CISCO-ICSUDSU-MIB Table View

The CSU/DSU Static Configuration Table.  Contains items
that are statically configured and can not be changed by end
user without physically changing the CSU/DSU.

ciscoICsuDsuStaticConfigEntry row .1.3.6.1.4.1.9.9.44.1.1.1.1

An entry in the static configuration table for each
integrated CSU/DSU.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
ciscoICsuDsuType Specifies the type of line interface or CSU/DSU.	Enumeration Enumerated Values: 1 fractionalT1 2 twoWireSwitched56k 3 fourWireSwitched56k 4 unknown	.1.3.6.1.4.1.9.9.44.1.1.1.1.1
ciscoICsuDsuHwRevision The CSU/DSU hardware revision.	OctetString Constraints: range: 1-16	.1.3.6.1.4.1.9.9.44.1.1.1.1.2
ciscoICsuDsuSwRevision The CSU/DSU software revision.	OctetString Constraints: range: 1-16	.1.3.6.1.4.1.9.9.44.1.1.1.1.3
ciscoICsuDsuProtocolRevision The Protocol Revision of the CSU/DSU.	OctetString Constraints: range: 1-16	.1.3.6.1.4.1.9.9.44.1.1.1.1.4

The CSU/DSU test report Table.  Contains the results of user
initiated tests, including selftest, reset, and loopback.

ciscoICsuDsuTestReportEntry row .1.3.6.1.4.1.9.9.44.1.1.2.1

An entry in the test report table for each integrated
CSU/DSU.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
ciscoICsuDsuLastSelfTestResult The result of the last self test. Represented as a sum of a bit map. The variable bit positions are: 1 - Flash Checksum bad. Catastrophic error. 2 - EPROM Checksum bad. Catastrophic error. 4 - RAM Tests failed. Ca…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.9.44.1.1.2.1.1
ciscoICsuDsuTimeOfLastSelfTest SysUpTime of LastSelfTest execution.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.44.1.1.2.1.2
ciscoICsuDsuNumResets Number of times CSU/DSU has been reset.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.1.2.1.3
ciscoICsuDsuTimeOfLastReset SysUpTime of last CSU/DSU reset.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.44.1.1.2.1.4
ciscoICsuDsuLoopbackStatus Current Status of Loopback. Remaining Loopback results are valid only if status is 'completed' or 'failed' or 'noSyncWithTestPattern'.	Enumeration Enumerated Values: 1 completed 2 inProgress 3 neverPerformed 4 failed 5 noSyncWithTestPattern	.1.3.6.1.4.1.9.9.44.1.1.2.1.5
ciscoICsuDsuLoopbackNumErrors Number of Bit errors that occurred in last successful loopback test. Valid only if remote loopback with pattern was performed and a sync was achieved on the test pattern.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.9.44.1.1.2.1.6
ciscoICsuDsuLoopbackDuration Duration of last successful loopback test in hundredths of seconds. Note that it is possible for the CSU/DSU to lose framing during the test. If so, the duration represents the time between reframing and end of tes…	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.1.2.1.7
ciscoICsuDsuLoopbackPoint Point in network where last loopback was performed. Meaning for t1 CSU/DSU: dtePayload - local DSU loopback. The configured 'fractions' of the DS1 signal is looped back as the receive signal. …	Enumeration Enumerated Values: 1 dtePayload 2 dteFull 3 lineFull 4 linePayload 5 remoteSmartJack 6 remoteFull 7 remotePayload	.1.3.6.1.4.1.9.9.44.1.1.2.1.8
ciscoICsuDsuLoopbackPattern Test pattern used for locally initiated remote loopback. Valid only if a remote loopback was last performed. Following patterns valid for T1 or Switched 56k CSU/DSU: noPattern - no specific pattern is use…	Enumeration Enumerated Values: 1 noPattern 2 patternQRW 3 pattern0In1 4 pattern1In1 5 pattern1In2 6 pattern1In3 7 pattern1In5 8 pattern1In8 9 pattern3In24 10 patternUser 11 pattern2047 12 pattern511 13 patternStressDDS1 14 patternStressDDS2 15 patternStressDDS3 16 patternStressDDS4	.1.3.6.1.4.1.9.9.44.1.1.2.1.9
ciscoICsuDsuUserDefinedPattern User Defined Loopback Pattern. Valid only if ciscoICsuDsuLoopbackPattern is patternUser.	OctetString Constraints: range: 1-24	.1.3.6.1.4.1.9.9.44.1.1.2.1.10
ciscoICsuDsuLoopbackCode LoopCode used to initiate last remote loopback. Valid only if a only if a remote loopback was last performed. standard - standard loopback code. Usually consists of the repeated binary pattern of '00001' alte…	Enumeration Enumerated Values: 1 standard 2 alternate 3 v54	.1.3.6.1.4.1.9.9.44.1.1.2.1.11
ciscoICsuDsuEndTimeOfLastLoopback SysUpTime of completion of last loopback test execution.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.44.1.1.2.1.12

The T1 CSU/DSU Unit Configuration Table.  Contains current
T1 CSU/DSU configuration parameters not covered by RFC1406.

ciscoICsuDsuT1ConfigEntry row .1.3.6.1.4.1.9.9.44.1.2.1.1

An entry in the configuration table for each integrated
T1 CSU/DSU.

Indexes

No indexes recorded

Column	Syntax	OID
ciscoICsuDsuT1LineBuildOut Line build out (LBO) is loss inserted by the CSU in order to meet the 15 to 22.5 dB loss requirement of the premises remote-end section. Selected so that (phone company loss) + (cable length loss) + (line build out) i…	Enumeration Enumerated Values: 1 buildOut0 2 buildOut7p5 3 buildOut15	.1.3.6.1.4.1.9.9.44.1.2.1.1.1
ciscoICsuDsuT1DteLineCode Indicates whether the DTE line code is inverted or not. When fractional timeslots are configured for 64kps and AMI linecode, a combination of inverting the DTE line code along with the proper line protocol (i.e. HDLC/…	Enumeration Enumerated Values: 1 normal 2 inverted	.1.3.6.1.4.1.9.9.44.1.2.1.1.2
ciscoICsuDsuT1SupportRemoteAlarmIndication Determines if unit will generate or detect a remote alarm indication (RAI) signal which is also known as a yellow alarm. In D4 framing format, DTE equipment (including Frame Relay equipment) that is using the HDLC or S…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.44.1.2.1.1.3
ciscoICsuDsuT1FullBandwidthRemoteLoopcode LoopCode to be accepted from remote end to place unit in and out of full bandwidth loopback. standard - standard loopback code. Usually consists of the repeated binary pattern of '00001' alternate - alternate…	Enumeration Enumerated Values: 1 standard 2 alternate 3 disabled	.1.3.6.1.4.1.9.9.44.1.2.1.1.4
ciscoICsuDsuT1PayloadRemoteLoopcode LoopCode to be accepted from remote end to place unit in and out of payload or fractional loopback. standard - standard loopback code. Usually consists of the repeated binary pattern of '00001' alternate - al…	Enumeration Enumerated Values: 1 standard 2 alternate 3 disabled 4 v54	.1.3.6.1.4.1.9.9.44.1.2.1.1.5

The T1 CSU/DSU Unit Status Table.  Contains information about
the status of the CSU/DSU, including externally generated
alarm conditions.

ciscoICsuDsuT1StatusEntry row .1.3.6.1.4.1.9.9.44.1.2.2.1

An entry in the status table for each integrated T1 CSU/DSU.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
ciscoICsuDsuT1LoopStatus Current Loop status of T1 CSU/DSU. Represented as a sum of a bit map. The variable bit positions are: 1 - lossofSignal (LOS); unable to detect the DS1 signal. 2 - lossofFrame (LOF); unable to synchronize on the DS1 …	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.9.44.1.2.2.1.1
ciscoICsuDsuT1LossOfSignals Number of times lossofSignal event detected.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.2.2.1.2
ciscoICsuDsuT1LossOfFrames Number of times lossofFrame event detected.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.2.2.1.3
ciscoICsuDsuT1RemoteAlarmIndications Number of times RemoteAlarmIndication signal or yellow alarm received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.2.2.1.4
ciscoICsuDsuT1AlarmIndicationSignals Number of times Alarm Indication Signal or blue alarm received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.2.2.1.5

The Switched 56k CSU/DSU Configuration Table.  Contains
current Sw56k CSU/DSU configuration parameters.

ciscoICsuDsuSw56kConfigEntry row .1.3.6.1.4.1.9.9.44.1.3.1.1

An entry in the sw56k configuration table for each integrated
switched 56 kbps CSU/DSU.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
ciscoICsuDsuSw56kNetworkType Configures the DSU Module for the specific type of network being used. dds - AT&T's Dataphone Digital Service, generically known as Digital Data System. Requires 4-Wire interface. att - AT&T's Switched 56 Netwo…	Enumeration Enumerated Values: 1 dds 2 att 3 sprint 4 otherCarrier	.1.3.6.1.4.1.9.9.44.1.3.1.1.1
ciscoICsuDsuSw56kClockSource Specifies the timing source for the DSU. 'internal' indicates timing provided by DSU. 'line' indicates timing provided by network receive signal.	Enumeration Enumerated Values: 1 internal 2 line	.1.3.6.1.4.1.9.9.44.1.3.1.1.2
ciscoICsuDsuSw56kLoopRate The Loop Rate option selects the network loop operating speed. Only 'ciscoICsuDsuSw56kNetworkType' of 'dds' supports all listed loop rates. 'att' and 'sprint' network types only support 'bps56k' or 56 kilobits per se…	Enumeration Enumerated Values: 1 bps2400 2 bps4800 3 bps9600 4 bps19k 5 bps38k 6 bps56k 7 bps64k	.1.3.6.1.4.1.9.9.44.1.3.1.1.3
ciscoICsuDsuSw56kScramblerEnabled Indicates if line code scrambling is enabled. Scrambling is used to prevent DTE data sequences that minic network loop maintenance functions from activating loopback. Only supported when operating in DDS mode at 64kbps…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.44.1.3.1.1.4
ciscoICsuDsuSw56kRemoteLoopbackEnabled Indicates if a request for Remote Digital Loopback is will be accepted.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.44.1.3.1.1.5

The Sw56k CSU/DSU Status Table.  Contains information about
the status of the CSU/DSU, including externally generated
alarm conditions.

ciscoICsuDsuSw56kLineStatusEntry row .1.3.6.1.4.1.9.9.44.1.3.2.1

An entry in the sw56k status table for each integrated
switched 56 kbps CSU/DSU.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
ciscoICsuDsuSw56kDialingStatus This variable indicates the dialing status of units using switched connections. idle - on-hook and no call in progress. dialing - dialing a number. onLine - Online passing data. noWinkFromSwitch - No wink from switch (…	Enumeration Enumerated Values: 1 idle 2 dialing 3 online 4 noWinkFromSwitch 5 numberBusy 6 noAnswer	.1.3.6.1.4.1.9.9.44.1.3.2.1.1
ciscoICsuDsuSw56kLoopStatus Current loop status or alarm condition. Represented as a sum of a bit map. The variable bit positions are: 1 oosOofFromNetwork - The DSU is receiving Out of Service/ Out of Frame code from ne…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.9.9.44.1.3.2.1.2
ciscoICsuDsuSw56kReceivedOosOofs Number of times OOS/OOF (Out Of Sync / Out Of Frame) code received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.3.2.1.3
ciscoICsuDsuSw56kLostSealingCurrents Number of times Lost Sealing Current.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.3.2.1.4
ciscoICsuDsuSw56kLostReceiveSignals Number of times lost receive signal.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.3.2.1.5
ciscoICsuDsuSw56kLostFrameSyncs Number of times lost frame synchronization.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.3.2.1.6
ciscoICsuDsuSw56kLoopRateSearches Number of times attempted Loop Rate Search.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.44.1.3.2.1.7