wdmCtrlChannelAdminStatus
LUM-WDM-MIB ·
.1.3.6.1.4.1.8708.2.4.2.8.1.1.8
Object
The administrative state for the channel control.
down - The channel control is inactive. Channel
attenuation is set to its maximum value.
service - The channel control is activated but
alarms are suppressed. Intended for use during
service or re-configuration. When service is
concluded adminStatus should be set to 'up' again.
up - The channel control is active. Alarms are
not suppressed.
Context
- MIB
- LUM-WDM-MIB
- OID
.1.3.6.1.4.1.8708.2.4.2.8.1.1.8- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- wdmCtrlChannelEntry
- Table
- wdmCtrlChannelTable
- Siblings
- 27
Values & Constraints
Type Values
1 | down |
2 | service |
3 | up |
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| wdmCtrlChannelIndex An index assigned to each entry. The index contains information
about subrack, slot and port for controlled channel. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.1 |
| wdmCtrlChannelCurrentOutputPower The actual output power. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.10 |
| wdmCtrlChannelCurrentAttenuation The current attenuation. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.11 |
| wdmCtrlChannelForceRegulationCommand Starts a regulation manually | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.8.1.1.12 |
| wdmCtrlChannelOuputPowerControlFailure Alarm raised when the wanted output power
can not be obtained. That is
a) The wanted power has not been obtained after the
maximum number of consequent control cycl… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.13 |
| wdmCtrlChannelCurrentPowerOutOfRange Alarm raised when the current output power
is outside the 'regulation range' for the group.
At this point, no regulation will be performed on
the channel. The opera… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.14 |
| wdmCtrlChannelAttenuationOutOfRange Alarm raised when the attenuation is at the maximum
or minimum values for the controlled device and the
wantedOutputPower cannot be obtained.
At this point, no regu… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.15 |
| wdmCtrlChannelStatus The regulation status of the channel.
initial - No regulation has been performed yet.
searching - The system is trying to detect the channel.
… | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.8.1.1.16 |
| wdmCtrlChannelStartupChannel Initiates a safe startup procedure for the channel
when set to 'start'.
If the administrative status of the channel is
'down' or the channel is not detected by the … | column | Enumeration | .1.3.6.1.4.1.8708.2.4.2.8.1.1.17 |
| wdmCtrlChannelMonitorIndex Shows the index of the connected monitor interface. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.18 |
| wdmCtrlChannelStartupCommand Initiates a safe startup sequence for the
channel. If the administrative status of the channel
is 'down' or the channel is not detected by the
monitor unit, the system attempts to… | column | LUM-TCCommandString | .1.3.6.1.4.1.8708.2.4.2.8.1.1.19 |
| wdmCtrlChannelName The management name of the channel, for example
'ch:1:2:1:959'
(ch:[subrack]:[slot]:[port]:[channel]). | column | LUM-TCMgmtNameString | .1.3.6.1.4.1.8708.2.4.2.8.1.1.2 |
| wdmCtrlChannelSfpMissing An expected SFP is missing.
A(ctivation): An expected SFP is missing.
D(e-activation): The missing SFP is inserted. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.20 |
| wdmCtrlChannelSfpMediaMismatch The type of the SFP used for the channel port
is not the expected.
A(ctivation): Invalid or mismatching SFP media is
detected.
D(e-activation): The… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.21 |
| wdmCtrlChannelLossOfSignal Loss of signal at the channel port.
A(ctivation): Active loss of signal HW
indication.
D(e-activation): Inactive loss of signal HW
indication. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.22 |
| wdmCtrlChannelDescr User configurable label.
This attribute can be written via SNMP. | column | SNMPv2-TCDisplayString | .1.3.6.1.4.1.8708.2.4.2.8.1.1.23 |
| wdmCtrlChannelMaxAttenuation The max attenuation limit on channel. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.24 |
| wdmCtrlChannelMinAttenuation The min attenuation limit on channel. | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.25 |
| wdmCtrlChannelAttenControlOffset The threshold offset to max/min attenuation on the channel.
If the threshold is reached, AttenControlDegraded alarm will be raised. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.26 |
| wdmCtrlChannelAttenControlDegraded Alarm is raised when channel attenuation
is crossing threshold to max/min attenuation.
A(ctivation): Active the alarm indication.
D(e-activation): In… | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.27 |
| wdmCtrlChannelNotFound Channel not found. | column | LUM-TCFaultStatus | .1.3.6.1.4.1.8708.2.4.2.8.1.1.28 |
| wdmCtrlChannelSubrack The subrack number of the unit where the controlled
channel is attenuated. | column | LUM-TCSubrackNumber | .1.3.6.1.4.1.8708.2.4.2.8.1.1.3 |
| wdmCtrlChannelSlot The slot number of the unit where the controlled
channel is attenuated. | column | LUM-TCSlotNumber | .1.3.6.1.4.1.8708.2.4.2.8.1.1.4 |
| wdmCtrlChannelTxPort The port number of the controlled channel in the unit where
the channel is attenuated. | column | LUM-TCPortNumber | .1.3.6.1.4.1.8708.2.4.2.8.1.1.5 |
| wdmCtrlChannelChannel The frequency of the 'wavelength' given in
hundreds of GHz (0.01 GHz). | column | LUM-TCLambdaFrequency | .1.3.6.1.4.1.8708.2.4.2.8.1.1.6 |
| wdmCtrlChannelGroupNumber The number of the group to which the controlled
channel belongs. | column | Unsigned32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.7 |
| wdmCtrlChannelWantedOutputPower The wanted output power. | column | Integer32 | .1.3.6.1.4.1.8708.2.4.2.8.1.1.9 |