HUAWEI-ETHERNET-OPTICMODULE-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
9
Rows
9
Columns
199
.1.3.6.1.4.1.2011.5.14.6.1
·
1 row entry
·
41 columns
Indicates the optical module table of an Ethernet port. It is used for querying the information about the optical module of an Ethernet port. The index of this table is ifIndex.
Indicates the optical module table of an Ethernet port. It is used for querying
the information about the optical module of an Ethernet port.
The index of this entry is ifIndex.
the information about the optical module of an Ethernet port.
The index of this entry is ifIndex.
Indexes
IF-MIBifIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
hwOpticsMDIdentifier
Indicate the identifier of optical module.
Options: 1. unknown(1) -unknown the identifier of optical module 2. gbic(2) -the identifier of optical module is gbic 3. soldered… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.1 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDExtID
Indicate the extended type of optical module.
Options: 1. notSpecifiedOrNotCompliant(1) -the extended type of optical module is notSpecifiedOrNotCompliant 2. moddef1(2) -the extended type of opti… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.2 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDConnector
Indicate the type of optical module connector.
Options: 1. unknown(1) -unknown the type of optical module connector 2. sc(2) -the type of optical module connector is sc 3. copperConnec… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.3 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDEncoding
Indicate the encoding mechanism.
Options: 1. unspecified(1) -the encoding mechanism is unspecified 2. encodingMethod8B10B(2) -the encoding mechanism is encodingMethod8B10B 3. encodingMethod4B5B(3) -the… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.4 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDBrNominal
Nominal bit rate.
Unit: 100 MBits/sec |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.5 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDLength9Micronkm
Indicate the link length that is supported by the transceiver while operating in
compliance with the applicable standards using 9 micron Single-mode Fiber. The maximum value is 255, which means that the transceiver sup… |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.6 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDLength9Micron
Indicate the link length that is supported by the transceiver while operating in
compliance with the applicable standards using 9 micron Single-mode Fiber. The maximum value is 255, which means that the transceiver supp… |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.7 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDLength50Micron
Indicate link length that is supported by the transceiver while operating in
compliance with applicable standards using 50 micron multi-mode OM2 [500MHz*km] fiber. The maximum value is 255, which means that the transce… |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.8 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDLength62Micron5
Indicate link length that is supported by the transceiver while operating in
compliance with applicable standards using 62.5 micron multi-mode OM1 [200 MHz*km] fiber. The maximum value is 255, which means that the tran… |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.9 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDLengthCopper
Indicate Link length supported for copper.
Unit: 1m |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.10 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDVendorName
Indicate the vendor name of a optical module.
|
OctetString Constraints: range: 0-17 |
.1.3.6.1.4.1.2011.5.14.6.1.1.11 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDVendorOUI
Indicate the vendor IEEE company ID of a optical module.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.12 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDVendorPN
Indicate the part number of a optical module provided by vendor.
|
OctetString Constraints: range: 0-17 |
.1.3.6.1.4.1.2011.5.14.6.1.1.13 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDVendorRev
Indicate the revision level for part number provided by vendor.
|
OctetString Constraints: range: 0-5 |
.1.3.6.1.4.1.2011.5.14.6.1.1.14 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDWaveLength
The laser wavelength.
Unit: 1nm |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.15 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDCcBase
The check code for base ID fields(one byte).
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.16 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDOptions
Options:
1. rateSelect(1) -RATE_SELECT is implemented 2. txDisableAndTheSerialOutputDisabled(2) -TX_DISABLE is implemented and disables the serial output. 3. txFa… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.17 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDBrMax
The upper bit rate margin.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.18 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDBrMin
The lower bit rate margin.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.19 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDVendorSN
The serial number of a optical module provided by vendor.
|
OctetString Constraints: range: 0-17 |
.1.3.6.1.4.1.2011.5.14.6.1.1.20 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDDateCode
The date code of a optical module.
|
OctetString Constraints: range: 0-9 |
.1.3.6.1.4.1.2011.5.14.6.1.1.21 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDDiagnosticMonitoringType
Indicate the diagnostic monitoring type.
Options: 1. internallyCalibrated(1) -the diagnostic monitoring type is internallyCalibrated 2. externallyCalibrated(2) -the diagnostic monitoring type is externallyCalibrate… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.22 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDEnhancedOptions
Indicate enhanced Options.
Options: 1. forAllMonitoredQuantities(1) -optional Alarm/warning flags implemented for all monitored quantities 2. txDisable(2) -optional Soft TX_DISABLE control and monitoring… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.23 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDSFF8472Compliance
Indicate the SFF-8472 standard.
Options: 1. undefined(1) -not included or undefined. 2. includesSFF8472V93(2) -includes functionality described in SFF-8472 Rev 9.3. 3. includesSFF8472V95(3) -includes f… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.24 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDCcExt
Check code for the Extended ID Fields.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.25 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDVendorSpecific
Vendor of Optical module specific information.
|
OctetString Constraints: range: 0-96 |
.1.3.6.1.4.1.2011.5.14.6.1.1.26 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDCLEICode
CLEI code supported by eSFP. Length is 10 bytes.
|
OctetString Constraints: range: 0-10 |
.1.3.6.1.4.1.2011.5.14.6.1.1.27 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDInfoRemote
Indicates the operation is performed on a remote optical module.
Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.28 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDSFPPulsCableTech
Indicates the cable specification compliance.
Options: 1. passiveCable(1) -Passive Cable 2. activeCable(2) -Active Cable 2. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.29 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDSFPRateId
Indicates the cable specification compliance.
Options: 1. sff8079(1) -Defined for SFF-8079 (4/2/1G Rate_Select & AS0/AS1) 2. sff8431RX(2) -Defined for SFF-8431 (8/4/2G Rx Rate_Select only) 3. sff8431TX(3) … |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.30 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDLength50MicronOM3
Indicate link length that is supported by the transceiver while operating in
compliance with applicable standards using 50 micron multi-mode OM2 [2000MHz*km] fiber. The maximum value is 255, which means that the transc… |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.31 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsDwdmClass
Extended identifier: WDM class.
Options: 1. noWdm(1) -no WDM 2. cwdm(2) -CWDM 3. dwdm(3) -DWDM 4. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.32 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsDwdmPower
Extended identifier: Power level.
Options: 1. dwdmPowerLevel1(1) -The power is lower than 1W. 2. dwdmPowerLevel2(2) -The power is between 1W and 1.5W. 3. dwdmPowerLevel3(3) -The power is higher than 1.5W. 4. inval… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.33 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsDwdmMaxTemperature
Max temperature.
Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.000001C |
0.000001CSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.34 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsDwdmMinTemperature
Min temperature.
Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.000001C |
0.000001CSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.35 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsDwdmMaxSupplyCurrent
Max supply current.
Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.000001A |
0.000001ASNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.36 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsDwdmChannelSpacing
Fibre channel spacing.
Options: 1. channelSpacing200G(1) -The fibre channel spacing is 200GHz. 2. channelSpacing100G(2) -The fibre channel spacing is 100GHZ. 3. channelSpacing50G(3) -The… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.37 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsDwdmNumberOfChannels
Number of channels.
Invalid value: -1, returned if the optical module is unavailable or not supported. |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.38 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsDwdmWaveLength
Laser wavelength.
Invalid value: -1, returned if the optical module is unavailable or not supported. Unit: 0.01nm |
0.01nmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.1.1.39 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsModuleUserEeprom
Optics module user EEPROM information.
|
OctetString Constraints: range: 0-384 |
.1.3.6.1.4.1.2011.5.14.6.1.1.40 |
||||||||||||||||||||||||||||||||||||
|
hwOpticsMDSFF8636Compliance
Indicate the SFF-8636 standard.
Options: 1. undefined(1) -not included or undefined. 2. includesSFF8436V48OrEarlier(2) -includes functionality described in SFF-8436 Rev 4.8 or earlier. 3. inc… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.1.1.41 |
.1.3.6.1.4.1.2011.5.14.6.2
·
1 row entry
·
9 columns
This table used for querying the information about the optical transceiver of an Ethernet port. The index of this table is ifindex.
This table used for querying the information about the optical transceiver of an Ethernet port.
The index of this entry is ifindex.
The index of this entry is ifindex.
Indexes
IF-MIBifIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
hwOpticsMDInfinibandComplianceCodes
Infiniband transceiver type.
Options: 1. sx(1) -infiniband transceiver type is sx 2. lx(2) -infiniband transceiver type is lx 3. copperActive(3) -infiniband transceiver type is copperActive 4. co… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.2.1.1 |
||||||||||||||||||||||||||||||||||||||||||
|
hwOpticsMDSONETcomplianceCodes
SONET transceiver type.
Options: 1. oC48LongReach(1) -SONET transceiver type is oC48LongReach 2. oC48IntermediateReach(2) -SONET transceiver type is oC48IntermediateReach 3. oC48Shor… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.2.1.2 |
||||||||||||||||||||||||||||||||||||||||||
|
hwOpticsMDGEComplianceCodes
Ethernet transceiver type.
Options: 1. en1000BASET(1) -Ethernet transceiver type is 1000BASE-T 2. en1000BASECX(2) -Ethernet transceiver type is 1000BASE-CX 3. en1000BASELX(3) -Eth… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.2.1.3 |
||||||||||||||||||||||||||||||||||||||||||
|
hwOpticsMDLinkLength
Fibre Channel link length.
Options: 1. veryLongDistance(1) -fibre channel link length is veryLongDistance 2. shortDistance(2) -fibre channel link length is shortDistance 3. intermediateDistance(3) -fibre c… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.2.1.4 |
||||||||||||||||||||||||||||||||||||||||||
|
hwOpticsMDTransmitterTechnology
Fibre Channel transmitter technology.
Options: 1. longwaveLaser(1) -fibre channel transmitter technology is longwaveLaser 2. electricalInterenclosure(2) -fibre channel transmitter technology is electric… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.2.1.5 |
||||||||||||||||||||||||||||||||||||||||||
|
hwOpticsMDTransmissionMedia
Fibre Channel transmission media.
Options: 1. twinAxialPair(1) -fibre channel transmission media is twinAxialPair 2. shieldedTwistedPair(2) -fibre channel transmission media is shieldedTwistedPair 3. minia… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.2.1.6 |
||||||||||||||||||||||||||||||||||||||||||
|
hwOpticsMDSpeed
Fibre Channel speed.
Options: 1. speed400MBytesPerSec(1) -fibre channel speed is 400 MBits/s 2. speed200MBytesPerSec(2) -fibre channel speed is 200 MBits/s 3. speed100MBytesPerSec(3) -fibre channel speed is 1… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.2.1.7 |
||||||||||||||||||||||||||||||||||||||||||
|
hwOpticsMDTransceiverRemote
Indicates the operation is performed on a remote optical module.
Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.2.1.8 |
||||||||||||||||||||||||||||||||||||||||||
|
hwOpticsMDHuaweiPartNumber
Indicate the part number of a optical module provided by Huawei.
|
OctetString Constraints: range: 0-17 |
.1.3.6.1.4.1.2011.5.14.6.2.1.9 |
.1.3.6.1.4.1.2011.5.14.6.3
·
1 row entry
·
80 columns
Indicates the 10GE optical module information table of an Ethernet port. It is used for querying the information about the 10GE optical module of an Ethernet port. The index of this table is ifindex.
Indicates the 10GE optical module information table of an Ethernet port.
It is used for querying the information about the 10GE optical module of
an Ethernet port.
The index of this entry is ifindex.
It is used for querying the information about the 10GE optical module of
an Ethernet port.
The index of this entry is ifindex.
Indexes
IF-MIBifIndex
| Column | Syntax | OID | ||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
hw10GEOpticsMDIdentifier
Indicate the identifier of 10GE optical module.
Options: 1. unknown(0) -unknown identifier of 10GE optical module 2. gbic(1) -the identifier of 10GE opt… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.1 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDExtCLEICode
Extended identifier: CLEI
Options: 1. nonExtCLEICode(0) -no CLEI code present in Table 02h 2. extCLEICode(1) -CLEI code present in Table 02h 3. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.2 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDExtTXRefClock
Extended identifier: TX Ref Clock
Options: 1. nonExtTXRefClock(0) -tx Ref Clock Input Not Required 2. extTXRefClock(1) -tx Ref Clock Input Required 3. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.3 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDExtCDRFunc
Extended identifier: CDR function
Options: 1. nonExtCDRFunc(0) -no CDR version of XFP 2. extCDRFunc(1) -module with CDR function 3. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.4 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDExtPowerLevel
Extended identifier: Power Level
Options: 1. extPowerLevel1(0) -power Level 1 Module (1.5 W max. power dissipation.) 2. extPowerLevel2(1) -power Level 2 Module (2.5W Max) 3. extPowerLevel3(2) -power Level 3 Module… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.5 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDConnector
Indicate the type of 10GE optical module connector.
Options: 1. unknown(0) -unknown the type of 10GE optical module connector 2. sc(1) -the type of 10GE optical module connector is s… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.6 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEthComplianceBaseEW
Indicate 10GBASE-EW support or not.
Options: 1. nonEthComplianceBaseEW(0) -not support 10GBASE-EW 2. ethComplianceBaseEW(1) -support 10GBASE-EW |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.7 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEthComplianceBaseLW
Indicate 10GBASE-LW support or not.
Options: 1. nonEthComplianceBaseLW(0) -not support 10GBASE-LW 2. ethComplianceBaseLW(1) -support 10GBASE-LW |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.8 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEthComplianceBaseSW
Indicate 10GBASE-SW support or not.
Options: 1. nonEthComplianceBaseSW(0) -not support 10GBASE-SW 2. ethComplianceBaseSW(1) -support 10GBASE-SW |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.9 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEthComplianceBaseLRM
Indicate 10GBASE-LRM support or not.
Options: 1. nonEthComplianceBaseLRM(0) -not support 10GBASE-LRM 2. ethComplianceBaseLRM(1) -support 10GBASE-LRM |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.10 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEthComplianceBaseER
Indicate 10GBASE-ER support or not.
Options: 1. nonEthComplianceBaseER(0) -not support 10GBASE-ER 2. ethComplianceBaseER(1) -support 10GBASE-ER |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.11 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEthComplianceBaseLR
Indicate 10GBASE-LR support or not.
Options: 1. nonEthComplianceBaseLR(0) -not support 10GBASE-LR 2. ethComplianceBaseLR(1) -support 10GBASE-LR |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.12 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEthComplianceBaseSR
Indicate 10GBASE-SR support or not.
Options: 1. nonEthComplianceBaseSR(0) -not support 10GBASE-SR 2. ethComplianceBaseSR(1) -support 10GBASE-SR |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.13 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDFibreCompliance
Indicate 10 Gigabit Fibre Channel Compliance type.
Options: 1. fibreComplianceInter1300FP(16) -intermediate Reach 1300 nm FP 2. fibreComplianceExtended1550(32) -extended reach 1550 nm 3. fibreComplianceSM1200(64) … |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.14 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDLowerSpeedLink
Indicate Lower Speed Links type.
Options: 1. lowerSpeedLinkOC48LR(2) -lower speed links type is OC48LR 2. lowerSpeedLinkOC48IR(4) -lower speed links type is OC48IR 3. lowerSpeedLinkOC48SR(8) -lower speed links t… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.15 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesI64point5
Indicate SONET/SDH Codes I-64.5 support or not.
Options: 1. notSupport(0) -not Support I-64.5 2. support(1) -support I-64.5 |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.16 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesI64point3
Indicate SONET/SDH Codes I-64.3 support or not.
Options: 1. notSupport(0) -not Support I-64.3 2. support(1) -support I-64.3 |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.17 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesI64point2
Indicate SONET/SDH Codes I-64.2 support or not.
Options: 1. notSupport(0) -not Support I-64.2 2. support(1) -support I-64.2 |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.18 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesI64point2r
Indicate SONET/SDH Codes I-64.2r support or not.
Options: 1. notSupport(0) -not support I-64.2r 2. support(1) -support I-64.2r |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.19 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesI64point1
Indicate SONET/SDH Codes I-64.1 support or not.
Options: 1. notSupport(0) -not support I-64.1 2. support(1) -support I-64.1 |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.20 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesI64point1r
Indicate SONET/SDH Codes I-64.1r support or not.
Options: 1. notSupport(0) -not support I-64.1r 2. support(1) -support I-64.1r |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.21 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesS64point5b
Indicate SONET/SDH Codes S-64.5b support or not.
Options: 1. notSupport(0) -not support S-64.5b 2. support(1) -support S-64.5b |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.22 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesS64point5a
Indicate SONET/SDH Codes S-64.5a support or not.
Options: 1. notSupport(0) -not support S-64.5a 2. support(1) -support S-64.5a |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.23 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesS64point3b
Indicate SONET/SDH Codes S-64.3b support or not.
Options: 1. notSupport(0) -not support S-64.3b 2. support(1) -support S-64.3b |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.24 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesS64point3a
Indicate SONET/SDH Codes S-64.3a support or not.
Options: 1. notSupport(0) -not support S-64.3a 2. support(1) -support S-64.3a |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.25 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesS64point2b
Indicate SONET/SDH Codes S-64.2b support or not.
Options: 1. notSupport(0) -not support S-64.2b 2. support(1) -support S-64.2b |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.26 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesS64point2a
Indicate SONET/SDH Codes S-64.2a support or not.
Options: 1. notSupport(0) -not support S-64.2a 2. support(1) -support S-64.2a |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.27 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesS64point1
Indicate SONET/SDH Codes S-64.1 support or not.
Options: 1. notSupport(0) -not support S-64.1 2. support(1) -support S-64.1 |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.28 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesG959P1L1
Indicate SONET/SDH Codes G.959.1 P1L1-2D2 support or not.
Options: 1. notSupport(0) -not support G.959.1 P1L1-2D2 2. support(1) -support G.959.1 P1L1-2D2 |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.29 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesL64point3
Indicate SONET/SDH Codes L-64.3 support or not.
Options: 1. notSupport(0) -not support L-64.3 2. support(1) -support L-64.3 |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.30 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesL64point2c
Indicate SONET/SDH Codes L-64.2c support or not.
Options: 1. notSupport(0) -not support L-64.2c 2. support(1) -support L-64.2c |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.31 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesL64point2b
Indicate SONET/SDH Codes L-64.2b support or not.
Options: 1. notSupport(0) -not support L-64.2b 2. support(1) -support L-64.2b |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.32 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesL64point2a
Indicate SONET/SDH Codes L-64.2a support or not.
Options: 1. notSupport(0) -not support L-64.2a 2. support(1) -support L-64.2a |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.33 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesL64point1
Indicate SONET/SDH Codes L-64.1 support or not.
Options: 1. notSupport(0) -not support L-64.1 2. support(1) -support L-64.1 |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.34 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesV64point3
Indicate SONET/SDH Codes V-64.3 support or not.
Options: 1. notSupport(0) -not support V-64.3 2. support(1) -support V-64.3 |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.35 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesV64point2b
Indicate SONET/SDH Codes V-64.2b support or not.
Options: 1. notSupport(0) -not support V-64.2b 2. support(1) -support V-64.2b |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.36 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSONETSDHCodesV64point2a
Indicate SONET/SDH Codes V-64.2a support or not.
Options: 1. notSupport(0) -not support V-64.2a 2. support(1) -support V-64.2a |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.37 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEncodingRZ
Indicate encoding mechanism RZ support or not.
Options: 1. nonEncodingRZ(0) -not support RZ 2. encodingRZ(1) -support RZ |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.38 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEncodingNRZ
Indicate encoding mechanism NRZ support or not.
Options: 1. nonEncodingNRZ(0) -not support NRZ 2. encodingNRZ(1) -support NRZ |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.39 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEncodingSONET
Indicate encoding mechanism SONET support or not.
Options: 1. nonEncodingSONET(0) -not support SONET 2. encodingSONET(1) -support SONET |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.40 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEncoding8B10B
Indicate encoding mechanism 8B10B support or not.
Options: 1. nonEncoding8B10B(0) -not support 8B10B 2. encoding8B10B(1) -support 8B10B |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.41 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEncoding64B
Indicate encoding mechanism 64B/66B support or not.
Options: 1. nonEncoding64B(0) -not support 64B/66B 2. encoding64B(1) -support 64B/66B |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.42 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDBrMin
Minimum bit rate.
Unit: 100 MBits/s |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.43 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDBrMax
Maximum bit rate.
Unit: 100 MBits/s |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.44 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSupportLenSMF
Indicate the link length that is supported by the transceiver with the applicable standards
using Single-mode Fiber. |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.45 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSupportLenE50um
Indicate the link length that is supported by the transceiver with the applicable standards
using 2000MHz*km (850nm) extended bandwidth 50 micron core multimode fiber. Unit: 2m |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.46 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSupportLen50um
This value specifies the link length that is supported by the transceiver with the applicable
standards using 500MHz*km (850 and 1310nm) 50 micron core multimode fiber. Unit: 1m |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.47 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSupportLen62p5um
This value specifies the link length that is supported by the transceiver with the applicable
standards using 200MHz*km (850 nm)/500 MHz*km (1310 nm) 62.5 micron core multimode fiber. Unit: 1m |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.48 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSupportLenCopper
Indicate the minimum link length that is supported by the transceiver with copper cable.
Unit: 1m |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.49 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDTransmitterSupport
Indicate the transmitter support tunable or not.
Options: 1. nonTunable(0) -transmitter not support tunable 2. tunable(1) -transmitter support tunable 3. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.50 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDDetector
Indicate the Detector is enable or not.
Options: 1. nonDetector(0) -detector is disable 2. detector(1) -detector is enable 3. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.51 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDCooledTransmitterDevice
Indicate the Cooled transmitter is enable or not.
Options: 1. nonSupport(0) -cooled transmitter is disable 2. support(1) -cooled transmitter is enable 3. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.52 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDWavelengthControl
Indicate the wavelength control support or not.
Options: 1. nonSupport(0) -wavelength control not support 2. support(1) -wavelength control support 3. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.53 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDTransmitterTechnologySupport
Indicate the transmitter technology type.
Options: 1. vCSEL850(0) -the transmitter technology type is vCSEL850 2. vCSEL1310(1) -the transmitter technology type is vCSEL1310 3. vCSEL1550(2) -the transmitter tec… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.54 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDVendorName
Indicate the vendor name of a 10GE optical module.
|
OctetString Constraints: range: 0-40 |
.1.3.6.1.4.1.2011.5.14.6.3.1.55 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSupportXFIMode
Indicate the XFI loopback mode support or not.
Options: 1. nonSupportXFIMode(0) -the XFI loopback mode not support 2. supportXFIMode(1) -the XFI loopback mode support 3. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.56 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDSupportLinesideMode
Indicate the Lineside loopback mode support or not.
Options: 1. nonSupportLinesideMode(0) -lineside loopback mode not support 2. supportLinesideMode(1) -lineside loopback mode support 3. invalid(-1) -invalid va… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.57 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDMaxBitRateSupportedByCDR
Indicate which rate is supported by the CDR.
Options: 1. maxBitRateSupportedByCDR11p1(1) -CDR support for 11.1 Gb/s 2. maxBitRateSupportedByCDR10p7(3) -CDR support for 10.7 Gb/s 3. maxBitRateSupportedByCDR10p5(7) -C… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.58 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDVendorOUI
Indicate the vendor IEEE company ID of a 10GE optical module.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.59 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDVendorPN
Indicate the part number of a 10GE optical module provided by vendor.
|
OctetString Constraints: range: 0-40 |
.1.3.6.1.4.1.2011.5.14.6.3.1.60 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDVendorRev
Indicate the revision level for part number provided by vendor.
|
OctetString Constraints: range: 0-40 |
.1.3.6.1.4.1.2011.5.14.6.3.1.61 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDWavelength
The laser wavelength.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.62 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDWaveTolerance
The guaranteed +/- range of transmitter output wavelength under all normal operating conditions.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.63 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDMaxCaseTemperature
Maximum Case Temperature in Degrees C.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.64 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDCcbase
Cc_base.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.65 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDMaxDissipation
Maximum Power Dissipation.
Max power is 8 bit value * 20 mW. |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.66 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDMaxDissipationPowerDownMode
Maximum Total Power Dissipation in Power Down Mode.
Max Power is 8 bit value * 10 mW. |
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.67 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDMaximum5P0VSupply
Maximum current required by +5V Supply.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.68 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDMaximum3P3VSupply
Maximum current required by +3.3V Supply.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.69 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDMaximum1P8VSupply
Maximum current required by +1.8V Supply.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.70 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDMaximum5P2VSupply
Maximum current required by -5.2V Supply.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.71 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDVendorSN
The serial number of a 10GE optical module provided by vendor.
|
OctetString Constraints: range: 0-140 |
.1.3.6.1.4.1.2011.5.14.6.3.1.72 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDDateCode
The date code of a 10GE optical module.
|
OctetString Constraints: range: 0-40 |
.1.3.6.1.4.1.2011.5.14.6.3.1.73 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDDiagnoMonitorPowerMeasure
Received power measurement type.
Options: 1. supportOMA(0) -OMA 2. supportAveragePower(1) -AveragePower |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.74 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDDiagnoMonitorTypeFECBER
Module Respond to FEC BER.
Options: 1. nonSupportBER(0) -no BER Support 2. supportBER(1) -BER Support |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.75 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDEnhancedOptions
Indicate enhanced Options.
Options: 1. cmu(0) -enhanced options is cmu 2. rateSelect(2) -enhanced options is rateSelect 3. fec(4) -enhanced options is fec 4. vpsby(8) -enhanced options… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.76 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDAuxInputOne
Indicate which quantity is monitored by each auxiliary A/D channel one.
Options: 1. auxInputType1(0) -Auxiliary monitoring not implemented 2. auxInputType2(1) -APD Bias Voltage 3. auxInputType4(3) -TE… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.77 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDAuxInputTwo
Indicate which quantity is monitored by each auxiliary A/D channel two.
Options: 1. auxInputType1(0) -Auxiliary monitoring not implemented 2. auxInputType2(1) -APD Bias Voltage 3. auxInputType4(3) -T… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.3.1.78 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDCCEXT
CC_EXT
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.3.1.79 |
||||||||||||||||||||||||||||||
|
hw10GEOpticsMDVendorSpecific
Vendor of 10GE Optical module specific information.
|
OctetString Constraints: range: 0-140 |
.1.3.6.1.4.1.2011.5.14.6.3.1.80 |
.1.3.6.1.4.1.2011.5.14.6.4
·
1 row entry
·
9 columns
Indicates the optical module diagnose information table of an Ethernet port. It is used for querying the diagnose information about the optical module of an Ethernet port. The index of this table is ifindex.
Indicates the optical module diagnose information table of an Ethernet port.
It is used for querying the diagnose information about the optical module of
an Ethernet port.
The index of this entry is ifindex.
It is used for querying the diagnose information about the optical module of
an Ethernet port.
The index of this entry is ifindex.
Indexes
IF-MIBifIndex
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
|
hwOpticsTemperature
Temperature.
Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001C |
0.000001CSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.4.1.1 |
||||
|
hwOpticsSupplyVoltage
Supply voltage.
Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001V |
0.000001VSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.4.1.2 |
||||
|
hwOpticsTxBiasCurrent
Transmitted bias current.
Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001mA |
0.000001mASNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.4.1.3 |
||||
|
hwOpticsTxPower
Transmitted power.
Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001dBm |
0.000001dBmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.4.1.4 |
||||
|
hwOpticsRxPower
Received power.
Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001dBm |
0.000001dBmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.4.1.5 |
||||
|
hwOpticsMDDdmInfoRemote
Indicates the operation is performed on a remote optical module.
Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.4.1.6 |
||||
|
hwOpticsLaserTemperature
Temperature of the optical laser.
Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.000001C |
0.000001CSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.4.1.7 |
||||
|
hwOpticsWaveLength
Wavelength of the optical laser.
Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.01nm |
0.01nmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.4.1.8 |
||||
|
hwOpticsTecCurrent
Current of the thermoelectric cooler on the optical module.
Invalid value: 2147483647, returned if the optical module is unavailable or not supported. Unit: 0.000001A |
0.000001ASNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.4.1.9 |
.1.3.6.1.4.1.2011.5.14.6.5
·
1 row entry
·
23 columns
Indicates the optical power threshold table of an Ethernet port. It is used for querying, setting, and clearing the optical power threshold of an Ethernet port. After the power threshold is set, the power threshold alarming function of the optical port is enabled. When the optical power is lower than the lower threshold or higher than the upper threshold, an alarm is reported. The index of this table is ifindex.
Indicates the optical power threshold table of an Ethernet port.
It is used for querying, setting, and clearing the optical power threshold of an Ethernet port.
After the power threshold is set, the power threshold alar…
It is used for querying, setting, and clearing the optical power threshold of an Ethernet port.
After the power threshold is set, the power threshold alar…
Indexes
IF-MIBifIndex
| Column | Syntax | OID | ||||||
|---|---|---|---|---|---|---|---|---|
|
hwOpticsPowerTxLowerThresholdValue
TX optical power lower limit threshold value.
Options: 1. -99000000..100000000 -valid range of optical power lower limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection t… |
0.000001dBmInteger32r/w Constraints: range: -99000000-100000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.1 |
||||||
|
hwOpticsPowerThresholdSwitch
Optical power threshold value Switch.
Options: 1. on(1) -set optical power threshold value 2. off(2) -clear optical power threshold value 3. invalid(-1) -invalid value Default: off(2) |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.5.1.2 |
||||||
|
hwOpticsPowerTxUpperThresholdValue
TX optical power upper limit threshold value.
1. -99000000..100000000 -valid range of optical power upper limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection threshold.… |
0.000001dBmInteger32r/w Constraints: range: -99000000-100000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.3 |
||||||
|
hwOpticsPowerRxUpperThresholdValue
RX optical power upper limit threshold value.
1. -99000000..100000000 -valid range of optical power upper limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection threshold.… |
0.000001dBmInteger32r/w Constraints: range: -99000000-100000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.4 |
||||||
|
hwOpticsPowerRxLowerThresholdValue
RX optical power lower limit threshold value.
1. -99000000..100000000 -valid range of optical power lower limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection threshold.… |
0.000001dBmInteger32r/w Constraints: range: -99000000-100000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.5 |
||||||
|
hwOpticsTemperatureLowerThresholdValue
Optical temperature lower limit threshold value.
1. -99000000..300000000 -valid range of optical temperature lower limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection t… |
0.000001CInteger32r/w Constraints: range: -99000000-300000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.6 |
||||||
|
hwOpticsTemperatureUpperThresholdValue
Optical temperature upper limit threshold value.
1. -99000000..300000000 -valid range of optical temperature upper limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection t… |
0.000001CInteger32r/w Constraints: range: 2147483646-2147483647range: -99000000-300000000 |
.1.3.6.1.4.1.2011.5.14.6.5.1.7 |
||||||
|
hwOpticsTemperatureThresholdSwitch
Optical temperature threshold value Switch.
Options: 1. on(1) -set optical temparature threshold value 2. off(2) -clear optical temperature threshold value 3. invalid(-1) -invalid value Default: off(2) |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.5.1.8 |
||||||
|
hwOpticsVoltageLowerThresholdValue
Optical voltage lower limit threshold value.
1. 0..100000000 -valid range of optical voltage lower limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection threshold… |
0.000001VInteger32r/w Constraints: range: 0-100000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.9 |
||||||
|
hwOpticsVoltageUpperThresholdValue
Optical voltage upper limit threshold value.
1. 0..100000000 -valid range of optical voltage upper limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection threshold… |
0.000001VInteger32r/w Constraints: range: 0-100000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.10 |
||||||
|
hwOpticsVoltageThresholdSwitch
Optical voltage threshold value Switch.
Options: 1. on(1) -set optical voltage threshold value 2. off(2) -clear optical voltage threshold value 3. invalid(-1) -invalid value Default: off(2) |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.5.1.11 |
||||||
|
hwOpticsCurrentLowerThresholdValue
Optical current lower limit threshold value.
1. 0..10000000 -valid range of optical current lower limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection threshold… |
0.000001AInteger32r/w Constraints: range: 0-10000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.12 |
||||||
|
hwOpticsCurrentUpperThresholdValue
Optical current upper limit threshold value.
1. 0..10000000 -valid range of optical current upper limit threshold value. 2. 2147483646 -indication the optical module built-in alarm detection threshold… |
0.000001AInteger32r/w Constraints: range: 0-10000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.13 |
||||||
|
hwOpticsCurrentThresholdSwitch
Optical current threshold value Switch.
Options: 1. on(1) -set optical current threshold value 2. off(2) -clear optical current threshold value 3. invalid(-1) -invalid value Default: off(2) |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.5.1.14 |
||||||
|
hwOpticsLaserTemperatureLowerThresholdValue
Lower optical laser temperature threshold.
1. -99000000..300000000 -valid range of the lower optical laser temperature threshold. 2. 2147483646 -indication the optical module built-in alarm detection threshold… |
0.000001CInteger32r/w Constraints: range: -99000000-300000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.15 |
||||||
|
hwOpticsLaserTemperatureUpperThresholdValue
Upper optical laser temperature threshold.
1. -99000000..300000000 -valid range of the upper optical laser temperature threshold. 2. 2147483646 -indication the optical module built-in alarm detection threshold… |
0.000001CInteger32r/w Constraints: range: -99000000-300000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.16 |
||||||
|
hwOpticsLaserTemperatureThresholdSwitch
Switch of optical laser temperature thresholds.
Options: 1. on(1) -Set optical laser temperature thresholds. 2. off(2) -Clear optical laser temperature thresholds. 3. invalid(-1) -invalid value Default: off(2) |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.5.1.17 |
||||||
|
hwOpticsWaveLengthLowerThresholdValue
Lower optical laser wavelength threshold.
1. 100000..165600 -valid range of the lower optical laser wavelength threshold. 2. 2147483646 -indication the optical module built-in alarm detection threshold. 3. 214748364… |
0.01nmInteger32r/w Constraints: range: 100000-165600range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.18 |
||||||
|
hwOpticsWaveLengthUpperThresholdValue
Upper optical laser wavelength threshold.
1. 100000..165600 -valid range of the upper optical laser wavelength threshold. 2. 2147483646 -indication the optical module built-in alarm detection threshold. 3. 214748364… |
0.01nmInteger32r/w Constraints: range: 100000-165600range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.19 |
||||||
|
hwOpticsWaveLengthThresholdSwitch
Switch of optical laser wavelength thresholds.
Options: 1. on(1) -Set optical laser wavelength thresholds. 2. off(2) -Clear optical laser wavelength thresholds. 3. invalid(-1) -invalid value Default: off(2) |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.5.1.20 |
||||||
|
hwOpticsTecCurrentLowerThresholdValue
Lower threshold for the thermoelectric cooler current.
1. -10000000-10000000 -valid range of the lower threshold for the thermoelectric cooler current. 2. 2147483646 -indication the optical module built-in alarm… |
0.000001AInteger32r/w Constraints: range: -10000000-10000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.21 |
||||||
|
hwOpticsTecCurrentUpperThresholdValue
Upper threshold for the thermoelectric cooler current.
1. -10000000-10000000 -valid range of the upper threshold for the thermoelectric cooler current. 2. 2147483646 -indication the optical module built-in alarm… |
0.000001AInteger32r/w Constraints: range: -10000000-10000000range: 2147483646-2147483647 |
.1.3.6.1.4.1.2011.5.14.6.5.1.22 |
||||||
|
hwOpticsTecCurrentThresholdSwitch
Switch of thermoelectric cooler current thresholds.
Options: 1. on(1) -Set thermoelectric cooler current thresholds. 2. off(2) -Clear thermoelectric cooler current thresholds. 3. invalid(-1) -invalid value De… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.5.1.23 |
.1.3.6.1.4.1.2011.5.14.6.7
·
1 row entry
·
16 columns
Indicates the extended information table of a smart SFP optical module. It is used for querying the extend information about a smart SFP optical module and setting loopback of a smart SFP optical module. This operation can be performed on both local and remote optical modules. When this operation is performed on a remote optical module, the hwOpticsSmartSFPExtModuleInfoRemote leaf is required. The index of this table is ifIndex.
Indicates the extended information table of a smart SFP optical module.
It is used for querying the extend information about a smart SFP optical module and setting loopback of a smart SFP optical module.
This operation …
It is used for querying the extend information about a smart SFP optical module and setting loopback of a smart SFP optical module.
This operation …
Indexes
IF-MIBifIndex
| Column | Syntax | OID | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
hwOpticsSmartSFPIdentifier
Indicates the type of a smart SFP optical module.
Options: 1. smartSFPI(1) -The optical module is a smart SFP I optical module 2. smartSFPII(2) -The optical module is a smart SFP II optical module… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.1 |
||||||||
|
hwOpticsSmartSFPProtocolVersion
Indicates the protocol version of a smart SFP optical module.
Range: -1, 0-255. -1 is the invalid value. |
Integer32 Constraints: range: -1-255 |
.1.3.6.1.4.1.2011.5.14.6.7.1.2 |
||||||||
|
hwOpticsSmartSFPSSFPEnhancedOption
Indicates the enhanced options of a smart SFP optical module.
Range: -1, 0-65535. -1 is the invalid value. |
Integer32 Constraints: range: -1-65535 |
.1.3.6.1.4.1.2011.5.14.6.7.1.3 |
||||||||
|
hwOpticsSmartSFPPassword
Indicates the password of a smart SFP optical module.
|
SNMPv2-SMIUnsigned32 Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32Type Constraints: range: 0..4294967295 |
.1.3.6.1.4.1.2011.5.14.6.7.1.4 |
||||||||
|
hwOpticsSmartSFPRemoteControllable
Indicates whether the remote smart SFP optical module can control the local optical module.
Options: 1. disable(1) -disable, control command from remote optical module will be ignored 2. enable(2) -enable 3… |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.5 |
||||||||
|
hwOpticsSmartSFPSubCarrierControl
Indicates sub-carrier control of a smart SFP optical module, that is,
whether the local smart SFP optical module can send signals to the remote optical module. Options: 1. disable(1) -disable 2. enable(2) … |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.6 |
||||||||
|
hwOpticsSmartSFPSubCarrierlinkStatus
Indicates the sub-carrier status of a smart SFP optical module.
Options: 1. down(1) -linked down 2. rxUp(2) -linked up in RX only 3. up(3) -linked up in both RX and TX direction 4. invalid(-1) … |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.7 |
||||||||
|
hwOpticsSmartSFPLocalLoopback
Indicates the loopback control of a local smart SFP optical module.
Options: 1. noloop(1) -no loop 2. remote(2) -local outward loop back 3. local(3) -local inward loop back 4. invalid(-1) -invalid val… |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.8 |
||||||||
|
hwOpticsSmartSFPRemoteLoopback
Indicates the loopback control of a remote smart SFP optical module.
Options: 1. noloop(1) -no loop 2. remote(2) -remote outward loop back 3. invalid(-1) -invalid value |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.9 |
||||||||
|
hwOpticsSmartSFPDyingGaspStatus
Indicates the dying-gasp status of a remote smart SFP optical module.
Options: 1. poweron(1) -remote normal power 2. poweroff(2) -remote Dying-Gasp asserted 3. invalid(-1) -invalid value |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.10 |
||||||||
|
hwOpticsSmartSFPLocalRXOutputControl
Indicates the local output control of a smart SFP optical module.
Options: 1. disable(1) -disable 2. enable(2) -enable 3. disableRxLos(3) -disable when LOS asserted 4. invalid(-1) -invalid value |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.11 |
||||||||
|
hwOpticsSmartSFPPilottoneControl
Indicates control of outputting attenuation signals by a smart SFP optical module.
Options: 1. disable(1) -disable 2. enable(2) -enable 3. invalid(-1) -invalid value |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.12 |
||||||||
|
hwOpticsSmartSFPPilottoneStatus
Indicates the carrier loopback detection status of a smart SFP optical module.
Options: 1. noSignal(1) -no signal 2. toneDetected(2) -tone detected 3. invalid(-1) -invalid value |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.13 |
||||||||
|
hwOpticsSmartSFPLoopbackdeviceloss
Indicates the optical attenuation of a remote loopback device.
Range: -1, 0-25500. -1 is the invalid value. Unit: 0.01db |
0.01dbInteger32 Constraints: range: -1-25500 |
.1.3.6.1.4.1.2011.5.14.6.7.1.14 |
||||||||
|
hwOpticsSmartSFPRoundtripfiberloss
Indicates the optical attenuation of an optical path.
Range: -1, 0-25500. -1 is the invalid value. Unit: 0.01db |
0.01dbInteger32 Constraints: range: -1-25500 |
.1.3.6.1.4.1.2011.5.14.6.7.1.15 |
||||||||
|
hwOpticsSmartSFPExtModuleInfoRemote
Indicates the operation is performed on a remote optical module.
Options: 1. remote(1) -the operation is performed on a remote optical module 2. invalid(-1) -invalid value |
Enumeration Enumerated Values:
|
.1.3.6.1.4.1.2011.5.14.6.7.1.16 |
.1.3.6.1.4.1.2011.5.14.6.8
·
1 row entry
·
1 columns
Indicates the configured parameter table of a smart SFP optical module. It is used for querying and setting the configured parameters of a smart SFP optical module. This table supports only the smart SFP 2 optical module. The index of this table is ifIndex.
Indicates the configured parameter table of a smart SFP optical module.
It is used for querying and setting the configured parameters of a smart SFP optical module.
This table supports only the smart SFP 2 optical modul…
It is used for querying and setting the configured parameters of a smart SFP optical module.
This table supports only the smart SFP 2 optical modul…
Indexes
IF-MIBifIndex
| Column | Syntax | OID |
|---|---|---|
|
hwOpticsSmartSFPIILoopOpticloss
Indicates the optical attenuation of a remote loopback device.
Unit: 0.01db. Range: -1, 0-25500. -1 is the invalid value. Default: 1400. |
0.01dbInteger32r/w Constraints: range: -1-25500 |
.1.3.6.1.4.1.2011.5.14.6.8.1.1 |
.1.3.6.1.4.1.2011.5.14.6.9
·
1 row entry
·
16 columns
It is used for querying the default value of optical power and parameter threshold of an Ethernet port. The index of this table is ifindex.
It is used for querying the default value of optical power and parameter
threshold of an Ethernet port.
The index of this entry is ifindex.
threshold of an Ethernet port.
The index of this entry is ifindex.
Indexes
IF-MIBifIndex
| Column | Syntax | OID |
|---|---|---|
|
hwOpticsModuleThresholdTxLower
TX optical power lower limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001dBm |
0.000001dBmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.1 |
|
hwOpticsModuleThresholdTxUpper
TX optical power upper limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001dBm |
0.000001dBmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.2 |
|
hwOpticsModuleThresholdRxUpper
RX optical power upper limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001dBm |
0.000001dBmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.3 |
|
hwOpticsModuleThresholdRxLower
RX optical power lower limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001dBm |
0.000001dBmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.4 |
|
hwOpticsModuleThresholdTempLower
Optical temperature lower limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001C |
0.000001CSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.5 |
|
hwOpticsModuleThresholdTempUpper
Optical temperature upper limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001C |
0.000001CSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.6 |
|
hwOpticsModuleThresholdVoltageLower
Optical voltage lower limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001V |
0.000001VSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.7 |
|
hwOpticsModuleThresholdVoltageUpper
Optical voltage upper limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001V |
0.000001VSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.8 |
|
hwOpticsModuleThresholdCurrentLower
Optical current lower limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001A |
0.000001ASNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.9 |
|
hwOpticsModuleThresholdCurrentUpper
Optical current upper limit threshold value.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001A |
0.000001ASNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.10 |
|
hwOpticsModuleThresholdLaserTempLower
Lower optical laser temperature threshold.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001C |
0.000001CSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.11 |
|
hwOpticsModuleThresholdLaserTempUpper
Upper optical laser temperature threshold.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001C |
0.000001CSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.12 |
|
hwOpticsModuleThresholdWaveLengthLower
Lower optical laser wavelength threshold.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.01nm |
0.01nmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.13 |
|
hwOpticsModuleThresholdWaveLengthUpper
Upper optical laser wavelength threshold.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.01nm |
0.01nmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.14 |
|
hwOpticsModuleThresholdTecCurrentLower
Lower threshold for the thermoelectric cooler current.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001A |
0.000001ASNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.15 |
|
hwOpticsModuleThresholdTecCurrentUpper
Upper threshold for the thermoelectric cooler current.
1. 2147483647 -invalid value, an invalid value is returned if the threshold is not exist. Unit: 0.000001A |
0.000001ASNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.9.1.16 |
.1.3.6.1.4.1.2011.5.14.6.10
·
1 row entry
·
4 columns
It is used for querying the optical module channel Ddm Information of an Ethernet port. The index of this table are ifIndex and hwOpticsModuleChannelIndex.
It is used for querying the optical module channel Ddm Information of an Ethernet port.
The index of this table are ifindex and hwOpticsModuleChannelIndex.
The index of this table are ifindex and hwOpticsModuleChannelIndex.
Indexes
IF-MIBifIndex hwOpticsModuleChannelIndex
| Column | Syntax | OID |
|---|---|---|
|
hwOpticsModuleChannelIndex
Optical module channel Index. 1~4 for 100G optical module.
|
SNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.10.1.1 |
|
hwOpticsModuleChannleTxBiasCurrent
Transmitted bias current.
Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001mA |
0.000001mASNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.10.1.2 |
|
hwOpticsModuleChannleTxPower
Transmitted power.
Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001dBm |
0.000001dBmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.10.1.3 |
|
hwOpticsModuleChannleRxPower
Received power.
Invalid value: 2147483647, an invalid value is returned if the optical module is unavailable or is not supported. Unit: 0.000001dBm |
0.000001dBmSNMPv2-SMIInteger32 Textual Convention: SNMPv2-SMIInteger32 Integer32Type Constraints: range: -2147483648..2147483647 |
.1.3.6.1.4.1.2011.5.14.6.10.1.4 |