pwTDMCfgExcessivePktLossThreshold
PW-TDM-R-MIB ·
.1.3.6.1.4.1.164.20.13.1.3.1.14
Object
Excessive packet loss rate is detected by computing the average packetloss rate over a pwTDMCfgAvePktLossTimeWindow amount of time and comparing it with this threshold value. The rate is expressed in precentage. Object MAY be changed when the related PW is defined as not active.
Context
- MIB
- PW-TDM-R-MIB
- OID
.1.3.6.1.4.1.164.20.13.1.3.1.14- Type
- column
- Access
- readwrite
- Status
- current
- Units
- Percent
- Parent
- pwTDMCfgEntry
- Table
- pwTDMCfgTable
- Siblings
- 20
Syntax
Percent SNMPv2-SMIUnsigned32
- Source
- SNMPv2-SMIUnsigned32
- Base type
Unsigned32
Values & Constraints
Type Constraints
range: 0..4294967295
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| pwTDMCfgIndex Index to an entry in this table. The value is a copy of the
assigned pwTDMCfgIndexNext | column | PwTDMCfgIndex | .1.3.6.1.4.1.164.20.13.1.3.1.1 |
| pwTDMCfgConsecMissPktsOutSynch The number of consecutive missing packets that are
required to enter the LOPS state.
Object MAY be changed when the related PW is
defined as not active. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.20.13.1.3.1.10 |
| pwTDMCfgSetUp2SynchTimeOut The amount of time the host should wait before declaring the
pseudo wire in down state, if the number of consecutive
TDM packets that have been received after changing the
adm… | column | millisecond SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.20.13.1.3.1.11 |
| pwTDMCfgPktReplacePolicy This parameter determines the value to be played when CE bound
packets have over/underflow the jitter buffer, or are missing
for any reason. This byte pattern is sent(played)on
t… | column | Enumeration | .1.3.6.1.4.1.164.20.13.1.3.1.12 |
| pwTDMCfgAvePktLossTimeWindow The length of time over which the average packet
loss rate should be computed to detect Excessive packet
loss rate.
Object MAY be changed when the related PW is
defined as not … | column | millisecond SNMPv2-SMIInteger32 | .1.3.6.1.4.1.164.20.13.1.3.1.13 |
| pwTDMCfgAlarmThreshold Alarms are only reported when the defect state persists
for the length of time specified by this object.
The object's unit is millisec.
Object MAY be changed when the related PW… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.20.13.1.3.1.15 |
| pwTDMCfgClearAlarmThreshold Alarm MUST be cleared after the corresponding defect is
undetected for the amount of time specified by this object.
The object's unit is millisec.
Object MAY be changed when th… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.20.13.1.3.1.16 |
| pwTDMCfgMissingPktsToSes Percent of missing packets detected (consecutive or not)
within a 1 second window to cause a Severely Error
Second (SES) to be counted.
Object MAY be changed when the related P… | column | Percent SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.20.13.1.3.1.17 |
| pwTDMCfgTimestampMode Timestamp generation MAY be used in one of the following
modes:
1. Absolute mode: the PSN-bound IWF sets timestamps
using the clock recovered from the incoming TDM attachment… | column | Enumeration | .1.3.6.1.4.1.164.20.13.1.3.1.18 |
| pwTDMCfgStorageType This variable indicates the storage type for this
row. | column | SNMPv2-TCStorageType | .1.3.6.1.4.1.164.20.13.1.3.1.19 |
| pwTDMCfgRowStatus Object used for creating, modifying, and deleting
a row from this table. The following objects should not be
modified if the entry is in used and the status is active:
pwTDMCfgP… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.164.20.13.1.3.1.2 |
| pwTDMCfgPktFiller Filler byte pattern played out on the TDM
interface if pwTDMCfgPktReplacePolicy
was set to filler(3).
Object MAY be changed when the related PW is
defined as not active. | column | Unsigned32 | .1.3.6.1.4.1.164.20.13.1.3.1.20 |
| pwTDMCfgName A descriptive string, prefereably unique name, to an entry
in this table.
Object MAY be changed at any time. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.164.20.13.1.3.1.21 |
| pwTDMCfgConfErr deprecated Various configuration errors. Illegal settings within
the pwTDMCfg table. Setting is done based
on signaling, or else value (0) will be set | column | Bits | .1.3.6.1.4.1.164.20.13.1.3.1.3 |
| pwTDMCfgPayloadSize The value of this object indicates the PayLoad Size (in bytes)
to be defined during the PW setUp. Upon TX, implementation
must be capable of carrying that amount of bytes.
Upon… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.20.13.1.3.1.4 |
| pwTDMCfgPktReorder If set True: as CE bound packets are queued in the
jitter buffer, out of order packets are re-ordered. The
maximum sequence number differential (i.e., the range in
which re-se… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.164.20.13.1.3.1.5 |
| pwTDMCfgRtpHdrUsed If set to False: an RTP header is not pre-pended to the
TDM packet. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.164.20.13.1.3.1.6 |
| pwTDMCfgJtrBfrDepth The size of this buffer SHOULD be locally
configured to allow accommodation to the PSN-specific packet
delay variation.
If configured to a value not supporte… | column | microsecond SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.20.13.1.3.1.7 |
| pwTDMCfgPayloadSuppression Selecting 'enable' means: Payload suppression is allowed.
Payload MAY be omitted in order to conserve bandwidth.
Selecting 'disable' means: no suppresion under any
condition.
Ob… | column | Enumeration | .1.3.6.1.4.1.164.20.13.1.3.1.8 |
| pwTDMCfgConsecPktsInSynch The number of consecutive packets with sequential
sequence numbers that are required to exit the
LOPS state.
Object MAY be changed when the related PW is
defined as not active. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.164.20.13.1.3.1.9 |