dsShdslParamHybridLossTestEnd

DASAN-SHDSL-MIB · .1.3.6.1.4.1.6296.9.6.1.1.3.1.63
MIB view Table view

Object

column r/w Integer32 
Indicates End bin for range of bins to be measured.  The default value mentioned is an indicative value only.

Context

MIB
DASAN-SHDSL-MIB
OID
.1.3.6.1.4.1.6296.9.6.1.1.3.1.63
Type
column
Access
readwrite
Status
current
Parent
dsShdslLineParamsEntry
Table
dsShdslLineParamsTable
Siblings
62

Syntax

Integer32

Values & Constraints

Object Constraints
range: 0-255

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
dsShdslAction
This object specifies actions that are used to control transceiver operation.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.1
dsShdslNTR
This object defines how network-timing recovery is performed.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.10
dsShdslRxUpstreamFrameSync
Customer-defined value. This object defines the upstream frame sync word.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.11
dsShdslRxDownstreamFrameSync
This object defines the downstream frame sync word.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.12
dsShdslRxUpstreamStuffBits
Customer-defined value. This object defines the upstream.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.13
dsShdslRxDownstreamStuffBits
This object defines the downstream stuff bits.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.14
dsShdslInitiate
This object defines which STU initiates a startup. The default is STU-R initiates and STU-C waits.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.15
dsShdslFramerRxClockMode
This object determines the source of the receive clock.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.16
dsShdslFramerRxPllMode
This object enables or disables the internal PLL.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.17
dsShdslSerialAtmCiuBufferSize
This object enables the user to set the size of the framer buffer for serial ATM operation.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.18
dsShdslUtopiaL2TxAddress
This object selects the appropriate UTOPIA Level 2 address for the transmit interface.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.19
dsShdslMode
This object specifies the operational mode of the transceiver.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.2
dsShdslUtopiaL2RxAddress
This object selects the appropriate UTOPIA Level 2 address for the receive interface.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.20
dsShdslTxFramerPulseDelay
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be s…
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.21
dsShdslRxFramerPulseDelay
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be s…
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.22
dsShdslMultiFrameMode
This object specifies the multi frame operational mode of the transceiver.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.23
dsShdslEnable4or6MbpsBitrate
This object specifies the operational state of the 4_6Mbps bit rate.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.24
dsShdslTomDataWord1
This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.25
dsShdslTomDataWord2
This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.26
dsShdslTomDataWord3
This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.27
dsShdslTomDataWord4
This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.28
dsShdslSetReqSilenceMode
This object enables a silent mode for the STU at the opposite end of the loop for approximately one minute. During the silent period, the STU that requested the silent mode could …
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.29
dsShdslPowerScale
This object is used to compensate for minor differences in transmit power between designs.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.3
dsShdslSetIndividualRates1
This item enables the user to individually enable or disable base rates for N=1 through N=16. The default is all rates enabled.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.30
dsShdslSetIndividualRates2
This item enables the user to individually enable or disable base rates for N=17 through N=32. The default is all rates enabled.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.31
dsShdslSetIndividualRates3
This item enables the user to individually enable or disable base rates for N=33 through N=36. The default is all rates enabled.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.32
dsShdslSatmCellDelineation
This object enables the user to enable or disable cell delineation for serial ATM operation. This parameter should be set before a startup.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.33
dsShdslFramerCellDropOnError
This object determines whether cells are dropped, i.e., not passed to the host, or not dropped, i.e., passed to the host. This object must be set prior to startup.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.34
dsShdslGearShiftType
This object specifies the Gear Shift Type.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.35
dsShdslHsNsf
This object enables or disables nonstandard Information fields for MP, MS, CL, and CLR messages, as defined in ITU-T G.994.1.bis.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.36
dsShdslHsMaxBitsPerBaud
This object specifies the maximum bit per baud.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.37
dsShdslHsCusId
This object identifies the customer identification during handshaking, as described in ITU-T G.994.1.bis.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.38
dsShdslHsCusData0
This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.39
dsShdslFramerType
This object defines which type of data interface type is used. Note that the non-default values only apply to Conexant chips that support serial interfaces.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.4
dsShdslHsCusData1
This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis.
columnSNMPv2-SMIInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.40
dsShdslHsAnnexBType
This object allows the customer to choose between support for Annex B, Annex B with Access Network Frequency Plan (ANFP), or both.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.41
dsShdslAutoRetrain
Enables or disables auto-retrain.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.42
dsShdslArCrcCheck
Enables or disables auto-retrain based on CRC errors.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.43
dsShdslArFramerSyncCheck
Enables or disables auto-retrain based on framer synchronization.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.44
dsShdslArSnrMarginCheck
Enables or disables auto-retrain based on whether the S/N margin falls below a preset threshold.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.45
dsShdslArCrcThreshold
Sets the threshold for the number of frames with CRC errors for autoretrain.
columnInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.46
dsShdslArSnrMarginThreshold
Set the margin threshold for autoretrain.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.47
dsShdslArRetrainTime
Sets the time over which the autoretrain parameters must be outside their normal ranges, so that an auto-retrain occurs.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.48
dsShdslOpStateTrapEnable
Enables/disables trap indicating a change in op state.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.49
dsShdslAFEType
This objects defines which AFE is being used.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.5
dsShdslTxFrmrDataClkEdge
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, transmit data can be sampled upon either…
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.50
dsShdslRxFrmrDataClkEdge
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, receive data can be valid upon either ri…
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.51
dsShdslTxFrmrPulseClkEdge
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active u…
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.52
dsShdslRxFrmrPulseClkEdge
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active u…
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.53
dsShdslTxFrmrPulseLvl
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either a…
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.54
dsShdslRxFrmrPulseLvl
This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either a…
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.55
dsShdslUtopiaDataBusWidth
This parameter is used to specify width of UTOPIA data bus.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.56
dsShdslFrmrOH
This object specifies framer OverHead Channel.
columnInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.57
dsShdslLoopAttenCrossingTrapEnable
This Parameter enables or disables the Trap for Loop Attenuation Threshold crossing.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.58
dsShdslSNRMarginCrossingTrapEnable
This Parameter enables or disables the Trap for SNR Margin Threshold crossing.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.59
dsShdslEncodeCoeffA
This object determines the value of encoder coefficient A, as defined in ITU-T G.991.2.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.6
dsShdslFramerOHAndDefectsTrapEnable
This Parameter enables or disables the Trap for Framer Overhead and Defects.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.60
dsShdslParametricTestInputFile
Indicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified.
columnOctetString.1.3.6.1.4.1.6296.9.6.1.1.3.1.61
dsShdslParamHybridLossTestStart
Indicates Start bin for range of bins to be measured. The default value mentioned is an indicative value only, for exact value refer to document number DO-400523-AN and DO-401163-…
columnInteger32.1.3.6.1.4.1.6296.9.6.1.1.3.1.62
dsShdslEncodeCoeffB
This object determines the value of encoder coefficient B, as defined in ITU-T G.991.2
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.7
dsShdslTxEOCBufferLen
This object determines the number of bytes of EOC data that is buffered by the DSP in the transmit direction.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.8
dsShdslRxEOCBufferLen
This object determines the number of bytes of EOC data that is buffered by the DSP in the receive direction.
columnEnumeration.1.3.6.1.4.1.6296.9.6.1.1.3.1.9