wtnRadioAmplifiersEnable
ZHONE-PHY-WTN-RADIO-MIB ·
.1.3.6.1.4.1.5504.5.8.1.1.8
Object
true(1) - Enables amplifiers for transmitter and receiver.
The radio will begin transmitting and receiving data. If the ODU
is looped back, unable to lock onto a signal, or the ODU equipment
has failed, the enable command will return an error trap and
the amplifier enable state will transition to disableAmplifiers(2).
false(2) - shuts down the transmit and receive amplifiers of the ODU.
This will cause the link to go down. Payload will be dropped.
When the amplifiers are turned off, the active and standby
channel assignments may be freely changed, if necessary,
but notification of such changes to the far end will not be done
automatically. That is, channel assignments made when the
amplifiers are disabled must be done manually at each node -
near end and far end.
Default value after power up is false(2).
Context
- MIB
- ZHONE-PHY-WTN-RADIO-MIB
- OID
.1.3.6.1.4.1.5504.5.8.1.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- wtnConfigEntry
- Table
- wtnConfigTable
- Siblings
- 17
Values & Constraints
Type Values
1 | true |
2 | false |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wtnRadioIfIndex This object should be made equal to the Ifindex used for
the radio interface. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.5504.5.8.1.1.1 |
| wtnRxBERHysteresisWindow After a wtnBerAlarm trap is sent, it is revoked using the same trap with
the condition flag set to false when the modem BER estimate is lower
than the set point wtnModemRxBERThre… | column | ZHONE-RADIO-TC-MIBSkyZhoneScientificNotation | .1.3.6.1.4.1.5504.5.8.1.1.10 |
| wtnAntennaSize Initial power of transmitter is based upon antenna diameter.
oneFoot(1) - a one foot dish
twoFeet(2) - a two foot dish
fourFeet(4) - a four foot dish
sixFeet(6) - a… | column | feet Enumeration | .1.3.6.1.4.1.5504.5.8.1.1.11 |
| wtnIduOduCableLength The length of the coaxial cable between the Indoor
Unit and the Outdoor Unit.
Used internally to compensate for the coaxial cable's
natural attenuation of the signa… | column | feet Integer32 | .1.3.6.1.4.1.5504.5.8.1.1.12 |
| wtnRssiThresh Set point of RSSI thresholdalarm. When the ODU RSSI estimate
is lower than this value, a wtnRssiDeviation trap will be emitted.
When the ODU RSSI estimate is higher than this set… | column | dB Integer32 | .1.3.6.1.4.1.5504.5.8.1.1.13 |
| wtnRssiHysteresisWindow After a wtnRssiDeviation Trap is sent, an the trap is re-emitted
with the condition flag set to false when the ODU RSSI
estimate is higher than the set point wtnOduRxRSSIThresh p… | column | dB SNMPv2-SMIInteger32 | .1.3.6.1.4.1.5504.5.8.1.1.14 |
| wtnTrapsEnable When true(1), radio traps may be emitted.
When false(2), radio traps will be absorbed.
Default value is true(1) = enabled. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.5504.5.8.1.1.15 |
| wtnOduLoopback loopbackOn(1) - engages the loopback function at the ODU (outdoor unit).
Data normally transmitted by the radio is instead returned to the IDU
(indoor unit). This is useful to ch… | column | Enumeration | .1.3.6.1.4.1.5504.5.8.1.1.16 |
| wtnOduIdentifier Textual description of ODU.
This string typically identifies the location of antenna. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.5504.5.8.1.1.17 |
| wtnTxLevel Desired transmitter signal strength (TSSI) at antenna.
Note: Accuracy decreases as power levels decrease below 20dBm.
FCC maximum power allowed is +30dBm. | column | dB Integer32 | .1.3.6.1.4.1.5504.5.8.1.1.18 |
| wtnActiveChannelNumber Assigns one of N allowed frequency pairs for the radio
transmitter and reciever as described in zhoneRadio-TC.mib.
5.7Ghz family (sysObjId) systems:
--------------… | column | ZHONE-RADIO-TC-MIBSkyZhoneRadioChannelNumber | .1.3.6.1.4.1.5504.5.8.1.1.2 |
| wtnActiveTransmitFrequency Current transmit frequency. As described in zhoneRadio-TC.mib.
23Ghz family: ( according to sysObjId )
------------------------------------------- … | column | Hz ZHONE-RADIO-TC-MIBSkyZhoneScientificNotation | .1.3.6.1.4.1.5504.5.8.1.1.3 |
| wtnStandbyChannelNumber Assigns one of N allowed standby frequency pairs to the radio
transmitter and reciever as described in zhoneRadio-TC.mib.
5.7Ghz family (sysObjId) systems:
-------… | column | ZHONE-RADIO-TC-MIBSkyZhoneRadioChannelNumber | .1.3.6.1.4.1.5504.5.8.1.1.4 |
| wtnStandbyTransmitFrequency Standby Transmit frequency as described in zhoneRadio-TC.mib.
23Ghz family: ( according to sysObjId )
------------------------------------------- … | column | Hz ZHONE-RADIO-TC-MIBSkyZhoneScientificNotation | .1.3.6.1.4.1.5504.5.8.1.1.5 |
| wtnAutoChannelSwitchEnable true(1) - allows radio to automatically switch
to the standby channel in case of active channel
interference.
false(2) - inhibits radio from automatically
switch… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.5504.5.8.1.1.6 |
| wtnChannelSeparation 23Ghz family (sysObjId) systems:
---------------------------------
Channel separation - the fixed difference between transmit
and receive frequency.
Only three val… | column | Enumeration | .1.3.6.1.4.1.5504.5.8.1.1.7 |
| wtnRxBERThresh Set point of BER alarm. When the modem BER estimate
is higher than this value, a modem BER alarm will occur.
The BER over threshold Causes trap wtnBerAlarm to be emitted.
The ala… | column | ZHONE-RADIO-TC-MIBSkyZhoneScientificNotation | .1.3.6.1.4.1.5504.5.8.1.1.9 |