CISCO-ITP-DSMR-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
8
Rows
8
Columns
137

cdsmrInstTable

table
.1.3.6.1.4.1.9.9.1300.1.2 · 1 row entry · 26 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk cdsmrInstTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ITP-DSMR-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ITP-DSMR-MIB::cdsmrInstTable' 
A table that is used to provide information and measurements
related to Distributed Short Message Routing per signalling
point. Entries are added to this table via 
cdsmrInstRowStatus in accordance with the RowStatus 
convention.
cdsmrInstTableEntry row .1.3.6.1.4.1.9.9.1300.1.2.1
Each entry in this table provides information on each
signalling point supported by this device.
Indexes
Column Syntax OID
cdsmrInstLastChanged
The value of sysUpTime at the time of the last
creation or deletion of an entry in the Multi-Layer
configurations defined for this signalling point.
If the local network management subsystem is
re-initialized, then thi…
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
 .1.3.6.1.4.1.9.9.1300.1.2.1.1
cdsmrInstLastLoadTime
The value of sysUpTime at the time of the last load of
a file supporting Distributed Short Message Routing
for this signalling point.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
 .1.3.6.1.4.1.9.9.1300.1.2.1.2
cdsmrInstLoadStatus
The status of the current load or status from
the prior load operation. This object will have
a value of loadInProgress while the load operation
is in progress. The cdsmrInstLastLoadTime contains
a timestamp indicatin…
CISCO-ITP-TC-MIBCItpTcTableLoadStatus
Type Values:
1loadNotRequested
2loadInProgress
3loadComplete
4loadCompleteWithErrors
5loadFailed
 .1.3.6.1.4.1.9.9.1300.1.2.1.3
cdsmrInstLastURL
The last URL used to load a file used to configure
Distributed Short Message Routing.
CISCO-ITP-TC-MIBCItpTcURL
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.2.1.4
cdsmrInstDeliveredSmppCounts
Count of the number of times a packet was routed
using Short Message Peer-to-Peer protocol.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.5
cdsmrInstDeliveredUcpCounts
Count of the number of times a packet was routed
using Universal Computer Protocol(UCP).
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.6
cdsmrInstDeliveredGsmCounts
Count of the number of times a GSM packet was
delivered.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.7
cdsmrInstDeferredGsmCounts
Count of the number of times a GSM packet was
deferred.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.8
cdsmrInstGsmStatusReports
Count of the number GSM status reports issued by device.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.9
cdsmrInstUcpNotifications
Count of the number UCP notifications issued by device.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.10
cdsmrInstSmppDeliveryReceipts
Count of the number SMPP delivery receipts issued by
device.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.11
cdsmrInstRoutingFailures
Count of the number of times a packet could not be delivered
because route was not configured.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.12
cdsmrInstResultFailures
Count of the number of times processing of packet did not
produce valid result.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.13
cdsmrInstInternalErrors
Count of the number of times processing of packet was
not completed due to internal error.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.14
cdsmrInstParseErrors
Count of the number of times processing of packet was
not completed due to parsing error.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.15
cdsmrInstResourceErrors
Count of the number of times processing of packet was
not completed due to unavailable resources on device.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.16
cdsmrInstProvisioningErrors
Count of the number of times processing of packet was
not completed due to provisioning errors on device.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.17
cdsmrInstDestUnreachableErrors
Count of the number of times packet was not routed
because destination was unreachable.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.18
cdsmrInstDestSignalErrors
Count of the number of times packet was not routed
because destination had signal error.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.19
cdsmrInstTimeOuts
Count of the number of times packet was not delivered
due to timeout.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.20
cdsmrInstBlockedPackets
Count of the number of times packets were blocked
by processing.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.21
cdsmrInstRoutingRequestsRcvdGsm
Count of the number of routing requests received
were traffic was GSM based.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.22
cdsmrInstRoutingRequestsRcvdIs41
Count of the number of routing requests received
were traffic was IS-41 based.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.23
cdsmrInstRoutingRequestsRcvdUcp
Count of the number of routing requests received
were traffic was UCP based.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.24
cdsmrInstRoutingRequestsRcvdSmpp
Count of the number of routing requests received
were traffic was SMPP based.
packetsSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.2.1.25
cdsmrInstRowStatus
The object is used by a management station to
create or delete the row entry in cdsmrInstTable
following the RowStatus textual convention.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.9.9.1300.1.2.1.26

cdsmrResultGroupTable

table
.1.3.6.1.4.1.9.9.1300.1.3 · 1 row entry · 10 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk cdsmrResultGroupTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ITP-DSMR-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ITP-DSMR-MIB::cdsmrResultGroupTable' 
A table used to identify a group of results and define
parameter that apply to all result within the group.
Entries are added to this table via 
cdsmrResultGroupRowStatus  in accordance with the RowStatus
convention.
cdsmrResultGroupTableEntry row .1.3.6.1.4.1.9.9.1300.1.3.1
This table is used to define a collection of results.
Indexes
Column Syntax OID
cdsmrResultGroupName
A name used to define a result group.
CISCO-ITP-MLR-MIBCmlrName
Type Constraints:
range: 0..20
Description:
The configured name used to identify various
tables used by MLR.

An octet string specified by an administrator that
must be in human-readable form. The names must
conform to the allowed characters that can b…
 .1.3.6.1.4.1.9.9.1300.1.3.1.1
cdsmrResultGroupServerType
This object specifies the server type as follows.

'esme' - Indicates this result group represents an external
short message entity (ESME). Coding this parameter
will allow the user to …
Enumerationr/w
Enumerated Values:
1esme
2smsc
 .1.3.6.1.4.1.9.9.1300.1.3.1.2
cdsmrResultGroupCdrConsolidation
The object provides a one to five ASCII characters ESME
(large account) consolidation string. This object only
applies when the cdsmrResultGroupServerType object
specifies ESME. The object returns the null string
whe…
OctetStringr/w
Constraints:
range: 0-5
 .1.3.6.1.4.1.9.9.1300.1.3.1.3
cdsmrResultGroupIdentifier
The object provides a ESME (large account) identifier.
This object only applies when the cdsmrResultGroupServerType
object specifies ESME. The zero value is usedt to
indicate that the object has not been specified.
Unsigned32r/w
Constraints:
range: 0-0
range: 100-9999
 .1.3.6.1.4.1.9.9.1300.1.3.1.4
cdsmrResultGroupQueueLimit
This object defines the maximum number of elements on
outbound queue for any destination. The value of 0
indicates that there is no limit on the number of
entries.
Unsigned32r/w
Constraints:
range: 0-100000
 .1.3.6.1.4.1.9.9.1300.1.3.1.5
cdsmrResultGroupQueueTimeLimit
Maximum time element can exist in outbound queue.
millisecondsSNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.3.1.6
cdsmrResultGroupMatchSmppId
When specified this object provides 1 to 15 character
ESME system identifier. This object only applies when
the cdsmrResultGroupServerType object specifies ESME.
OctetStringr/w
Constraints:
range: 0-15
 .1.3.6.1.4.1.9.9.1300.1.3.1.7
cdsmrResultGroupMatchSmppType
When specified this object provides 1 to 12 character
ESME system type. This object only applies when the
cdsmrResultGroupServerType object specifies ESME.
When this object is not specified it will return the
null st…
OctetStringr/w
Constraints:
range: 0-12
 .1.3.6.1.4.1.9.9.1300.1.3.1.8
cdsmrResultGroupMatchUcpId
The object provides 1 to 16 character ESME
ESME UCP address code. This object only applies when
the cdsmrResultGroupServerType object specifies ESME.
OctetStringr/w
Constraints:
range: 0-16
 .1.3.6.1.4.1.9.9.1300.1.3.1.9
cdsmrResultGroupRowStatus
The object is used by a management station to
create or delete the row entry in cdsmrResultGroupTable
following the RowStatus textual convention.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.9.9.1300.1.3.1.10

cdsmrResultIpTable

table
.1.3.6.1.4.1.9.9.1300.1.4 · 1 row entry · 7 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk cdsmrResultIpTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ITP-DSMR-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ITP-DSMR-MIB::cdsmrResultIpTable' 
A table used to configure parameters to allow destination 
to be establish at request of partner. Entries are added
to this table via cdsmrResultIpRowStatus in accordance 
with the RowStatus convention.
cdsmrResultIpTableEntry row .1.3.6.1.4.1.9.9.1300.1.4.1
This table is used to define a list of IP addresses and
ports from which destination and establish connection.
Indexes
Column Syntax OID
cdsmrResultIpNumber
This object specifies the index for a list of results
specified per result group.
CISCO-ITP-MLR-MIBCmlrId
Type Constraints:
range: 0..65535
Description:
A numeric identifier used to specify an entry in a list.
Zero is a special value used to indicate no entry.
 .1.3.6.1.4.1.9.9.1300.1.4.1.1
cdsmrResultIpRemotePortNumber
Remote port number used to establish connection.
The value of zero indicates that any port number
will be accepted.
INET-ADDRESS-MIBInetPortNumberr/w
Type Constraints:
range: 0..65535
 .1.3.6.1.4.1.9.9.1300.1.4.1.2
cdsmrResultIpRemoteIpAddrType
This object contains the type of the remote
IP address used to create an session.
INET-ADDRESS-MIBInetAddressTyper/w
Type Values:
0unknown
1ipv4
2ipv6
3ipv4z
4ipv6z
16dns
25l2vpn
 .1.3.6.1.4.1.9.9.1300.1.4.1.3
cdsmrResultIpRemoteIpAddress
This object contains the remote IP address allowed
to request the session.
INET-ADDRESS-MIBInetAddressr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.4.1.4
cdsmrResultIpProfileName
The name of the profile used to specify parameter for
session as follows.

'smpp': cdsmrSmppProfileName
'ucp': cdsmrUcpProfileName

For all other values this object is ignored.
CISCO-ITP-MLR-MIBCmlrNamer/w
Type Constraints:
range: 0..20
Description:
The configured name used to identify various
tables used by MLR.

An octet string specified by an administrator that
must be in human-readable form. The names must
conform to the allowed characters that can b…
 .1.3.6.1.4.1.9.9.1300.1.4.1.5
cdsmrResultIpWeight
This object specifies the weight applied to the weighted
round robin distribution algorithm used for multi-layer
result group. An integer value in the range of 0 to 10.
A value of ten indicates the resource should …
Integer32r/w
Constraints:
range: 0-10
 .1.3.6.1.4.1.9.9.1300.1.4.1.6
cdsmrResultIpRowStatus
The object is used by a management station to
create or delete the row entry in cdsmrResultIpTable
following the RowStatus textual convention.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.9.9.1300.1.4.1.7

cdsmrResultTable

table
.1.3.6.1.4.1.9.9.1300.1.5 · 1 row entry · 15 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk cdsmrResultTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ITP-DSMR-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ITP-DSMR-MIB::cdsmrResultTable' 
A table used to configure parameters for destination 
resources. The result group lists the appropriate destination 
resources, and the mechanism used to select a single 
destination for a given packet.  State information is 
determined for each possible destination. Entries are 
added to this table via cdsmrResultRowStatus in accordance
with the RowStatus convention.
cdsmrResultTableEntry row .1.3.6.1.4.1.9.9.1300.1.5.1
This table is used to define a collection of
multi-layer routing statements.
Indexes
Column Syntax OID
cdsmrResultNumber
This object specifies the index for a list of results
specified per result group.
CISCO-ITP-MLR-MIBCmlrId
Type Constraints:
range: 0..65535
Description:
A numeric identifier used to specify an entry in a list.
Zero is a special value used to indicate no entry.
 .1.3.6.1.4.1.9.9.1300.1.5.1.1
cdsmrResultDestinationType
Destination type.
CdsmrResultDestinationTyper/w
Type Values:
1none
2gt
3smpp
4ucp
5pc
6pcSsn
 .1.3.6.1.4.1.9.9.1300.1.5.1.2
cdsmrResultParameters
Many of the result parameter used creating result are
optional. This object is used to indicate which
options are provided as follows.

'tranType' : cdsmrResultTransType
'gti' : cdsmrResultGti
'np…
CdsmrResultParametersr/w
Type Values:
0network
1octet
2tranType
3gti
4np
5nai
6pc
7ssn
8ruleNumber
 .1.3.6.1.4.1.9.9.1300.1.5.1.3
cdsmrResultDestinationName
The name of the destination as follows based on
cdsmrResultDestinationType:
'smpp': cdsmrSmppDestName
'ucp': cdsmrUcpDestName

For all other values this object is ignored.
CISCO-ITP-MLR-MIBCmlrNamer/w
Type Constraints:
range: 0..20
Description:
The configured name used to identify various
tables used by MLR.

An octet string specified by an administrator that
must be in human-readable form. The names must
conform to the allowed characters that can b…
 .1.3.6.1.4.1.9.9.1300.1.5.1.4
cdsmrResultPc
A destination point code that must exist in the MTP3
routing table, and its state is extracted from MTP3
for availability purposes. This object only has
applies when the cdsmrResultDestinationType object
has the 'pc…
CISCO-ITP-TC-MIBCItpTcPointCoder/w
Type Constraints:
range: 0..16777216
 .1.3.6.1.4.1.9.9.1300.1.5.1.5
cdsmrResultSsn
The subsystem number to be inserted into MSU. This
object only has applies when the cdsmrResultDestinationType
object has the 'pcSsn' value.
Otherwise, this object will return zero value.
CISCO-ITP-TC-MIBCItpTcSubSystemNumberr/w
Type Constraints:
range: 0
range: 2..255
 .1.3.6.1.4.1.9.9.1300.1.5.1.6
cdsmrResultGt
The global title address.

When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA clause of rule.

This object only…
CISCO-ITP-TC-MIBCItpTcGtaLongDisplayr/w
Type Constraints:
range: 0..64
 .1.3.6.1.4.1.9.9.1300.1.5.1.7
cdsmrResultTransType
The translation type specified within the address in the
message signal unit. This object only applies when the
CdsmrResultDestinationType is set to 'gt' value and
the 'tranType' bit is set in the cdsmrResultResultPa…
CISCO-ITP-GSCCP-MIBCgsccpGttTransTyper/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.5.1.8
cdsmrResultGti
The global title indicator value for the global tile address
specified within the message signal unit. This object only
applies when the CdsmrResultDestinationType is set to
'gt' value.
CISCO-ITP-GSCCP-MIBCgsccpGttGlobalTitleIndr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.5.1.9
cdsmrResultNp
The numbering plan for the global tile address specified
within the message signal unit. This object only applies
when the CdsmrResultDestinationType is set to 'gt' value.
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.5.1.10
cdsmrResultNai
The nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the cdsmrResultDestinationType is
set to 'gt' value.
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.5.1.11
cdsmrResultWeight
This object specifies the weight applied to the weighted
round robin distribution algorithm used for multi-layer
result group. An integer value in the range of 0 to 10.
A value of ten indicates the resource should …
Integer32r/w
Constraints:
range: 0-10
 .1.3.6.1.4.1.9.9.1300.1.5.1.12
cdsmrResultNetwork
The network name is used to indicate the network in which
the result operation will be performed.
CISCO-ITP-TC-MIBCItpTcNetworkNamer/w
Type Constraints:
range: 0..19
 .1.3.6.1.4.1.9.9.1300.1.5.1.13
cdsmrResultCounts
Number of times this entry was invoked.
matchesSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.5.1.14
cdsmrResultRowStatus
The object is used by a management station to
create or delete the row entry in cdsmrResultTable
following the RowStatus textual convention.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.9.9.1300.1.5.1.15

cdsmrAddressTable

table
.1.3.6.1.4.1.9.9.1300.1.6 · 1 row entry · 17 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk cdsmrAddressTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ITP-DSMR-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ITP-DSMR-MIB::cdsmrAddressTable' 
A table used to create a collection of addresses that
can be searched for exact or best matches. Entries are
added to this table via cdsmrAddressRowStatus in accordance 
with the RowStatus convention.
cdsmrAddressTableEntry row .1.3.6.1.4.1.9.9.1300.1.6.1
Each entry in the cdsmrAddressTable is used to search
for matches within a messages signalling unit.
Message signalling that match a particular rule can
be directed to cdsmrAddressTable to allow MSU to be
directed or m…
Indexes
Column Syntax OID
cdsmrAddressTableName
A name used to define a collection of addresses used to
route and modify messages signalling units.
CISCO-ITP-MLR-MIBCmlrName
Type Constraints:
range: 0..20
Description:
The configured name used to identify various
tables used by MLR.

An octet string specified by an administrator that
must be in human-readable form. The names must
conform to the allowed characters that can b…
 .1.3.6.1.4.1.9.9.1300.1.6.1.1
cdsmrAddressType
The type of addresses in the address tables.
The different types will be used to determine
how to format and convert cdsmrAddressDigits.
CISCO-ITP-MLR-MIBCmlrAddressType
Type Values:
1bch
2gsmDa
Description:
List of possible table types.

'bch' : Binary Coded Hexadecimal
'gsmDa' : GSM 7 bit Default Alphabet
 .1.3.6.1.4.1.9.9.1300.1.6.1.2
cdsmrAddressDigits
The digits of the address in following formats as
indicated by cdsmrAddressType object.
'hexadecimal' - The digits are hexadecimal digits specified
in ASCII as follows.
'0123456789ABC…
CISCO-ITP-MLR-MIBCmlrAddressDigits
Type Constraints:
range: 0..32
Description:
The configured digits of A-address or B-address
specified in the format indicated by CmlrAddressType.
All values are entered in binary and represent digits
All values are encoded as hexidecimal values and represent
the…
 .1.3.6.1.4.1.9.9.1300.1.6.1.3
cdsmrAddressExactMatch
This object indicates that the address specified by
cdsmrAddressDigits object must exactly match value
in message signalling unit.

'true' - Exact match is specified.
'false' - Best match is specified.
SNMPv2-TCTruthValue
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.9.9.1300.1.6.1.4
cdsmrAddressResultParameters
Many of the result parameter used in the processing of
address table have default values. These values are
determined by a combination of variant and operation
type. This object will be provide information which
param…
CdsmrResultParametersr/w
Type Values:
0network
1octet
2tranType
3gti
4np
5nai
6pc
7ssn
8ruleNumber
 .1.3.6.1.4.1.9.9.1300.1.6.1.5
cdsmrAddressResultNetwork
The network name is used to indicate the network in which
the result operation will be performed.
CISCO-ITP-TC-MIBCItpTcNetworkNamer/w
Type Constraints:
range: 0..19
 .1.3.6.1.4.1.9.9.1300.1.6.1.6
cdsmrAddressResultType
Specified the type of information to be placed into the
message signal unit or how the it will be processed.
CdsmrResultTyper/w
Type Values:
0none
1pc
2pcSsn
3gt
4group
5smpp
6ucp
7block
8ruleNext
9ruleNumber
10deliverMt
11origImsi
12origImsiNext
 .1.3.6.1.4.1.9.9.1300.1.6.1.7
cdsmrAddressResultOctet
Information to be placed in the message signal
unit based on the value specified by the
cdsmrAddressResultType object. When the
cdsmrAddressResultType object is set to
'group' or 'gt' this object will contain
the st…
CdsmrResultOctetr/w
Type Constraints:
range: 0..64
 .1.3.6.1.4.1.9.9.1300.1.6.1.8
cdsmrAddressResultTransType
The translation type specified within the address in the
message signal unit. This object only applies when the
cdsmrAddressResultType is set to 'gt' value and
the 'tranType' bit is set in the cdsmrAddressResultParam…
CISCO-ITP-GSCCP-MIBCgsccpGttTransTyper/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.6.1.9
cdsmrAddressResultGti
The global title indicator value for the global tile address
specified within the message signal unit. This object only
applies when the cdsmrAddressResultType is set to
'gt' value.
CISCO-ITP-GSCCP-MIBCgsccpGttGlobalTitleIndr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.6.1.10
cdsmrAddressResultNp
The numbering plan for the global tile address specified
within the message signal unit. This object only applies
when the cdsmrAddressResultType is set to 'gt' value.
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.6.1.11
cdsmrAddressResultNai
The nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the cdsmrAddressResultType is
set to 'gt' value.
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.6.1.12
cdsmrAddressResultPc
The point-code to be place in the message signal unit. This
object only applies when the cdsmrAddressResultType is set
to 'pc' value.
CISCO-ITP-TC-MIBCItpTcPointCoder/w
Type Constraints:
range: 0..16777216
 .1.3.6.1.4.1.9.9.1300.1.6.1.13
cdsmrAddressResultSsn
The subsystem number to be place in the message signal unit.
This object only applies when the cdsmrAddressResultType is set
to 'pcSsn' value.
CISCO-ITP-TC-MIBCItpTcSubSystemNumberr/w
Type Constraints:
range: 0
range: 2..255
 .1.3.6.1.4.1.9.9.1300.1.6.1.14
cdsmrAddressResultRuleNumber
Processing continues with rule number specified by this object.
This object only applies when the cdsmrAddressResultType is set
to 'ruleNumber' value.
CISCO-ITP-MLR-MIBCmlrIdr/w
Type Constraints:
range: 0..65535
Description:
A numeric identifier used to specify an entry in a list.
Zero is a special value used to indicate no entry.
 .1.3.6.1.4.1.9.9.1300.1.6.1.15
cdsmrAddressMatchCounts
Count of the number of times address was matched. This counter
is only incremented when rule matches.
matchesSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.6.1.16
cdsmrAddressRowStatus
The object is used by a management station to
create or delete the row entry in cdsmrAddressTable
following the RowStatus textual convention.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.9.9.1300.1.6.1.17

cdsmrRuleSetTable

table
.1.3.6.1.4.1.9.9.1300.1.7 · 1 row entry · 5 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk cdsmrRuleSetTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ITP-DSMR-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ITP-DSMR-MIB::cdsmrRuleSetTable' 
A table that is used to specify attributes of an
application-layer message to be matched and the resulting
behavior for handling the message. Entries are added to 
this table via cdsmrRuleSetRowStatus in accordance with 
the RowStatus convention.
cdsmrRuleSetTableEntry row .1.3.6.1.4.1.9.9.1300.1.7.1
Each entry in this table represents a set of addresses
used to perform non-standard routing of messages
signalling units..
Indexes
Column Syntax OID
cdsmrRuleSetName
A name used to define a set rules used to transform
traffic.
CISCO-ITP-MLR-MIBCmlrRuleSetName
Type Constraints:
range: 0..20
Description:
The configured name used to identify a set of rules
within an specified network.

An octet string specified by an administrator that
must be in human-readable form. The names must
conform to the allowed chara…
 .1.3.6.1.4.1.9.9.1300.1.7.1.1
cdsmrRuleSetProtocol
The object is used to establish a default protocol
type for all rules within the rule set. If this
object is set to 'none' will default to protocol
specified by variant.
CISCO-ITP-MLR-MIBCmlrRuleProtocolr/w
Type Values:
1none
2gsmMap
3ansi41
Description:
The list of possible protocol types.
'none' : Protocol not specified and will default to value
based on variant or other configuration
information.
'gsmMap' : Global system for mobile communica…
 .1.3.6.1.4.1.9.9.1300.1.7.1.2
cdsmrRuleSetStartDateAndTime
The local date and time when this trigger and sub-triggers
will become active. When the value is null then the
cdsmrInstStartDateAndTime does not apply.
SNMPv2-TCDateAndTimer/w
Type Constraints:
range: 8
range: 11
Description:
A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …
 .1.3.6.1.4.1.9.9.1300.1.7.1.3
cdsmrRuleSetEndDateAndTime
The local date and time this trigger and sub-triggers
will become inactive. When the value is null then the
cdsmrInstEndDateAndTime does not apply.
SNMPv2-TCDateAndTimer/w
Type Constraints:
range: 8
range: 11
Description:
A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …
 .1.3.6.1.4.1.9.9.1300.1.7.1.4
cdsmrRuleSetRowStatus
The object is used by a management station to
create or delete the row entry in cdsmrRuleSetTable
following the RowStatus textual convention.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.9.9.1300.1.7.1.5

cdsmrRuleTable

table
.1.3.6.1.4.1.9.9.1300.1.8 · 1 row entry · 54 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk cdsmrRuleTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ITP-DSMR-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ITP-DSMR-MIB::cdsmrRuleTable' 
A table that is used to specify attributes of an
application-layer message to be matched and the resulting
behavior for handling the message. Entries are added to 
this table via cdsmrRuleResultRowStatus in accordance 
with the RowStatus convention.
cdsmrRuleTableEntry row .1.3.6.1.4.1.9.9.1300.1.8.1
Entries in this table are searched in the specified order
defined by cdsmrRuleNumber object.
Indexes
Column Syntax OID
cdsmrRuleNumber
This object specifies the index for a list of secondary
triggers specified per routing table. The trigger will be
processed in ascending order.
CISCO-ITP-MLR-MIBCmlrId
Type Constraints:
range: 0..65535
Description:
A numeric identifier used to specify an entry in a list.
Zero is a special value used to indicate no entry.
 .1.3.6.1.4.1.9.9.1300.1.8.1.1
cdsmrRuleOperationType
The list of possible operation types.
'all' - All operations types.
'smdPp' - ANSI-41 Short message service delivery point
to point.
'smsMo' - GSM-MAP Short message service mobile
…
Enumerationr/w
Enumerated Values:
1all
2smdPp
3smsMo
4smsMt
5smsSri
6smsReg
7smsNot
8ucpSubmit
 .1.3.6.1.4.1.9.9.1300.1.8.1.2
cdsmrRuleCdrServiceQueue
Protocol used to examine message.
'none' : CDR Service queue not specified.
'available' : Matches when CDR service queue is available.
'congested' : Matches when CDR service queue is congested.
'unavailable': Ma…
Enumerationr/w
Enumerated Values:
0none
1available
2congested
3unavailable
 .1.3.6.1.4.1.9.9.1300.1.8.1.3
cdsmrRuleInputParameters
Many of the parameter used in the processing of rules
have default values. These values are determined
by a combination of variant and operation type. This
object will be provide information which parameter has
been sp…
Bitsr/w
Enumerated Values:
0cdrService
1destPort
2destSmeGta
3destSmeExact
4destSmeNai
5destSmeNp
6destSmeImsi
7destSmeMin
8destSmeMinDigits
9destSmeMaxDigits
10destSmeTable
11destSmeTableLoc
12destSmeTableImsi
13destSmeTableMin
14destSmeTableNai
15destSmeTableNp
16destSmscGta
17destSmscExact
18destSmscNai
19destSmscNp
20destSmscMinDigits
21destSmscMaxDigits
22origImsiGta
23origImsiExact
24origImsiUnknown
25origImsiNai
26origImsiNp
27origImsiMinDigits
28origImsiMaxDigits
29origImsiTable
30origImsiTableLoc
31origSmeGta
32origSmeExact
33origSmeNai
34origSmeNp
35origSmeMinDigits
36origSmeMaxDigits
37origSmeTable
38origSmeTableLoc
39origSmeTableNai
40origSmeTableNp
41origSmscGta
42origSmscExact
43origSmscNai
44origSmscNp
45origSmscMinDigits
46origSmscMaxDigits
47origSmscTable
48origSmscTableLoc
49origSmscTableNai
50origSmscTableNp
51pid
52tid
53default
 .1.3.6.1.4.1.9.9.1300.1.8.1.4
cdsmrRuleDestPort
A destination application port number. The value of the
port number maps to the values specified in the User
Data Header (UDH) of the SMS message.

This object only applies when the 'destPort' bit is
s…
Unsigned32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.9.1300.1.8.1.5
cdsmrRuleDestSmeGta
The destination short message entity global title address.

When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA clause of rule.
…
CISCO-ITP-TC-MIBCItpTcGtaLongDisplayr/w
Type Constraints:
range: 0..64
 .1.3.6.1.4.1.9.9.1300.1.8.1.6
cdsmrRuleDestSmeNai
The nature of specified address for the destination short
message entity global title address specified within the
message signal unit.

This object only applies when the 'destSmeNai' bit…
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.7
cdsmrRuleDestSmeNp
The numbering plan for the destination short message
entity global title address specified within the message
signal unit.

This object only applies when the 'destSmeNp' bit is
set in the …
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.8
cdsmrRuleDestSmeMinDigits
Specifies the minimum number of digits that the global
title address specified by the cdsmrRuleDestSmeGta object
can contain for rule to match.

This object only applies when the 'destSmeMinDigits' bit is…
CdsmrMinimumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.9
cdsmrRuleDestSmeMaxDigits
Specifies the maximum number of digits that the global
title address specified by the cdsmrRuleDestSmeGta object
can contain for rule to match.

This object only applies when the 'destSmeMaxDigits' bit is…
CdsmrMaximumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.10
cdsmrRuleDestSmeTable
The name of the entry in the cdsmrAddressTable that will be
searched for matches. The table will be search for the
following types of addresses based on values set in the
cdsmrRuleInputParameters object.
…
CISCO-ITP-MLR-MIBCmlrNamer/w
Type Constraints:
range: 0..20
Description:
The configured name used to identify various
tables used by MLR.

An octet string specified by an administrator that
must be in human-readable form. The names must
conform to the allowed characters that can b…
 .1.3.6.1.4.1.9.9.1300.1.8.1.11
cdsmrRuleDestSmeTableNai
The nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the 'destSmeTableNai' bit is
set in the cdsmrRuleInputParameters object.
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.12
cdsmrRuleDestSmeTableNp
The numbering plan for the destination short message
service center global title address specified within the
message signal unit.

This object only applies when the 'destSmeTableNp' bit…
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.13
cdsmrRuleDestSmscGta
The destination short message service center global title
address.

When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA c…
CISCO-ITP-TC-MIBCItpTcGtaLongDisplayr/w
Type Constraints:
range: 0..64
 .1.3.6.1.4.1.9.9.1300.1.8.1.14
cdsmrRuleDestSmscNai
The nature of specified address for the destination short
message service center global title address specified
within the message signal unit.

This object only applies when the 'destSm…
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.15
cdsmrRuleDestSmscNp
The numbering plan for the destination short message
service center global title address specified within the
message signal unit.

This object only applies when the 'destSmscNp' bit is…
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.16
cdsmrRuleDestSmscMinDigits
Specifies the minimum number of digits that the global
title address specified by the cdsmrRuleDestSmscGta object
can contain for rule to match.

This object only applies when the 'destSmscMinDigits' bit …
CdsmrMinimumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.17
cdsmrRuleDestSmscMaxDigits
Specifies the maximum number of digits that the global
title address specified by the cdsmrRuleDestSmscGta object
can contain for rule to match.

This object only applies when the 'destSmscMaxDigits' bit …
CdsmrMaximumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.18
cdsmrRuleOrigImsiGta
The origination short message entity global title address.

When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA clause of rule.
…
CISCO-ITP-TC-MIBCItpTcGtaLongDisplayr/w
Type Constraints:
range: 0..64
 .1.3.6.1.4.1.9.9.1300.1.8.1.19
cdsmrRuleOrigImsiNai
The nature of specified address for the origination short
message entity global title address specified within the
message signal unit.

This object only applies when the 'origImsiNai' bi…
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.20
cdsmrRuleOrigImsiNp
The numbering plan for the origination short message
entity global title address specified within the message
signal unit.

This object only applies when the 'origImsiNp' bit is
set in the…
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.21
cdsmrRuleOrigImsiMinDigits
Specifies the minimum number of digits that the global
title address specified by the cdsmrRuleOrigImsiGta object
can contain for rule to match.

This object only applies when the 'origImsiMinDigits' bit …
CdsmrMinimumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.22
cdsmrRuleOrigImsiMaxDigits
Specifies the maximum number of digits that the global
title address specified by the cdsmrRuleOrigImsiGta object
can contain for rule to match.

This object only applies when the 'origImsiMaxDigits' bit …
CdsmrMaximumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.23
cdsmrRuleOrigImsiTable
The name of the entry in the cdsmrAddressTable that will be
searched for matches. The table will be search for the
following types of addresses based on values set in the
cdsmrRuleInputParameters object.
…
CISCO-ITP-MLR-MIBCmlrNamer/w
Type Constraints:
range: 0..20
Description:
The configured name used to identify various
tables used by MLR.

An octet string specified by an administrator that
must be in human-readable form. The names must
conform to the allowed characters that can b…
 .1.3.6.1.4.1.9.9.1300.1.8.1.24
cdsmrRuleOrigSmeGta
The origination short message entity global title address.

When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA clause of rule.
…
CISCO-ITP-TC-MIBCItpTcGtaLongDisplayr/w
Type Constraints:
range: 0..64
 .1.3.6.1.4.1.9.9.1300.1.8.1.25
cdsmrRuleOrigSmeNai
The nature of specified address for the origination short
message entity global title address specified within the
message signal unit.

This object only applies when the 'origSmeNai' bit…
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.26
cdsmrRuleOrigSmeNp
The numbering plan for the origination short message
entity global title address specified within the message
signal unit.

This object only applies when the 'origSmeNp' bit is
set in the …
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.27
cdsmrRuleOrigSmeMinDigits
Specifies the minimum number of digits that the global
title address specified by the cdsmrRuleOrigSmeGta object
can contain for rule to match.

This object only applies when the 'origSmeMinDigits' bit is…
CdsmrMinimumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.28
cdsmrRuleOrigSmeMaxDigits
Specifies the maximum number of digits that the global
title address specified by the cdsmrRuleOrigSmeGta can
contain for rule to match.

This object only applies when the 'origSmeMaxDigits' bit is
set in…
CdsmrMaximumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.29
cdsmrRuleOrigSmeTable
The name of the entry in the cdsmrAddressTable that will be
searched for matches. The table will be search for the
following types of addresses based on values set in the
cdsmrRuleInputParameters object.
…
CISCO-ITP-MLR-MIBCmlrNamer/w
Type Constraints:
range: 0..20
Description:
The configured name used to identify various
tables used by MLR.

An octet string specified by an administrator that
must be in human-readable form. The names must
conform to the allowed characters that can b…
 .1.3.6.1.4.1.9.9.1300.1.8.1.30
cdsmrRuleOrigSmeTableNai
The nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the 'origSmeTableNai' bit is
set in the cdsmrRuleInputParameters object.
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.31
cdsmrRuleOrigSmeTableNp
The numbering plan for the destination short message
service center global title address specified within the
message signal unit.

This object only applies when the 'origSmeTableNp' bit…
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.32
cdsmrRuleOrigSmscGta
The origination short message service center global title
address.

When the length of the global title address is zero it
specified a wildcard match and all global title will
match GTA c…
CISCO-ITP-TC-MIBCItpTcGtaLongDisplayr/w
Type Constraints:
range: 0..64
 .1.3.6.1.4.1.9.9.1300.1.8.1.33
cdsmrRuleOrigSmscNai
The nature of specified address for the origination short
message service center global title address specified
within the message signal unit.

This object only applies when the 'origSm…
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.34
cdsmrRuleOrigSmscNp
The numbering plan for the origination short message
service center global title address specified within the
message signal unit.

This object only applies when the 'origSmscNp' bit is…
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.35
cdsmrRuleOrigSmscMinDigits
Specifies the minimum number of digits that the global
title address specified by the cdsmrRuleOrigSmscGta
object can contain for rule to match.

This object only applies when the 'origSmscMinDigits'
bi…
CdsmrMinimumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.36
cdsmrRuleOrigSmscMaxDigits
Specifies the maximum number of digits that the global
title address specified by the cdsmrRuleOrigSmscGta object
can contain for rule to match.

This object only applies when the 'origSmscMaxDigits' bit …
CdsmrMaximumDigitsr/w
Type Constraints:
range: 0..20
 .1.3.6.1.4.1.9.9.1300.1.8.1.37
cdsmrRuleOrigSmscTable
The name of the entry in the cdsmrAddressTable that will be
searched for matches. The table will be search for the
following types of addresses based on values set in the
cdsmrRuleInputParameters object.
…
CISCO-ITP-MLR-MIBCmlrNamer/w
Type Constraints:
range: 0..20
Description:
The configured name used to identify various
tables used by MLR.

An octet string specified by an administrator that
must be in human-readable form. The names must
conform to the allowed characters that can b…
 .1.3.6.1.4.1.9.9.1300.1.8.1.38
cdsmrRuleOrigSmscTableNai
The nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the 'origSmscTableNai' bit is
set in the cdsmrRuleInputParameters object.
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.39
cdsmrRuleOrigSmscTableNp
The numbering plan for the destination short message
service center global title address specified within the
message signal unit.

This object only applies when the 'origSmscTableNp' bi…
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.40
cdsmrRuleProtocolId
The protocol identifier value used for the 'smsMo and
'smsMt' operations specified by the
cdsmrRuleParmsOperationType object.

The value of the cdsmrRuleParmsMatchPid object maps to the
values specifie…
Unsigned32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.9.9.1300.1.8.1.41
cdsmrRuleTeleserviceId
The Teleservice identifier value for the following types
of operations specified by the cdsmrRuleParmsOperationType
object.
'smdPp'
'smsMo'
'smsMt'
'smsNotify'
The value of the cdsmrRuleParmsMatchTi…
Unsigned32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.9.9.1300.1.8.1.42
cdsmrRuleResultParameters
Many of the parameter used in the processing of rules
have default values. These values are determined
by a combination of variant and operation type. This
object will be provide information on which parameter
have be…
CdsmrResultParametersr/w
Type Values:
0network
1octet
2tranType
3gti
4np
5nai
6pc
7ssn
8ruleNumber
 .1.3.6.1.4.1.9.9.1300.1.8.1.43
cdsmrRuleResultNetwork
The network name is used to indicate the network in which
the result operation will be performed.
CISCO-ITP-TC-MIBCItpTcNetworkNamer/w
Type Constraints:
range: 0..19
 .1.3.6.1.4.1.9.9.1300.1.8.1.44
cdsmrRuleResultType
Specified the type of information to be placed
into the message signal unit or how the it
will be processed.
CdsmrResultTyper/w
Type Values:
0none
1pc
2pcSsn
3gt
4group
5smpp
6ucp
7block
8ruleNext
9ruleNumber
10deliverMt
11origImsi
12origImsiNext
 .1.3.6.1.4.1.9.9.1300.1.8.1.45
cdsmrRuleResultOctet
Information to be placed in the message signal
unit based on the value specified by the
cdsmrRuleSetResultType object. When the
cdsmrRuleSetResultType object is set to 'pc'
or 'none' this object will not be used in t…
CdsmrResultOctetr/w
Type Constraints:
range: 0..64
 .1.3.6.1.4.1.9.9.1300.1.8.1.46
cdsmrRuleResultTransType
The translation type specified within the address in the
message signal unit. This object only applies when the
cdsmrRuleSetResultType is set to 'gt' value.
CISCO-ITP-GSCCP-MIBCgsccpGttTransTyper/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.47
cdsmrRuleResultGti
The global title indicator value for the global tile address
specified within the message signal unit. This object only
applies when the cdsmrRuleSetResultType is set to
'gt' value.
CISCO-ITP-GSCCP-MIBCgsccpGttGlobalTitleIndr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.48
cdsmrRuleResultNp
The numbering plan for the global tile address specified
within the message signal unit. This object only applies
when the cdsmrRuleSetResultType is set to 'gt' value.
CISCO-ITP-TC-MIBCItpTcNumberingPlanr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.49
cdsmrRuleResultNai
The nature of specified address for the global tile
address specified within the message signal unit. This
object only applies when the cdsmrRuleSetResultType is
set to 'gt' value.
CISCO-ITP-TC-MIBCItpTcNAIr/w
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.50
cdsmrRuleResultPc
The point-code to be place in the message signal unit. This
object only applies when the cdsmrRuleResultType is set
to 'pc' value.
CISCO-ITP-TC-MIBCItpTcPointCoder/w
Type Constraints:
range: 0..16777216
 .1.3.6.1.4.1.9.9.1300.1.8.1.51
cdsmrRuleResultSsn
The subsystem number to be place in the message signal unit.
This object only applies when the cdsmrRuleResultType is set
to 'ssn' value.
CISCO-ITP-TC-MIBCItpTcSubSystemNumberr/w
Type Constraints:
range: 0
range: 2..255
 .1.3.6.1.4.1.9.9.1300.1.8.1.52
cdsmrRuleResultRuleNumber
This object specifies the next rule to execute when
rule matches. The specified rule number must be greater
than current rule.
CISCO-ITP-MLR-MIBCmlrIdr/w
Type Constraints:
range: 0..65535
Description:
A numeric identifier used to specify an entry in a list.
Zero is a special value used to indicate no entry.
 .1.3.6.1.4.1.9.9.1300.1.8.1.53
cdsmrRuleResultRowStatus
The object is used by a management station to
create or delete the row entry in cdsmrRuleTable
following the RowStatus textual convention.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.9.9.1300.1.8.1.54

cdsmrRuleStatsTable

table
.1.3.6.1.4.1.9.9.1300.1.9 · 1 row entry · 3 columns
Open in standard view
Uses the cisco variant from /opt/observium/mibs/cisco.
Command help
Walk cdsmrRuleStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ITP-DSMR-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ITP-DSMR-MIB::cdsmrRuleStatsTable' 
A table that is used to specify attributes of an
application-layer message to be matched and the resulting
behavior for handling the message.
cdsmrRuleStatsTableEntry row .1.3.6.1.4.1.9.9.1300.1.9.1
Entries in this table provide measurements for entries in
cdsmrRuleTable.
Indexes
Column Syntax OID
cdsmrRuleStatsCheckedCounts
Count of the number of times this rule was checked.
checksSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.9.1.1
cdsmrRuleStatsMatchCounts
Count of the number of times this rule was matched.
matchesSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.9.1.2
cdsmrRuleStatsRoutedCounts
Count of the number of times this rule was matched
and packet was routed using mechanism specified by
result.
successesSNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.9.1300.1.9.1.3