CISCO-ATM-SIG-DIAG-MIB Table View

The table whose entries describe the filtering criteria 
for recording failed connection setup requests.

csfFilterEntry row .1.3.6.1.4.1.9.9.78.1.2.1.1

Each entry in this table corresponds to a filtering criteria
based on which the rejected calls are recorded. This selection
criteria is applied against all connection setup failures
generated/detected at this ATM dev…

Indexes

csfFilterIndex

Column	Syntax	OID
csfFilterIndex An arbitrary integer uniquely identifying a filtering criteria.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.9.9.78.1.2.1.1.1
csfFilterScope This object restricts the scope of the filter to calls which where rejected either within the system in which the filtering is in progress or to calls which were rejected on external ATM devices but transited throug…	Enumerationr/w Enumerated Values: 1 localRejects 2 remoteRejects 3 allRejects	.1.3.6.1.4.1.9.9.78.1.2.1.1.2
csfFilterConnKind This object enables the user to track failures of soft permanent virtual channel connections, soft permanent virtual path connections, switched virtual channel connections, and/or switched virtual path connections.	OctetStringr/w Constraints: range: 1-1	.1.3.6.1.4.1.9.9.78.1.2.1.1.3
csfFilterConnCastType This object restricts the scope of the filter based on the type of topology of connections (point-to-point or point-to-multipoint).	OctetStringr/w Constraints: range: 1-1	.1.3.6.1.4.1.9.9.78.1.2.1.1.4
csfFilterServiceCategory This object restricts the scope of the filter to calls belonging to service categories represented by this object.	OctetStringr/w Constraints: range: 1-1	.1.3.6.1.4.1.9.9.78.1.2.1.1.5
csfFilterInInterface This object restricts the scope of the filter to calls which entered the ATM device through the port represented by this object It has the value 0, or the ifIndex value of an ATM Interface. The value zero indicates that…	CISCO-TCInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.78.1.2.1.1.6
csfFilterOutInterface This object restricts the scope of the filter to calls which exited the ATM device through the port represented by this object It has the value 0, or the ifIndex value of an ATM Interface. The value zero indicates that …	CISCO-TCInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.78.1.2.1.1.7
csfFilterCause This object restricts the scope of the filter to calls which were cleared with the cause code represented by this object. The values are the same as the clear code values mentioned in the ATM forum UNI specifications.T…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.9.9.78.1.2.1.1.8
csfFilterCallingParty The combination of this object and the corresponding instance of csfFilterCallingPartyMask is one selection criteria for this record. To match this selection criteria, a failed connection setup must have a Calling P…	AtmAddrr/w Type Constraints: range: 0 range: 8 range: 20	.1.3.6.1.4.1.9.9.78.1.2.1.1.9
csfFilterCallingPartyMask The combination of this object and the corresponding instance of csfFilterCallingParty is one selection criteria for this record. To match this selection criteria, a failed connection setup must have a Calling Party…	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.9.9.78.1.2.1.1.10
csfFilterCalledParty The combination of this object and the corresponding instance of csfFilterCalledPartyMask is one selection criteria for this record. To match this selection criteria, a failed connection setup must have a called par…	AtmAddrr/w Type Constraints: range: 0 range: 8 range: 20	.1.3.6.1.4.1.9.9.78.1.2.1.1.11
csfFilterCalledPartyMask The combination of this object and the corresponding instance of csfFilterCalledParty is one selection criteria for this record. To match this selection criteria, a failed connection setup must have a Calling Party …	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.9.9.78.1.2.1.1.12
csfFilterMaxRecords The maximum number of entries that are desired in the csfRecordTable on behalf of this entry. The agent will not create more than this number of entries in the table,but may choose to create fewer entries in the csfRec…	Integer32r/w Constraints: range: -1-214783647	.1.3.6.1.4.1.9.9.78.1.2.1.1.13
csfFilterAgeTimeout The number of seconds left for this entry to age out. On expiry of this timer filtering is disabled for this entry. The display records in the csfRecordTable corresponding to this entry are retained. When the timer ex…	secondsInteger32r/w Constraints: range: -1-2147483647	.1.3.6.1.4.1.9.9.78.1.2.1.1.14
csfFilterPurge The object provides a facility for the user to purge the records in the csfRecordTable corresponding to this entry. When the value is set to 'purge', the records in the csfRecordTable corresponding to this entry are…	Enumerationr/w Enumerated Values: 1 purge 2 noop	.1.3.6.1.4.1.9.9.78.1.2.1.1.15
csfFilterNumMatches A monotonically increasing counter to keep track of the number of call failures that matched this entry for the entire lifetime of this entry.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.78.1.2.1.1.16
csfFilterRowStatus Indicates the status of this row. Used according to the row installation and removal conventions. This object can be used to temporarily inactivate an entry in the table. When this object is set to a value 'notInServi…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.78.1.2.1.1.17

The table in which the failures of ATM Signalling connection 
setup requests are recorded.

csfRecordEntry row .1.3.6.1.4.1.9.9.78.1.3.1.1

An entry representing one connection setup request failure
record. The csfRecordFilterIndex represents the
index into the csfFilterTable whose entry is the
filtering criteria applied against all connection setup
fa…

Indexes

csfFilterIndex csfRecordIndex

Column	Syntax	OID
csfRecordIndex An arbitrary integer used to distinguish between multiple records for the same filtering criteria.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.78.1.3.1.1.1
csfRecordScope This object indicates the location of the call failure.	Enumeration Enumerated Values: 1 localReject 2 remoteReject	.1.3.6.1.4.1.9.9.78.1.3.1.1.2
csfRecordConnKind This object represents the use of call control of the rejected connection.	Enumeration Enumerated Values: 1 softPvcc 2 softPvpc 3 switchedVcc 4 switchedVpc	.1.3.6.1.4.1.9.9.78.1.3.1.1.3
csfRecordConnCastType This object represents the type of topology of the rejected call (point-to-point or point-to-multipoint).	Enumeration Enumerated Values: 1 p2p 2 p2mp	.1.3.6.1.4.1.9.9.78.1.3.1.1.4
csfRecordConnIndicator Indicates whether this record was created due to an add party failure or a setup failure.	Enumeration Enumerated Values: 1 addPartyReject 2 setupReject	.1.3.6.1.4.1.9.9.78.1.3.1.1.5
csfRecordServiceCategory This object represents the service category used by the call.	PNNI-MIBServiceCategory Type Values: 1 other 2 cbr 3 rtVbr 4 nrtVbr 5 abr 6 ubr	.1.3.6.1.4.1.9.9.78.1.3.1.1.6
csfRecordInInterface The IfIndex of the incoming port on which this call was received by the ATM device.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.78.1.3.1.1.7
csfRecordOutInterface The IfIndex of the outgoing port ,if available, through which this call was routed to the network. The distinguished value zero indicates that the call was rejected before any outgoing interface was chosen.	CISCO-TCInterfaceIndexOrZero Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.78.1.3.1.1.8
csfRecordCause This object identifies the reason for the call failure. When a PNNI Crankback information element is included in the call clearing message, this object contains the crankback cause. In all other cases, the values are…	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.9.9.78.1.3.1.1.9
csfRecordDiags This object contains the contents of the diagnostics fields from the Cause information element. When the value of csfRecordCause is 49,'Quality of Service unavailable', the diagnostics are taken from the PNNI Crankba…	OctetString Constraints: range: 0-17	.1.3.6.1.4.1.9.9.78.1.3.1.1.10
csfRecordCallingParty Indicates the ATM adddress of the calling party in the rejected call.	AtmAddr Type Constraints: range: 0 range: 8 range: 20	.1.3.6.1.4.1.9.9.78.1.3.1.1.11
csfRecordCallingPartySubAddress Indicates the ATM sub-adddress of the calling party in the rejected call. The presence of a sub address is not mandatory. If the calling sub-addresses is not present in the call then this object will have a null value.	AtmAddr Type Constraints: range: 0 range: 8 range: 20	.1.3.6.1.4.1.9.9.78.1.3.1.1.12
csfRecordCalledParty Indicates the ATM address of the called party in the rejected call.	AtmAddr Type Constraints: range: 0 range: 8 range: 20	.1.3.6.1.4.1.9.9.78.1.3.1.1.13
csfRecordCalledPartySubAddress Indicates the ATM sub-adddress of the called party in the rejected call. The presence of a sub address is not mandatory. If the called sub-address is not present in the call then this object will have a null value.	AtmAddr Type Constraints: range: 0 range: 8 range: 20	.1.3.6.1.4.1.9.9.78.1.3.1.1.14
csfRecordCrankBackTransitType This object identifies the type of blockage in case of a blocked call. This object has a value 'noCrankBack' if the call was cleared without a crankback information element.	Enumeration Enumerated Values: 1 blockedIncomingPort 2 blockedNode 3 blockedLink 4 noCrankBack	.1.3.6.1.4.1.9.9.78.1.3.1.1.15
csfRecordCrankBackNodeId This object depends on the csfRecordCrankBackTransitType object. When that object value is 'blockedNode', csfRecordCrankBackNodeId indicates the node ID of the blocked node. When the csfRecordCrankBackTransitType objec…	PNNI-MIBPnniNodeId Type Constraints: range: 22	.1.3.6.1.4.1.9.9.78.1.3.1.1.16
csfRecordCrankBackPortId When the csfRecordCrankBackTransitType object value is 'blockedLink', this object identifies a logical port of the blocked link's preceeding node identifier. The distinguished value zero indicates that no port is sp…	PNNI-MIBPnniPortId	.1.3.6.1.4.1.9.9.78.1.3.1.1.17
csfRecordCrankBackSucceedingNodeId This object depends on the csfRecordCrankBackTransitType object. If the csfRecordCrankBackNodeId object value is 'blockedLink' then the value of this object will identify the logical node succeeding a link at which the…	PNNI-MIBPnniNodeId Type Constraints: range: 22	.1.3.6.1.4.1.9.9.78.1.3.1.1.18
csfRecordTimeStamp The time at which this record entry was created.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.78.1.3.1.1.19

The table in which the Designated Transit List (DTL)stacks 
(i.e., source routes) of failed calls  are recorded. Each DTL 
identifies a source route through a single peer group. 
DTL's are represented as a series of logical Node IDs and 
logical Port IDs.

csfDtlEntry row .1.3.6.1.4.1.9.9.78.1.3.2.1

A segment of the DTL stack. The complete DTL stack is formed
by traversing the rows of the table for which the csfFilterIndex
and csfRecordIndex are the same. Level transitions are indicated
using the csfDtlLinkType.…

Indexes

csfFilterIndex csfRecordIndex csfDtlEntryIndex

Column	Syntax	OID
csfDtlEntryIndex The index in the current DTL stack of this entry. This index represents the the order of this entry in the DTL stack.	Integer32 Constraints: range: 1-200	.1.3.6.1.4.1.9.9.78.1.3.2.1.1
csfDtlNodeId Each entry in the DTL table corresponds to a node/port tuple based on which a source route through the peer group is built. This object represents the node id in the tuple	PNNI-MIBPnniNodeId Type Constraints: range: 22	.1.3.6.1.4.1.9.9.78.1.3.2.1.2
csfDtlPortId Each entry in the DTL table corresponds to a node/port tuple based on which a source route through the peer group is built. This object represents the port id in the tuple	PNNI-MIBPnniPortId	.1.3.6.1.4.1.9.9.78.1.3.2.1.3
csfDtlLinkType The type of link out from the node identified by csfDtlNodeId. This is well defined even if the specific port is not specified. A value 'horizontal' indicates a normal link within the containing peer group. A value …	Enumeration Enumerated Values: 1 invalid 2 horizontal 3 uplink 4 last	.1.3.6.1.4.1.9.9.78.1.3.2.1.4