DOCS-IF3-MIB Table View

This object defines attributes of the CM connectivity
status. This object provides CM connectivity status
information of the CM previously available in
the SNMP table docsIfCmStatusTable.

This object defines PHY and MAC information about
the CM's upstream channels operating in Multiple Transmit
Channel (MTC) mode or in a Pre-3.0 DOSCIS transmit
channel mode. This object provides per-CM Upstream
channel information previously available in the
SNMP table docsIfCmStatusTable.

This object defines attributes that represent the CM's
registration status as tracked by the CMTS.
Refer to the individual attribute definitions for
applicability to 3.0 and 3.1 Cable Modems.

This object defines status information of the CM
currently in use Upstream Logical Channels, as reported
by the CMTS.

This object configures the association of downstream
and upstream channels to a particular MAC Domain
(MD) on a CMTS.  The creation of channels and MAC domain
object interface instances is vendor-specific.
In particular, the assignment of the channel interface
index is normally vendor-specific. Therefore,
this object is intended only for associating channels
to a MAC Domain and assumes that those channels were
previously configured.
The CMTS may have restrictions on which channels can
be configured in the same MAC Domain.  For example, it
could require the upstream channels to be from the same
line card.
This object supports the creation and deletion of multiple
instances.
Creation of a new instance of this object requires the
ChId attribute to be set.

This object identifies the scope of the Receive Channel
Configuration (RCC) and provides a top level container
for the Receive Module and Receive Channel
objects.  The CMTS selects an instance of this object
to assign to a CM when it registers.
This object supports the creation and deletion of multiple
instances.

The RCC Status object provides a read-only view of
the statically-configured (from the RccCfg object)
and dynamically-created RCCs.
The CMTS creates an RCC Status instance for each unique
MAC Domain Cable Modem Service Group (MD-CM-SG) to
which it signals an RCC to the CM.

The Receive Channel Configuration object permits
an operator to configure how CMs registered with certain
Receive Channel Profiles will configure the Receive
Channels within their profile. When a CM registers
with an RCP for which all Receive Channel Indices
(RcIds) are configured in the Receive Module object
and all Receive Channels are configured within this
object, the CMTS should use the configuration within
these objects to set the Receive Channel Configuration
returned to the CM in a REG-RSP message.  A CMTS
may require configuration of all pertinent Receive
Module and Receive Channel instances in order to register
a CM that reports a Receive Channel Profile (RCP),
including any standard Receive Channel Profiles.
If the CM reports multiple RCPs, and Receive Module
and Receive Channel objects have instances for more
than one RCP, the particular RCP selected by the CMTS
is not specified.  A CMTS is not restricted to assigning
Receive Modules based only on the contents of this
object.
This object supports the creation and deletion of multiple
instances.
Creation of a new instance of this object requires the
ChIfIndex attribute to be set and a valid reference of
a RccCfg instance.

The Receive Channel Status object reports the status
of the statically-configured and dynamically-created
Receive Channels within an RCC.

The Receive Module Configuration object permits
an operator to configure how CMs with certain Receive
Channel Profiles (RCPs) will configure the Receive
Modules within their profile upon CM registration.
 When a CM registers with an RCP for which all Receive
Module Indices (RmIds) are configured in this object
and all Receive Channels are configured within the
Receive Channel (ReceiveChannel) object, the CMTS
should use the configuration within these objects to
set the Receive Channel Configuration assigned to
the CM in a REG-RSP message.  A CMTS may require configuration
of all pertinent Receive Module and Receive
Channel instances (i.e., MIB table entries) in order
to register a CM that reports a Receive Channel Profile.
 If the CM reports multiple RCPs, and Receive Module
and Receive Channel objects have instances (i.e.,
MIB table entries) for more than one RCP reported by
the CM, the particular RCP selected by the CMTS is not
specified.  A CMTS is not restricted to assigning Receive
Modules based only on the contents of this object.
          
This object supports the creation and deletion of multiple
instances.
Creation of a new instance of this object requires the
reference of a valid RccCfg instance.

The Receive Module Status object provides a read-only
view of the statically configured and dynamically
created Receive Modules within an RCC.

This object reports the MD-DS-SG-ID and MD-US-SG-ID
associated with a MD-CM-SG-ID within a MAC Domain
and the Fiber Nodes reached by the MD-CM-SG.

This object returns the list of downstream channel
associated with a MAC Domain MD-DS-SG-ID.

This object returns the list of upstream channels
associated with a MAC Domain MD-US-SG-ID.

This object returns the set of downstream channels
that carry UCDs and MAPs for a particular upstream channel
in a MAC Domain.

This object contains MAC domain level control and
configuration attributes.

This object defines statically configured Downstream
Bonding Groups and Upstream Bonding Groups on
the CMTS.
This object supports the creation and deletion of multiple
instances.
Creation of a new instance of this object requires the
ChList attribute to be set.

This object returns administratively-configured
and CMTS defined downstream bonding groups.

This object returns administratively-configured
and CMTS-defined upstream bonding groups.

This object defines management extensions for upstream
channels, in particular SCDMA parameters.

This object defines a set of upstream channels. These
channel sets may be associated with channel bonding
groups, MD-US-SGs, MD-CM-SGs, or any other channel
set that the CMTS may derive from other CMTS processes.

This object defines a set of downstream channels.
These channel sets may be associated with channel bonding
groups, MD-DS-SGs, MD-CM-SGs, or any other channel
set that the CMTS may derive from other CMTS processes.

This object provides an in-channel received modulation
error ratio metric for CM and CMTS.

This object provides metrics and parameters associated
with received carrier, noise and interference
power levels in the upstream channels of the CMTS.

This object is used to configure the logical upstream
interfaces to perform the spectrum measurements.
This object supports creation and deletion of instances.

This object represents the DOCSIS Path Verify Statistics
collected in the cable modem device.
The CMTS controls the logging of DPV statistics in the
cable modem. Therefore the context and nature of the
measurements are governed by the CMTS and not self-descriptive
when read from the CM.

This object represents the control mechanism to enable the
dispatching of events based on the event Id. The following
rules define the event control behavior:
          
- The CmEventCtrl object has no instances or contains an
  instance with Event ID 0. All events matching the Local Log
  settings of docsDevEvReporting are sent to local log ONLY.
          
- The CmEventCtrl object contains configured instances
  Only events matching the Event Ids configured in the object
  are sent according to the settings of the docsDevEvReporting
  object.
          
  The CM does not persist instances of CmEventCtrl across
  reinitializations.

This object represents the control mechanism to enable the
dispatching of  events based on the event Id. The following
rules define the event control behavior:
          
- The CmtsEventCtrl object has no instances or contains an
  instance with Event ID 0. All events matching the Local Log
  settings of docsDevEvReporting are sent to local log ONLY.
          
- The CmtsEventCtrl object contains configured instances
  Only events matching the Event Ids configured in the object
  are sent according to the settings of the docsDevEvReporting
  object.
          
- The CMTS persists all instances of CmtsEventCtrl across
  reinitializations.

This object contains CM MAC domain level control and
configuration attributes.

This object provides configuration state information
on the CM for the Energy Management 1x1 Mode feature.

This table provides a list of spectral analysis measurements
as performed across a range of center frequencies. The table
is capable of representing a full scan of the spectrum.

This table defines Energy Management mode statistics for the
CM as reported by the CMTS.  For example, such metrics can
provide insight into configuration of appropriate EM 1x1 Mode
Activity Detection thresholds on the CM and/or to get feedback
on how/if the current thresholds are working well or are
causing user experience issues.

This object defines Energy Management 1x1 mode statistics on
the CM to provide insight into configuration of appropriate EM
1x1 Mode Activity Detection thresholds and/or to get feedback
on how/if the current thresholds are working well or are
causing user experience issues.
These statistics are only applicable/valid when the Energy
Management 1x1 mode is enabled in the CM.