wdmCtrlChannelOuputPowerControlFailure
LUM-WDM-MIB ·
.1.3.6.1.4.1.8708.2.4.2.8.1.1.13
Object
column
LUM-TCFaultStatus
Alarm raised when the wanted output power
can not be obtained. That is
a) The wanted power has not been obtained after the
maximum number of consequent control cycles.
b) Failure to read the current output power.
c) Failure to set attenuation when regulating
channel.
Context
- MIB
- LUM-WDM-MIB
- OID
.1.3.6.1.4.1.8708.2.4.2.8.1.1.13- Type
- column
- Access
- readonly
- Status
- current
- Parent
- wdmCtrlChannelEntry
- Table
- wdmCtrlChannelTable
- Siblings
- 27
Values & Constraints
Type Values
1 | ok |
2 | alarm |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wdmCtrlChannelIndex An index assigned to each entry. The index contains information
about subrack, slot and port for controlled channel. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.1 |
| wdmCtrlChannelCurrentOutputPower The actual output power. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.10 |
| wdmCtrlChannelCurrentAttenuation The current attenuation. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.11 |
| wdmCtrlChannelForceRegulationCommand Starts a regulation manually | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.8.1.1.12 |
| wdmCtrlChannelCurrentPowerOutOfRange Alarm raised when the current output power
is outside the 'regulation range' for the group.
At this point, no regulation will be performed on
the channel. The opera… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.14 |
| wdmCtrlChannelAttenuationOutOfRange Alarm raised when the attenuation is at the maximum
or minimum values for the controlled device and the
wantedOutputPower cannot be obtained.
At this point, no regu… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.15 |
| wdmCtrlChannelStatus The regulation status of the channel.
initial - No regulation has been performed yet.
searching - The system is trying to detect the channel.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.8.1.1.16 |
| wdmCtrlChannelStartupChannel Initiates a safe startup procedure for the channel
when set to 'start'.
If the administrative status of the channel is
'down' or the channel is not detected by the … | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.8.1.1.17 |
| wdmCtrlChannelMonitorIndex Shows the index of the connected monitor interface. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.18 |
| wdmCtrlChannelStartupCommand Initiates a safe startup sequence for the
channel. If the administrative status of the channel
is 'down' or the channel is not detected by the
monitor unit, the system attempts to… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.8.1.1.19 |
| wdmCtrlChannelName The management name of the channel, for example
'ch:1:2:1:959'
(ch:[subrack]:[slot]:[port]:[channel]). | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.4.2.8.1.1.2 |
| wdmCtrlChannelSfpMissing An expected SFP is missing.
A(ctivation): An expected SFP is missing.
D(e-activation): The missing SFP is inserted. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.20 |
| wdmCtrlChannelSfpMediaMismatch The type of the SFP used for the channel port
is not the expected.
A(ctivation): Invalid or mismatching SFP media is
detected.
D(e-activation): The… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.21 |
| wdmCtrlChannelLossOfSignal Loss of signal at the channel port.
A(ctivation): Active loss of signal HW
indication.
D(e-activation): Inactive loss of signal HW
indication. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.22 |
| wdmCtrlChannelDescr User configurable label.
This attribute can be written via SNMP. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.4.2.8.1.1.23 |
| wdmCtrlChannelMaxAttenuation The max attenuation limit on channel. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.24 |
| wdmCtrlChannelMinAttenuation The min attenuation limit on channel. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.25 |
| wdmCtrlChannelAttenControlOffset The threshold offset to max/min attenuation on the channel.
If the threshold is reached, AttenControlDegraded alarm will be raised. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.26 |
| wdmCtrlChannelAttenControlDegraded Alarm is raised when channel attenuation
is crossing threshold to max/min attenuation.
A(ctivation): Active the alarm indication.
D(e-activation): In… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.27 |
| wdmCtrlChannelNotFound Channel not found. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.28 |
| wdmCtrlChannelSubrack The subrack number of the unit where the controlled
channel is attenuated. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.4.2.8.1.1.3 |
| wdmCtrlChannelSlot The slot number of the unit where the controlled
channel is attenuated. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.4.2.8.1.1.4 |
| wdmCtrlChannelTxPort The port number of the controlled channel in the unit where
the channel is attenuated. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.4.2.8.1.1.5 |
| wdmCtrlChannelChannel The frequency of the 'wavelength' given in
hundreds of GHz (0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.4.2.8.1.1.6 |
| wdmCtrlChannelGroupNumber The number of the group to which the controlled
channel belongs. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.7 |
| wdmCtrlChannelAdminStatus The administrative state for the channel control.
down - The channel control is inactive. Channel
attenuation is set to its maximum value.
service - … | column | LUM-TCBoardOrInterfaceAdminStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.8 |
| wdmCtrlChannelWantedOutputPower The wanted output power. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.9 |