…	PercentSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.3.1.14
pwTDMCfgAlarmThreshold Alarms are only reported when the defect state persists for the length of time specified by this object. The object's unit is millisec. Object MAY be changed when the related PW is defined as not active.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.3.1.15
pwTDMCfgClearAlarmThreshold Alarm MUST be cleared after the corresponding defect is undetected for the amount of time specified by this object. The object's unit is millisec. Object MAY be changed when the related PW is defined as not active.	SNMPv2-SMIUnsigned32r/w Constraints: range: 0-160	.1.3.6.1.4.1.164.20.13.1.3.1.16
pwTDMCfgMissingPktsToSes Percent of missing packets detected (consecutive or not) within a 1 second window to cause a Severely Error Second (SES) to be counted. Object MAY be changed when the related PW is defined as not active.	PercentSNMPv2-SMIUnsigned32r/w Constraints: range: 0-5	.1.3.6.1.4.1.164.20.13.1.3.1.17
pwTDMCfgTimestampMode Timestamp generation MAY be used in one of the following modes: 1. Absolute mode: the PSN-bound IWF sets timestamps using the clock recovered from the incoming TDM attachment circuit. As a consequence, the timest…	Enumerationr/w Enumerated Values: 1 notApplicable 2 absolute 3 differential	.1.3.6.1.4.1.164.20.13.1.3.1.18
pwTDMCfgStorageType This variable indicates the storage type for this row.	SNMPv2-TCStorageTyper/w Constraints: range: 1-8 Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.164.20.13.1.3.1.19
pwTDMCfgPktFiller Filler byte pattern played out on the TDM interface if pwTDMCfgPktReplacePolicy was set to filler(3). Object MAY be changed when the related PW is defined as not active.	Unsigned32r/w Constraints: range: 0-255 range: 0-160	.1.3.6.1.4.1.164.20.13.1.3.1.20
pwTDMCfgName A descriptive string, prefereably unique name, to an entry in this table. Object MAY be changed at any time.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.13.1.3.1.21

The current 15 minute interval counts are in  
this table. 
            
This table provides per TDM PW performance information.

pwTDMPerfCurrentEntry row .1.3.6.1.4.1.164.20.13.1.5.1

An entry in this table is created by the agent for every
pwTDMTable entry. After 15 minutes, the contents of this
table entry are copied to a new entry in the
pwTDMPerfInterval table and the counts in this entry
ar…

Indexes

PW-STD-R-MIBpwIndex

Column	Syntax	OID
pwTDMPerfCurrentMissingPkts Number of missing packets (as detected via control word sequence number gaps).	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.13.1.5.1.1
pwTDMPerfCurrentPktsReOrder Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.13.1.5.1.2
pwTDMPerfCurrentJtrBfrUnderruns Number of times a packet needed to be played out and the jitter buffer was empty.	PerfHist-TC-MIBPerfCurrentCount Constraints: range: 1-15	.1.3.6.1.4.1.164.20.13.1.5.1.3
pwTDMPerfCurrentMisOrderDropped Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.13.1.5.1.4
pwTDMPerfCurrentMalformedPkt Number of packets detected with unexpected size, or bad headers' stack	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.13.1.5.1.5
pwTDMPerfCurrentESs The counter associated with the number of Error Seconds encountered. Any malformed packet, seq. error, LOPS and similar are considered as error second	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.13.1.5.1.6
pwTDMPerfCurrentSESs The counter associated with the number of Severely Error Seconds encountered.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.13.1.5.1.7
pwTDMPerfCurrentUASs The counter associated with the number of Unavailable Seconds encountered. Any consequtive ten seconds of SES are counted as one UAS	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.13.1.5.1.8
pwTDMPerfCurrentFC TDM Failure Counts (FC-TDM). The number of TDM failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. A failure event that begins in one period and ends in an…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.13.1.5.1.9

This table provides performance information per TDM PW 
similar to the pwTDMPerfCurrentTable above. However, 
these counts represent historical 15 minute intervals. 
Typically, this table will have a maximum of 96 entries 
for a 24 hour period, but is not limited to this.

pwTDMPerfIntervalEntry row .1.3.6.1.4.1.164.20.13.1.6.1

An entry in this table is created by the agent for
every pwTDMPerfCurrentEntry that is 15 minutes old.
The contents of the Current entry are copied to the new
entry here. The Current entry, then resets its counts
to…

Indexes

PW-STD-R-MIBpwIndex pwTDMPerfIntervalNumber

Column	Syntax	OID
pwTDMPerfIntervalNumber A number (normally between 1 and 96 to cover a 24 hour period) which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interva…	SNMPv2-SMIUnsigned32 Constraints: range: 1-4094	.1.3.6.1.4.1.164.20.13.1.6.1.1
pwTDMPerfIntervalValidData This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.13.1.6.1.2
pwTDMPerfIntervalDuration The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.6.1.3
pwTDMPerfIntervalMissingPkts Number of missing packets (as detected via control word sequence number gaps).	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.13.1.6.1.4
pwTDMPerfIntervalPktsReOrder Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this Feature.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.13.1.6.1.5
pwTDMPerfIntervalJtrBfrUnderruns Number of times a packet needed to be played out and the jitter buffer was empty.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.13.1.6.1.6
pwTDMPerfIntervalMisOrderDropped Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer.	PerfHist-TC-MIBPerfIntervalCount Constraints: range: 1-16	.1.3.6.1.4.1.164.20.13.1.6.1.7
pwTDMPerfIntervalMalformedPkt Number of packets detected with unexpected size, or bad headers' stack	PerfHist-TC-MIBPerfIntervalCount Constraints: range: 1-16	.1.3.6.1.4.1.164.20.13.1.6.1.8
pwTDMPerfIntervalESs The counter associated with the number of Error Seconds encountered.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.13.1.6.1.9
pwTDMPerfIntervalSESs The counter associated with the number of Severely Error Seconds encountered.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.13.1.6.1.10
pwTDMPerfIntervalUASs The counter associated with the number of Unavailable Seconds encountered.	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.13.1.6.1.11
pwTDMPerfIntervalFC TDM Failure Counts (FC-TDM). The number of TDM failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared. A failure event that begins in one period and ends in an…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.13.1.6.1.12

This table provides performance information per TDM PW 
similar to the pwTDMPerfIntervalTable above. However, 
these counters represent historical 1 day intervals up to
one full month. The table consists of real time data, as 
such it is not persistence across re-boot.

pwTDMPerf1DayIntervalEntry row .1.3.6.1.4.1.164.20.13.1.7.1

An entry is created in this table by the agent
for every entry in the pwTDMTable table.

Indexes

PW-STD-R-MIBpwIndex pwTDMPerf1DayIntervalNumber

Column	Syntax	OID
pwTDMPerf1DayIntervalNumber The number of interval, where 1 indicates current day measured period and 2 and above indicate previous days respectively	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.7.1.1
pwTDMPerf1DayIntervalValidData This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.13.1.7.1.2
pwTDMPerf1DayIntervalDuration The duration of a particular interval in seconds, Adjustments in the system's time-of-day clock, may cause the interval to be greater or less than, the normal value. Therefore this actual interval value is provided.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.7.1.3
pwTDMPerf1DayIntervalMissingPkts Number of missing packets (as detected via control word sequence number gaps).	SNMPv2-SMICounter32 Constraints: range: 1-3600	.1.3.6.1.4.1.164.20.13.1.7.1.4
pwTDMPerf1DayIntervalPktsReOrder Number of packets detected out of sequence (via control word sequence number), but successfully re-ordered. Note: some implementations may not support this feature.	SNMPv2-SMICounter32 Constraints: range: 1-3600	.1.3.6.1.4.1.164.20.13.1.7.1.5
pwTDMPerf1DayIntervalJtrBfrUnderruns Number of times a packet needed to be played out and the jitter buffer was empty.	SNMPv2-SMICounter32 Constraints: range: 0-3600	.1.3.6.1.4.1.164.20.13.1.7.1.6
pwTDMPerf1DayIntervalMisOrderDropped Number of packets detected out of order(via control word sequence numbers), and could not be re-ordered, or could not fit in the jitter buffer.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.7.1.7
pwTDMPerf1DayIntervalMalformedPkt Number of packets detected with unexpected size, or bad headers' stack.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.7.1.8
pwTDMPerf1DayIntervalESs The counter associated with the number of Error Seconds encountered.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.7.1.9
pwTDMPerf1DayIntervalSESs The counter associated with the number of Severely Error Seconds.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.7.1.10
pwTDMPerf1DayIntervalUASs The counter associated with the number of UnAvailable Seconds. NOTE: When first entering the UAS state, the number of SES To UAS is added to this object, then as each additional UAS occurs, this obj…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.7.1.11
pwTDMPerf1DayIntervalFC TDM Failure Counts (FC-TDM). The number of TDM failure events. A failure event begins when the LOPS failure is declared, and ends when the failure is cleared.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.13.1.7.1.12