CERAGON-MIB Table View

This table contains general configuration info
per device, local and remote.

gnGenCfgDeviceEntry row .1.3.6.1.4.1.2281.2.1.8.1

Entry containing general configuration information, for both local and
remote sides.

Indexes

gnGenCfgDeviceId

Column	Syntax	OID
gnGenCfgDeviceIdmandatory This value indicates the device table entry (local or Remote).	Enumeration Enumerated Values: 1 local 2 remote	.1.3.6.1.4.1.2281.2.1.8.1.1
gnGenCfgDeviceResetPerfMonmandatory Reset performance monitoring.	Enumerationr/w Enumerated Values: 2 reset 3 noAction 4 clearFastEthernetStatistics	.1.3.6.1.4.1.2281.2.1.8.1.2
gnGenCfgDeviceOperationmandatory This parameter allows the NMS to perform operations. (3) will implement software RESET (4) will SET all factory default configurations, including IP address! (5) will CLEAR IDU software NOTE: CLEARING IDU software wil…	Enumerationr/w Enumerated Values: 2 noOperation 3 softwareReset 4 setDefaultConf 5 clearMainManagerSoftware 6 resetODU 7 resetMUX 8 resetSwOdu	.1.3.6.1.4.1.2281.2.1.8.1.3
gnGenCfgActivateLoopbackmandatory This parameter controls the loop back diagnostics operations. For remote units, only SPI, MUX and MDM loopbacks are allowed.	Enumerationr/w Enumerated Values: 2 noOperation 3 loopbackSPI 5 loopbackMDM 6 loopbackOuterSPI 10 localODUloopback	.1.3.6.1.4.1.2281.2.1.8.1.4
gnGenCfgF1DataChanConnectormandatory This is the physical interface of the F1 line data channel (USER CHANNEL connection).	Enumeration Enumerated Values: 1 noInterface 2 rs232db25 3 v35 4 rs422db25 5 rj45CoDirect 6 rj45bridge 7 x21db15 8 rs232db9	.1.3.6.1.4.1.2281.2.1.8.1.5
gnGenCfgWaySideConnectormandatory This is the physical interface of the radio E1 way side channel (WAYSIDE CHANNEL connection).	Enumeration Enumerated Values: 1 noInterface 2 rs232db25 3 v35 4 rs422db25 5 connectorE1 6 rj45bridge 7 x21db15 8 connectorT1 9 lineSTM4 10 clockUnit2M 11 clockUnit1dot5M	.1.3.6.1.4.1.2281.2.1.8.1.6
gnGenCfgActivateChanLoopbackmandatory This parameter controls the USER CHANNEL and WAYSIDE channel loopback diagnostic operations. (3) will activate the 64k data channel loopback (USER CHANNEL) (4) will activate the WAYSIDE CHANNEL loopback.	Enumerationr/w Enumerated Values: 2 noOperation 3 loopbackDataChan 4 loopbackWaySide	.1.3.6.1.4.1.2281.2.1.8.1.7
gnGenCfgInterLenLocalOnlymandatory This field is the FEC interleaver length .DONT CAHNGE THIS FIELD !!! . WRITE will change the local side only.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.1.8.1.8
gnGenCfgSlipIpmandatory This is the SERIAL interface IP address. Included for future development, not currently supported.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2281.2.1.8.1.9
gnGenCfgSlipModemConnectionmandatory The telephone number to which the modem will initialize a call, upon generation of a TRAP. The number must be entered numerically (for example 18001234567).	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.2281.2.1.8.1.10
gnGenCfgSlipSpeedmandatory The SERIAL interface baud rate.	Enumerationr/w Enumerated Values: 1 baud9600 2 baud19200 3 baud38400 4 baud57600 5 baud115200	.1.3.6.1.4.1.2281.2.1.8.1.11
gnGenCfgAlarmSeveritymandatory This field is used only by the element management application Every Trap severity 4 bits. 15 (MAJOR), 7 (MINOR), 3 (WARNING) and 1 (EVENT) options. The first 4 bits ODU Power supply severity, then the Synthesizer severi…	OctetStringr/w Constraints: range: 15-15	.1.3.6.1.4.1.2281.2.1.8.1.12
gnGenCfgODUSerialNumbermandatory This is the ODU serial number - up to 20 characters	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.2281.2.1.8.1.13
gnGenCfgIDUSerialNumbermandatory This is the IDU serial number - up to 20 characters	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.2281.2.1.8.1.14
gnGenCfgAlarmTextmandatory The private trap text, describing the last generated trap text.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2281.2.1.8.1.15
gnGenCfgTrapSeveritymandatory The current Trap severity, describing the last generated trap severity	Enumeration Enumerated Values: 0 clear 1 event 3 warning 7 minor 15 major 31 critical	.1.3.6.1.4.1.2281.2.1.8.1.16
gnGenCfgProductTypemandatory The product type.	Enumeration Enumerated Values: 2 accessMux 3 sdhRegenerator 4 narrowBandPdhRepeater 5 accessMuxStm0 6 plex6200 7 adm	.1.3.6.1.4.1.2281.2.1.8.1.17
gnGenCfgLeftMediumConnectormandatory For ACCESS hardware, this indicates the first (left) interface connector.	Enumeration Enumerated Values: 1 noInterface 2 twoDS3 3 oneDS3 4 twoE3 5 oneE3 6 oneFastEthernet 7 fiberSTM1 8 electricalSTM1 9 utpSTM1 10 stpSTM1 11 twoSTM1 12 eightE1 13 eightT1 14 hitLess 15 fiberSTM1Trib 16 electricalSTM1Trib 17 hitLessWithBridge 18 opticalFastEthernet	.1.3.6.1.4.1.2281.2.1.8.1.18
gnGenCfgMiddleMediumConnectormandatory For ACCESS hardware, this indicates the second (right)interface connector.	Enumeration Enumerated Values: 1 noInterface 2 twoDS3 3 oneDS3 4 twoE3 5 oneE3 6 oneFastEthernet 7 fiberSTM1 8 electricalSTM1 9 utpSTM1 10 stpSTM1 11 twoSTM1 12 eightE1 13 eightT1 14 hitLess 15 fiberSTM1Trib 16 electricalSTM1Trib 17 hitLessWithBridge 18 opticalFastEthernet	.1.3.6.1.4.1.2281.2.1.8.1.19
gnGenCfgPrimaryClockSourcemandatory The primary clock source, configurable for ACCESS radios only.	Enumerationr/w Enumerated Values: 2 internalClock 3 external2MB 4 radioClock 5 fiberClock 6 external2MHz 7 external1AndHalfMB 8 tributaryClock1 9 tributaryClock2 10 tributaryClock3 11 tributaryClock4 12 tributaryClock5 13 tributaryClock6 14 tributaryClock7 15 tributaryClock8 16 tributaryClock9 17 tributaryClock10 18 tributaryClock11 19 tributaryClock12 20 tributaryClock13 21 tributaryClock14 22 tributaryClock15 23 tributaryClock16 24 tribSTM1	.1.3.6.1.4.1.2281.2.1.8.1.20
gnGenCfgSecondaryClockSourcemandatory The secondary clock source, configurable for ACCESS radios only.	Enumerationr/w Enumerated Values: 2 internalClock 3 external2MB 4 radioClock 5 fiberClock 6 external2MHz 7 external1AndHalfMB 8 tributaryClock1 9 tributaryClock2 10 tributaryClock3 11 tributaryClock4 12 tributaryClock5 13 tributaryClock6 14 tributaryClock7 15 tributaryClock8 16 tributaryClock9 17 tributaryClock10 18 tributaryClock11 19 tributaryClock12 20 tributaryClock13 21 tributaryClock14 22 tributaryClock15 23 tributaryClock16 24 tribSTM1	.1.3.6.1.4.1.2281.2.1.8.1.21
gnGenCfgTrapOptionmandatory This item defines various trap options (0-31): 0 - SNSN (STANDARD TRAPS DO NOT INCLUDE SERIAL NUMBER) 1 - ASN (ALL TRAPS INCLUDE SERIAL NUMBER) 2 - SNSN, DNLR (DO NOT REPORT LOCAL TRAPS FROM REMOTE IDU) …	Integer32r/w Constraints: range: 0-31	.1.3.6.1.4.1.2281.2.1.8.1.22
gnGenCfgCLLImandatory Common Language Location Identifier (maximum length: 30)	OctetStringr/w Constraints: range: 0-30	.1.3.6.1.4.1.2281.2.1.8.1.23
gnGenCfgHeartbeatPeriodmandatory This item defines the number of minutes between each trap	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2281.2.1.8.1.24
gnGenCfgGetRemoteDatamandatory .	Enumerationr/w Enumerated Values: 2 off 3 on	.1.3.6.1.4.1.2281.2.1.8.1.25
gnGenCfgClearLoopTimeoutmandatory This item defines the clear loopbacks timeout in minutes. possible values: 0..1440. 0 means disable.	Integer32r/w Constraints: range: 0-1440	.1.3.6.1.4.1.2281.2.1.8.1.26
gnGenCfgSubProductTypemandatory lsb bit: 1 if 1500i or 1528i 0 otherwise.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.1.8.1.27

This table contains general configuration info
per device; local and remote.

gnGenStatDeviceEntry row .1.3.6.1.4.1.2281.2.1.9.1

Entry containing general configuration information per device, both
local and remote sides.

Indexes

gnGenStatDeviceId

Column	Syntax	OID
gnGenStatDeviceIdmandatory This value indicates which device is involved in the specific row.	Enumeration Enumerated Values: 1 local 2 remote 3 drawer1 4 drawer2	.1.3.6.1.4.1.2281.2.1.9.1.1
gnGenStatDeviceCelsiusTempmandatory This is the temperature of the modem of the IDU in degrees of Celsius.	Integer32 Constraints: range: -10-70	.1.3.6.1.4.1.2281.2.1.9.1.2
gnGenStatDeviceFahrenheitTempmandatory This is the temperature of the modem of the IDU in degrees of Fahrenheit.	Integer32 Constraints: range: 14-158	.1.3.6.1.4.1.2281.2.1.9.1.3
gnGenStatDevicePowerSupplymandatory This octet represents the status of the power supplies of the IDU: bit 1 on = 3.3V faulty bit 2 on = -5V faulty bit 3 on = 5V faulty. bit 4 on = +8V faulty	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.1.9.1.4
gnGenStatDeviceCablemandatory Status of the cable to the ODU.	Enumeration Enumerated Values: 2 ok 3 short 4 open	.1.3.6.1.4.1.2281.2.1.9.1.5
gnGenStatDeviceDryContactmandatory The status of the dry contacts, Each input status is represented by a bit. When the input is on, the bit value is 0.When the input is off, the bit value is 1. The MSB represents external alarm 8. For example when only e…	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.2281.2.1.9.1.6
gnGenStatDeviceLedsmandatory The status of the IDU front panel LEDs. For the management station use.	OctetString Constraints: range: 3-3	.1.3.6.1.4.1.2281.2.1.9.1.7
gnGenStatInternalCommunicationmandatory The status of internal communication problem bit 1 = 1: between main CPU and ODU CPU. bit 2 = 1: between main CPU and MUX CPU. bit 3 = 1: between master main CPU and slave main CPU.	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.1.9.1.8
gnGenStatDeviceFanStatusmandatory The status of the IDU fans 1-2 or 1-4. bit 1 = IDU Fan1 is faulty. bit 2 = IDU Fan2 is faulty. bit 3 = IDU Fan2 is faulty. bit 4 = IDU Fan2 is faulty.	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.1.9.1.9
gnGenStatDeviceODUStatusmandatory ODU status reported with this parameter. Bit1 is MSB. The bit is set when a fault occurs. The bit is cleared when the fault clears. bit 1 = Power Supply status bit 2 = Synthesizer lock status bit 3 = Tx level status bit…	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.2281.2.1.9.1.10
gnGenStatDeviceIDUStatusmandatory IDU status reported with this parameter. Bit1 is MSB. The bit is set when a fault occurs. The bit is cleared when the fault clears. bit 1 = Power status bit 2 = Cable open status bit 3 = Cable short s…	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.2281.2.1.9.1.11
gnGenStatDeviceRSTStatusmandatory The bit is set when a fault occurs. The bit is cleared when the fault clears. bit 1 = Line loss of frame status bit 2 = Radio loss of frame status bit 3 = Line EXC status bit 4 = Radio EXC status bit 5 =…	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.2281.2.1.9.1.12

This table indicates drawer x.

gnGenDrawerXEntry row .1.3.6.1.4.1.2281.2.1.27.1

Entry containing drawer x namd and id.

Indexes

gnGenDrawerXId

Column	Syntax	OID
gnGenDrawerXIdmandatory This value indicates the drawer's id	Enumeration Enumerated Values: 3 drawer1 4 drawer2	.1.3.6.1.4.1.2281.2.1.27.1.1
gnGenDrawerXNamemandatory This value indicates the drawer's name	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.2281.2.1.27.1.2
gnGenDrawerXSlot1Statusmandatory notExist - board not exist. powerOff - board inserted and power off. powerOn - board inserted and power on. dbReady - board is power on and DB ready.	Enumeration Enumerated Values: 2 notExist 3 powerOff 4 powerOn 5 dbReady	.1.3.6.1.4.1.2281.2.1.27.1.3
gnGenDrawerXSlot2Statusmandatory notExist - board not exist. powerOff - board inserted and power off. powerOn - board inserted and power on. dbReady - board is power on and DB ready.	Enumeration Enumerated Values: 2 notExist 3 powerOff 4 powerOn 5 dbReady	.1.3.6.1.4.1.2281.2.1.27.1.4
gnGenDrawerXDeviceLedsmandatory The status of the IDU front panel LEDs. For the management station use.	OctetString Constraints: range: 3-3	.1.3.6.1.4.1.2281.2.1.27.1.5
gnGenDrawerXInternalCommunicationmandatory The status of internal communication problem bit 1 = 1: between main CPU and ODU CPU. bit 2 = 1: between main CPU and MUX CPU. bit 3 = 1: between master main CPU and slave main CPU.	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.1.27.1.6
gnGenDrawerXDeviceIDUStatusmandatory IDU status reported with this parameter. Bit1 is MSB. The bit is set when a fault occurs. The bit is cleared when the fault clears. bit 1 = Power status bit 2 = Cable open status bit 3 = Cable short st…	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.2281.2.1.27.1.7

This table indicates the cluster's IP Addresses.

addressesEntry row .1.3.6.1.4.1.2281.2.1.28.2.1

Entry containing the cluster's IP Addresses.

Indexes

addressesPeerIPId

Column	Syntax	OID
addressesPeerIPIdmandatory This value indicates the peer IP id	Integer32 Constraints: range: 1-9	.1.3.6.1.4.1.2281.2.1.28.2.1.1
addressesPeerIPAddressmandatory This value indicates the IP address of a Server/Client.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.2281.2.1.28.2.1.2

This table indicates the cluster's IP Addresses.

backplaneSlotMappingEntry row .1.3.6.1.4.1.2281.2.1.28.4.1

Entry containing the cluster's IP Addresses.

Indexes

backplaneSlotMappingSubrackId backplaneSlotMappingFloorId backplaneSlotMappingDrawerId backplaneSlotMappingSubDrawerId

Column	Syntax	OID
backplaneSlotMappingSubrackIdmandatory This value indicates the subrack index.	Integer32 Constraints: range: 1-3	.1.3.6.1.4.1.2281.2.1.28.4.1.1
backplaneSlotMappingFloorIdmandatory This value indicates the floor id The 4U floor index (upper) will be 99.	Integer32 Constraints: range: 1-100	.1.3.6.1.4.1.2281.2.1.28.4.1.2
backplaneSlotMappingDrawerIdmandatory For floors 1-3: IDC=1, Drawer 1=2, Drwaer2 =3. For 4U floor (floor #99), Aux=1, Power=2.	Integer32 Constraints: range: 1-3	.1.3.6.1.4.1.2281.2.1.28.4.1.3
backplaneSlotMappingSubDrawerIdmandatory This value indicates the sub drawer id IDC, Drawer 1 & 2 will be only 1. XC main (up) will be 1 and XC backup (lower) will be 2.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.2281.2.1.28.4.1.4
backplaneSlotMappingUnitTypemandatory The values are the same as in gnAgnCurrentAlarm Unit.	Enumeration Enumerated Values: 2 idc 3 odu 4 mux 5 modem 6 drawer 7 unknown 8 none 9 xc 10 auxInterface 11 power	.1.3.6.1.4.1.2281.2.1.28.4.1.5
backplaneSlotMappingUnitNumbermandatory This value indicates the unit number.	Integer32 Constraints: range: 1-15	.1.3.6.1.4.1.2281.2.1.28.4.1.6
backplaneSlotMappingUnitIndexmandatory This value indicates the unit number.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.1.28.4.1.7

This table indicates the Power Input.

powerInputEntry row .1.3.6.1.4.1.2281.2.1.29.1.1

Entry containing the Power Input.

Indexes

powerInputId

Column	Syntax	OID
powerInputIdmandatory This value indicates the power input Id.	Integer32 Constraints: range: 1-6	.1.3.6.1.4.1.2281.2.1.29.1.1.1
powerInputAdminmandatory This value indicates whether the power input Admin is enables or disabled.	Enumerationr/w Enumerated Values: 2 enable 3 disable	.1.3.6.1.4.1.2281.2.1.29.1.1.2
powerInputStatusmandatory This value indicates whether the power input is up or down, Notexist when power input card not exist. unknown when no A-Aux.	Enumeration Enumerated Values: 2 notexist 3 unknown 4 down 5 up	.1.3.6.1.4.1.2281.2.1.29.1.1.3
powerInputLedStatusmandatory This value, Led1 is MSB 2 bits. Each two bits represents one led:00 - Gray,01 - Blue.	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.1.29.1.1.4

This table indicates the XC Drawer.

xcDrawerEntry row .1.3.6.1.4.1.2281.2.1.29.3.1

Entry containing the XC Drawer.

Indexes

xcDrawerXCId

Column	Syntax	OID
xcDrawerXCIdmandatory This value, 1-2 for 1st rack, 3-4 for 2nd, 5-6 for 3rdy.	Integer32 Constraints: range: 1-6	.1.3.6.1.4.1.2281.2.1.29.3.1.1
xcDrawerLedsStatusmandatory This value, Led1 is MSB 2 bits, Led4 is LSB . Each two bits represents one led:00 - Gray,01 - Green, 10 - Orange, 11 - Red.	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.1.29.3.1.2
xcDrawerBoardHWVersionmandatory This value indicates the EEPROM value.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.1.29.3.1.3
xcDrawerBoardFWVersionmandatory This value indicates the Register value .	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.2281.2.1.29.3.1.4
xcDrawerBoardPostResetFWVersionmandatory This value indicates the Register value .	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.2281.2.1.29.3.1.5
xcDrawerSerialNumbermandatory This value indicates the EEPROM value.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.2281.2.1.29.3.1.6
xcDrawerResetXCBoardmandatory This value indicates whether to reset XC.	Enumerationr/w Enumerated Values: 2 noaction 3 reset	.1.3.6.1.4.1.2281.2.1.29.3.1.7
xcDrawerXCSelfTestResultmandatory This value indicates the XC self test result.	Enumeration Enumerated Values: 2 passed 3 failed	.1.3.6.1.4.1.2281.2.1.29.3.1.8
xcDrawerXCActivityRolemandatory This value indicates the XC activity role.	Enumeration Enumerated Values: 2 active 3 standby	.1.3.6.1.4.1.2281.2.1.29.3.1.9
xcDrawerSyncIdcDataBasemandatory .	Enumerationr/w Enumerated Values: 2 noOperation 3 idcToXC 4 xcToIdc	.1.3.6.1.4.1.2281.2.1.29.3.1.10
xcDrawerXCConnectormandatory This value indicates the XC activity role.	Enumeration Enumerated Values: 2 oneStm1XC	.1.3.6.1.4.1.2281.2.1.29.3.1.11

This table indicates carrier x.

gnGenCarrierXEntry row .1.3.6.1.4.1.2281.2.1.30.1

Entry of carrier x.

Indexes

gnGenCarrierXId

Column	Syntax	OID
gnGenCarrierXIdmandatory This value indicates the carrier id	Enumeration Enumerated Values: 3 carrier1 4 carrier2	.1.3.6.1.4.1.2281.2.1.30.1.1
gnGenCarrierXResetPerfMonmandatory Reset performance monitoring.	Enumerationr/w Enumerated Values: 2 reset 3 noAction	.1.3.6.1.4.1.2281.2.1.30.1.2
gnGenCarrierXSyncIdcDataBasemandatory idcToDrawer - copy configuration from the IDC disk to the HW (this operation istraffic effected). drawerToIdc - copy configuration from HW to IDC disk. this operation used to clear User Configuration Mismatch alarm. idc…	Enumerationr/w Enumerated Values: 2 noOperation 3 idcToDrawer 4 drawerToIdc 5 idcToAllDrawers	.1.3.6.1.4.1.2281.2.1.30.1.3

This table indicates the managers list that will receive traps.

gnAgnMgrEntry row .1.3.6.1.4.1.2281.2.2.1.1

Entry containing the managers IP addresses and the trap filter options.

Indexes

gnAgnMgrId

Column	Syntax	OID
gnAgnMgrIdmandatory This value indicates an index of a specific manager	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.1.1.1
gnAgnMgrIPmandatory This value indicates the managers IP address. WRITE an IP address of all zeroes (0.0.0.0) will remove the entry.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2281.2.2.1.1.2
gnAgnMgrAlarmGroupMaskmandatory bit mask .1 is 'send a trap' 0 is 'dont send a trap'. The list of alarms from MSB to LSB is: bit 1 = Power Supply Alarm bit 2 = Cable Alarm bit 3 = Temperature Alarm bit 4 = External Alarm …	OctetStringr/w Constraints: range: 2-2	.1.3.6.1.4.1.2281.2.2.1.1.3
gnAgnMgrSeverityFiltermandatory This is a bit mask value for masking traps according to its severity. There is a bit for each severity. If the relevant bit is on (1), then the Agent will send traps with this severity, and it won't send if the bit …	OctetStringr/w Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.2.1.1.4
gnAgnMgrTrapPortmandatory The Port for sending the trap for each manager (possible values: 70-65535)	Integer32r/w Constraints: range: 70-65535	.1.3.6.1.4.1.2281.2.2.1.1.5

This table is the agents alarm and event log file.

gnAgnLogFileEntry row .1.3.6.1.4.1.2281.2.2.2.4.1

Entry containing the agents alarm and event log file.

Indexes

gnAgnLogFileId

Column	Syntax	OID
gnAgnLogFileIdmandatory This value indicates the index of an alarm logfile entry. Entry 1 is the most recent logfile event	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.1
gnAgnLogFileValidmandatory This value indicates the validity of the indexed alarm logfile entry. a VALID log entry is (2) and an INVALID entry is (3).	Enumeration Enumerated Values: 2 valid 3 notvalid	.1.3.6.1.4.1.2281.2.2.2.4.1.2
gnAgnLogFileDatemandatory This field is the date the alarm occurred, formatted as YYYY-MM-DD. YYYY represents the year, MM the month and DD -the day.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2281.2.2.2.4.1.3
gnAgnLogFileTimemandatory This field is the hour the alarm occurred - format HH:MM. HH - Hour, MM - minute	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2281.2.2.2.4.1.4
gnAgnLogFileSeveritymandatory This value indicates the severity of the alarm, 31 for CRITICAL, 15 for MAJOR, 7 for MINOR, 3 for WARNING and 1 for EVENT.	Enumeration Enumerated Values: 1 event 3 warning 7 minor 15 major 31 critical	.1.3.6.1.4.1.2281.2.2.2.4.1.5
gnAgnLogFileTextmandatory This field describes the alarm that occurred. Max length 40 characters.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2281.2.2.2.4.1.6
gnAgnLogFileDeviceCelsiusTempmandatory This is the temperature of the IDU in degrees Celsius, during the alarm acceptance.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.7
gnAgnLogFileDevicePowerSupplymandatory This is the Power supply status of the IDU, during the alarm acceptance bit 1 on = 3.3V faulty bit 2 on = -5V faulty bit 3 on = 5V faulty. bit 4 on = +8V faulty	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.2.2.4.1.8
gnAgnLogFileInternalCommunicationmandatory This is the internal communication status of the IDU, during the alarm acceptance bit 1 = 1: between main CPU and ODU CPU. bit 2 = 1: between main CPU and MUX CPU. bit 3 = 1: between master main CPU and slave main CPU.	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.2.2.4.1.9
gnAgnLogFileDeviceFanStatusmandatory This is the Fan status of the IDU, during the alarm acceptance bit 1 = Fan1 is faulty. bit 2 = Fan 2 is faulty.	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.2.2.4.1.10
gnAgnLogFileDeviceODUStatusmandatory This is the ODU status during the alarm acceptance bit 1 MSB bit 1 = Power Supply status bit 2 = Synthesizer lock status bit 3 = Tx level status bit 4 = ATPC status bit 5 = Rx level status bit 6 = Not currently used bit…	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.2281.2.2.2.4.1.11
gnAgnLogFileDeviceIDUStatusmandatory This is the IDU status during the alarm acceptance bit 1 MSB bit 1 = Power status - bit 2 = Cable open status - bit 3 = Cable short status - bit 4 = Modem Lock status bit 5 = Temperature status bit 6 = Not current…	OctetString Constraints: range: 3-3	.1.3.6.1.4.1.2281.2.2.2.4.1.12
gnAgnLogFileOduCelsiusTempmandatory This is the temperature of the ODU in degrees Celsius, during the alarm acceptance.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.13
gnAgnLogFileOduReceiveLevelmandatory This is the received signal level in DBM, during the alarm acceptance	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.14
gnAgnLogFileOduSynthesizerVCOLockmandatory This is the Synthesizer status, during the alarm acceptance bit 1 on = TX IF synthesizer fault bit 2 on = RX IF synthesizer fault bit 3 on = Xband synthesizer fault bit 4 on = History TX IF synthesizer fault bit 5 on = …	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.2.2.4.1.15
gnAgnLogFileOduPowerSupplymandatory This is the ODU power supply status, during the alarm acceptance bit 1 on = +5V faulty bit 2 on = +8V faulty bit 3 on = +12V faulty bit 4 on = -12V faulty.	OctetString Constraints: range: 1-1	.1.3.6.1.4.1.2281.2.2.2.4.1.16
gnAgnLogFileLineBERCurmandatory This is the Line BER (Bit Error Rate), during the alarm acceptance. Included for future development, not currently supported.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.17
gnAgnLogFileRadioBERCurmandatory This is the Radio BER (Bit Error Rate), during the alarm acceptance. Included for future development, not currently supported.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.18
gnAgnLogFileModStatusmandatory This is the Modulator status, during the alarm acceptance ok(2), modulatorFault(3)	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.19
gnAgnLogFileDemodStatusmandatory This is the Demodulator status, during the alarm acceptance . This field is for internal use internal debugging	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.20
gnAgnLogFileLastDemodDefectBlocksmandatory This is the number of the Defected blocks (blocks that couldn't be corrected) by the FEC, during the alarm acceptance last second.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.21
gnAgnLogFileLastDemodBytesCorrectedmandatory This is the number of the bytes that were corrected by the FEC, during the alarm acceptance last second.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.22
gnAgnLogFileLastDemodBlocksCorrectedmandatory This is the number of the blocks that were corrected by the FEC , during the alarm acceptance last second.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.23
gnAgnLogFileUniqueIdmandatory Unique Id for each log from 1 to 2,147,483,647 ( = 0x7FFFFFFF).	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.24
gnAgnLogFileSourcemandatory The soure drawer of the alarm.	Enumeration Enumerated Values: 1 interfaces 2 idc 3 drawer1 4 drawer2 257 tIdc1 258 tIdc2 259 tIdc3 260 tIdc4 261 tIdc5 262 tIdc6 263 tIdc7 264 tIdc8 265 tIdc9 513 tDrawer1 514 tDrawer2 515 tDrawer3 516 tDrawer4 517 tDrawer5 518 tDrawer6 519 tDrawer7 520 tDrawer8 521 tDrawer9 522 tDrawer10 523 tDrawer11 524 tDrawer12 525 tDrawer13 526 tDrawer14 527 tDrawer15 769 tXC1 770 tXC2 771 tXC3 772 tXC4 773 tXC5 774 tXC6	.1.3.6.1.4.1.2281.2.2.2.4.1.25
gnAgnLogFileTimeTmandatory The time of the alarm represented by the number of seconds from 1.1.1970.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.2.4.1.26

This table is the input external alarm table.

gnAgnInExternAlarmEntry row .1.3.6.1.4.1.2281.2.2.3.1.1

Entry containing the external alarm inputs.

Indexes

gnAgnInExternAlarmDevId gnAgnInExternAlarmIndex

Column	Syntax	OID
gnAgnInExternAlarmDevIdmandatory This value indicates device to which the external alarm is connected - 1 Local, 2 Remote	Enumeration Enumerated Values: 1 local 2 remote	.1.3.6.1.4.1.2281.2.2.3.1.1.1
gnAgnInExternAlarmIndexmandatory This value indicates the index of the input external alarm 1 to 8	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.2281.2.2.3.1.1.2
gnAgnInExternAlarmEnablemandatory This value indicates if this Input alarm is enabled.	Enumerationr/w Enumerated Values: 2 disabled 3 enabled	.1.3.6.1.4.1.2281.2.2.3.1.1.3
gnAgnInExternAlarmTextmandatory This field describes the external alarm. Max string 20 characters	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.2281.2.2.3.1.1.4
gnAgnInExternAlarmSeveritymandatory This value indicates the severity of the external alarm 31 CRITICAL ,15 MAJOR, 7 MINOR, 3 WARNING and 1 EVENT.	Enumerationr/w Enumerated Values: 1 event 3 warning 7 minor 15 major 31 critical	.1.3.6.1.4.1.2281.2.2.3.1.1.5

This table is the output relay alarm table.

gnAgnOutRelayAlarmEntry row .1.3.6.1.4.1.2281.2.2.3.2.1

Entry containing the output relay alarms.

Indexes

gnAgnOutRelayAlarmDevId gnAgnOutRelayAlarmIndex

Column	Syntax	OID
gnAgnOutRelayAlarmDevIdmandatory This value indicates device from which the relay is sent from - 1 Local, 2 Remote	Enumeration Enumerated Values: 1 local 2 remote	.1.3.6.1.4.1.2281.2.2.3.2.1.1
gnAgnOutRelayAlarmIndexmandatory This value indicates the index of the Output Relay alarm 1 to 5	Integer32 Constraints: range: 1-5	.1.3.6.1.4.1.2281.2.2.3.2.1.2
gnAgnOutRelayAlarmTypemandatory This value indicates the alarm/led that causes the relay to change its state	Enumerationr/w Enumerated Values: 2 major 3 minor 4 warning 5 external 6 power 7 ber 8 line 9 loopback 10 lof 11 idu 12 odu 13 cable 14 remote 15 critical 16 testOn 17 off 18 xc	.1.3.6.1.4.1.2281.2.2.3.2.1.3

This table controls the Internal Download process
from manager to MUX and ODU (local and remote).

gnAgnInternalDownloadEntry row .1.3.6.1.4.1.2281.2.2.5.1

Entry containing the internal download process controls, for local and
remote.

Indexes

gnAgnInternalDownloadId

Column	Syntax	OID
gnAgnInternalDownloadIdmandatory This value indicates an index of a specific Internal Download operation.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.5.1.1
gnAgnInternalDownloadOperationmandatory The Operation Description	Enumeration Enumerated Values: 2 localMUX 3 localODU 4 remoteMUX 5 remoteODU 6 leftShelfODU 7 rightShelfODU	.1.3.6.1.4.1.2281.2.2.5.1.2
gnAgnInternalDownloadActionmandatory This parameter controls the download action operation.	Enumerationr/w Enumerated Values: 2 start 3 cancel 4 clear 5 noAction 6 upLoadFpga	.1.3.6.1.4.1.2281.2.2.5.1.3
gnAgnInternalDownloadStatusmandatory Internal download session status	Enumeration Enumerated Values: 1 gnInternalDownloadSessionError 2 gnInternalDownloadSessionClearing 3 gnInternalDownloadSessionSendBlock 4 gnInternalDownloadSessiontimeout 5 gnInternalDownloadSessionDone 6 gnInternalDownloadSessionWaitForRetransmit 255 gnNoInternalDownloadSession	.1.3.6.1.4.1.2281.2.2.5.1.4
gnAgnInternalDownloadBlockCountmandatory The total number of blocks sent in the current session.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.5.1.5
gnAgnInternalDownloadVersionControlmandatory Points to the software version to be uploaded	Enumerationr/w Enumerated Values: 1 version1 2 version2	.1.3.6.1.4.1.2281.2.2.5.1.6
gnAgnInternalDownloadFileSizeInBytesmandatory The total number of blocks in the current file	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.5.1.7
gnAgnInternalDownloadBytesCountmandatory The number of bytes sent in the current session	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.5.1.8

This table controls the Inter Link Download process
between local and remote masters and between master and slave (local or
remote).
      Each session transfers MUX, ODU or manager (IDC) software.

gnAgnInterLinkEntry row .1.3.6.1.4.1.2281.2.2.6.1

Entry containing the process controls for the interlink download
process, for local and remote.

Indexes

gnAgnInterLinkId

Column	Syntax	OID
gnAgnInterLinkIdmandatory This value indicates the index of a specific InterLink operation.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.6.1.1
gnAgnInterLinkSidemandatory The Link Side	Enumeration Enumerated Values: 2 local 3 remote	.1.3.6.1.4.1.2281.2.2.6.1.2
gnAgnInterLinkSourcemandatory The source distribution center.	Enumerationr/w Enumerated Values: 2 me 3 mate	.1.3.6.1.4.1.2281.2.2.6.1.3
gnAgnInterLinkDestinationmandatory The destination distribution center. The destination may be selected as the local IDU being contacted (me), the collocated local IDU, in a protected configuration (mate) or it may be selected to be the remote IDU.	Enumerationr/w Enumerated Values: 2 me 3 mate 4 remote	.1.3.6.1.4.1.2281.2.2.6.1.4
gnAgnInterLinkSoftwaremandatory The software type to be transferred. MUX, ODU or IDU (referred to as manager).	Enumerationr/w Enumerated Values: 2 manager 3 mux 4 odu	.1.3.6.1.4.1.2281.2.2.6.1.5
gnAgnInterLinkActionmandatory This parameter controls the interlink action operation.	Enumerationr/w Enumerated Values: 2 start 3 cancel 4 noAction	.1.3.6.1.4.1.2281.2.2.6.1.6
gnAgnInterLinkStatusmandatory Inter-link session status	Enumeration Enumerated Values: 1 gnInterLinkSessionError 2 gnInterLinkSessionClearing 3 gnInterLinkSessionSendBlock 4 gnInterLinkSessiontimeout 5 gnInterLinkSessionDone 255 gnNoInterLinkSession	.1.3.6.1.4.1.2281.2.2.6.1.7
gnAgnInterLinkBlockCountmandatory The total number of blocks sent in the current session.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.6.1.8

This table contains the IDU, MUX, ODU & WS software versions;
local and remote.

gnSoftwareVersionEntry row .1.3.6.1.4.1.2281.2.2.7.1

Entry containing the currently operating IDU, ODU and MUX software
versions.

Indexes

gnSoftwareVersionId

Column	Syntax	OID
gnSoftwareVersionIdmandatory The ID indicates which device is involved in the specific row. The software table includes two rows, one for the local radio and one for the remote radio.	Enumeration Enumerated Values: 1 local 2 remote	.1.3.6.1.4.1.2281.2.2.7.1.1
gnSoftwareVersionIDUmandatory This is the IDU software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.2
gnSoftwareVersionMUXmandatory This is the MUX software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.3
gnSoftwareVersionODUmandatory This is the ODU software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.4
gnSoftwareVersionIDUPostResetVersionmandatory This is the IDU post reset software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.5
gnSoftwareVersionMUXPostResetVersionmandatory This is the MUX post reset software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.6
gnSoftwareVersionODUPostResetVersionmandatory This is the ODU post reset software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.7
gnSoftwareVersionMuxAlteraVermandatory This string contains the MUX altera versions	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.8
gnSoftwareIDCVersionControlmandatory Points to the software version that will run on the next reset	Enumerationr/w Enumerated Values: 1 version1 2 version2	.1.3.6.1.4.1.2281.2.2.7.1.9
gnSoftwareVersionWSAlteraVermandatory This is the WS software version	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.10
gnSoftwareVersionWSPostResetVersionmandatory This is the WS post reset software version	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.11
gnSoftwareVersionMrmcVermandatory This is the MRMC filter table software version	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.12
gnSoftwareVersionMrmcPostResetVermandatory This is the MRMC filter table post reset software version	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.13
gnSoftwareVersionBootSoftVermandatory This is the BOOT software version	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.14
gnSoftwareVersionBootFlashVermandatory This is the BOOT FLASH version	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.15
gnSoftwareVersionAcmLutVermandatory This is the ACM LUT software version	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.16
gnSoftwareVersionAcmLutVerPostResetVermandatory This is the ACM LUT post reset software version	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.7.1.17
gnSoftwareVersionSfdVermandatory This is the SFD software version	OctetString Constraints: range: 0-31	.1.3.6.1.4.1.2281.2.2.7.1.18

This table defines the inband channels mapping.

gnAgnInBandMngXChannelEntry row .1.3.6.1.4.1.2281.2.2.9.17.1

This is an entry in the inband channel table.
This table contains a row for every channel (1..4).
First 3 physical channels are available in the 8 possible mapping options (on both carrier drawers).
An additional channe…

Indexes

gnAgnInBandMngXChannelId

Column	Syntax	OID
gnAgnInBandMngXChannelIdmandatory The channel Id	Enumeration Enumerated Values: 1 channel1 2 channel2 3 channel3 4 channel4	.1.3.6.1.4.1.2281.2.2.9.17.1.1
gnAgnInBandMngXChannelIfIndexmandatory The ifIndex of the interface that is mapped to this channel	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.9.17.1.2
gnAgnInBandMngXChannelTypemandatory The type of channel the in-band-management goes over. Default value for channels 1 and 3 in the carrier drawers is Proprietary. Channel 2 not allowed to be Proprietary. In protection the ch_type of ch#3 can not …	Enumerationr/w Enumerated Values: 2 proprietary 3 dccr 4 dccm 5 mediaspecific 6 pppoe	.1.3.6.1.4.1.2281.2.2.9.17.1.3
gnAgnInBandMngXChannelStatemandatory Enable/Disable the in band channel	Enumerationr/w Enumerated Values: 2 enable 3 disable	.1.3.6.1.4.1.2281.2.2.9.17.1.4
gnAgnInBandMngXChannelNeighborIPmandatory The PPP IP address of the gateway network element.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2281.2.2.9.17.1.5
gnAgnInBandMngXChannelStatusmandatory This MIB parameter defines the In-band PPP connection status. If the MIB value is up the PPP connection is up and running If the MIB value is down the PPP connection is down and is in initialization state. (Trying t…	Enumeration Enumerated Values: 2 up 3 down 4 closed	.1.3.6.1.4.1.2281.2.2.9.17.1.6

This table defines the IP addresses of the units that are connected Inband.

gnNeighborInBandEntry row .1.3.6.1.4.1.2281.2.2.10.1.1

This is an entry in the IP addresses of the units that are connected Inband.
This table contains a row for every interface which type is logically connected.
for example regenerator which is connected in band has two ne…

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
gnNeighborInBandIPmandatory The PPP IP address of the gateway network element.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2281.2.2.10.1.1.1
gnNeighborInBandStatusmandatory This MIB parameter defines the In-band PPP connection status. If the MIB value is up the PPP connection is up and running If the MIB value is down the PPP connection is down and is in initialization state. (Trying t…	Enumeration Enumerated Values: 2 up 3 down 4 closed	.1.3.6.1.4.1.2281.2.2.10.1.1.2

This table defines the IP addresses of the units that are connected Inband.

gnNeighborInBandXEntry row .1.3.6.1.4.1.2281.2.2.10.4.1

This is an entry in the IP addresses of the units that are connected Inband.
This table contains a row for every interface which type is logically connected.
for example regenerator which is connected in band has two ne…

Indexes

gnNeighborInBandXId

Column	Syntax	OID
gnNeighborInBandXIdmandatory	Enumeration Enumerated Values: 3 drawer1 4 drawer2	.1.3.6.1.4.1.2281.2.2.10.4.1.1
gnNeighborInBandXIPmandatory The PPP IP address of the gateway network element.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2281.2.2.10.4.1.2

This table shows the Neighbor IP for each STM connection.

gnNeighborIpEntry row .1.3.6.1.4.1.2281.2.2.10.5.1

.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
gnNeighborIpDetectModemandatory The Neighbor detect can be done automatically or to be manually insreted. Disable marks that the IP Detect is not used.	Enumerationr/w Enumerated Values: 2 disable 3 manual 4 auto	.1.3.6.1.4.1.2281.2.2.10.5.1.1
gnNeighborIpAddressmandatory The neighbor IP address.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.2281.2.2.10.5.1.2
gnNeighborIpRemoteIfIndexmandatory The If index of the neighbor IP address connected to the current If Index.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.10.5.1.3
gnNeighborIpRemoteTypemandatory The Type of the neighbor.	Enumerationr/w Enumerated Values: 1 regenerator 2 access 3 adm 4 unit1500p 5 admline2line	.1.3.6.1.4.1.2281.2.2.10.5.1.4

This table contains the IDU, MUX & ODU software versions;
local and remote.

gnSoftwareDrawerVersionEntry row .1.3.6.1.4.1.2281.2.2.13.1

Entry containing the currently operating IDU, ODU and MUX software
versions.

Indexes

gnSoftwareDrawerId

Column	Syntax	OID
gnSoftwareDrawerIdmandatory The ID indicates which Drawer is involved in the specific row.	Enumeration Enumerated Values: 3 drawer1 4 drawer2	.1.3.6.1.4.1.2281.2.2.13.1.1
gnSoftwareDrawerVersionMUXmandatory This is the MUX software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.13.1.2
gnSoftwareDrawerVersionMUXPostResetVersionmandatory This is the ODU software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.13.1.3
gnSoftwareDrawerVersionODUmandatory This is the MUX post reset software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.13.1.4
gnSoftwareDrawerVersionODUPostResetVersionmandatory This is the MUX post reset software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.13.1.5
gnSoftwareDrawerVersionModemFilemandatory This is the Modem software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.13.1.6
gnSoftwareDrawerVersionModemFilePostResetVersionmandatory This is the Modem post reset software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.13.1.7
gnSoftwareDrawerVersionModemScriptmandatory This is the Modem software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.13.1.8
gnSoftwareDrawerVersionModemScriptPostResetVersionmandatory This is the Modem post reset software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.13.1.9
gnSoftwareDrawerVersionRfuFpgaVersionmandatory This is the Rfu Fpga software version.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.2281.2.2.13.1.10

This table includes the currently open alarm (when a RAISED trap is
sent, an alarm is added to the table, when a CLEAR trap is sent,
the alarm is removed.

gnAgnCurrentAlarmEntry row .1.3.6.1.4.1.2281.2.2.14.2.1

Entry containing the info of a currently RAISED trap.

Indexes

gnAgnCurrentAlarmCounter

Column	Syntax	OID
gnAgnCurrentAlarmCountermandatory A running counter of open alarm, the counter is incremented on every new RAISED trap. It is cleared after reset. This counter is (optionaly) attached to each trap.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.14.2.1.1
gnAgnCurrentAlarmSeveritymandatory The current Alarm severity	Enumeration Enumerated Values: 1 event 3 warning 7 minor 15 major 31 critical	.1.3.6.1.4.1.2281.2.2.14.2.1.2
gnAgnCurrentAlarmIdmandatory Alarm Identifier (contains alarm type and interface). Same AlarmId for rasie and clear alarms.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.14.2.1.3
gnAgnCurrentAlarmIfIndexmandatory Interface Index where the alarm occurred, alarms that are not associated with specific interface will have the following value: For IDC related alarms the value is: 65001 For drawer1 related alarms th…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.14.2.1.4
gnAgnCurrentAlarmOriginmandatory The origin drawer of the alarm (if applicable, otherwise it will be idc(2)).	Enumeration Enumerated Values: 1 interfaces 2 idc 3 drawer1 4 drawer2 5 unKnown 257 tIdc1 258 tIdc2 259 tIdc3 260 tIdc4 261 tIdc5 262 tIdc6 263 tIdc7 264 tIdc8 265 tIdc9 513 tDrawer1 514 tDrawer2 515 tDrawer3 516 tDrawer4 517 tDrawer5 518 tDrawer6 519 tDrawer7 520 tDrawer8 521 tDrawer9 522 tDrawer10 523 tDrawer11 524 tDrawer12 525 tDrawer13 526 tDrawer14 527 tDrawer15 769 tXC1 770 tXC2 771 tXC3 772 tXC4 773 tXC5 774 tXC6	.1.3.6.1.4.1.2281.2.2.14.2.1.5
gnAgnCurrentAlarmUnitmandatory The unit of the alarm.	Enumeration Enumerated Values: 2 idc 3 odu 4 mux 5 modem 6 drawer 7 unKnown 9 xc	.1.3.6.1.4.1.2281.2.2.14.2.1.6
gnAgnCurrentAlarmTrapIDmandatory The ID of the RAISED trap that was sent when this alarm was raised.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.14.2.1.7
gnAgnCurrentAlarmTimeTmandatory Timestamp of this alarm, this number is the seconds from midnight 1.1.1970.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2281.2.2.14.2.1.8
gnAgnCurrentAlarmTextmandatory The alarm display text (same as the text in the sent trap).	RFC1213-MIBDisplayString	.1.3.6.1.4.1.2281.2.2.14.2.1.9