DASAN-SHDSL-MIB Table View

This object identifies the high level operational state for the STU.

This object identifies the current detailed operational state of the STU.

Transceiver firmware release number.

This object indicates if the physical lines are swapped, i.e., logical channel A is connected to physical channel B. This applies to 4-wire operation only.

This object provides the country code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop. GlobespanVirata sets this to USA.

This object identifies the 21-bit value corresponding to encoder coefficient A, as defined in ITU-T G.991.2, for the STU at the other end of the loop.

This object identifies the 21-bit value corresponding to encoder coefficient B, as defined in ITU-T G.991.2, for the STU at the other end of the loop.

This object identifies the provider code word, as defined in ITU-T G.991.2, for the STU at the other end of the loop.

This object is used to determine if carrier has been lost.

This object identifies the local STU transmit power in tenths of a dBm.

This object returns information regarding the framer synchronization status.

This object provides vendor-provided data, as defined in ITU-T G.991.2, for the STU at the other end of the loop.

This object identifies if the receive clock is in or out of range.

This object provides the total receiver gain in dB.

This object provides the count of bit errors since the last time the object was read, as well as the type of synchronization.

This object returns overhead data. The four least significant bits contain the overhead data in the following format: bit 0 is losd, bit 1 is sega, bit 2 is ps, and bit 3 is segd.

This object provides the transceiver firmware release number of the STU at the other end of the loop.

This object indicates whether cell delineation has been found.

This object indicates the number of UTOPIA cells received since the last time the object has been called. The maximum value is 0xFFFF.

This object indicates the number of UTOPIA cells dropped since the last time the object has been called. The maximum value is 0xFF.

This object indicates the number of UTOPIA cells with HEC errors since the last time the object has been called. The maximum value is 0xFF.

This object indicates the number of UTOPIA cells transmitted since the last time the object has been called. The maximum value is 0xFFFF.

This object returns the customer identification that was sent by the STU at the other end of the loop.

This object returns non-standard format customer data that was sent by the STU at the other end of the loop.

This object provides a way to see what capabilities are supported by the local STU. A total of 26 handshake parameters are supported.

This object provides a way to see what capabilities are supported by the STU at the other end of the loop. A total of 26 handshake parameters are supported.

This object provides the results of capabilities exchanged during handshake. A total of 26 handshake parameters are supported.

This object provides the transmit power of the STU at the other end of the loop.

This object indicates whether power backoff is enabled or disabled at the STU at the other end of the loop.

This object indicates the number of automatic retrains. This counter is only reset when a startup is initiated.

This object provides status information about the eoc stage.

This object provides CRC, SEGA, and LOSW defect one second error counts, and should be called every second.

This object identifies the Network Timing Recovery Fault.

Indicates the Result of the Parametric Test conducted on the Xcvr.

Conexant parameter that indicates the Parametric Test Array.

This object specifies actions that are used to control transceiver operation.

This object specifies the operational mode of the transceiver.

This object is used to compensate for minor differences in transmit power between designs.

This object defines which type of data interface type is used. Note that the non-default values only apply to Conexant chips that support serial interfaces.

This objects defines which AFE is being used.

This object determines the value of encoder coefficient A, as defined in ITU-T G.991.2.

This object determines the value of encoder coefficient B, as defined in ITU-T G.991.2

This object determines the number of bytes of EOC data that is buffered by the DSP in the transmit direction.

This object determines the number of bytes of EOC data that is buffered by the DSP in the receive direction.

This object defines how network-timing recovery is performed.

Customer-defined value. This object defines the upstream frame sync word.

This object defines the downstream frame sync word.

Customer-defined value. This object defines the upstream.

This object defines the downstream stuff bits.

This object defines which STU initiates a startup. The default is STU-R initiates and STU-C waits.

This object determines the source of the receive clock.

This object enables or disables the internal PLL.

This object enables the user to set the size of the framer buffer for serial ATM operation.

This object selects the appropriate UTOPIA Level 2 address for the transmit interface.

This object selects the appropriate UTOPIA Level 2 address for the receive interface.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the transmit frame pulse.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be specified for the receive frame pulse.

This object specifies the multi frame operational mode of the transceiver.

This object specifies the operational state of the 4_6Mbps bit rate.

This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.

This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.

This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.

This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.

This object enables a silent mode for the STU at the opposite end of the loop for approximately one minute. During the silent period, the STU that requested the silent mode could perform whatever operations it wants and…

This item enables the user to individually enable or disable base rates for N=1 through N=16. The default is all rates enabled.

This item enables the user to individually enable or disable base rates for N=17 through N=32. The default is all rates enabled.

This item enables the user to individually enable or disable base rates for N=33 through N=36. The default is all rates enabled.

This object enables the user to enable or disable cell delineation for serial ATM operation. This parameter should be set before a startup.

This object determines whether cells are dropped, i.e., not passed to the host, or not dropped, i.e., passed to the host. This object must be set prior to startup.

This object specifies the Gear Shift Type.

This object enables or disables nonstandard Information fields for MP, MS, CL, and CLR messages, as defined in ITU-T G.994.1.bis.

This object specifies the maximum bit per baud.

This object identifies the customer identification during handshaking, as described in ITU-T G.994.1.bis.

This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.

This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.

This object allows the customer to choose between support for Annex B, Annex B with Access Network Frequency Plan (ANFP), or both.

Enables or disables auto-retrain.

Enables or disables auto-retrain based on CRC errors.

Enables or disables auto-retrain based on framer synchronization.

Enables or disables auto-retrain based on whether the S/N margin falls below a preset threshold.

Sets the threshold for the number of frames with CRC errors for autoretrain.

Set the margin threshold for autoretrain.

Sets the time over which the autoretrain parameters must be outside their normal ranges, so that an auto-retrain occurs.

Enables/disables trap indicating a change in op state.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, transmit data can be sampled upon either rising or falling edge of the transmit …

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, receive data can be valid upon either rising or falling edge of the receive cloc…

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active upon either rising or falling edge.

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).

This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either active high (1) or active low (0).

This parameter is used to specify width of UTOPIA data bus.

This object specifies framer OverHead Channel.

This Parameter enables or disables the Trap for Loop Attenuation Threshold crossing.

This Parameter enables or disables the Trap for SNR Margin Threshold crossing.

This Parameter enables or disables the Trap for Framer Overhead and Defects.

Indicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified.

Indicates Start bin for range of bins to be measured. The default value mentioned is an indicative value only, for exact value refer to document number DO-400523-AN and DO-401163-AN.

Indicates End bin for range of bins to be measured. The default value mentioned is an indicative value only.

This object provides the maximum PMMS rate the line is capable of achieving

Contains the current 4 Wire Handshake Mode Configured