hw10GEOpticsMDVendorSpecific
HUAWEI-ETHERNET-OPTICMODULE-MIB ·
.1.3.6.1.4.1.2011.5.14.6.3.1.80
Object
column
OctetString
Vendor of 10GE Optical module specific information.
Context
- MIB
- HUAWEI-ETHERNET-OPTICMODULE-MIB
- OID
.1.3.6.1.4.1.2011.5.14.6.3.1.80- Type
- column
- Access
- readonly
- Status
- current
- Parent
- hw10GEOpticsModuleInformationEntry
- Table
- hw10GEOpticsModuleInformationTable
- Siblings
- 79
Syntax
OctetString
Values & Constraints
Object Constraints
range: 0-140
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| hw10GEOpticsMDIdentifier Indicate the identifier of 10GE optical module.
Options:
1. unknown(0) -unknown identifier of 10GE optical module
2. gbic(1) … | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.1 |
| hw10GEOpticsMDEthComplianceBaseLRM Indicate 10GBASE-LRM support or not.
Options:
1. nonEthComplianceBaseLRM(0) -not support 10GBASE-LRM
2. ethComplianceBaseLRM(1) -support 10GBASE-LRM | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.10 |
| hw10GEOpticsMDEthComplianceBaseER Indicate 10GBASE-ER support or not.
Options:
1. nonEthComplianceBaseER(0) -not support 10GBASE-ER
2. ethComplianceBaseER(1) -support 10GBASE-ER | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.11 |
| hw10GEOpticsMDEthComplianceBaseLR Indicate 10GBASE-LR support or not.
Options:
1. nonEthComplianceBaseLR(0) -not support 10GBASE-LR
2. ethComplianceBaseLR(1) -support 10GBASE-LR | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.12 |
| hw10GEOpticsMDEthComplianceBaseSR Indicate 10GBASE-SR support or not.
Options:
1. nonEthComplianceBaseSR(0) -not support 10GBASE-SR
2. ethComplianceBaseSR(1) -support 10GBASE-SR | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.13 |
| hw10GEOpticsMDFibreCompliance Indicate 10 Gigabit Fibre Channel Compliance type.
Options:
1. fibreComplianceInter1300FP(16) -intermediate Reach 1300 nm FP
2. fibreComplianceExtended1550(32) -extended reach… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.14 |
| hw10GEOpticsMDLowerSpeedLink Indicate Lower Speed Links type.
Options:
1. lowerSpeedLinkOC48LR(2) -lower speed links type is OC48LR
2. lowerSpeedLinkOC48IR(4) -lower speed links type is OC48IR
3. lowerS… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.15 |
| hw10GEOpticsMDSONETSDHCodesI64point5 Indicate SONET/SDH Codes I-64.5 support or not.
Options:
1. notSupport(0) -not Support I-64.5
2. support(1) -support I-64.5 | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.16 |
| hw10GEOpticsMDSONETSDHCodesI64point3 Indicate SONET/SDH Codes I-64.3 support or not.
Options:
1. notSupport(0) -not Support I-64.3
2. support(1) -support I-64.3 | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.17 |
| hw10GEOpticsMDSONETSDHCodesI64point2 Indicate SONET/SDH Codes I-64.2 support or not.
Options:
1. notSupport(0) -not Support I-64.2
2. support(1) -support I-64.2 | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.18 |
| hw10GEOpticsMDSONETSDHCodesI64point2r Indicate SONET/SDH Codes I-64.2r support or not.
Options:
1. notSupport(0) -not support I-64.2r
2. support(1) -support I-64.2r | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.19 |
| hw10GEOpticsMDExtCLEICode Extended identifier: CLEI
Options:
1. nonExtCLEICode(0) -no CLEI code present in Table 02h
2. extCLEICode(1) -CLEI code present in Table 02h
3. invalid(-1) -invalid … | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.2 |
| hw10GEOpticsMDSONETSDHCodesI64point1 Indicate SONET/SDH Codes I-64.1 support or not.
Options:
1. notSupport(0) -not support I-64.1
2. support(1) -support I-64.1 | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.20 |
| hw10GEOpticsMDSONETSDHCodesI64point1r Indicate SONET/SDH Codes I-64.1r support or not.
Options:
1. notSupport(0) -not support I-64.1r
2. support(1) -support I-64.1r | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.21 |
| hw10GEOpticsMDSONETSDHCodesS64point5b Indicate SONET/SDH Codes S-64.5b support or not.
Options:
1. notSupport(0) -not support S-64.5b
2. support(1) -support S-64.5b | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.22 |
| hw10GEOpticsMDSONETSDHCodesS64point5a Indicate SONET/SDH Codes S-64.5a support or not.
Options:
1. notSupport(0) -not support S-64.5a
2. support(1) -support S-64.5a | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.23 |
| hw10GEOpticsMDSONETSDHCodesS64point3b Indicate SONET/SDH Codes S-64.3b support or not.
Options:
1. notSupport(0) -not support S-64.3b
2. support(1) -support S-64.3b | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.24 |
| hw10GEOpticsMDSONETSDHCodesS64point3a Indicate SONET/SDH Codes S-64.3a support or not.
Options:
1. notSupport(0) -not support S-64.3a
2. support(1) -support S-64.3a | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.25 |
| hw10GEOpticsMDSONETSDHCodesS64point2b Indicate SONET/SDH Codes S-64.2b support or not.
Options:
1. notSupport(0) -not support S-64.2b
2. support(1) -support S-64.2b | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.26 |
| hw10GEOpticsMDSONETSDHCodesS64point2a Indicate SONET/SDH Codes S-64.2a support or not.
Options:
1. notSupport(0) -not support S-64.2a
2. support(1) -support S-64.2a | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.27 |
| hw10GEOpticsMDSONETSDHCodesS64point1 Indicate SONET/SDH Codes S-64.1 support or not.
Options:
1. notSupport(0) -not support S-64.1
2. support(1) -support S-64.1 | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.28 |
| hw10GEOpticsMDSONETSDHCodesG959P1L1 Indicate SONET/SDH Codes G.959.1 P1L1-2D2 support or not.
Options:
1. notSupport(0) -not support G.959.1 P1L1-2D2
2. support(1) -support G.959.1 P1L1-2D2 | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.29 |
| hw10GEOpticsMDExtTXRefClock Extended identifier: TX Ref Clock
Options:
1. nonExtTXRefClock(0) -tx Ref Clock Input Not Required
2. extTXRefClock(1) -tx Ref Clock Input Required
3. invalid(-1) -inval… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.3 |
| hw10GEOpticsMDSONETSDHCodesL64point3 Indicate SONET/SDH Codes L-64.3 support or not.
Options:
1. notSupport(0) -not support L-64.3
2. support(1) -support L-64.3 | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.30 |
| hw10GEOpticsMDSONETSDHCodesL64point2c Indicate SONET/SDH Codes L-64.2c support or not.
Options:
1. notSupport(0) -not support L-64.2c
2. support(1) -support L-64.2c | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.31 |
| hw10GEOpticsMDSONETSDHCodesL64point2b Indicate SONET/SDH Codes L-64.2b support or not.
Options:
1. notSupport(0) -not support L-64.2b
2. support(1) -support L-64.2b | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.32 |
| hw10GEOpticsMDSONETSDHCodesL64point2a Indicate SONET/SDH Codes L-64.2a support or not.
Options:
1. notSupport(0) -not support L-64.2a
2. support(1) -support L-64.2a | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.33 |
| hw10GEOpticsMDSONETSDHCodesL64point1 Indicate SONET/SDH Codes L-64.1 support or not.
Options:
1. notSupport(0) -not support L-64.1
2. support(1) -support L-64.1 | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.34 |
| hw10GEOpticsMDSONETSDHCodesV64point3 Indicate SONET/SDH Codes V-64.3 support or not.
Options:
1. notSupport(0) -not support V-64.3
2. support(1) -support V-64.3 | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.35 |
| hw10GEOpticsMDSONETSDHCodesV64point2b Indicate SONET/SDH Codes V-64.2b support or not.
Options:
1. notSupport(0) -not support V-64.2b
2. support(1) -support V-64.2b | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.36 |
| hw10GEOpticsMDSONETSDHCodesV64point2a Indicate SONET/SDH Codes V-64.2a support or not.
Options:
1. notSupport(0) -not support V-64.2a
2. support(1) -support V-64.2a | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.37 |
| hw10GEOpticsMDEncodingRZ Indicate encoding mechanism RZ support or not.
Options:
1. nonEncodingRZ(0) -not support RZ
2. encodingRZ(1) -support RZ | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.38 |
| hw10GEOpticsMDEncodingNRZ Indicate encoding mechanism NRZ support or not.
Options:
1. nonEncodingNRZ(0) -not support NRZ
2. encodingNRZ(1) -support NRZ | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.39 |
| hw10GEOpticsMDExtCDRFunc Extended identifier: CDR function
Options:
1. nonExtCDRFunc(0) -no CDR version of XFP
2. extCDRFunc(1) -module with CDR function
3. invalid(-1) -invalid value | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.4 |
| hw10GEOpticsMDEncodingSONET Indicate encoding mechanism SONET support or not.
Options:
1. nonEncodingSONET(0) -not support SONET
2. encodingSONET(1) -support SONET | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.40 |
| hw10GEOpticsMDEncoding8B10B Indicate encoding mechanism 8B10B support or not.
Options:
1. nonEncoding8B10B(0) -not support 8B10B
2. encoding8B10B(1) -support 8B10B | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.41 |
| hw10GEOpticsMDEncoding64B Indicate encoding mechanism 64B/66B support or not.
Options:
1. nonEncoding64B(0) -not support 64B/66B
2. encoding64B(1) -support 64B/66B | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.42 |
| hw10GEOpticsMDBrMin Minimum bit rate.
Unit: 100 MBits/s | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.43 |
| hw10GEOpticsMDBrMax Maximum bit rate.
Unit: 100 MBits/s | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.44 |
| hw10GEOpticsMDSupportLenSMF Indicate the link length that is supported by the transceiver with the applicable standards
using Single-mode Fiber. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.45 |
| hw10GEOpticsMDSupportLenE50um Indicate the link length that is supported by the transceiver with the applicable standards
using 2000MHz*km (850nm) extended bandwidth 50 micron core multimode fiber.
Unit: 2m | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.46 |
| hw10GEOpticsMDSupportLen50um This value specifies the link length that is supported by the transceiver with the applicable
standards using 500MHz*km (850 and 1310nm) 50 micron core multimode fiber.
Unit: 1m | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.47 |
| hw10GEOpticsMDSupportLen62p5um This value specifies the link length that is supported by the transceiver with the applicable
standards using 200MHz*km (850 nm)/500 MHz*km (1310 nm) 62.5 micron core multimode f… | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.48 |
| hw10GEOpticsMDSupportLenCopper Indicate the minimum link length that is supported by the transceiver with copper cable.
Unit: 1m | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.49 |
| hw10GEOpticsMDExtPowerLevel Extended identifier: Power Level
Options:
1. extPowerLevel1(0) -power Level 1 Module (1.5 W max. power dissipation.)
2. extPowerLevel2(1) -power Level 2 Module (2.5W Max)
3. … | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.5 |
| hw10GEOpticsMDTransmitterSupport Indicate the transmitter support tunable or not.
Options:
1. nonTunable(0) -transmitter not support tunable
2. tunable(1) -transmitter support tunable
3. invalid(-1) -invalid… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.50 |
| hw10GEOpticsMDDetector Indicate the Detector is enable or not.
Options:
1. nonDetector(0) -detector is disable
2. detector(1) -detector is enable
3. invalid(-1) -invalid value | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.51 |
| hw10GEOpticsMDCooledTransmitterDevice Indicate the Cooled transmitter is enable or not.
Options:
1. nonSupport(0) -cooled transmitter is disable
2. support(1) -cooled transmitter is enable
3. invalid(-1) -invalid… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.52 |
| hw10GEOpticsMDWavelengthControl Indicate the wavelength control support or not.
Options:
1. nonSupport(0) -wavelength control not support
2. support(1) -wavelength control support
3. invalid(-1) -invalid v… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.53 |
| hw10GEOpticsMDTransmitterTechnologySupport Indicate the transmitter technology type.
Options:
1. vCSEL850(0) -the transmitter technology type is vCSEL850
2. vCSEL1310(1) -the transmitter technology type is vCSEL1310… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.54 |
| hw10GEOpticsMDVendorName Indicate the vendor name of a 10GE optical module. | column | OctetString | .1.3.6.1.4.1.2011.5.14.6.3.1.55 |
| hw10GEOpticsMDSupportXFIMode Indicate the XFI loopback mode support or not.
Options:
1. nonSupportXFIMode(0) -the XFI loopback mode not support
2. supportXFIMode(1) -the XFI loopback mode support
3. invali… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.56 |
| hw10GEOpticsMDSupportLinesideMode Indicate the Lineside loopback mode support or not.
Options:
1. nonSupportLinesideMode(0) -lineside loopback mode not support
2. supportLinesideMode(1) -lineside loopback mode … | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.57 |
| hw10GEOpticsMDMaxBitRateSupportedByCDR Indicate which rate is supported by the CDR.
Options:
1. maxBitRateSupportedByCDR11p1(1) -CDR support for 11.1 Gb/s
2. maxBitRateSupportedByCDR10p7(3) -CDR support for 10.7 Gb/… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.58 |
| hw10GEOpticsMDVendorOUI Indicate the vendor IEEE company ID of a 10GE optical module. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.59 |
| hw10GEOpticsMDConnector Indicate the type of 10GE optical module connector.
Options:
1. unknown(0) -unknown the type of 10GE optical module connector
2. sc(1) -the ty… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.6 |
| hw10GEOpticsMDVendorPN Indicate the part number of a 10GE optical module provided by vendor. | column | OctetString | .1.3.6.1.4.1.2011.5.14.6.3.1.60 |
| hw10GEOpticsMDVendorRev Indicate the revision level for part number provided by vendor. | column | OctetString | .1.3.6.1.4.1.2011.5.14.6.3.1.61 |
| hw10GEOpticsMDWavelength The laser wavelength. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.62 |
| hw10GEOpticsMDWaveTolerance The guaranteed +/- range of transmitter output wavelength under all normal operating conditions. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.63 |
| hw10GEOpticsMDMaxCaseTemperature Maximum Case Temperature in Degrees C. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.64 |
| hw10GEOpticsMDCcbase Cc_base. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.65 |
| hw10GEOpticsMDMaxDissipation Maximum Power Dissipation.
Max power is 8 bit value * 20 mW. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.66 |
| hw10GEOpticsMDMaxDissipationPowerDownMode Maximum Total Power Dissipation in Power Down Mode.
Max Power is 8 bit value * 10 mW. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.67 |
| hw10GEOpticsMDMaximum5P0VSupply Maximum current required by +5V Supply. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.68 |
| hw10GEOpticsMDMaximum3P3VSupply Maximum current required by +3.3V Supply. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.69 |
| hw10GEOpticsMDEthComplianceBaseEW Indicate 10GBASE-EW support or not.
Options:
1. nonEthComplianceBaseEW(0) -not support 10GBASE-EW
2. ethComplianceBaseEW(1) -support 10GBASE-EW | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.7 |
| hw10GEOpticsMDMaximum1P8VSupply Maximum current required by +1.8V Supply. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.70 |
| hw10GEOpticsMDMaximum5P2VSupply Maximum current required by -5.2V Supply. | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.71 |
| hw10GEOpticsMDVendorSN The serial number of a 10GE optical module provided by vendor. | column | OctetString | .1.3.6.1.4.1.2011.5.14.6.3.1.72 |
| hw10GEOpticsMDDateCode The date code of a 10GE optical module. | column | OctetString | .1.3.6.1.4.1.2011.5.14.6.3.1.73 |
| hw10GEOpticsMDDiagnoMonitorPowerMeasure Received power measurement type.
Options:
1. supportOMA(0) -OMA
2. supportAveragePower(1) -AveragePower | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.74 |
| hw10GEOpticsMDDiagnoMonitorTypeFECBER Module Respond to FEC BER.
Options:
1. nonSupportBER(0) -no BER Support
2. supportBER(1) -BER Support | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.75 |
| hw10GEOpticsMDEnhancedOptions Indicate enhanced Options.
Options:
1. cmu(0) -enhanced options is cmu
2. rateSelect(2) -enhanced options is rateSelect
3. fec(4) -enhanced options is fe… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.76 |
| hw10GEOpticsMDAuxInputOne Indicate which quantity is monitored by each auxiliary A/D channel one.
Options:
1. auxInputType1(0) -Auxiliary monitoring not implemented
2. auxInputType2(1) -APD Bias Vol… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.77 |
| hw10GEOpticsMDAuxInputTwo Indicate which quantity is monitored by each auxiliary A/D channel two.
Options:
1. auxInputType1(0) -Auxiliary monitoring not implemented
2. auxInputType2(1) -APD Bias Vo… | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.78 |
| hw10GEOpticsMDCCEXT CC_EXT | column | SNMPv2-SMIInteger32 | .1.3.6.1.4.1.2011.5.14.6.3.1.79 |
| hw10GEOpticsMDEthComplianceBaseLW Indicate 10GBASE-LW support or not.
Options:
1. nonEthComplianceBaseLW(0) -not support 10GBASE-LW
2. ethComplianceBaseLW(1) -support 10GBASE-LW | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.8 |
| hw10GEOpticsMDEthComplianceBaseSW Indicate 10GBASE-SW support or not.
Options:
1. nonEthComplianceBaseSW(0) -not support 10GBASE-SW
2. ethComplianceBaseSW(1) -support 10GBASE-SW | column | Enumeration | .1.3.6.1.4.1.2011.5.14.6.3.1.9 |