Juniper-FRAME-RELAY-MIB Table View

Table-centric layout grouping table, row, and column objects.

Tables
9
Rows
9
Columns
76
.1.3.6.1.4.1.4874.2.2.10.1.1.2 · 1 row entry · 18 columns
The Parameters for the Data Link Connection Management Interface for
the frame relay service on this interface.
          
This table represents a superset of functionality specified in the
FRAME-RELAY-DTE-MIB.  In particular, it adds attributes that permit the
interface to operate as a network-side (DCE) interface.
juniFrDlcmiEntry entry .1.3.6.1.4.1.4874.2.2.10.1.1.2.1
The Parameters for a particular Data Link Connection Management
Interface.

Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/juniIfTable, and
ju…
Indexes
juniFrDlcmiIfIndex
Column Syntax OID
juniFrDlcmiIfIndex
The ifIndex value of the corresponding ifEntry.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.1
juniFrDlcmiState
This variable states which Data Link Connection Management scheme is
active (and by implication, what DLCI it uses) on the Frame Relay
interface.
Enumerationr/w
Enumerated Values:
1noLmiConfigured
2lmiRev1
3ansiT1617D
4ansiT1617B
5itut933A
6ansiT1617D1994
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.2
juniFrDlcmiAddress
This variable states which address format is in use on the Frame Relay
interface.
Enumerationr/w
Enumerated Values:
1q921
2q922March90
3q922November90
4q922
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.3
juniFrDlcmiAddressLen
This variable states the address length in octets. In the case of Q922
format, the length indicates the entire length of the address including
the control portion.
Enumerationr/w
Enumerated Values:
2twoOctets
3threeOctets
4fourOctets
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.4
juniFrDlcmiPollingInterval
This is the number of seconds between successive status enquiry
messages sent by the DTE.

Pertains to DTE/NNI operation only. This parameter can be reconfigured
only when the Frame Relay interface is act…
secondsInteger32r/w
Constraints:
range: 5-30
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.5
juniFrDlcmiFullEnquiryInterval
Number of status enquiry intervals that pass before issuance of a full
status enquiry message.

Pertains to DTE/NNI operation only. This parameter can be reconfigured
only when the Frame Relay interface i…
Integer32r/w
Constraints:
range: 1-255
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.6
juniFrDlcmiErrorThreshold
The minimum number of errors that must be observed within the number of
events specified by juniFrDlcmiMonitoredEvents, to declare the interface
down.

'error' is lack of receipt of a Status, in response t…
Integer32r/w
Constraints:
range: 1-10
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.7
juniFrDlcmiMonitoredEvents
The number of status polling intervals over which the error threshold
is counted. For example, if within 'MonitoredEvents' number of events
the station receives 'ErrorThreshold' number of errors, the interface is
marke…
Integer32r/w
Constraints:
range: 1-10
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.8
juniFrDlcmiMaxSupportedVCs
The maximum number of Virtual Circuits allowed for this interface.
Usually dictated by the Frame Relay network.

In response to a SET, if a value less than zero or higher than the
agent's maximal capabilit…
FRAME-RELAY-DTE-MIBDLCIr/w
Textual Convention: FRAME-RELAY-DTE-MIBDLCI Integer32
Type Constraints:
range: 0..8388607
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.9
juniFrDlcmiMulticast
This indicates whether the Frame Relay interface is using a multicast
service.
Enumerationr/w
Enumerated Values:
1nonBroadcast
2broadcast
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.10
juniFrDlcmiStatus
This indicates the status of the Frame Relay interface as determined by
the performance of the DLCMI. If no DLCMI is running, the Frame Relay
interface will stay in the running state indefinitely.
Enumeration
Enumerated Values:
1running
2fault
3initializing
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.11
juniFrDlcmiRowStatus
Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

To create an entry in this …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.12
juniFrDlcmiLowerIfIndex
The ifIndex of an interface over which this Frame Relay interface is to
be layered. A value of zero indicates no layering. An implementation
may choose to require that a nonzero value be configured at entry
creation. …
IF-MIBInterfaceIndexOrZeror/w
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.13
juniFrDlcmiRole
Specifies the role this interface assumes with respect to the remote
end.

When acting as a DTE, the following objects are not relevant:
juniFrDlcmiDcePollingInterval
juniFrDlcmiDceErrorThreshold
Enumerationr/w
Enumerated Values:
0dte
1dce
2nni
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.14
juniFrDlcmiDcePollingInterval
The number of seconds within which a DCE expects to receive a Status
Enquiry from the DTE.

This value corresponds to the T392 timer.

Pertains to DCE/NNI operation only. This parameter can …
secondsInteger32r/w
Constraints:
range: 5-30
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.15
juniFrDlcmiDceErrorThreshold
The minimum number of errors that must be observed within the number of
events specified by juniFrDlcmiDceMonitoredEvents, to declare the
interface down.

'error' is lack of receipt of a Status Enquiry wit…
Integer32r/w
Constraints:
range: 1-10
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.16
juniFrDlcmiDceMonitoredEvents
The number of DCE polling intervals over which accumulated errors are
counted against the threshold specified in juniFrDlcmiDceErrorThreshold.

If, within this number of events, the number of errors equals…
Integer32r/w
Constraints:
range: 1-10
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.17
juniFrDlcmiMultilinkFrBundleName
This represents multilink frame relay bundle name. This object must be
configured to associate the bundle name to the frame relay major
interface to support the multilink frame relay encapsulation. For
non-multilink f…
JuniFrMlFrBundleNamer/w
Textual Convention: JuniFrMlFrBundleName OctetString
Type Constraints:
range: 0..32
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.18
.1.3.6.1.4.1.4874.2.2.10.1.1.3 · 1 row entry · 17 columns
The statistics for the Data Link Connection Management Interface for
the frame relay service on this interface.
juniFrDlcmiStatsEntry entry .1.3.6.1.4.1.4874.2.2.10.1.1.3.1
The statistics for a particular Data Link Connection Management
Interface.

Statistics are not relevant while the juniFrDlcmiState has the value
'noLmiConfigured'.

The DTE statistics are relevan…
Indexes
juniFrDlcmiIfIndex
Column Syntax OID
juniFrDlcmiStatsDteEnquiries
Number of Status Enquiries sent (as DTE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.1
juniFrDlcmiStatsDteFullEnquiries
Number of Full Enquiries sent (as DTE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.2
juniFrDlcmiStatsDteEnquiryResponses
Number of Status Enquiry responses received (as DTE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.3
juniFrDlcmiStatsDteFullEnquiryResponses
Number of Full Enquiry responses received (as DTE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.4
juniFrDlcmiStatsDteAsyncUpdates
Number of Asynchronous Updates received (as DTE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.5
juniFrDlcmiStatsDteUnknownRxMessages
Number of unknown messages received (as DTE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.6
juniFrDlcmiStatsDteLossOfSequences
Number of times a discontinuity in sequence numbering of received
messages was detected (as DTE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.7
juniFrDlcmiStatsDteNoResponseTimeouts
Number of timer expirations awaiting a Status message (as DTE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.8
juniFrDlcmiStatsDceEnquiries
Number of Status Enquiries received (as DCE.)
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.9
juniFrDlcmiStatsDceFullEnquiries
Number of Full Enquiries received (as DCE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.10
juniFrDlcmiStatsDceEnquiryResponses
Number of Status Enquiry responses sent (as DCE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.11
juniFrDlcmiStatsDceFullEnquiryResponses
Number of Full Enquiry responses sent (as DCE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.12
juniFrDlcmiStatsDceAsyncUpdates
Number of Asynchronous Updates sent (as DCE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.13
juniFrDlcmiStatsDceUnknownRxMessages
Number of unknown messages received (as DCE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.14
juniFrDlcmiStatsDceLossOfSequences
Number of times a discontinuity in sequence numbering of received
messages was detected (as DCE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.15
juniFrDlcmiStatsDceNoResponseTimeouts
Number of timer expirations awaiting a Status Enquiry (as DCE).
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.16
juniFrDlcmiStatsDiscontinuityTime
Value of sysUpTime at the most recent event that caused a discontinuity
in the monotonic operation of any of the counters in this entry. Such
disruption might be caused by:
Hardware insertion/removal.
Reconfigu…
SNMPv2-SMITimeTicks
Textual Convention: SNMPv2-SMITimeTicks Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.3.1.17
.1.3.6.1.4.1.4874.2.2.10.1.1.4 · 1 row entry · 23 columns
A table containing information about specific Data Link Connections
(DLC) or virtual circuits.
          
This table mirrors the structure of FRAME-RELAY-DTE-MIB.frCircuitTable,
for the purpose of enumerating circuits on both DTE and DCE Frame Relay
interfaces.
juniFrCircuitEntry entry .1.3.6.1.4.1.4874.2.2.10.1.1.4.1
The information regarding a single Data Link Connection.
Discontinuities in the counters contained in this table are indicated by
the value in juniFrCircuitCreationTime.
Indexes
juniFrCircuitIfIndex juniFrCircuitDlci
Column Syntax OID
juniFrCircuitIfIndex
The ifIndex Value of the ifEntry this virtual circuit is layered onto.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.1
juniFrCircuitDlci
The Data Link Connection Identifier for this virtual circuit.
FRAME-RELAY-DTE-MIBDLCI
Textual Convention: FRAME-RELAY-DTE-MIBDLCI Integer32
Type Constraints:
range: 0..8388607
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.2
juniFrCircuitState
Indicates whether the particular virtual circuit is operational. In
the absence of a Data Link Connection Management Interface, virtual
circuit entries (rows) may be created by setting virtual circuit state
to 'active'…
Enumerationr/w
Enumerated Values:
1invalid
2active
3inactive
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.3
juniFrCircuitReceivedFECNs
Number of frames received from the network indicating forward
congestion since the virtual circuit was created. This occurs when the
remote DTE sets the FECN flag, or when a switch in the network enqueues
the frame to …
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.4
juniFrCircuitReceivedBECNs
Number of frames received from the network indicating backward
congestion since the virtual circuit was created. This occurs when the
remote DTE sets the BECN flag, or when a switch in the network receives
the frame fr…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.5
juniFrCircuitSentFrames
The number of frames sent from this virtual circuit since it was
created.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.6
juniFrCircuitSentOctets
The number of octets sent from this virtual circuit since it was
created. Octets counted are the full frame relay header and the
payload, but do not include the flag characters or CRC.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.7
juniFrCircuitReceivedFrames
Number of frames received over this virtual circuit since it was
created.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.8
juniFrCircuitReceivedOctets
Number of octets received over this virtual circuit since it was
created. Octets counted include the full frame relay header, but do not
include the flag characters or the CRC.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.9
juniFrCircuitCreationTime
The value of sysUpTime when the virtual circuit was created, whether by
the Data Link Connection Management Interface or by a SetRequest.
SNMPv2-TCTimeStamp
Textual Convention: SNMPv2-TCTimeStamp Unsigned32
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.10
juniFrCircuitLastTimeChange
The value of sysUpTime when last there was a change in the virtual
circuit state
SNMPv2-TCTimeStamp
Textual Convention: SNMPv2-TCTimeStamp Unsigned32
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.11
juniFrCircuitCommittedBurst
This variable indicates the maximum amount of data, in bits, that the
network agrees to transfer under normal conditions, during the
measurement interval. A value of zero (the default) indicates no
commitment.
Integer32r/w
Constraints:
range: 0-2147483647
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.12
juniFrCircuitExcessBurst
This variable indicates the maximum amount of uncommitted data bits
that the network will attempt to deliver over the measurement interval.

By default, if not configured when creating the entry, the Exces…
Integer32r/w
Constraints:
range: 0-2147483647
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.13
juniFrCircuitThroughput
Throughput is the average number of 'Frame Relay Information Field'
bits transferred per second across a user network interface in one
direction, measured over the measurement interval.

If the configured …
Integer32r/w
Constraints:
range: 0-2147483647
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.14
juniFrCircuitMulticast
This indicates whether this VC is used as a unicast VC (i.e. not
multicast) or the type of multicast service subscribed to.
Enumerationr/w
Enumerated Values:
1unicast
2oneWay
3twoWay
4nWay
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.15
juniFrCircuitType
Indication of whether the VC was manually created (static), or
dynamically created (dynamic) via the data link control management
interface.
Enumeration
Enumerated Values:
1static
2dynamic
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.16
juniFrCircuitDiscards
The number of inbound frames dropped because of format errors, or
because the VC is inactive.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.17
juniFrCircuitReceivedDEs
Number of frames received from the network indicating that they were
eligible for discard since the virtual circuit was created. This occurs
when the remote DTE sets the DE flag, or when in remote DTE's switch
detects …
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.18
juniFrCircuitSentDEs
Number of frames sent to the network indicating that they were eligible
for discard since the virtual circuit was created. This occurs when the
local DTE sets the DE flag, indicating that during Network congestion
situ…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.19
juniFrCircuitLogicalIfIndex
Normally the same value as frDlcmiIfIndex, but different when an
implementation associates a virtual ifEntry with a DLC or set of DLCs in
order to associate higher layer objects such as the ipAddrEntry with a
subset of …
IF-MIBInterfaceIndexr/w
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.20
juniFrCircuitRowStatus
This object is used to create a new row or modify or destroy an
existing row in the manner described in the definition of the RowStatus
textual convention. Writable objects in the table may be written in any
RowStatus …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.21
juniFrCircuitSentFECNs
Number of frames sent to the network indicating forward congestion
since the virtual circuit was created. This occurs when the remote DTE
sets the FECN flag, or when a switch in the network enqueues the frame
to a trun…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.22
juniFrCircuitSentBECNs
Number of frames sent to the network indicating backward congestion
since the virtual circuit was created. This occurs when the remote DTE
sets the BECN flag, or when a switch in the network receives the frame
from a t…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.4874.2.2.10.1.1.4.1.23
.1.3.6.1.4.1.4874.2.2.10.1.2.2 · 1 row entry · 4 columns
This table contains entries for Frame Relay Subinterfaces present in
the system.
juniFrSubIfEntry entry .1.3.6.1.4.1.4874.2.2.10.1.2.2.1
Each entry describes the characteristics of a Frame Relay Subinterface.
Creating/deleting entries in this table causes corresponding entries for
be created /deleted in ifTable/ifXTable/juniIfTable.
Indexes
juniFrSubIfIndex
Column Syntax OID
juniFrSubIfIndex
The ifIndex of the Frame Relay Subinterface. When creating entries in
this table, suitable values for this object are determined by reading
juniFrSubNextIfIndex.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.2.2.1.1
juniFrSubIfRowStatus
Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

To create an entry in this …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.4874.2.2.10.1.2.2.1.2
juniFrSubIfLowerIfIndex
The ifIndex of a Frame Relay interface over which this Frame Relay
Subinterface is to be layered. A value of zero indicates no layering.
An implementation may choose to require that a nonzero value be
configured at ent…
IF-MIBInterfaceIndexOrZeror/w
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.2.2.1.3
juniFrSubIfId
An integer identifier for the Frame Relay subinterface, used in
conjunction with the command-line interface. It is provided here for
cross-reference purposes only.

The value must be unique among subinter…
Integer32r/w
Constraints:
range: -1-2147483647
.1.3.6.1.4.1.4874.2.2.10.1.2.2.1.4
.1.3.6.1.4.1.4874.2.2.10.1.2.3 · 1 row entry · 2 columns
This table contains entries for Frame Relay circuits configured on
Frame Relay Subinterfaces present in the system.
          
An implementation may constrain the number of circuits permitted to be
configured per Frame Relay Subinterface; in particular, an
implementation may restrict each Frame Relay Subinterface to have a
single circuit.
          
Attributes in this entry can only be configured at entry creation, and
remain fixed for the lifetime of the entry.
juniFrSubIfCktEntry entry .1.3.6.1.4.1.4874.2.2.10.1.2.3.1
Each entry describes the characteristics of a Frame Relay Subinterface
circuit.
Indexes
juniFrSubIfIndex juniFrSubIfCktDlci
Column Syntax OID
juniFrSubIfCktDlci
The DLCI of the Frame Relay circuit used by this subinterface.
FRAME-RELAY-DTE-MIBDLCI
Textual Convention: FRAME-RELAY-DTE-MIBDLCI Integer32
Type Constraints:
range: 0..8388607
.1.3.6.1.4.1.4874.2.2.10.1.2.3.1.1
juniFrSubIfCktRowStatus
Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

To create an entry in this …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.4874.2.2.10.1.2.3.1.2
.1.3.6.1.4.1.4874.2.2.10.1.3.1 · 1 row entry · 2 columns
This table contains entries for MLFR bundles present in the system.
juniFrMlFrBundleEntry entry .1.3.6.1.4.1.4874.2.2.10.1.3.1.1
Each entry describes the characteristics of a Multilink bundle.
Indexes
juniFrMlFrBundleName
Column Syntax OID
juniFrMlFrBundleName
The administrative name of the multilink bundle associated with this
Frame Relay major interface.
JuniFrMlFrBundleName
Textual Convention: JuniFrMlFrBundleName OctetString
Type Constraints:
range: 0..32
.1.3.6.1.4.1.4874.2.2.10.1.3.1.1.1
juniFrMlFrBundleRowStatus
The rowStatus for this entry. The following sets are supported:
createAndGo(4),
destroy(6)

The following values can be read from this object:
active(1)
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.4874.2.2.10.1.3.1.1.2
.1.3.6.1.4.1.4874.2.2.10.1.3.3 · 1 row entry · 3 columns
This table contains entries for FR link interfaces present in the
system to be added to the multilink bundles.
juniFrMlFrLinkConfigEntry entry .1.3.6.1.4.1.4874.2.2.10.1.3.3.1
Each entry describes the characteristics of FR link interface.
Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/juniIfTable.
Indexes
juniFrMlFrLinkConfigIfIndex
Column Syntax OID
juniFrMlFrLinkConfigIfIndex
The ifIndex of the FR link interface. When creating entries in this
table, suitable values for this object are determined by reading
juniFrMlFrNextLinkIfIndex.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.3.3.1.1
juniFrMlFrLinkConfigLowerIfIndex
The ifIndex of an interface over which this FR link interface is to be
layered. A value of zero indicates no layering. An implementation may
choose to require that a non-zero value be configured at entry
creation.
IF-MIBInterfaceIndexOrZeror/w
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.3.3.1.2
juniFrMlFrLinkConfigRowStatus
Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

To create an entry in this …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.4874.2.2.10.1.3.3.1.3
.1.3.6.1.4.1.4874.2.2.10.1.3.4 · 1 row entry · 4 columns
This table contains entries for FR major interfaces present in the
system which are associated with multilink bundles.
juniFrMlFrMajorConfigEntry entry .1.3.6.1.4.1.4874.2.2.10.1.3.4.1
Each entry describes the characteristics of FR major interface which
have association with the MLFR bundles. Creating/deleting entries in
this table causes corresponding entries for be created/deleted in
ifTable/ifXTab…
Indexes
juniFrMlFrMajorConfigIfIndex
Column Syntax OID
juniFrMlFrMajorConfigIfIndex
The ifIndex of the FR Major interface. When creating entries in this
table, suitable values for this object are determined by reading already
created FR Major interface values.

Each multilink bundle will…
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.3.4.1.1
juniFrMlFrMajorConfigLowerIfIndex
The ifIndex of a FR link interface over which this FR Major interface
is to be layered. On sets, the value of this object must equal on of
the previously created FR link interfaces created in the
juniFrMlFrLinkConfigTa…
IF-MIBInterfaceIndexr/w
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.3.4.1.2
juniFrMlFrMajorBundleName
The MLFR bundle name administratively assigned.
JuniFrMlFrBundleNamer/w
Textual Convention: JuniFrMlFrBundleName OctetString
Type Constraints:
range: 0..32
.1.3.6.1.4.1.4874.2.2.10.1.3.4.1.3
juniFrMlFrMajorRowStatus
Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

To create an entry in this …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.4874.2.2.10.1.3.4.1.4
.1.3.6.1.4.1.4874.2.2.10.1.3.5 · 1 row entry · 3 columns
This table contains entries for FR Link interfaces to FR major
interfaces bindings associated with multilink bundles.
juniFrMlFrLinkBindEntry entry .1.3.6.1.4.1.4874.2.2.10.1.3.5.1
Each entry describes the FR link interface to FR major interface
bindingsi associated with multilink bundles.
Indexes
juniFrMlFrBindMajorIfIndex juniFrMlFrBindLinkIfIndex
Column Syntax OID
juniFrMlFrBindMajorIfIndex
The ifIndex of the FR major interface associated with multilink.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.3.5.1.1
juniFrMlFrBindLinkIfIndex
The ifIndex of a FR link interface bound by the FR major interface
defined by juniFrMlFrBindMajorIfIndex.
IF-MIBInterfaceIndex
Textual Convention: IF-MIBInterfaceIndex Integer32
Type Constraints:
range: 1..2147483647
.1.3.6.1.4.1.4874.2.2.10.1.3.5.1.2
juniFrMlFrBindRowStatus
Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

To create an entry in this …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
.1.3.6.1.4.1.4874.2.2.10.1.3.5.1.3