dsShdslOpStateTrapEnable
DASAN-SHDSL-MIB ·
.1.3.6.1.4.1.6296.9.6.1.1.3.1.49
Object
column
r/w
Enumeration
Enables/disables trap indicating a change in op state.
Context
- MIB
- DASAN-SHDSL-MIB
- OID
.1.3.6.1.4.1.6296.9.6.1.1.3.1.49- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- dsShdslLineParamsEntry
- Table
- dsShdslLineParamsTable
- Siblings
- 62
Syntax
Enumeration
Values & Constraints
Enumerated Values
1 | enable |
2 | disable |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| dsShdslAction This object specifies actions that are used to control transceiver operation. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.1 |
| dsShdslNTR This object defines how network-timing recovery is performed. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.10 |
| dsShdslRxUpstreamFrameSync Customer-defined value. This object defines the upstream frame sync word. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.11 |
| dsShdslRxDownstreamFrameSync This object defines the downstream frame sync word. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.12 |
| dsShdslRxUpstreamStuffBits Customer-defined value. This object defines the upstream. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.13 |
| dsShdslRxDownstreamStuffBits This object defines the downstream stuff bits. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.14 |
| dsShdslInitiate This object defines which STU initiates a startup. The default is STU-R initiates and STU-C waits. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.15 |
| dsShdslFramerRxClockMode This object determines the source of the receive clock. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.16 |
| dsShdslFramerRxPllMode This object enables or disables the internal PLL. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.17 |
| dsShdslSerialAtmCiuBufferSize This object enables the user to set the size of the framer buffer for serial ATM operation. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.18 |
| dsShdslUtopiaL2TxAddress This object selects the appropriate UTOPIA Level 2 address for the transmit interface. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.19 |
| dsShdslMode This object specifies the operational mode of the transceiver. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.2 |
| dsShdslUtopiaL2RxAddress This object selects the appropriate UTOPIA Level 2 address for the receive interface. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.20 |
| dsShdslTxFramerPulseDelay This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be s… | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.21 |
| dsShdslRxFramerPulseDelay This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, a delay of up to 7 clock cycles can be s… | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.22 |
| dsShdslMultiFrameMode This object specifies the multi frame operational mode of the transceiver. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.23 |
| dsShdslEnable4or6MbpsBitrate This object specifies the operational state of the 4_6Mbps bit rate. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.24 |
| dsShdslTomDataWord1 This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.25 |
| dsShdslTomDataWord2 This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.26 |
| dsShdslTomDataWord3 This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.27 |
| dsShdslTomDataWord4 This object identifies one of four words of proprietary vendor data, as described in the Vendor Data section of ITU-T G.994.1.bis. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.28 |
| dsShdslSetReqSilenceMode This object enables a silent mode for the STU at the opposite end of the loop for approximately one minute. During the silent period, the STU that requested the silent mode could … | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.29 |
| dsShdslPowerScale This object is used to compensate for minor differences in transmit power between designs. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.3 |
| dsShdslSetIndividualRates1 This item enables the user to individually enable or disable base rates for N=1 through N=16. The default is all rates enabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.30 |
| dsShdslSetIndividualRates2 This item enables the user to individually enable or disable base rates for N=17 through N=32. The default is all rates enabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.31 |
| dsShdslSetIndividualRates3 This item enables the user to individually enable or disable base rates for N=33 through N=36. The default is all rates enabled. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.32 |
| dsShdslSatmCellDelineation This object enables the user to enable or disable cell delineation for serial ATM operation. This parameter should be set before a startup. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.33 |
| dsShdslFramerCellDropOnError This object determines whether cells are dropped, i.e., not passed to the host, or not dropped, i.e., passed to the host. This object must be set prior to startup. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.34 |
| dsShdslGearShiftType This object specifies the Gear Shift Type. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.35 |
| dsShdslHsNsf This object enables or disables nonstandard Information fields for MP, MS, CL, and CLR messages, as defined in ITU-T G.994.1.bis. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.36 |
| dsShdslHsMaxBitsPerBaud This object specifies the maximum bit per baud. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.37 |
| dsShdslHsCusId This object identifies the customer identification during handshaking, as described in ITU-T G.994.1.bis. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.38 |
| dsShdslHsCusData0 This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.39 |
| dsShdslFramerType This object defines which type of data interface type is used. Note that the non-default values only apply to Conexant chips that support serial interfaces. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.4 |
| dsShdslHsCusData1 This object identifies two words of customer data during handshaking, as defined in ITU-T G.994.1.bis. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.40 |
| dsShdslHsAnnexBType This object allows the customer to choose between support for Annex B, Annex B with Access Network Frequency Plan (ANFP), or both. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.41 |
| dsShdslAutoRetrain Enables or disables auto-retrain. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.42 |
| dsShdslArCrcCheck Enables or disables auto-retrain based on CRC errors. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.43 |
| dsShdslArFramerSyncCheck Enables or disables auto-retrain based on framer synchronization. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.44 |
| dsShdslArSnrMarginCheck Enables or disables auto-retrain based on whether the S/N margin falls below a preset threshold. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.45 |
| dsShdslArCrcThreshold Sets the threshold for the number of frames with CRC errors for autoretrain. | column | Integer32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.46 |
| dsShdslArSnrMarginThreshold Set the margin threshold for autoretrain. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.47 |
| dsShdslArRetrainTime Sets the time over which the autoretrain parameters must be outside their normal ranges, so that an auto-retrain occurs. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.48 |
| dsShdslAFEType This objects defines which AFE is being used. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.5 |
| dsShdslTxFrmrDataClkEdge This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, transmit data can be sampled upon either… | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.50 |
| dsShdslRxFrmrDataClkEdge This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, receive data can be valid upon either ri… | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.51 |
| dsShdslTxFrmrPulseClkEdge This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active u… | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.52 |
| dsShdslRxFrmrPulseClkEdge This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be active u… | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.53 |
| dsShdslTxFrmrPulseLvl This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either a… | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.54 |
| dsShdslRxFrmrPulseLvl This parameter is for Serial ATM applications only. It is recommended that the default value be used. For special customer configurations, the transmit frame pulse can be either a… | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.55 |
| dsShdslUtopiaDataBusWidth This parameter is used to specify width of UTOPIA data bus. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.56 |
| dsShdslFrmrOH This object specifies framer OverHead Channel. | column | Integer32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.57 |
| dsShdslLoopAttenCrossingTrapEnable This Parameter enables or disables the Trap for Loop Attenuation Threshold crossing. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.58 |
| dsShdslSNRMarginCrossingTrapEnable This Parameter enables or disables the Trap for SNR Margin Threshold crossing. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.59 |
| dsShdslEncodeCoeffA This object determines the value of encoder coefficient A, as defined in ITU-T G.991.2. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.6 |
| dsShdslFramerOHAndDefectsTrapEnable This Parameter enables or disables the Trap for Framer Overhead and Defects. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.60 |
| dsShdslParametricTestInputFile Indicates Name of the Input file from which to take the Mask Array Size, lower and upper mask Array. Null string means no file is specified. | column | OctetString | .1.3.6.1.4.1.6296.9.6.1.1.3.1.61 |
| dsShdslParamHybridLossTestStart Indicates Start bin for range of bins to be measured. The default value mentioned is an indicative value only, for exact value refer to document number DO-400523-AN and DO-401163-… | column | Integer32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.62 |
| dsShdslParamHybridLossTestEnd Indicates End bin for range of bins to be measured. The default value mentioned is an indicative value only. | column | Integer32 | .1.3.6.1.4.1.6296.9.6.1.1.3.1.63 |
| dsShdslEncodeCoeffB This object determines the value of encoder coefficient B, as defined in ITU-T G.991.2 | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.7 |
| dsShdslTxEOCBufferLen This object determines the number of bytes of EOC data that is buffered by the DSP in the transmit direction. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.8 |
| dsShdslRxEOCBufferLen This object determines the number of bytes of EOC data that is buffered by the DSP in the receive direction. | column | Enumeration | .1.3.6.1.4.1.6296.9.6.1.1.3.1.9 |