CISCO-CABLE-WIDEBAND-MIB Table View

This table contains attributes of the physical
RF channels. MPEG-TS packets are sent across RF
channels within a wideband channel.
          
These physical RF channels might be present on a
different system but the WCMTS entity requires
the knowledge of that system for its operation.

ccwbRFChannelEntry row .1.3.6.1.4.1.9.9.479.1.1.1

An entry provides a list of attributes for a single
downstream RF channel per WCMTS entity.

An entry in this table exists for each configured
RF channel on the WCMTS entity that provides the
wideband DOCSIS…

Indexes

ENTITY-MIBentPhysicalIndex ccwbRFChannelNum

Column	Syntax	OID
ccwbRFChannelNum The WCMTS identification of the RF channel. The range of this object is limited to 0-18 in the case of annex A/256qam, and 0-23 for Annex B and C.	Unsigned32 Constraints: range: 0-255	.1.3.6.1.4.1.9.9.479.1.1.1.1
ccwbRFChannelFrequencydeprecated The center of the downstream frequency associated with this RF channel. The final downstream RF frequency may be provided by an edge QAM device or the CMTS itself. See the associated compliance object for a description …	hertzUnsigned32r/w Constraints: range: 0-1000000000	.1.3.6.1.4.1.9.9.479.1.1.1.2
ccwbRFChannelWidth The bandwidth of this downstream RF channel. Most implementations are expected to support a channel width of 6 MHz (North America) and/or 8 MHz (Europe). See the associated compliance object for a description of the val…	hertzUnsigned32r/w Constraints: range: 0-16000000	.1.3.6.1.4.1.9.9.479.1.1.1.3
ccwbRFChannelModulation The modulation type associated with this downstream RF channel. See the associated conformance object for write conditions an limitations. See the DOCSIS specification for specifics on the modulation profiles implied by…	Enumerationr/w Enumerated Values: 1 qam64 2 qam256 3 qam1024	.1.3.6.1.4.1.9.9.479.1.1.1.4
ccwbRFChannelAnnex The value of this object indicates the conformance of the implementation to important regional cable standards. annexA : Annex A from ITU-J83 is used. annexB : Annex B from ITU-J83 is used. annexC : Annex C from ITU-J83…	Enumerationr/w Enumerated Values: 1 annexA 2 annexB 3 annexC	.1.3.6.1.4.1.9.9.479.1.1.1.5
ccwbRFChannelMpegPkts The number of MPEG packets transmitted on this RF channel.	PacketsSNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.479.1.1.1.6
ccwbRFChannelStorageType The storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.479.1.1.1.7
ccwbRFChannelRowStatus Controls and reflects the status of rows in this table. It can be used for creating and deleting entries in this table. The ccwbRFChannelAnnex and ccwbRFChannelModulation must be valid for a row to be cre…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.479.1.1.1.8
ccwbRFChannelUtilization The calculated and truncated utilization for this RF channel over the previous complete measuring interval. The configured duration of the measurement intervals is defined in the ccwbRFChanUtilInterval object. …	percentUnsigned32 Constraints: range: 0-100	.1.3.6.1.4.1.9.9.479.1.1.1.9
ccwbRFChannelFrequencyRev1 The center of the downstream frequency associated with this RF channel. The final downstream RF frequency may be provided by an edge QAM device or the CMTS itself. See the associated compliance object for a description …	hertzUnsigned32r/w Constraints: range: 55000000-1050000000	.1.3.6.1.4.1.9.9.479.1.1.1.10

This table contains information of the external edge QAM
which provide the physical RF channels which are available
to the wideband channels.

ccwbRFChannelQamEntry row .1.3.6.1.4.1.9.9.479.1.2.1

An entry provides a list of attributes for a single
RF channel which can be physically present on an external
edge QAM device.

An entry in this table exists for each configured
RF channel on the WCMTS modul…

Indexes

No indexes recorded

Column	Syntax	OID
ccwbRFChanQamIPAddressType The type of internet address. This object identifies the internet address type specified by ccwbRFChanQamIPAddress object.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.9.9.479.1.2.1.1
ccwbRFChanQamIPAddress The IP address of the edge QAM device or the CMTS cable interface which provides the physical RF channel. The IP address will be of the type represented by object ccwbRFChanQamIPAddressType.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.479.1.2.1.2
ccwbRFChanQamMacAddress The MAC address of the edge QAM device or next hop router which might be present between the WCMTS and the edge QAM.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.479.1.2.1.3
ccwbRFChanQamUdpPort The port number on the edge QAM associated with this RF channel.	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.479.1.2.1.4
ccwbRFChanQamTos The value of the TOS field in the IP header for all Ethernet frames destined for the given RF channel.	Unsigned32r/w Constraints: range: 0-255	.1.3.6.1.4.1.9.9.479.1.2.1.5
ccwbRFChanQamVlanId The VLAN ID to be inserted in the Ethernet frames when using 802.1q frames instead of normal 802.1 frames for the given RF channel. The value of 0 indicates that 802.1 frames are being used and is not supported in setti…	Unsigned32r/w Constraints: range: 0-4095	.1.3.6.1.4.1.9.9.479.1.2.1.6
ccwbRFChanQamPriorityBits The priority bits used when inserting Ethernet 802.1q VLAN tags into the Ethernet frames destined for a given RF channel. Priority Bits (0=Best effort, 1=background, 2=spare, 3=excellent effort, 4=controlled load, 5=vid…	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.9.9.479.1.2.1.7
ccwbRFChanQamDepiRemoteId The DEPI remote ID on edge QAM associated with this RF channel.	Unsigned32r/w Constraints: range: 1-4294967295	.1.3.6.1.4.1.9.9.479.1.2.1.8
ccwbRFChanQamDepiTunnel This object specifies the name of the DEPI tunnel which determines the DEPI data session configuration associated with this RF channel.	OctetStringr/w Constraints: range: 0-255	.1.3.6.1.4.1.9.9.479.1.2.1.9
ccwbRFChanQamTsid This object specifies the MPEG2 transport stream ID which is associated with this RF channel.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.9.9.479.1.2.1.10

A wideband channel is a logical grouping of one or more
physical RF channels over which Wideband MPEG-TS packets
are carried.
          
This table contains association information of the wideband
channels to the RF channels that are available for the WCMTS.

ccwbWBtoRFMappingEntry row .1.3.6.1.4.1.9.9.479.1.3.1

An entry provides a list of attributes for a single
association between a wideband channel and a RF channel.

An entry in this table exists for each association
between a wideband channel and RF channel on t…

Indexes

IF-MIBifIndex ENTITY-MIBentPhysicalIndex ccwbRFChannelNum

Column	Syntax	OID
ccwbWBtoRFBandwidth The percentage of the RF channel bandwidth allocated for this wideband channel.	percentUnsigned32r/w Constraints: range: 1-100	.1.3.6.1.4.1.9.9.479.1.3.1.1
ccwbWBtoRFStorageType The storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.479.1.3.1.2
ccwbWBtoRFRowStatus Controls and reflects the status of rows in this table. It can be used for creating and deleting entries in this table. The ccwbWBtoRFBandwidth must be valid for a row to be created. When ccwbWBtoRFRowSta…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.479.1.3.1.3

This table contains information of the mapping
of the wideband channels to the Narrowband channels
that are available on the WCMTS.
          
The wideband protocol utilizes the existing narrowband
downstream channel for carrying the MAC management and
signaling messages and the associated narrowband upstream
for return data traffic and signaling.

ccwbWBtoNBMappingEntry row .1.3.6.1.4.1.9.9.479.1.4.1

An entry provides a list of attributes for a
association between a wideband channel and a narrowband
channel.

An entry in this table exists for each association
between a wideband channel and narrowband cha…

Indexes

IF-MIBifIndex ccwbWBtoNBifIndexForNB

Column	Syntax	OID
ccwbWBtoNBifIndexForNB The ifIndex of the narrowband cable interface associated with this wideband channel.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.479.1.4.1.1
ccwbWBtoNBStorageType The storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.479.1.4.1.2
ccwbWBtoNBRowStatus Controls and reflects the status of rows in this table. It can be used for creating and deleting entries in this table. The object ccwbWBtoNBifIndexForNB must be valid in order for row to be created.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.479.1.4.1.3

This table provides information about a
Wideband BG interface, whether its configured
to carry multicast or non-multicast traffic.
For multicast the BG interface type is
Secondary and for non-multicast its non-Secondary.
Other objects could be added to this later in
the future.

ccwbWBBondGrpEntry row .1.3.6.1.4.1.9.9.479.1.5.1

An entry in this table provides information
about each Wideband BG interface whose ifType is
ciscoDocsCableWBDownstream(224).

Indexes

IF-MIBifIndex

Column	Syntax	OID
ccwbWBBondGrpSecondary This object has the value 'true(1)' if the WB interface(BG) is Seconday and the value 'false(2)' for non-Secondary.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.479.1.5.1.1

This table contains Wideband Cable Modem(WCM) connectivity state.
A WCM connectivity state can be associated with multiple
Wideband interfaces.

ccwbWBCmStatusEntry row .1.3.6.1.4.1.9.9.479.1.6.1

Status information for a single Wideband Cable Modem.
An entry in this table exists for each Wideband Cable Modem
that is connected to the WCMTS.

Indexes

DOCS-IF-MIBdocsIfCmtsCmStatusIndex

Column	Syntax	OID
ccwbWBCmStatusValue Current WB Cable Modem connectivity state, as specified in the RF Interface Specification. Returned status information is the WCM status as assumed by the WCMTS, and indicates the following events: The en…	Enumeration Enumerated Values: 1 offline 2 others 3 initRangingRcvd 4 initDhcpReqRcvd 5 onlineNetAccessDisabled 6 onlineKekAssigned 7 onlineTekAssigned 8 rejectBadMic 9 rejectBadCos 10 kekRejected 11 tekRejected 12 online 13 initTftpPacketRcvd 14 initTodRequestRcvd 15 reset 16 rangingInProgress 17 dhcpGotIpAddr 18 rejStaleConfig 19 rejIpSpoof 20 rejClassFail 21 rejRegNack 22 bpiKekExpired 23 bpiTekExpired 24 shutdown 25 channelChgInitRangingRcvd 26 channelChgRangingInProgress 27 wbOnline 28 wbOnlinePrivacy 29 wbOnlineKekAssigned 30 wbOnlineTekAssigned 31 wbOnlineNetAccessDis 32 wbKekReject 33 wbTekReject 34 wbNetAccessDisReject 35 wbPrivacyEnabReject 36 wbKekExpire 37 wbTekExpire 38 wbNetAccessDisExpire 39 wbPrivacyEnabExpire	.1.3.6.1.4.1.9.9.479.1.6.1.1

An entry in this table exists for each Wideband
Cable Modem which links to one or more WB interface.

ccwbWBCmStatusExtEntry row .1.3.6.1.4.1.9.9.479.1.7.1

This entry exists for each Wideband Cable Modem(WCM)
which links to one or more WB interface.

Indexes

DOCS-IF-MIBdocsIfCmtsCmStatusIndex ccwbWBCmStatusExtIndex

Column	Syntax	OID
ccwbWBCmStatusExtIndex The value of this object uniquely identifies an association between a WCM and a BG.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.479.1.7.1.1
ccwbWBCmWBIfindex ifIndex of the wideband channel associated with the WCM.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.479.1.7.1.2

This table contains the description of a Fiber Node
on a CMTS. An entry in this table exists for each
FiberNode ID.

ccwbFiberNodeDescrEntry row .1.3.6.1.4.1.9.9.479.1.8.1

This entry provides the description of each fiber node
on the CMTS and it is part of the Fiber node configuration.

Indexes

ccwbFiberNodeID

Column	Syntax	OID
ccwbFiberNodeDescription This object contains the user configured description string of the fiber node.	OctetStringr/w Constraints: range: 1-80	.1.3.6.1.4.1.9.9.479.1.8.1.1
ccwbFiberNodeDescrStorageType The storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.479.1.8.1.2
ccwbFiberNodeDescrRowStatus Controls and reflects the status of rows in this table. It can be used for creating and deleting entries in this table. ccwbFiberNodeDescription must not be null in order for row to be created.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.479.1.8.1.3

This table provides configuration information of each Fiber node.
It will provide topology information of each Fiber node, which
includes information such as, Narrowband and Wideband QAMs.

ccwbFiberNodeEntry row .1.3.6.1.4.1.9.9.479.1.9.1

An entry in this table exists for each FiberNode ID that is in use.
It uses two indices, i.e. ccwbFiberNodeID which is the
Fiber node ID, and ccwbFiberNodeGlobRFID, which is the combined
bit mask of Narrowband RF channe…

Indexes

ccwbFiberNodeID ccwbFiberNodeGlobRFID

Column	Syntax	OID
ccwbFiberNodeID This object represents the Fiber node ID. Each Fiber node configuration on the CMTS is assigned a unique Fiber node ID.	Unsigned32 Constraints: range: 1-1000	.1.3.6.1.4.1.9.9.479.1.9.1.1
ccwbFiberNodeGlobRFID This is the RF ID of both Narrowband and Wideband QAMs(rf-channels) combined.	Unsigned32 Constraints: range: 0-1024	.1.3.6.1.4.1.9.9.479.1.9.1.2
ccwbFiberNodeNBIfIndx This object represents the Narrowband Ifindex of the RF downstream channel which is part of the Fiber node configuation.	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.9.9.479.1.9.1.3
ccwbFiberNodeWBContlrPhyIndx This object represents the entity physical index of Wideband controller card. This card contains the RF port which is part of the ccwbFiberNodeGlobRFID bit mask. A value of zero means the index is invalid. ccwbFiberNode…	ENTITY-MIBPhysicalIndexOrZeror/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.479.1.9.1.4
ccwbFiberNodeWBRFPort This object represents the RF downstream channel IDs (rf-ports) of the wideband controller card. Each Wideband controller can have 24 RF channels. ccwbFiberNodeWBRFPort and ccwbFiberNodeWBContlrPhyIndx are mutually incl…	Integer32r/w Constraints: range: 0-1024	.1.3.6.1.4.1.9.9.479.1.9.1.5
ccwbFiberNodeStorageType The storage type for this conceptual row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.9.9.479.1.9.1.6
ccwbFiberNodeRowStatus Controls and reflects the status of rows in this table. It can be used for creating and deleting entries in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.479.1.9.1.7