tnOamPingCtlSize
TN-OAM-TEST-MIB ·
.1.3.6.1.4.1.7483.6.1.2.11.1.4.1.18
Object
column
r/w
octets Unsigned32
The value of tnOamPingCtlSize specifies the size of the OAM Echo
message.
This parameter is optional and is valid only if tnOamPingCtlTestMode
has a value of 'sdpPing', 'macPing', 'lspPing', 'vprnPing',
'mfibPing', 'vccvPing', 'icmpPing', 'p2mpLspPing', 'ethCfmLoopback',
or 'ethCfmTwoWaySlm'.
The minimum, maximum, and default values for the
tnOamPingCtlTestMode cases are:
'ethCfmLoopback' : 0, 1500, 0
'ethCfmTwoWaySlm': 0, 1500, 0
'ethCfmTwoWayDelay': 0, 1500, 0
'ethCfmOneWayDelay': 0, 1500, 0
'icmpPing' : 0, 16384, 56
'lspPing' : 80, 9198, 80 - LSP prefix specified
: 92, 9198, 92 - LSP name specified
'macPing' : 1, 9198, 72
'mfibPing' : 1, 9198, 72
'p2mpLspPing' : 92|97, 9198, 92 - LSP name, 0 S2L specified
: 104|109, 9198, 104 - LSP name, 1 S2L specified
: 112|117, 9198, 112 - LSP name, 2 S2L specified
: 120|125, 9198, 120 - LSP name, 3 S2L specified
: 128|133, 9198, 128 - LSP name, 4 S2L specified
: 136|141, 9198, 136 - LSP name, 5 S2L specified
: 88|93, 9198, 88 - LDP id, 0 leaf-addr specified
: 100|105, 9198, 100 - LDP id, 1 leaf-addr specified
: 108|113, 9198, 108 - LDP id, 2 leaf-addr specified
: 116|121, 9198, 116 - LDP id, 3 leaf-addr specified
: 124|129, 9198, 124 - LDP id, 4 leaf-addr specified
: 132|137, 9198, 132 - LDP id, 5 leaf-addr specified
: 92|97, 9198, 92 - LDP SSM, 0 leaf-addr specified
: 104|109, 9198, 104 - LDP SSM, 1 leaf-addr specified
: 112|117, 9198, 112 - LDP SSM, 2 leaf-addr specified
: 120|125, 9198, 120 - LDP SSM, 3 leaf-addr specified
: 128|133, 9198, 128 - LDP SSM, 4 leaf-addr specified
: 136|141, 9198, 136 - LDP SSM, 5 leaf-addr specified
'sdpPing' : 72, 9198, 72
'vccvPing' : 88, 9198, 88 - FEC 128 pseudowire
: 120, 9198, 120 - FEC 129 pseudowire
'vprnPing' : 1, 9198, 72
An RSVP-TE P2MP LSP consists of source-to-leaf (S2L) sub-LSPs.
For P2MP LSP ping, a gap in the supported range of tnOamPingCtlSize
arises from the inclusion of the Pad TLV (see RFC 4379 section 3.4).
For example, when no S2L sub-LSP is specified for a RSVP P2MP LSP,
the minimum ping size is 92. But the next valid minimum ping size
is 97 due to the inclusion of the Pad TLV.
When the OAM message is encapsulated in an IP/GRE SDP, the
IP 'DF' (Don't Fragment) bit is set. If any segment of the path
between the sender and receiver cannot handle the message size,
the message is discarded. MPLS LSPs are not expected to fragment
the message either, as the message contained in the LSP is not an
IP packet.
When tnOamPingCtlTestMode has a value of 'ethCfmLoopback', or
'ethCfmTwoWaySlm' the value of this object specifies the number of
octets in the Value field of the Data TLV of the Ethernet CFM packet.
If zero is specified, the packet has no Data TLV.
When tnOamPingCtlTestMode has a value of 'icmpPing', the value
of this object specifies the payload size following the ICMP
header.
When tnOamPingCtlTestMode has a value of 'mtuPing', changing the
message size is a method of checking the ability of an SDP
to support a particular path-mtu value. The size of the message
does not include the SDP encapsulation, VC-Label (if applied)
or any DLC headers or trailers.
Before 6.0 release, the minimum size in 'sdpPing' is 40 octets.
Such shorter packet has no timestamp information but should still
be accepted for interoperability purpose. However, new 'sdpPing'
should include the timestamp information.
Context
- MIB
- TN-OAM-TEST-MIB
- OID
.1.3.6.1.4.1.7483.6.1.2.11.1.4.1.18- Type
- column
- Access
- readwrite
- Status
- current
- Units
- octets
- Parent
- tnOamPingCtlEntry
- Table
- tnOamPingCtlTable
- Siblings
- 37
Syntax
octets Unsigned32
Values & Constraints
Object Constraints
range: 0-16384
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| tnOamPingCtlTestIndex The test name index of the Nokia SROS OAM ping test.
This is locally unique, within the scope of an
tnOamPingCtlOwnerIndex. | column | OctetString | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.1 |
| tnOamPingCtlProfile The value of tnOamPingCtlProfile specifies the profile to be used
with the forwarding class specified in tnOamPingCtlFcName. This
object is optional.
As shown in t… | column | TN-TC-MIBTProfile | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.10 |
| tnOamPingCtlMtuStartSize The value of tnOamPingCtlMtuStartSize specifies the size of the first
OAM Echo message sent as part of an 'mtuPing' test.
Setting this object to a non-zero value is… | column | Octets Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.11 |
| tnOamPingCtlMtuEndSize The value of tnOamPingCtlMtuEndSize specifies the size of the last
OAM Echo message sent as part of an 'mtuPing' test.
Setting this object to a non-zero value is a … | column | Octets Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.12 |
| tnOamPingCtlMtuStepSize Specifies the number of octets by which to increment the
OAM Echo message request size for each message request sent
when tnOamPingCtlTestMode is set equal to 'mtuPing'. If the
n… | column | Octets Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.13 |
| tnOamPingCtlTargetIpAddress obsolete Specifies the Ipv4 address to be used as the destination for
performing an OAM ping operation when tnOamPingCtlTestMode has
a value of 'svcPing' or 'vprnPing'. This parameter is
… | column | SNMPv2-SMIIpAddress | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.14 |
| tnOamPingCtlServiceId The value of tnOamPingCtlServiceId specifies the service ID of the
service being tested.
The applicability of tnOamPingCtlServiceId varies with the test type,
as sh… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.15 |
| tnOamPingCtlLocalSdp When the value of tnOamPingCtlLocalSdp is 'true', the 'svcPing' test
determines an egress SDP-ID that is bound to the service that has
the far-end IP address specified in tnOamPin… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.16 |
| tnOamPingCtlRemoteSdp The value of tnOamPingCtlRemoteSdp specifies the encapsulation of the
ping reply to be sent by the far end node.
When tnOamPingCtlRemoteSdp is 'false', the far-end … | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.17 |
| tnOamPingCtlTimeOut The value of tnOamPingCtlTimeOut specifies the time-out value,
in milliseconds, to be used during a test run.
Timers (with duration configured using the tnOamPingCt… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.19 |
| tnOamPingCtlRowStatus This object allows entries to be created and deleted
in the tnOamPingCtlTable. Deletion of an entry in this
table results in all corresponding (same
tnOamPingCtlOwnerIndex and tn… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.2 |
| tnOamPingCtlProbeCount The value of tnOamPingCtlProbeCount specifies the number of probes to
send during the test.
The maximum probe count depends on the value of tnOamPingCtlTestMode,
as… | column | probes Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.20 |
| tnOamPingCtlInterval The value of tnOamPingCtlInterval specifies the time to wait between
the transmission of one OAM Echo request and the next.
The applicability, range, and default va… | column | milliseconds Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.21 |
| tnOamPingCtlMaxRows obsolete The maximum number of entries allowed in the tnOamPingHistoryTable
for this OAM ping test. The agent will remove the oldest entry in
the tnOamPingHistoryTable to allow the additi… | column | rows SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.22 |
| tnOamPingCtlTrapGeneration The value of tnOamPingCtlTrapGeneration specifies the
notification(s) to send for a test run.
Each bit enables the transmission of one notification, as follows.
'pr… | column | Bits | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.23 |
| tnOamPingCtlTrapProbeFailureFilter The value of this object is used to determine when
to generate a tnOamPingProbeFailed NOTIFICATION.
Setting tnOamPingCtlTrapGeneration
to 'probeFailure (0)' implies… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.24 |
| tnOamPingCtlTrapTestFailureFilter The value of this object is used to determine when
to generate a tnOamPingTestFailed NOTIFICATION.
Setting tnOamPingCtlTrapGeneration to 'testFailure (1)'
implies t… | column | Unsigned32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.25 |
| tnOamPingCtlSAA The value of tnOamPingCtlSAA specifies if this test is an SAA test
(Service Assurance Agent; 'true'), or an OAM test ('false'). If
there is a tnOamSaaCtlTable row with the specif… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.26 |
| tnOamPingCtlRuns The value of tnOamPingCtlRuns indicates the number of times
this OAM ping test has been executed. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.27 |
| tnOamPingCtlFailures The value of tnOamPingCtlFailures indicates the number of times
this OAM ping test has failed. | column | SNMPv2-SMICounter32 | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.28 |
| tnOamPingCtlLastRunResult The value of tnOamPingCtlLastRunResult indicates the completion
status the last time this test was executed. If this OAM test is
currently in progress, this object indicates the … | column | TmnxOamTestResult | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.29 |
| tnOamPingCtlStorageType The storage type for this conceptual row.
Conceptual rows having the value 'permanent' need not
allow write-access to any columnar objects in the row. | column | SNMPv2-TCStorageType | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.3 |
| tnOamPingCtlLastChanged The value of tnOamPingCtlLastChanged indicates the time the
value of a settable object in this row was last changed. | column | SNMPv2-TCTimeStamp | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.30 |
| tnOamPingCtlVRtrID The value of tnOamPingCtlVRtrID specifies the virtual router to be
used for the test. The value specified must be the index of an active
row in TIMETRA-VRTR-MIB::vRtrConfTable.
… | column | TN-TC-MIBTmnxVRtrID | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.31 |
| tnOamPingCtlTgtAddrType The value of tnOamPingCtlTgtAddrType specifies the address type of
tnOamPingCtlTgtAddress.
Values supported depend on tnOamPingCtlTestMode, as follows.
'cpePing '… | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.32 |
| tnOamPingCtlTgtAddress The value of tnOamPingCtlTgtAddress specifies the destination IP host
address to be used when performing an OAM ping operation. The
corresponding address type is configured using… | column | INET-ADDRESS-MIBInetAddress | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.33 |
| tnOamPingCtlSrcAddrType The value of tnOamPingCtlSrcAddrType specifies the address type of
tnOamPingCtlSrcAddress.
Only 'ipv4' and 'ipv6' address types are supported. | column | INET-ADDRESS-MIBInetAddressType | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.34 |
| tnOamPingCtlSrcAddress The value of tnOamPingCtlSrcAddress specifies the source IP host
address to be used when performing an OAM ping operation. The
corresponding address type is configured using
tnOa… | column | OctetString | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.35 |
| tnOamPingCtlDnsName The value of tnOamPingCtlDnsName specifies the DNS name to
be resolved to an IP address.
This object is required for 'dnsPing'. | column | OctetString | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.36 |
| tnOamPingCtlDNSRecord The value of tnOamPingCtlDNSRecord specifies which DNS record
is to be retrieved in this test. | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.37 |
| tnOamPingCtlIntervalUnits The value of tnOamPingCtlIntervalUnits specifies the units for
tnOamPingCtlInterval. For example, if tnOamPingCtlIntervalUnits
has the value 'centiseconds(2)', and tnOamPingCtlIn… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.38 |
| tnOamPingCtlDescr The purpose of this object is to provide a
descriptive name of the OAM ping test. | column | SNMP-FRAMEWORK-MIBSnmpAdminString | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.4 |
| tnOamPingCtlTestMode Specifies the type of OAM ping test defined by this entry.
The configuration parameters unique to a specific test type are to
be found in an sparsely dependent table extension for… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.5 |
| tnOamPingCtlAdminStatus Reflects the desired state that a tnOamPingCtlEntry should be
in:
enabled(1) - Attempt to activate the test as defined by
this tnOamPingCtlEntry.… | column | Enumeration | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.6 |
| tnOamPingCtlOrigSdpId Specifies the originating SDP-ID to be used for performing
a sdp-ping or mtu-ping operation. This parameter is required
only if tnOamPingCtlTestMode has a value of either 'sdpPin… | column | TN-SERV-MIBSdpId | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.7 |
| tnOamPingCtlRespSdpId Specifies the return SDP-ID to be used by the far-end node for
its message reply. This parameter is optional and is valid only if
tnOamPingCtlTestMode has a value of 'sdpPing'.
… | column | TN-SERV-MIBSdpId | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.8 |
| tnOamPingCtlFcName The value of tnOamPingCtlFcName specifies the forwarding class to be
used when launching the probe(s). The forwarding class name must be
present in the index column of TIMETRA-QO… | column | TN-TC-MIBTFCName | .1.3.6.1.4.1.7483.6.1.2.11.1.4.1.9 |