s5EnRedPortOperStatus

Object

column Enumeration

The redundancy status of the port. The values are:
other(1).............none of the following.
ok(2)...................no fault
localFault(3)....the local port has sensed a fault condition.
remoteFault(4)...the remote port has sensed a fault
                 condition and has signaled the local port
                 accordingly.
              
Either a localFault(3) or remoteFault(4) condition should
cause a healthy redundant port pair to switchover.
If the port does not belong to a redundant pair, a
value of other(1) is returned.
              
Note:  If the redundant link consists of ports without
     remote fault capability, the value remoteFault(4)
     will not be reported and the value localFault(3)
     implies that link is off.

Context

MIB: S5-ETH-REDUNDANT-LINKS-MIB
OID: .1.3.6.1.4.1.45.1.6.6.1.2.1.1.5
Type: column
Access: readonly
Status: current
Parent: s5EnRedPortEntry
Table: s5EnRedPortTable
Siblings: 13

Related Objects

Sibling Objects

Object	Type	Syntax	OID
s5EnRedPortBrdIndx The index of the slot containing the board on which the port is located.	column	Integer32	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.1`
s5EnRedPortModeChanges A count of the number of times this port has transitioned from standby mode to non-standby mode (includes active mode and standalone mode), or vice versa.	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.10`
s5EnRedPortCompanionBrdNum The index of the slot containing the board of the other port in the redundant pair. If the port (whose slot-port identity is given by the instance) is hardware-red…	column	Integer32	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.11`
s5EnRedPortCompanionPortNum The index of the other port in the redundant pair. If the port (whose slot-port identity is given by the instance) is hardware-redundant capable, this object has th…	column	Integer32	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.12`
s5EnRedPortSwitchoverStatus The switchover status of the port (and its companion). The following values can be written: timedSwitchover(2)...cause a timed switchover (see value of …	column	Enumeration	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.13`
s5EnRedPortSwitchoverTime The length of time between switching over a redundant port pair and switching back, when a timed switchover is done to the port. This object can only be written in the same reques…	column	Integer32	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.14`
s5EnRedPortPortIndx The index of the port on the board.	column	Integer32	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.2`
s5EnRedPortCapability The redundancy capability of the port: hwRedOnly(1).....hardware redundancy only. swRedOnly(2).....software redundacy only. hwAndSwRed(3)....both hardware and software redundancy.…	column	Enumeration	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.3`
s5EnRedPortRedundMode The redundancy mode of the port. The values when written change the redundancy mode, and when read report the redundancy mode: standalone(1)..the port is not in …	column	Enumeration	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.4`
s5EnRedPortRemoteOperStatus This object reflects the real time status of the received data from the remote port. The values are: snpxFLRemFltCpblPortUp(1)....10BASE-FL signaling, …	column	Enumeration	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.6`
s5EnRedPortRemFltSelectMode This mode specifies the set of local fault events which will cause a switchover. The values are: synoptics(1)..The SynOptics Tx Remote Fault events consist of a…	column	Enumeration	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.7`
s5EnRedPortTxMode The Transmit Fiber Mode, which determines the port transmit idle. The values are: autoCfg(1)...The port will auto configure based upon the received idle. fl(2).…	column	Enumeration	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.8`
s5EnRedPortFaults A count of local or remote faults on this port. This counter increments on a transition between the fault and no-fault states.	column	SNMPv2-SMICounter32	`.1.3.6.1.4.1.45.1.6.6.1.2.1.1.9`

`1`	other
`2`	ok
`3`	localFault
`4`	remoteFault

Object

Context

Syntax

Values & Constraints

Related Objects