CISCO-CEF-MIB Table View

This table contains the summary information
for the cefPrefixTable.

cefFIBSummaryEntry row .1.3.6.1.4.1.9.9.492.1.1.1.1.1

If CEF is enabled on the Managed device,
each entry contains the FIB summary related
attributes for the managed entity.

A row may exist for each IP version type
(v4 and v6) depending upon the IP version
sup…

Indexes

ENTITY-MIBentPhysicalIndex cefFIBIpVersion

Column	Syntax	OID
cefFIBIpVersion The version of IP forwarding.	CISCO-CEF-TCCefIpVersion Type Values: 1 ipv4 2 ipv6	.1.3.6.1.4.1.9.9.492.1.1.1.1.1.1
cefFIBSummaryFwdPrefixes Total number of forwarding Prefixes in FIB for the IP version specified by cefFIBIpVersion object.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.1.1.1.1.2

A list of CEF forwarding prefixes.

cefPrefixEntry row .1.3.6.1.4.1.9.9.492.1.1.2.1

If CEF is enabled on the Managed device,
each entry contains the forwarding
prefix attributes.

CEF prefix based non-recursive stats are maintained
in internal and external buckets (depending upon the
val…

Indexes

ENTITY-MIBentPhysicalIndex cefPrefixType cefPrefixAddr cefPrefixLen

Column	Syntax	OID
cefPrefixType The Network Prefix Type. This object specifies the address type used for cefPrefixAddr. Prefix entries are only valid for the address type of ipv4(1) and ipv6(2).	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.492.1.1.2.1.1
cefPrefixAddr The Network Prefix Address. The type of this address is determined by the value of the cefPrefixType object. This object is a Prefix Address containing the prefix with length specified by cefPrefixLen. Any bits beyond…	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.1.2.1.2
cefPrefixLen Length in bits of the FIB Address prefix.	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.9.9.492.1.1.2.1.3
cefPrefixForwardingInfo This object indicates the associated forwarding element selection entries in cefFESelectionTable. The value of this object is index value (cefFESelectionName) of cefFESelectionTable.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.1.2.1.4
cefPrefixPkts If CEF accounting is set to enable per prefix accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'perPrefix' accounting), then this object represents the number of packets switched to…	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.1.2.1.5
cefPrefixHCPkts If CEF accounting is set to enable per prefix accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'perPrefix' accounting), then this object represents the number of packets switched to…	packetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.1.2.1.6
cefPrefixBytes If CEF accounting is set to enable per prefix accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'perPrefix' accounting), then this object represents the number of bytes switched to t…	bytesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.1.2.1.7
cefPrefixHCBytes If CEF accounting is set to enable per prefix accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'perPrefix' accounting), then this object represents the number of bytes switched to t…	bytesSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.1.2.1.8
cefPrefixInternalNRPkts If CEF accounting is set to enable non-recursive accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'nonRecursive' accounting), then this object represents the number of non-recursive …	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.1.2.1.9
cefPrefixInternalNRHCPkts If CEF accounting is set to enable non-recursive accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'nonRecursive' accounting), then this object represents the number of non-recursive …	packetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.1.2.1.10
cefPrefixInternalNRBytes If CEF accounting is set to enable nonRecursive accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'nonRecursive' accounting), then this object represents the number of non-recursive …	bytesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.1.2.1.11
cefPrefixInternalNRHCBytes If CEF accounting is set to enable nonRecursive accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'nonRecursive' accounting), then this object represents the number of non-recursive …	bytesSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.1.2.1.12
cefPrefixExternalNRPkts If CEF accounting is set to enable non-recursive accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'nonRecursive' accounting), then this object represents the number of non-recursive …	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.1.2.1.13
cefPrefixExternalNRHCPkts If CEF accounting is set to enable non-recursive accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'nonRecursive' accounting), then this object represents the number of non-recursive …	packetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.1.2.1.14
cefPrefixExternalNRBytes If CEF accounting is set to enable nonRecursive accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'nonRecursive' accounting), then this object represents the number of non-recursive …	bytesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.1.2.1.15
cefPrefixExternalNRHCBytes If CEF accounting is set to enable nonRecursive accounting (value of cefCfgAccountingMap object in the cefCfgEntry is set to enable 'nonRecursive' accounting), then this object represents the number of non-recursive …	bytesSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.1.2.1.16

A table of Longest Match Prefix Query requests.
          
Generator application should utilize the
cefLMPrefixSpinLock to try to avoid collisions.
See DESCRIPTION clause of cefLMPrefixSpinLock.

cefLMPrefixEntry row .1.3.6.1.4.1.9.9.492.1.1.4.1

If CEF is enabled on the managed device, then each
entry represents a longest Match Prefix request.

A management station wishing to get the longest
Match prefix for a given destination address
should create…

Indexes

ENTITY-MIBentPhysicalIndex cefLMPrefixDestAddrType cefLMPrefixDestAddr

Column	Syntax	OID
cefLMPrefixDestAddrType The Destination Address Type. This object specifies the address type used for cefLMPrefixDestAddr. Longest Match Prefix entries are only valid for the address type of ipv4(1) and ipv6(2).	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.492.1.1.4.1.1
cefLMPrefixDestAddr The Destination Address. The type of this address is determined by the value of the cefLMPrefixDestAddrType object.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.1.4.1.2
cefLMPrefixState Indicates the state of this prefix search request.	CISCO-CEF-TCCefPrefixSearchState Type Values: 1 running 2 matchFound 3 noMatchFound	.1.3.6.1.4.1.9.9.492.1.1.4.1.3
cefLMPrefixAddr The Network Prefix Address. Index to the cefPrefixTable. The type of this address is determined by the value of the cefLMPrefixDestAddrType object.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.1.4.1.4
cefLMPrefixLen The Network Prefix Length. Index to the cefPrefixTable.	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.9.9.492.1.1.4.1.5
cefLMPrefixRowStatus The status of this table entry. Once the entry status is set to active(1), the associated entry cannot be modified until the request completes (cefLMPrefixState transitions to matchFound(2) or noMatchFound(3)). …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.492.1.1.4.1.6

CEF prefix path is a valid route to reach to a 
destination IP prefix. Multiple paths may exist 
out of a router to the same destination prefix. 
This table specify lists of CEF paths.

cefPathEntry row .1.3.6.1.4.1.9.9.492.1.1.5.1

If CEF is enabled on the Managed device,
each entry contain a CEF prefix path.

entPhysicalIndex is also an index for this
table which represents entities of
'module' entPhysicalClass which are capable
of ru…

Indexes

ENTITY-MIBentPhysicalIndex cefPrefixType cefPrefixAddr cefPrefixLen cefPathId

Column	Syntax	OID
cefPathId The locally arbitrary, but unique identifier associated with this prefix path entry.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.492.1.1.5.1.1
cefPathType Type for this CEF Path.	CISCO-CEF-TCCefPathType Type Values: 1 receive 2 connectedPrefix 3 attachedPrefix 4 attachedHost 5 attachedNexthop 6 recursiveNexthop 7 adjacencyPrefix 8 specialPrefix 9 unknown	.1.3.6.1.4.1.9.9.492.1.1.5.1.2
cefPathInterface Interface associated with this CEF path. A value of zero for this object will indicate that no interface is associated with this path entry.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.9.9.492.1.1.5.1.3
cefPathNextHopAddr Next hop address associated with this CEF path. The value of this object is only relevant for attached next hop and recursive next hop path types (when the object cefPathType is set to attachedNexthop(4…	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.1.5.1.4
cefPathRecurseVrfName The recursive vrf name associated with this path. The value of this object is only relevant for recursive next hop path types (when the object cefPathType is set to recursiveNexthop(5)), and '0x00' will …	MPLS-VPN-MIBMplsVpnId Type Constraints: range: 0..31	.1.3.6.1.4.1.9.9.492.1.1.5.1.5

This table contains the summary information
for the cefAdjTable.

cefAdjSummaryEntry row .1.3.6.1.4.1.9.9.492.1.2.1.1.1

If CEF is enabled on the Managed device,
each entry contains the CEF Adjacency
summary related attributes for the
Managed entity. A row exists for
each adjacency link type.

entPhysicalIndex is also an ind…

Indexes

ENTITY-MIBentPhysicalIndex cefAdjSummaryLinkType

Column	Syntax	OID
cefAdjSummaryLinkType The link type of the adjacency.	CISCO-CEF-TCCefAdjLinkType Type Values: 1 ipv4 2 ipv6 3 mpls 4 raw 5 unknown	.1.3.6.1.4.1.9.9.492.1.2.1.1.1.1
cefAdjSummaryComplete The total number of complete adjacencies. The total number of adjacencies which can be used to switch traffic to a neighbour.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.2.1.1.1.2
cefAdjSummaryIncomplete The total number of incomplete adjacencies. The total number of adjacencies which cannot be used to switch traffic in their current state.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.2.1.1.1.3
cefAdjSummaryFixup The total number of adjacencies for which the Layer 2 encapsulation string (header) may be updated (fixed up) at packet switch time.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.2.1.1.1.4
cefAdjSummaryRedirect The total number of adjacencies for which ip redirect (or icmp redirection) is enabled. The value of this object is only relevant for ipv4 and ipv6 link type (when the index object cefAdjSummaryLinkType value is ipv4(…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.2.1.1.1.5

A list of CEF adjacencies.

cefAdjEntry row .1.3.6.1.4.1.9.9.492.1.2.2.1

If CEF is enabled on the Managed device,
each entry contains the adjacency
attributes. Adjacency entries may exist
for all the interfaces on which packets
can be switched out of the device.
The interface is instantiate…

Indexes

ENTITY-MIBentPhysicalIndex IF-MIBifIndex cefAdjNextHopAddrType cefAdjNextHopAddr cefAdjConnId cefAdjSummaryLinkType

Column	Syntax	OID
cefAdjNextHopAddrType Address type for the cefAdjNextHopAddr. This object specifies the address type used for cefAdjNextHopAddr. Adjacency entries are only valid for the address type of ipv4(1) and ipv6(2).	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.492.1.2.2.1.1
cefAdjNextHopAddr The next Hop address for this adjacency. The type of this address is determined by the value of the cefAdjNextHopAddrType object.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.2.2.1.2
cefAdjConnId In cases where cefLinkType, interface and the next hop address are not able to uniquely define an adjacency entry (e.g. ATM and Frame Relay Bundles), this object is a unique identifier to differentiate between these adj…	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.9.9.492.1.2.2.1.3
cefAdjSource If the adjacency is created because some neighbour discovery mechanism has discovered a neighbour and all the information required to build a frame header to encapsulate traffic to the neighbour is available then the so…	CISCO-CEF-TCCefAdjacencySource Type Values: 0 atom 1 linkRawAdj 2 ipPseudowireAdj 3 arp 4 p2pAdj 5 frMap 6 atmPVC 7 atmSVC 8 atmTVC 9 nbma 10 mpoa 11 atmBundle 12 lec 13 nhrp 14 ipv6ND 15 cmcc 16 ipv6SixtoFourTunnel 17 ipv6IsaTapTunnel 18 ipv6AutoTunnel 19 fibLc 20 virtual 21 multicast 22 unknown	.1.3.6.1.4.1.9.9.492.1.2.2.1.4
cefAdjEncap The layer 2 encapsulation string to be used for sending the packet out using this adjacency.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.2.2.1.5
cefAdjFixup For the cases, where the encapsulation string is decided at packet switch time, the adjacency encapsulation string specified by object cefAdjEncap require a fixup. I.e. for the adjacencies out of IP Tunnels, the stri…	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.2.2.1.6
cefAdjMTU The Layer 3 MTU which can be transmitted using this adjacency.	bytesUnsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.492.1.2.2.1.7
cefAdjForwardingInfo This object selects a forwarding info entry defined in the cefFESelectionTable. The selected target is defined by an entry in the cefFESelectionTable whose index value (cefFESelectionName) is equal to this object. …	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.2.2.1.8
cefAdjPkts Number of pkts transmitted using this adjacency.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.2.2.1.9
cefAdjHCPkts Number of pkts transmitted using this adjacency. This object is a 64-bit version of cefAdjPkts.	packetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.2.2.1.10
cefAdjBytes Number of bytes transmitted using this adjacency.	bytesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.2.2.1.11
cefAdjHCBytes Number of bytes transmitted using this adjacency. This object is a 64-bit version of cefAdjBytes.	bytesSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.2.2.1.12

A list of forwarding element selection entries.

cefFESelectionEntry row .1.3.6.1.4.1.9.9.492.1.3.1.1

If CEF is enabled on the Managed device,
each entry contain a CEF forwarding element
selection list.

entPhysicalIndex is also an index for this
table which represents entities of
'module' entPhysicalClass w…

Indexes

ENTITY-MIBentPhysicalIndex cefFESelectionName cefFESelectionId

Column	Syntax	OID
cefFESelectionName The locally arbitrary, but unique identifier used to select a set of forwarding element lists.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.9.492.1.3.1.1.1
cefFESelectionId Secondary index to identify a forwarding elements List in this Table.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.492.1.3.1.1.2
cefFESelectionSpecial Special processing for a destination is indicated through the use of special forwarding element. If the forwarding element list contains the special forwarding element, then this object represents the…	CISCO-CEF-TCCefForwardingElementSpecialType Type Values: 1 illegal 2 punt 3 drop 4 discard 5 null 6 glean 7 unresolved 8 noRoute 9 none	.1.3.6.1.4.1.9.9.492.1.3.1.1.3
cefFESelectionLabels This object represent the MPLS Labels associated with this forwarding Element List. The value of this object will be irrelevant and will be set to zero length if the forwarding element list doesn't cont…	CISCO-CEF-TCCefMplsLabelList Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.3.1.1.4
cefFESelectionAdjLinkType This object represent the link type for the adjacency associated with this forwarding Element List. The value of this object will be irrelevant and will be set to unknown(5) if the forwarding element lis…	CISCO-CEF-TCCefAdjLinkType Type Values: 1 ipv4 2 ipv6 3 mpls 4 raw 5 unknown	.1.3.6.1.4.1.9.9.492.1.3.1.1.5
cefFESelectionAdjInterface This object represent the interface for the adjacency associated with this forwarding Element List. The value of this object will be irrelevant and will be set to zero if the forwarding element list does…	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.9.9.492.1.3.1.1.6
cefFESelectionAdjNextHopAddrType This object represent the next hop address type for the adjacency associated with this forwarding Element List. The value of this object will be irrelevant and will be set to unknown(0) if the forwarding…	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.492.1.3.1.1.7
cefFESelectionAdjNextHopAddr This object represent the next hop address for the adjacency associated with this forwarding Element List. The value of this object will be irrelevant and will be set to zero if the forwarding element li…	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.3.1.1.8
cefFESelectionAdjConnId This object represent the connection id for the adjacency associated with this forwarding Element List. The value of this object will be irrelevant and will be set to zero if the forwarding element list …	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.9.9.492.1.3.1.1.9
cefFESelectionVrfName This object represent the Vrf name for the lookup associated with this forwarding Element List. The value of this object will be irrelevant and will be set to a string containing the single octet 0x00 if…	MPLS-VPN-MIBMplsVpnId Type Constraints: range: 0..31	.1.3.6.1.4.1.9.9.492.1.3.1.1.10
cefFESelectionWeight This object represent the weighting for load balancing between multiple Forwarding Element Lists. The value of this object will be zero if load balancing is associated with this selection entry.	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.9.9.492.1.3.1.1.11

This table contains global config parameter 
of CEF on the Managed device.

cefCfgEntry row .1.3.6.1.4.1.9.9.492.1.4.1.1

If the Managed device supports CEF,
each entry contains the CEF config
parameter for the managed entity.
A row may exist for each IP version type
(v4 and v6) depending upon the IP version
supported on the device.
…

Indexes

ENTITY-MIBentPhysicalIndex cefFIBIpVersion

Column	Syntax	OID
cefCfgAdminState The desired state of CEF.	CISCO-CEF-TCCefAdminStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.9.9.492.1.4.1.1.1
cefCfgOperState The current operational state of CEF. If the cefCfgAdminState is disabled(2), then cefOperState will eventually go to the down(2) state unless some error has occurred. If cefCfgAdminState …	CISCO-CEF-TCCefOperStatus Type Values: 1 up 2 down	.1.3.6.1.4.1.9.9.492.1.4.1.1.2
cefCfgDistributionAdminState The desired state of CEF distribution.	CISCO-CEF-TCCefAdminStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.9.9.492.1.4.1.1.3
cefCfgDistributionOperState The current operational state of CEF distribution. If the cefCfgDistributionAdminState is disabled(2), then cefDistributionOperState will eventually go to the down(2) state unless some error has occurred.…	CISCO-CEF-TCCefOperStatus Type Values: 1 up 2 down	.1.3.6.1.4.1.9.9.492.1.4.1.1.4
cefCfgAccountingMap This object represents a bitmap of network accounting options. CEF network accounting is disabled by default. CEF network accounting can be enabled by selecting one or more of the followin…	Bitsr/w Enumerated Values: 0 nonRecursive 1 perPrefix 2 prefixLength	.1.3.6.1.4.1.9.9.492.1.4.1.1.5
cefCfgLoadSharingAlgorithm Indicates the CEF Load balancing algorithm. Setting this object to none(1) will disable the Load sharing for the specified entry. CEF load balancing can be enabled by setting this object t…	Enumerationr/w Enumerated Values: 1 none 2 original 3 tunnel 4 universal	.1.3.6.1.4.1.9.9.492.1.4.1.1.6
cefCfgLoadSharingID The Fixed ID associated with the managed object cefCfgLoadSharingAlgorithm. The hash of this object value may be used by the Load Sharing Algorithm. The value of this object is not relevant and will be se…	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.9.9.492.1.4.1.1.7
cefCfgTrafficStatsLoadInterval The interval time over which the CEF traffic statistics are collected.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.4.1.1.8
cefCfgTrafficStatsUpdateRate The frequency with which the line card sends the traffic load statistics to the Router Processor. Setting the value of this object to 0 will disable the CEF traffic statistics collection.	secondsUnsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.492.1.4.1.1.9

This table contains global resource 
information of CEF on the Managed device.

cefResourceEntry row .1.3.6.1.4.1.9.9.492.1.4.2.1

If the Managed device supports CEF,
each entry contains the CEF Resource
parameters for the managed entity.

entPhysicalIndex is also an index for this
table which represents entities of
'module' entPhysica…

Indexes

ENTITY-MIBentPhysicalIndex

Column	Syntax	OID
cefResourceMemoryUsed Indicates the number of bytes from the Processor Memory Pool that are currently in use by CEF on the managed entity.	bytesSNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.4.2.1.1
cefResourceFailureReason The CEF resource failure reason which may lead to CEF being disabled on the managed entity.	CISCO-CEF-TCCefFailureReason Type Values: 1 none 2 mallocFailure 3 hwFailure 4 keepaliveFailure 5 noMsgBuffer 6 invalidMsgSize 7 internalError	.1.3.6.1.4.1.9.9.492.1.4.2.1.2

This Table contains interface specific
information of CEF on the Managed
device.

cefIntEntry row .1.3.6.1.4.1.9.9.492.1.5.1.1

If CEF is enabled on the Managed device,
each entry contains the CEF attributes
associated with an interface.
The interface is instantiated by ifIndex.
Therefore, the interface index must have been
assigned, accordi…

Indexes

ENTITY-MIBentPhysicalIndex cefFIBIpVersion IF-MIBifIndex

Column	Syntax	OID
cefIntSwitchingState The CEF switching State for the interface. If CEF is enabled but distributed CEF(dCEF) is disabled then CEF is in cefEnabled(1) state. If distributed CEF is enabled, then CEF is in distCefEnabled(2) sta…	Enumerationr/w Enumerated Values: 1 cefEnabled 2 distCefEnabled 3 cefDisabled	.1.3.6.1.4.1.9.9.492.1.5.1.1.1
cefIntLoadSharing The status of load sharing on the interface. perPacket(1) : Router to send data packets over successive equal-cost paths without regard to individual hosts or …	Enumerationr/w Enumerated Values: 1 perPacket 2 perDestination	.1.3.6.1.4.1.9.9.492.1.5.1.1.2
cefIntNonrecursiveAccouting The CEF accounting mode for the interface. CEF prefix based non-recursive accounting on an interface can be configured to store the stats for non-recursive prefixes in a internal or external bucket. in…	Enumerationr/w Enumerated Values: 1 internal 2 external	.1.3.6.1.4.1.9.9.492.1.5.1.1.3

Entity acting as RP (Routing Processor) keeps
the CEF states for the line card entities and
communicates with the line card entities using
XDR. This Table contains the CEF information 
related to peer entities on the managed device.

cefPeerEntry row .1.3.6.1.4.1.9.9.492.1.6.1.1

If CEF is enabled on the Managed device,
each entry contains the CEF related attributes
associated with a CEF peer entity.

entPhysicalIndex and entPeerPhysicalIndex are
also indexes for this table which re…

Indexes

ENTITY-MIBentPhysicalIndex entPeerPhysicalIndex

Column	Syntax	OID
entPeerPhysicalIndex The entity index for the CEF peer entity. Only the entities of 'module' entPhysicalClass are included here.	ENTITY-MIBPhysicalIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.9.9.492.1.6.1.1.1
cefPeerOperState The current CEF operational state of the CEF peer entity. Cef peer entity oper state will be peerDisabled(1) in the following condition: : Cef Peer entity encounters fatal error i.e. re…	Enumeration Enumerated Values: 1 peerDisabled 2 peerUp 3 peerHold	.1.3.6.1.4.1.9.9.492.1.6.1.1.2
cefPeerNumberOfResets Number of times the session with CEF peer entity has been reset.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.6.1.1.3

Entity acting as RP (Routing Processor) keep
the CEF FIB states for the line card entities and
communicate with the line card entities using
XDR. This Table contains the CEF FIB State 
related to peer entities on the managed device.

cefPeerFIBEntry row .1.3.6.1.4.1.9.9.492.1.6.2.1

If CEF is enabled on the Managed device,
each entry contains the CEF FIB State
associated a CEF peer entity.

entPhysicalIndex and entPeerPhysicalIndex are
also indexes for this table which represents
entit…

Indexes

ENTITY-MIBentPhysicalIndex entPeerPhysicalIndex cefFIBIpVersion

Column	Syntax	OID
cefPeerFIBOperState The current CEF FIB Operational State for the CEF peer entity.	Enumeration Enumerated Values: 1 peerFIBDown 2 peerFIBUp 3 peerFIBReloadRequest 4 peerFIBReloading 5 peerFIBSynced	.1.3.6.1.4.1.9.9.492.1.6.2.1.1

This table contains CEF consistency checker
(CC) global parameters for the managed device.

cefCCGlobalEntry row .1.3.6.1.4.1.9.9.492.1.7.1.1

If the managed device supports CEF,
each entry contains the global consistency
checker parameter for the managed device.
A row may exist for each IP version type
(v4 and v6) depending upon the IP version
supported on t…

Indexes

cefFIBIpVersion

Column	Syntax	OID
cefCCGlobalAutoRepairEnabled Once an inconsistency has been detected, CEF has the ability to repair the problem. This object indicates the status of auto-repair function for the consistency checkers.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.492.1.7.1.1.1
cefCCGlobalAutoRepairDelay Indiactes how long the consistency checker waits to fix an inconsistency. The value of this object has no effect when the value of object cefCCGlobalAutoRepairEnabled is 'false'.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.7.1.1.2
cefCCGlobalAutoRepairHoldDown Indicates how long the consistency checker waits to re-enable auto-repair after auto-repair runs. The value of this object has no effect when the value of object cefCCGlobalAutoRepairEnabled is 'false'.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.7.1.1.3
cefCCGlobalErrorMsgEnabled Enables the consistency checker to generate an error message when it detects an inconsistency.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.492.1.7.1.1.4
cefCCGlobalFullScanAction Setting the value of this object to ccActionStart(1) will start the full scan consistency checkers. The Management station should poll the cefCCGlobalFullScanStatus object to get the state of full-scan …	CISCO-CEF-TCCefCCActionr/w Type Values: 1 ccActionStart 2 ccActionAbort 3 ccActionNone	.1.3.6.1.4.1.9.9.492.1.7.1.1.5
cefCCGlobalFullScanStatus Indicates the status of the full scan consistency checker request.	CISCO-CEF-TCCefCCStatus Type Values: 1 ccStatusIdle 2 ccStatusRunning 3 ccStatusDone	.1.3.6.1.4.1.9.9.492.1.7.1.1.6

This table contains CEF consistency
checker types specific parameters on the managed device.
          
All detected inconsistency are signaled to the
Management Station via cefInconsistencyDetection
notification.

cefCCTypeEntry row .1.3.6.1.4.1.9.9.492.1.7.2.1

If the managed device supports CEF,
each entry contains the consistency
checker statistics for a consistency
checker type.
A row may exist for each IP version type
(v4 and v6) depending upon the IP version
supported o…

Indexes

cefFIBIpVersion cefCCType

Column	Syntax	OID
cefCCType Type of the consistency checker.	CISCO-CEF-TCCefCCType Type Values: 1 lcDetect 2 scanFibLcRp 3 scanFibRpLc 4 scanRibFib 5 scanFibRib 6 scanFibHwSw 7 scanFibSwHw 8 fullScanRibFib 9 fullScanFibRib 10 fullScanFibRpLc 11 fullScanFibLcRp 12 fullScanFibHwSw 13 fullScanFibSwHw	.1.3.6.1.4.1.9.9.492.1.7.2.1.1
cefCCEnabled Enables the passive consistency checker. Passive consistency checkers are disabled by default. Full-scan consistency checkers are always enabled. An attempt to set this object to 'false' for an active con…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.492.1.7.2.1.2
cefCCCount The maximum number of prefixes to check per scan. The default value for this object depends upon the consistency checker type. The value of this object will be irrelevant for some of the …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.7.2.1.3
cefCCPeriod The period between scans for the consistency checker.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.7.2.1.4
cefCCQueriesSent Number of prefix consistency queries sent to CEF forwarding databases by this consistency checker.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.7.2.1.5
cefCCQueriesIgnored Number of prefix consistency queries for which the consistency checks were not performed by this consistency checker. This may be because of some internal error or resource failure.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.7.2.1.6
cefCCQueriesChecked Number of prefix consistency queries processed by this consistency checker.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.7.2.1.7
cefCCQueriesIterated Number of prefix consistency queries iterated back to the master database by this consistency checker.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.7.2.1.8

This table contains CEF inconsistency
records.

cefInconsistencyRecordEntry row .1.3.6.1.4.1.9.9.492.1.7.3.1

If the managed device supports CEF,
each entry contains the inconsistency
record.

Indexes

cefFIBIpVersion cefInconsistencyRecId

Column	Syntax	OID
cefInconsistencyRecId The locally arbitrary, but unique identifier associated with this inconsistency record entry.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.492.1.7.3.1.1
cefInconsistencyPrefixType The network prefix type associated with this inconsistency record.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.492.1.7.3.1.2
cefInconsistencyPrefixAddr The network prefix address associated with this inconsistency record. The type of this address is determined by the value of the cefInconsistencyPrefixType object.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.492.1.7.3.1.3
cefInconsistencyPrefixLen Length in bits of the inconsistency address prefix.	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.9.9.492.1.7.3.1.4
cefInconsistencyVrfName Vrf name associated with this inconsistency record.	MPLS-VPN-MIBMplsVpnId Type Constraints: range: 0..31	.1.3.6.1.4.1.9.9.492.1.7.3.1.5
cefInconsistencyCCType The type of consistency checker who generated this inconsistency record.	CISCO-CEF-TCCefCCType Type Values: 1 lcDetect 2 scanFibLcRp 3 scanFibRpLc 4 scanRibFib 5 scanFibRib 6 scanFibHwSw 7 scanFibSwHw 8 fullScanRibFib 9 fullScanFibRib 10 fullScanFibRpLc 11 fullScanFibLcRp 12 fullScanFibHwSw 13 fullScanFibSwHw	.1.3.6.1.4.1.9.9.492.1.7.3.1.6
cefInconsistencyEntity The entity for which this inconsistency record was generated. The value of this object will be irrelevant and will be set to 0 when the inconsisency record is applicable for all the entities.	CISCO-TCEntPhysicalIndexOrZero Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.492.1.7.3.1.7
cefInconsistencyReason The reason for generating this inconsistency record. missing(1): the prefix is missing checksumErr(2): checksum error was found unknown(3): reason is unknown	Enumeration Enumerated Values: 1 missing 2 checksumErr 3 unknown	.1.3.6.1.4.1.9.9.492.1.7.3.1.8

This table specifies the CEF stats based
on the Prefix Length.

cefStatsPrefixLenEntry row .1.3.6.1.4.1.9.9.492.1.8.1.1

If CEF is enabled on the Managed device
and if CEF accounting is set to enable
prefix length based accounting (value of
cefCfgAccountingMap object in the
cefCfgEntry is set to enable 'prefixLength'
accounting), each…

Indexes

ENTITY-MIBentPhysicalIndex cefFIBIpVersion cefStatsPrefixLen

Column	Syntax	OID
cefStatsPrefixLen Length in bits of the Destination IP prefix. As 0.0.0.0/0 is a valid prefix, hence 0 is a valid prefix length.	INET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.9.9.492.1.8.1.1.1
cefStatsPrefixQueries Number of queries received in the FIB database for the specified IP prefix length.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.8.1.1.2
cefStatsPrefixHCQueries Number of queries received in the FIB database for the specified IP prefix length. This object is a 64-bit version of cefStatsPrefixQueries.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.8.1.1.3
cefStatsPrefixInserts Number of insert operations performed to the FIB database for the specified IP prefix length.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.8.1.1.4
cefStatsPrefixHCInserts Number of insert operations performed to the FIB database for the specified IP prefix length. This object is a 64-bit version of cefStatsPrefixInsert.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.8.1.1.5
cefStatsPrefixDeletes Number of delete operations performed to the FIB database for the specified IP prefix length.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.8.1.1.6
cefStatsPrefixHCDeletes Number of delete operations performed to the FIB database for the specified IP prefix length. This object is a 64-bit version of cefStatsPrefixDelete.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.8.1.1.7
cefStatsPrefixElements Total number of elements in the FIB database for the specified IP prefix length.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.8.1.1.8
cefStatsPrefixHCElements Total number of elements in the FIB database for the specified IP prefix length. This object is a 64-bit version of cefStatsPrefixElements.	HCNUM-TCCounterBasedGauge64	.1.3.6.1.4.1.9.9.492.1.8.1.1.9

This table specifies the CEF switch stats.

cefSwitchingStatsEntry row .1.3.6.1.4.1.9.9.492.1.8.2.1

If CEF is enabled on the Managed device,
each entry specifies the switching stats.
A row may exist for each IP version type
(v4 and v6) depending upon the IP version
supported on the device.

entPhysicalInde…

Indexes

ENTITY-MIBentPhysicalIndex cefFIBIpVersion cefSwitchingIndex

Column	Syntax	OID
cefSwitchingIndex The locally arbitrary, but unique identifier associated with this switching stats entry.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.492.1.8.2.1.1
cefSwitchingPath Switch path where the feature was executed. Available switch paths are platform-dependent. Following are the examples of switching paths: RIB : switching with CEF assistance Low-end s…	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.9.9.492.1.8.2.1.2
cefSwitchingDrop Number of packets dropped by CEF.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.8.2.1.3
cefSwitchingHCDrop Number of packets dropped by CEF. This object is a 64-bit version of cefSwitchingDrop.	packetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.8.2.1.4
cefSwitchingPunt Number of packets that could not be switched in the normal path and were punted to the next-fastest switching vector.	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.8.2.1.5
cefSwitchingHCPunt Number of packets that could not be switched in the normal path and were punted to the next-fastest switching vector. This object is a 64-bit version of cefSwitchingPunt.	packetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.8.2.1.6
cefSwitchingPunt2Host Number of packets that could not be switched in the normal path and were punted to the host (process switching path). For most of the switching paths, the value of this object may be similar to cefSwitchi…	packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.492.1.8.2.1.7
cefSwitchingHCPunt2Host Number of packets that could not be switched in the normal path and were punted to the host (process switching path). For most of the switching paths, the value of this object may be similar to cefSwitchi…	packetsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.492.1.8.2.1.8