tnOamPingCtlTestMode
TN-OAM-TEST-MIB ·
.1.3.6.1.4.1.7483.6.1.2.11.1.4.1.5
Object
column
r/w
Enumeration
Specifies the type of OAM ping test defined by this entry.
The configuration parameters unique to a specific test type are to
be found in an sparsely dependent table extension for that test type.
none - the test type is unspecified.
sdpPing - tests SDP connectivity and round trip time.
mtuPing - tests MTU path size.
svcPing - determines the existence and operative state of the
service ID on the far end ESR.
NOTE: This is a one-shot test.
macQuery - obsolete. Originally specified functionality is as follows.
- determines a specific address mapping for the service ID.
See tnOamMacPingCtlTable for additional parameters.
NOTE: This is a one-shot test.
macPing - determines address mappings for the service ID.
See tnOamMacPingCtlTable for additional parameters.
macPopulate - populates an OAM MAC address into the FIBs.
See tnOamMacPingCtlTable for additional parameters.
NOTE: This is a one-shot test.
macPurge - deletes an OAM MAC address from the FIBs.
See tnOamMacPingCtlTable for additional parameters.
NOTE: This is a one-shot test.
lspPing - tests LSP path connectivity and round trip time.
See tnOamLspPingCtlTable for additional parameters.
vprnPing - tests IP path connectivity and round trip time within
a specified VPRN service. See tnOamVprnPingCtlTable
for additional parameters.
atmPing - tests ATM path connectivity and round trip time on an
ATM VCC. See tnOamAtmPingCtlTable for additional
parameters.
mfibPing - tests IP multicast connectivity and round trip time
within a specified VPLS service.
See tnOamMfibPingCtlTable for additional parameters.
cpePing - determines IP connectivity to a CPE
within a specified VPLS service.
See tnOamCpePingCtlTable for additional parameters.
mrInfo - Get multicast router's capabilities and the list of
interfaces with neighbors.
vccvPing - tests pseudowire connectivity and round trip time.
See tnOamVccvPingCtlTable for additional parameters.
icmpPing - tests IP connectivity and round trip time.
See tnOamIcmpPingCtlTable for additional parameters.
dnsPing - tests DNS name resolution connectivity and round trip time.
ancpLoopback - send an OAM loopback test request to the access node.
See tnOamAncpTestCtlTable for additional parameters.
p2mpLspPing - tests P2MP LSP path connectivity and round trip time.
Test mode cannot be p2mpLspPing if SAA is enabled. See
tnOamP2mpLspPingCtlTable for additional parameters.
ethCfmLoopback - performs Ethernet Connectivity Fault Management (CFM)
loopback tests. This MIB supports the SAA form of this
test only (the OAM form uses a separate set of objects - see
IEEE8021-CFM-MIB). Additional parameters for the SAA
ethCfmLoopback test are in tnOamEthCfmPingCtlTable.
ethCfmTwoWayDelay - performs Ethernet Connectivity Fault Management
(CFM) two way delay tests. This MIB supports the SAA form
of this test only (the OAM form uses a separate set of
objects - see IEEE8021-CFM-MIB). Additional parameters for
the SAA ethCfmTwoWayDelay test are in
tnOamEthCfmPingCtlTable.
ethCfmOneWayDelay - performs Ethernet Connectivity Fault Management
(CFM) one way delay tests. This MIB supports the SAA form
of this test only (the OAM form uses a separate set of
objects - see IEEE8021-CFM-MIB). Additional parameters for
the SAA ethCfmOneWayDelay test are in
tnOamEthCfmPingCtlTable.
mobGtpPing - Tests GTP (GPRS Tunnelling Protocol) path connectivity.
ethCfmTwoWaySlm - performs Ethernet Connectivity Fault Management
(CFM) two way Synthetic Loss Measurement (SLM) tests. This
MIB supports the SAA form of this test only (the OAM form
uses a separate set of objects - see
TN-IEEE8021-CFM-MIB). Additional parameters for the SAA
ethCfmTwoWaySlm test are in tnOamEthCfmPingCtlTable.
ethCfmTwoWayLm - performs Ethernet Connectivity Fault Management
(CFM) two way Loss Measurement (LM) tests. This
MIB supports the SAA form of this test only (the OAM form
uses a separate set of objects - see
TN-IEEE8021-CFM-MIB). Additional parameters for the SAA
ethCfmTwoWayLm test are in tnOamEthCfmPingCtlTable.
Context
- MIB
- TN-OAM-TEST-MIB
- OID
.1.3.6.1.4.1.7483.6.1.2.11.1.4.1.5- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- tnOamPingCtlEntry
- Table
- tnOamPingCtlTable
- Siblings
- 37
Syntax
Enumeration
Values & Constraints
Enumerated Values
0 | none |
1 | sdpPing |
2 | mtuPing |
3 | svcPing |
5 | macPing |
6 | macPopulate |
7 | macPurge |
8 | lspPing |
9 | vprnPing |
10 | atmPing |
11 | mfibPing |
12 | cpePing |
13 | mrInfo |
14 | vccvPing |
15 | icmpPing |
16 | dnsPing |
17 | ancpLoopback |
18 | p2mpLspPing |
19 | ethCfmLoopback |
20 | ethCfmTwoWayDelay |
21 | mobGtpPing |
22 | ethCfmTwoWaySlm |
23 | ethCfmTwoWayLm |
24 | ethCfmOneWayDelay |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| tnOamPingCtlTestIndex The test name index of the Nokia SROS OAM ping test.
This is locally unique, within the scope of an
tnOamPingCtlOwnerIndex. | column | OctetString | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.1 |
| tnOamPingCtlProfile The value of tnOamPingCtlProfile specifies the profile to be used
with the forwarding class specified in tnOamPingCtlFcName. This
object is optional.
As shown in t… | column | TN-TC-MIBTProfile | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.10 |
| tnOamPingCtlMtuStartSize The value of tnOamPingCtlMtuStartSize specifies the size of the first
OAM Echo message sent as part of an 'mtuPing' test.
Setting this object to a non-zero value is… | column | Octets Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.11 |
| tnOamPingCtlMtuEndSize The value of tnOamPingCtlMtuEndSize specifies the size of the last
OAM Echo message sent as part of an 'mtuPing' test.
Setting this object to a non-zero value is a … | column | Octets Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.12 |
| tnOamPingCtlMtuStepSize Specifies the number of octets by which to increment the
OAM Echo message request size for each message request sent
when tnOamPingCtlTestMode is set equal to 'mtuPing'. If the
n… | column | Octets Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.13 |
| tnOamPingCtlTargetIpAddress obsolete Specifies the Ipv4 address to be used as the destination for
performing an OAM ping operation when tnOamPingCtlTestMode has
a value of 'svcPing' or 'vprnPing'. This parameter is
… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.14 |
| tnOamPingCtlServiceId The value of tnOamPingCtlServiceId specifies the service ID of the
service being tested.
The applicability of tnOamPingCtlServiceId varies with the test type,
as sh… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.15 |
| tnOamPingCtlLocalSdp When the value of tnOamPingCtlLocalSdp is 'true', the 'svcPing' test
determines an egress SDP-ID that is bound to the service that has
the far-end IP address specified in tnOamPin… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.16 |
| tnOamPingCtlRemoteSdp The value of tnOamPingCtlRemoteSdp specifies the encapsulation of the
ping reply to be sent by the far end node.
When tnOamPingCtlRemoteSdp is 'false', the far-end … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.17 |
| tnOamPingCtlSize The value of tnOamPingCtlSize specifies the size of the OAM Echo
message.
This parameter is optional and is valid only if tnOamPingCtlTestMode
has a value of 'sdpPi… | column | octets Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.18 |
| tnOamPingCtlTimeOut The value of tnOamPingCtlTimeOut specifies the time-out value,
in milliseconds, to be used during a test run.
Timers (with duration configured using the tnOamPingCt… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.19 |
| tnOamPingCtlRowStatus This object allows entries to be created and deleted
in the tnOamPingCtlTable. Deletion of an entry in this
table results in all corresponding (same
tnOamPingCtlOwnerIndex and tn… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.2 |
| tnOamPingCtlProbeCount The value of tnOamPingCtlProbeCount specifies the number of probes to
send during the test.
The maximum probe count depends on the value of tnOamPingCtlTestMode,
as… | column | probes Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.20 |
| tnOamPingCtlInterval The value of tnOamPingCtlInterval specifies the time to wait between
the transmission of one OAM Echo request and the next.
The applicability, range, and default va… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.21 |
| tnOamPingCtlMaxRows obsolete The maximum number of entries allowed in the tnOamPingHistoryTable
for this OAM ping test. The agent will remove the oldest entry in
the tnOamPingHistoryTable to allow the additi… | column | rows SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.22 |
| tnOamPingCtlTrapGeneration The value of tnOamPingCtlTrapGeneration specifies the
notification(s) to send for a test run.
Each bit enables the transmission of one notification, as follows.
'pr… | column | Bits | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.23 |
| tnOamPingCtlTrapProbeFailureFilter The value of this object is used to determine when
to generate a tnOamPingProbeFailed NOTIFICATION.
Setting tnOamPingCtlTrapGeneration
to 'probeFailure (0)' implies… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.24 |
| tnOamPingCtlTrapTestFailureFilter The value of this object is used to determine when
to generate a tnOamPingTestFailed NOTIFICATION.
Setting tnOamPingCtlTrapGeneration to 'testFailure (1)'
implies t… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.25 |
| tnOamPingCtlSAA The value of tnOamPingCtlSAA specifies if this test is an SAA test
(Service Assurance Agent; 'true'), or an OAM test ('false'). If
there is a tnOamSaaCtlTable row with the specif… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.26 |
| tnOamPingCtlRuns The value of tnOamPingCtlRuns indicates the number of times
this OAM ping test has been executed. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.27 |
| tnOamPingCtlFailures The value of tnOamPingCtlFailures indicates the number of times
this OAM ping test has failed. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.28 |
| tnOamPingCtlLastRunResult The value of tnOamPingCtlLastRunResult indicates the completion
status the last time this test was executed. If this OAM test is
currently in progress, this object indicates the … | column | TmnxOamTestResult | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.29 |
| tnOamPingCtlStorageType The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row. | column | SNMPv2-TCStorageType | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.3 |
| tnOamPingCtlLastChanged The value of tnOamPingCtlLastChanged indicates the time the
value of a settable object in this row was last changed. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.30 |
| tnOamPingCtlVRtrID The value of tnOamPingCtlVRtrID specifies the virtual router to be
used for the test. The value specified must be the index of an active
row in TIMETRA-VRTR-MIB::vRtrConfTable.
… | column | TN-TC-MIBTmnxVRtrID | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.31 |
| tnOamPingCtlTgtAddrType The value of tnOamPingCtlTgtAddrType specifies the address type of
tnOamPingCtlTgtAddress.
Values supported depend on tnOamPingCtlTestMode, as follows.
'cpePing '… | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.32 |
| tnOamPingCtlTgtAddress The value of tnOamPingCtlTgtAddress specifies the destination IP host
address to be used when performing an OAM ping operation. The
corresponding address type is configured using… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.33 |
| tnOamPingCtlSrcAddrType The value of tnOamPingCtlSrcAddrType specifies the address type of
tnOamPingCtlSrcAddress.
Only 'ipv4' and 'ipv6' address types are supported. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.34 |
| tnOamPingCtlSrcAddress The value of tnOamPingCtlSrcAddress specifies the source IP host
address to be used when performing an OAM ping operation. The
corresponding address type is configured using
tnOa… | column | OctetString | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.35 |
| tnOamPingCtlDnsName The value of tnOamPingCtlDnsName specifies the DNS name to
be resolved to an IP address.
This object is required for 'dnsPing'. | column | OctetString | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.36 |
| tnOamPingCtlDNSRecord The value of tnOamPingCtlDNSRecord specifies which DNS record
is to be retrieved in this test. | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.37 |
| tnOamPingCtlIntervalUnits The value of tnOamPingCtlIntervalUnits specifies the units for
tnOamPingCtlInterval. For example, if tnOamPingCtlIntervalUnits
has the value 'centiseconds(2)', and tnOamPingCtlIn… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.38 |
| tnOamPingCtlDescr The purpose of this object is to provide a
descriptive name of the OAM ping test. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.4 |
| tnOamPingCtlAdminStatus Reflects the desired state that a tnOamPingCtlEntry should be
in:
enabled(1) - Attempt to activate the test as defined by
this tnOamPingCtlEntry.… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.6 |
| tnOamPingCtlOrigSdpId Specifies the originating SDP-ID to be used for performing
a sdp-ping or mtu-ping operation. This parameter is required
only if tnOamPingCtlTestMode has a value of either 'sdpPin… | column | TN-SERV-MIBSdpId | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.7 |
| tnOamPingCtlRespSdpId Specifies the return SDP-ID to be used by the far-end node for
its message reply. This parameter is optional and is valid only if
tnOamPingCtlTestMode has a value of 'sdpPing'.
… | column | TN-SERV-MIBSdpId | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.8 |
| tnOamPingCtlFcName The value of tnOamPingCtlFcName specifies the forwarding class to be
used when launching the probe(s). The forwarding class name must be
present in the index column of TIMETRA-QO… | column | TN-TC-MIBTFCName | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.9 |