CISCO-VISM-DSX0-MIB Table View

The entries in this table are created and deleted 
implicitly at the time of adding and deleting the line.
For every DS0 on a line, one row will be created.

dsx0VismCnfEntry row .1.3.6.1.4.1.351.110.4.7.1.1

This ds0 table contains both cas related
and non cas related parameters.

The non cas related parameters are applicable
accross all line signaling types, while the
following cas related parameters
are applic…

Indexes

ds0IfIndex

Column	Syntax	OID
ds0IfIndex This attribute defines the index for this table. This is derived from the following formula: index = 31 * (Ds1# - 1) + ds0# where : Ds1# - The T1/E1 line number in the range 1 - 8. ds0# - …	Integer32 Constraints: range: 1-248	.1.3.6.1.4.1.351.110.4.7.1.1.1
ds0RobbedBitSignalling This object indicates if Robbed Bit Signalling is turned on or off for a given ds0. This only applies to DS0s on a DS1 link. For E1 links the value is always off (false). For T1 links, the default value is true if th…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.351.110.4.7.1.1.2
ds0IdleCode This object contains the code transmitted in the ABCD bits when the ds0 is not connected and ds0TransmitCodesEnable is enabled. The object is a bitmap and the various bit positions are: Bit 0 (value 1) D bit …	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.351.110.4.7.1.1.3
ds0SeizedCode This object contains the code transmitted in the ABCD bits when the ds0 is connected and ds0TransmitCodesEnable is enabled. The object is a bitmap and the various bit positions are: Bit 0 (value 1) D bit Bit …	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.351.110.4.7.1.1.4
ds0ReceivedCode This object contains the code being received in the ABCD bits. The object is a bitmap and the various bit positions are: Bit 0 (value 1) D bit Bit 1 (value 2) C bit Bit 2 (value 4) B bit …	Integer32 Constraints: range: 0-15	.1.3.6.1.4.1.351.110.4.7.1.1.5
ds0TransmitCodesEnabledeprecated This object determines if the idle and seized codes are transmitted. If the value of this object is true then the codes are transmitted. This object is not applicable in the CAS backhaul application.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.351.110.4.7.1.1.6
ds0BundleMapped This object indicates endpoint number as specified by mgEndpointNumber of endpoint table. If it is not associated with any endpoint, then it is set to -1. It should be noted that the endpoint is associated with bearer …	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.351.110.4.7.1.1.7
ds0IfType This object indicates the interface type associated with the ds0. bearer(81) : ds0 ifType is considered as bearer if the DS0 is used for carrying voice traffic. ccs-signaling(63): ds0 ifType is considered a…	Enumeration Enumerated Values: 1 unknown 63 ccs-signaling 81 bearer	.1.3.6.1.4.1.351.110.4.7.1.1.8
ds0CasVariantName This object indicates the index to the CAS variant table. This parameter can be configured after configuring this ds0 as an endpoint. This object cannot be modified while connections exist on this endpoint. The CAS var…	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.351.110.4.7.1.1.9
ds0CasCadenceOnTime This attribute describes the duration during which the digit tone is generated. This object is applicable only for CAS backhaul applications. For trunking application it is not applicable. The value is expresssed in un…	Integer32r/w Constraints: range: 2-9999	.1.3.6.1.4.1.351.110.4.7.1.1.10
ds0CasCadenceOffTime This attribute corresponds to the silence between the digit tones. This object is applicable only for CAS backhaul applications. For trunking application it is not applicable. The value is expresssed in units of millis…	Integer32r/w Constraints: range: 0-9999	.1.3.6.1.4.1.351.110.4.7.1.1.11
ds0InsertLocalCas This object tells the framer whether to force the cas bits to a value defined by ds0LocalCasPattern or not. If this is enabled the framer will force the cas (ABCD) bits to a value defined in ds0LocalC…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.351.110.4.7.1.1.12
ds0LocalCasPattern This object contains the pattern that the cas (ABCD) bits will have when ds0InsertLocalCas is enabled.	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.351.110.4.7.1.1.13
ds0LoopbackCommand This object represents the loopback type at the ds0 level.The ds0 configuration overrides the line level configuration. NoLoop There is no loopback on this ds0. LocalLoop …	Enumerationr/w Enumerated Values: 1 noLoop 2 remoteLoop 3 localLoop	.1.3.6.1.4.1.351.110.4.7.1.1.14
ds0CasParameterSource This object indicates VISM whether to read the cas related timer parameters from the casAppl file downloaded for that endpoint or to read from this mib. This gives the flexibility of configuring differ…	Enumerationr/w Enumerated Values: 1 casAppl 2 mibValue	.1.3.6.1.4.1.351.110.4.7.1.1.15
ds0CasOnHookMinMakeTime This indicates the the minimum time in msecs for which the on hook pattern should be present in order for it to be recognised else the signal will be considered to be a spurious signal and will be ignored. …	millisecondsInteger32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.351.110.4.7.1.1.16
ds0CasOffHookMinMakeTime This indicates the minimum time in msecs for which the off hook pattern should be present in order for it to be recognised else the signal will be considered to be a spurious signal and will be ignored. …	millisecondsInteger32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.351.110.4.7.1.1.17
ds0CasWinkMinMakeTime The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the minimum duration for which the off-hook part of wink signal should persist. …	millisecondsInteger32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.351.110.4.7.1.1.18
ds0CasWinkMaxMakeTime The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the maximum duration for which the off-hook part of the wink signal should persist, if it exc…	millisescondsInteger32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.351.110.4.7.1.1.19
ds0CasWinkBreakTime The wink consists of off-hook A-B bit pattern, followed by on-hook A-B bit pattern in timed sequence. This object indicates the minimum duration for which the on-hook part of wink signal should persist. …	millisecondsInteger32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.351.110.4.7.1.1.20
ds0CasGlareTime When the terminating gateway receives off Hook event from the Call Agent it starts the timer specified in this object to see if the terminating side is also trying to originate a call. If this is true, we have a 'glare…	millisecondsInteger32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.351.110.4.7.1.1.21
ds0CasGaurdTime The gaurd time is the duration between the end of one call and the start of next call. This object specifies what should be such a duration. All state changes from the PBX are ignored for this duration. After receiving…	millisecondsInteger32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.351.110.4.7.1.1.22
ds0CasDelayImmedStart This timer indicates the time that VISM should wait before outpulsing digits to the PBX after sending an off hook event. This applies only to immediate start protocol. This object cannot be configured i…	millisecondsInteger32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.351.110.4.7.1.1.23
ds0SignalingType This attribute indicates the type of signaling on the line to which this ds0 belongs. CAS - Channel Associated Signaling CCS - Common Channel Signaling none - no signaling used. This …	Enumeration Enumerated Values: 1 cas 2 ccs 3 none	.1.3.6.1.4.1.351.110.4.7.1.1.24
ds0CasMinDelayDialTime This is an object for an E & M signaling protocol like wink-start for this ds0. The difference is that the address-control signal is different from wink. The originating VISM, on receiving a seize (AB=11) from the P…	millisecondsSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.351.110.4.7.1.1.25
ds0CasMinStartDialTime This is an object for an E & M signaling protocol like wink-start for this ds0. The difference is that the address-control signal is different from wink. The originating VISM, on receiving a seize (AB=11) from the P…	millisecondsSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.351.110.4.7.1.1.26
ds0CasFlashMinMakeTime Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an on-hook followed by an off-hook. This object specifies th…	millisecondsSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.351.110.4.7.1.1.27
ds0CasFlashMaxMakeTime Flash is a CAS signal generated by users to request special services. The interpretation of the flash depends on the protocol in use. The signal itself is an on-hook followed by an off-hook. This object specifies th…	millisecondsSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.351.110.4.7.1.1.28
ds0CasDirectionality This object specifies the direction in which CAS calls will be accepted on this endpoint. If this object is set to bidirectional(1): VISM can send and receive calls on this endpoint …	Enumerationr/w Enumerated Values: 1 bidirectional 2 incoming 3 outgoing	.1.3.6.1.4.1.351.110.4.7.1.1.29
ds0CasGlarePolicy This object specifies how a bidirectional endpoint should resolve glare. This object will be used only if dsx0VismDirectionality of the endpoint is 'bidirectional'. When glare is detected, if this object is set to cont…	Enumerationr/w Enumerated Values: 1 controlling 2 releasing	.1.3.6.1.4.1.351.110.4.7.1.1.30
ds0CasIncomingMgcpPackage This object, in conjunction with the card level persistentXgcpEventsTable, controls how persistent CAS events (like seize, disconnect, etc) related to an incoming call observed on this DS0 are notified to the Media…	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.351.110.4.7.1.1.31
ds0CasOutgoingMgcpPackage This object, in conjunction with the card level persistentXgcpEventsTable, controls how persistent CAS events (like answer, disconnect, etc) related to an outgoing call observed on this DS0 are notified to the Media…	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.351.110.4.7.1.1.32
ds0InputGain This object indicates the amount of gain inserted at the receiver side of a ds0 channel, in dB (decibel) units. The default value of this object is 0 dB. The input gain settings only define a gain/loss r…	dB - decibelInteger32r/w Constraints: range: -6-14	.1.3.6.1.4.1.351.110.4.7.1.1.33
ds0OutputAttenuation This object contains the amount of attenuation inserted at the transmit side of a ds0 channel, in dB (decibel) units. The output attenuation settings only define a loss relative to 0 dB setting. The abs…	dB - decibelInteger32r/w Constraints: range: 0-14	.1.3.6.1.4.1.351.110.4.7.1.1.34
ds0MusicThreshold The indicates Music On Hold Threshold in dBm. Based on this value, VISM DSP will interprete the incoming signal from TDM side as either silence or voice, and consequently turn on or off VAD. This object…	Integer32r/w Constraints: range: -70--30	.1.3.6.1.4.1.351.110.4.7.1.1.35
ds0SidPacket This object specifies whether the Silence Indication Detection (SID) packet should be generated when silence suppression is in active mode. The SID packet indicates the noise level during silence, which is used as a …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.351.110.4.7.1.1.36
ds0ExecDiag This object indicates the status of DSP channel level RAS on the VISM. When it is enable VISM will configure the DSP through HOST-DSP message on the individual channel.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.351.110.4.7.1.1.37
ds0Companding This object indicates whether input from / output to the TDM side of DS0 is u-law or a-law stream. The setting of this object will not take effect unless the corresponding DSP channel is closed and re-opened.	Enumerationr/w Enumerated Values: 1 uLaw 2 aLaw	.1.3.6.1.4.1.351.110.4.7.1.1.38
ds0RxCasTransTblName This object identifies the template name 'cvcmCasTemplateName' in the CISCO-VOICE-CAS-MODULE-MIB associated with the receive signaling channel on a DS0.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.351.110.4.7.1.1.39
ds0TxCasTransTblName This object identifies the template name 'cvcmCasTemplateName' in the CISCO-VOICE-CAS-MODULE-MIB associated with the transmit signaling channel on a DS0.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.351.110.4.7.1.1.40
ds0TxRxCasConfig This object indicates configuration on a DS0. 'transmit'- Configure transmit signaling channel on the DSP with user defined CAS pattern to translate incoming ABCD …	Enumerationr/w Enumerated Values: 1 transmit 2 receive 3 bidirectional 4 none	.1.3.6.1.4.1.351.110.4.7.1.1.41

This table is created implicitly at the time of 
creating and deleting the endpoints.
This table provides the mapping information from a line
and channel to obtain an index for that channel.

dsx0VismChanMapEntry row .1.3.6.1.4.1.351.110.4.7.2.1

Each entry represents the mapping from dsx1Line number
to ds0 channel Number and provides the ifIndex mapping.

Indexes

dsx1LineNum ds0ChanNum

Column	Syntax	OID
dsx1LineNum This object describes the physical line number on VISM card.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.351.110.4.7.2.1.1
ds0ChanNum This object describes the ds0 number or channel number within a T1 or E1 line. The valid channel numbers are 1 to 24 for T1 line and 1 - 31 for E1 line.	Integer32 Constraints: range: 1-31	.1.3.6.1.4.1.351.110.4.7.2.1.2
ds0ChanMapIfIndex This object describes the ifIndex derived based on the line number and the channel number within the line according to the formula: IfIndex = 31 * (Ds1# - 1) + ds0# where : Ds1# - The T1/E1 line number …	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.351.110.4.7.2.1.3

This table contains information on DS0s configured
on DS1 interface.

vismDs0LineStatsEntry row .1.3.6.1.4.1.351.110.4.7.3.1

An entry in the vismDs0LineStatsTable.
Each entry contains following information
applicable for each DS1 interface:
Total DS0s
Free DS0s
Active DS0s
Blocked DS0s.

Indexes

ds0LineNum

Column	Syntax	OID
ds0LineNum This object is the identifier of a DS1/E1 Interface on a managed device. The number of entries is 8 in a VISM and VISM-PR card.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.351.110.4.7.3.1.1
lineTotalDs0Count This is the total number of ds0s configured on this DS1 line.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.351.110.4.7.3.1.2
lineFreeDs0Count This is the total number of free ds0s on this DS1 line.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.351.110.4.7.3.1.3
lineActiveDs0Count This is the number of active ds0s on this line.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.351.110.4.7.3.1.4
lineBlockDs0Count This is the number of blocked ds0s on this line.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.351.110.4.7.3.1.5
lineActiveHighWaterMark This is the high water mark number of ds0s that were active simultaneously on the line.	Integer32 Constraints: range: 0-31	.1.3.6.1.4.1.351.110.4.7.3.1.6
lineStatsClrButton This variable is used to clear the vism Ds0 line status entry. 1 = No action, 2 = Clear alarm.	Enumerationr/w Enumerated Values: 1 noaction 2 clear	.1.3.6.1.4.1.351.110.4.7.3.1.7

This table contains ds0 status information on a
DS1 interface.

vismDs0StatusEntry row .1.3.6.1.4.1.351.110.4.7.4.1

An entry in the Ds0 Status Table.

Indexes

ds0LineNumber ds0Number

Column	Syntax	OID
ds0LineNumber This object is the identifier of a DS1/E1 Interface on a managed device. The number of entries is 8 in a VISM and VISM-PR card.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.351.110.4.7.4.1.1
ds0Number This object identifies the ds0 number on a DS1 interface.	Integer32 Constraints: range: 1-31	.1.3.6.1.4.1.351.110.4.7.4.1.2
ds0Status This object is the status of the ds0. idle - This ds0 is in idle state. busy - This ds0 is in busy state. Ds0 enters this state when it is in the process of being setup for a call. fault - This ds0 is in fault(alarm) …	Enumeration Enumerated Values: 1 idle 2 busy 3 fault 4 block 5 unknown	.1.3.6.1.4.1.351.110.4.7.4.1.3
ds0StatusClrButton This variable is used to clear the vism Ds0 status. 1 = No action, 2 = Clear alarm	Enumerationr/w Enumerated Values: 1 noaction 2 clear	.1.3.6.1.4.1.351.110.4.7.4.1.4