juniFrDlcmiMultilinkFrBundleName
Juniper-FRAME-RELAY-MIB ·
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.18
Object
column
r/w
JuniFrMlFrBundleName
This represents multilink frame relay bundle name. This object must be configured to associate the bundle name to the frame relay major interface to support the multilink frame relay encapsulation. For non-multilink frame relay, bundle name configuration is not valid and will be ignored.
Context
- MIB
- Juniper-FRAME-RELAY-MIB
- OID
.1.3.6.1.4.1.4874.2.2.10.1.1.2.1.18- Type
- column
- Access
- readwrite
- Status
- current
- Parent
- juniFrDlcmiEntry
- Table
- juniFrDlcmiTable
- Siblings
- 17
Syntax
JuniFrMlFrBundleName
- Source
- JuniFrMlFrBundleName
- Base type
OctetString
Values & Constraints
Type Constraints
range: 0..32
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| juniFrDlcmiIfIndex The ifIndex value of the corresponding ifEntry. | column | IF-MIBInterfaceIndex | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.1 |
| juniFrDlcmiMulticast This indicates whether the Frame Relay interface is using a multicast
service. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.10 |
| juniFrDlcmiStatus This indicates the status of the Frame Relay interface as determined by
the performance of the DLCMI. If no DLCMI is running, the Frame Relay
interface will stay in the running s… | column | Enumeration | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.11 |
| juniFrDlcmiRowStatus Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy
… | column | SNMPv2-TCRowStatus | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.12 |
| juniFrDlcmiLowerIfIndex The ifIndex of an interface over which this Frame Relay interface is to
be layered. A value of zero indicates no layering. An implementation
may choose to require that a nonzero… | column | IF-MIBInterfaceIndexOrZero | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.13 |
| juniFrDlcmiRole Specifies the role this interface assumes with respect to the remote
end.
When acting as a DTE, the following objects are not relevant:
juniFrDlcmiDcePollingInt… | column | Enumeration | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.14 |
| juniFrDlcmiDcePollingInterval The number of seconds within which a DCE expects to receive a Status
Enquiry from the DTE.
This value corresponds to the T392 timer.
Pertains to DCE/… | column | seconds Integer32 | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.15 |
| juniFrDlcmiDceErrorThreshold The minimum number of errors that must be observed within the number of
events specified by juniFrDlcmiDceMonitoredEvents, to declare the
interface down.
'error' is… | column | Integer32 | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.16 |
| juniFrDlcmiDceMonitoredEvents The number of DCE polling intervals over which accumulated errors are
counted against the threshold specified in juniFrDlcmiDceErrorThreshold.
If, within this numbe… | column | Integer32 | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.17 |
| juniFrDlcmiState This variable states which Data Link Connection Management scheme is
active (and by implication, what DLCI it uses) on the Frame Relay
interface. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.2 |
| juniFrDlcmiAddress This variable states which address format is in use on the Frame Relay
interface. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.3 |
| juniFrDlcmiAddressLen This variable states the address length in octets. In the case of Q922
format, the length indicates the entire length of the address including
the control portion. | column | Enumeration | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.4 |
| juniFrDlcmiPollingInterval This is the number of seconds between successive status enquiry
messages sent by the DTE.
Pertains to DTE/NNI operation only. This parameter can be reconfigured
on… | column | seconds Integer32 | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.5 |
| juniFrDlcmiFullEnquiryInterval Number of status enquiry intervals that pass before issuance of a full
status enquiry message.
Pertains to DTE/NNI operation only. This parameter can be reconfigur… | column | Integer32 | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.6 |
| juniFrDlcmiErrorThreshold The minimum number of errors that must be observed within the number of
events specified by juniFrDlcmiMonitoredEvents, to declare the interface
down.
'error' is la… | column | Integer32 | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.7 |
| juniFrDlcmiMonitoredEvents The number of status polling intervals over which the error threshold
is counted. For example, if within 'MonitoredEvents' number of events
the station receives 'ErrorThreshold' … | column | Integer32 | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.8 |
| juniFrDlcmiMaxSupportedVCs The maximum number of Virtual Circuits allowed for this interface.
Usually dictated by the Frame Relay network.
In response to a SET, if a value less than zero or h… | column | FRAME-RELAY-DTE-MIBDLCI | .1.3.6.1.4.1.4874.2.2.10.1.1.2.1.9 |