CISCO-METRO-PHY-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
3
Rows
3
Columns
31

cmPhyIfTable

table
.1.3.6.1.4.1.9.10.69.1.1.1 · 1 row entry · 16 columns
Open in standard view 
This table allows physical layer related interface
configurations on an interface.
cmPhyIfEntry entry .1.3.6.1.4.1.9.10.69.1.1.1.1
A collection of objects for configuration on an
interface.
Indexes
IF-MIBifIndex
Column Syntax OID
cmPhyIfMode
This object allows the management client to configure
the mode of operation for the client interface modules.

When in 2R mode, there is no protocol type, clock rate
or monitoring to be configured i.e. the…
Enumerationr/w
Enumerated Values:
1mode2R
2mode3R
 .1.3.6.1.4.1.9.10.69.1.1.1.1.1
cmPhyIfProtocol
This object is used to specify the protocol of the data
carried over the client side interface.

This object applies to linecards which support a variety of
protocols and allow dynamic configuration of th…
ProtocolTyper/w
Textual Convention: ProtocolType Enumeration
Type Values:
1other
2unknown
3gigabitEthernet
4tenGigabitEthernet
5fibreChannel
6ficon
7escon
8sonet
9sdh
10sysplexIscCompatibility
11sysplexIscPeer
12sysplexTimerEtr
13sysplexTimerClo
14fastEthernet
15fddi
16e1
17t1
18e3
19t3
20dvb
21sdi
22its
 .1.3.6.1.4.1.9.10.69.1.1.1.1.2
cmPhyIfClockRate
This object allows the management client to set the
clock rate across the client side interface.

Due to hardware limitations, all values may not be supported.
The default value of this object depends on t…
kHzInteger32r/w
Constraints:
range: 0-10312000
 .1.3.6.1.4.1.9.10.69.1.1.1.1.3
cmPhyIfMonitor
This object allows the management client to enable
monitoring of the error counters on an interface,
by writing a value of 'true' to this object. To bypass
the monitoring hardware, a value of 'false' must be
written t…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.10.69.1.1.1.1.4
cmPhyIfLoopback
This object allows the management client to configure
loopback for the client side or trunk side interfaces.

'noLoop' - No Loopback present.
'diagnosticLoop' - This is an internal loopback, where …
Enumerationr/w
Enumerated Values:
1noLoop
2diagnosticLoop
3lineLoop
4otherLoop
 .1.3.6.1.4.1.9.10.69.1.1.1.1.5
cmPhyIfOFC
This object allows the management client to enable
OFC(Open Fibre Control) safety protocol for the client
side interfaces, by writing a 'true' value to
this object. A 'false' value would disable OFC.

The…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.10.69.1.1.1.1.6
cmPhyIfLaserSafetyControl deprecated
This object allows the management client to enable
laser safety control feature on the trunk side interfaces
by writing a true value to this object. If laser safety
control is enabled, the transmit laser on the trunk si…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.10.69.1.1.1.1.7
cmPhyIfForwardLaserControl deprecated
This object allows the management client to enable
forward laser control on the client or trunk side interfaces
by writing a true value to this object. If forward laser
control is enabled, the transmit laser is shut wh…
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.10.69.1.1.1.1.8
cmPhyIfTxBufferSize
This object applies when circuit emulation of the client
protocol is used. It allows the management client to
configure the size of the transmit buffer on the client
port. A value of 0 implies that this object does not …
bytesUnsigned32r/w
Constraints:
range: 0-65536
 .1.3.6.1.4.1.9.10.69.1.1.1.1.9
cmPhyIfAutoNegotiation
This object allows the management client to enable
auto negotiation signaling on the client side interface,
by writing a 'true' value to this object. A 'false'
value would disable auto negotiation. Setting the value
'n…
TriValuer/w
Textual Convention: TriValue Enumeration
Type Values:
1true
2false
3notApplicable
 .1.3.6.1.4.1.9.10.69.1.1.1.1.10
cmPhyIfTransType
This object is used to identify the physical layer medium used
for carrying data. For non-relevant interfaces, this value is
'unknown'.
TransmissionType
Textual Convention: TransmissionType Enumeration
Type Values:
1unknown
2copper
3optical
 .1.3.6.1.4.1.9.10.69.1.1.1.1.11
cmPhyIfRate
This object is used to specify the rate of the interface.
The value of 'unknown' implies that this object does not
apply to this interface.
CmRateTyper/w
Textual Convention: CmRateType Enumeration
Type Values:
1unknown
2auto
3oneGbps
4twoGbps
5fourGbps
6tenGbps
 .1.3.6.1.4.1.9.10.69.1.1.1.1.12
cmPhyIfNegotiatedRate
This object is used to identify the current rate of the
interface after the auto negotation. This object is valid
only if the object cmPhyIfRate is configured as 'auto'.
CmNegotiatedRateType
Textual Convention: CmNegotiatedRateType Enumeration
Type Values:
1notApplicable
2negotiating
3oneGbps
4twoGbps
5fourGbps
6tenGbps
 .1.3.6.1.4.1.9.10.69.1.1.1.1.13
cmPhyIfOverSubscription
Oversubscription allows the user to carry multiple clients
over the trunk to efficiently utilize the trunk bandwidth.

This object allows the management client to enable
over subscription on an interface …
TriValuer/w
Textual Convention: TriValue Enumeration
Type Values:
1true
2false
3notApplicable
 .1.3.6.1.4.1.9.10.69.1.1.1.1.14
cmPhyIfClientSubrate
This object allows the management client to specify the
subrate bandwidth of the oversubscribed trunk which carries
this client.

A value of 0 implies that this object does not apply to this
interface.
mega-bytes-per-secondUnsigned32r/w
Constraints:
range: 0-4240
 .1.3.6.1.4.1.9.10.69.1.1.1.1.15
cmPhyIfClientSubrateLock
This object allows the management client to lock the
subrate bandwidth on an interface, by writing a value of
'true' to this object. A 'false' value would disable the
bandwidth lock. If the clients bandwidth is locked …
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.9.10.69.1.1.1.1.16

cmPhyStatisticsTable

table
.1.3.6.1.4.1.9.10.69.1.2.1 · 1 row entry · 13 columns
Open in standard view 
This table contains the cumulative error statistics being 
collected for the different medium types, except SONET,
on the client side and an object for the optical
power level on the trunk side.
The error statistics for SONET are covered
by the sonetSectionCurrentTable and the
sonetSectionIntervalTable in the RFC1595-MIB.
cmPhyStatisticsEntry entry .1.3.6.1.4.1.9.10.69.1.2.1.1
An entry in the cmPhyStatisticsTable.
Indexes
IF-MIBifIndex
Column Syntax OID
cmPhyRxPower deprecated
This object gives the optical power level received
on the trunk side interface.

The actual value of the power level received on
the interface is the value of this object divided
by 100. This object is no…
dBmInteger32
Constraints:
range: -4000-0
 .1.3.6.1.4.1.9.10.69.1.2.1.1.1
cmPhyRxCVRD
This object represents the lower word value of the
counter associated with the
number of code violations and running disparity errors
encountered, in the receive direction.

NOTE: The object cmPhyRxCVRDO…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.69.1.2.1.1.2
cmPhyRxCVRDOverflow
This object represents the high word value of the
counter associated with the
number of code violations and running disparity errors
encountered, in the receive direction.

NOTE: The object cmPhyRxCVRD con…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.69.1.2.1.1.3
cmPhyHCRxCVRD
This object represents the counter associated with the
number of code violations and running disparity errors
encountered, in the receive direction.

This is a High Capacity (64 bit) version of the
cmPhyR…
SNMPv2-SMICounter64
Textual Convention: SNMPv2-SMICounter64 Unsigned64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.9.10.69.1.2.1.1.4
cmPhyRxHEC deprecated
This object represents the lower word value of the
counter associated with the
number of CDL HEC errors encountered, in the receive
direction.

This object has a valid value only if the protocol
type is g…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.69.1.2.1.1.5
cmPhyRxHECOverflow deprecated
This object represents the high word value of the
counter associated with the number of CDL
HEC errors encountered, in the receive direction.

This object has a valid value only if the protocol
type is gi…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.69.1.2.1.1.6
cmPhyHCRxHEC deprecated
This object represents the counter associated with the
number of CDL HEC errors encountered, in the receive
direction.
This object has a valid value only if the medium
type is gigabitEthernet/ tenGigabitEthernet. For al…
SNMPv2-SMICounter64
Textual Convention: SNMPv2-SMICounter64 Unsigned64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.9.10.69.1.2.1.1.7
cmPhyRxCRC
This object represents the lower word value of the
counter associated with CRC errors.
This object has a valid value only for interfaces that
provide CRC error monitoring.

NOTE: The object cmPhyRxCRCOverf…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.69.1.2.1.1.8
cmPhyRxCRCOverflow
This object represents the higher word value of the
counter associated with CRC errors.
This object has a valid value only for interfaces that
provide CRC error monitoring.

NOTE: The object cmPhyRxCRC con…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.69.1.2.1.1.9
cmPhyHCRxCRC
This object represents the counter associated with
CRC errors. This object has a valid value only for
interfaces that provide CRC error monitoring.

This is a High Capacity (64 bit) version of the cmPhy…
SNMPv2-SMICounter64
Textual Convention: SNMPv2-SMICounter64 Unsigned64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.9.10.69.1.2.1.1.10
cmPhyTxEncapFarEndPktErrors
This object represents the lower word value of the counter
associated with ingress error indications from the far end of
an Ethernet network, where an ESCON stream is encapsulated in
Ethernet packets. This counter is in…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.69.1.2.1.1.11
cmPhyTxEncapFarEndPktErrOverflow
This object represents the higher word value of the counter
associated with ingress error indications from the far end of
an Ethernet network, where an ESCON stream is encapsulated in
Ethernet packets. This counter is i…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.9.10.69.1.2.1.1.12
cmPhyHCTxEncapFarEndPktErrors
This object represents the counter associated with ESCON
ingress error indications from the far end of
an Ethernet network, where an ESCON stream is encapsulated in
Ethernet packets. This counter is incremented wheneve…
SNMPv2-SMICounter64
Textual Convention: SNMPv2-SMICounter64 Unsigned64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.9.10.69.1.2.1.1.13

cmPhySonetSectionTraceTable

table
.1.3.6.1.4.1.9.10.69.1.3.1 · 1 row entry · 2 columns
Open in standard view 
This table provides objects for monitoring the J0
bytes of a SONET or SDH section.
cmPhySonetSectionTraceEntry entry .1.3.6.1.4.1.9.10.69.1.3.1.1
An entry in the cmPhySonetSectionTraceTable is created
when the value of the cmPhyIfProtocol object is set to
'sonet' and the value of cmPhyIfMonitor is set to 'true'.
Indexes
IF-MIBifIndex
Column Syntax OID
cmPhySonetSectionTraceReceived
This object displays the SONET or SDH section trace bytes
received at the interface.
OctetString
Constraints:
range: 0-0
range: 16-16
range: 64-64
 .1.3.6.1.4.1.9.10.69.1.3.1.1.1
cmPhySonetSectionTraceExpected
This object defines the SONET or SDH section trace bytes
to be expected at the interface.

The default value of this object will be a zero length
string.
OctetStringr/w
Constraints:
range: 0-0
range: 16-16
range: 64-64
 .1.3.6.1.4.1.9.10.69.1.3.1.1.2