cmPhyIfClientSubrate
CISCO-METRO-PHY-MIB ·
.1.3.6.1.4.1.9.10.69.1.1.1.1.15
Object
column
r/w
mega-bytes-per-second Unsigned32
This object allows the management client to specify the
subrate bandwidth of the oversubscribed trunk which carries
this client.
A value of 0 implies that this object does not apply to this
interface.
Context
- MIB
- CISCO-METRO-PHY-MIB
- OID
.1.3.6.1.4.1.9.10.69.1.1.1.1.15- Type
- column
- Access
- readwrite
- Status
- current
- Units
- mega-bytes-per-second
- Parent
- cmPhyIfEntry
- Table
- cmPhyIfTable
- Siblings
- 15
Syntax
mega-bytes-per-second Unsigned32
Values & Constraints
Object Constraints
range: 0-4240
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| cmPhyIfMode This object allows the management client to configure
the mode of operation for the client interface modules.
When in 2R mode, there is no protocol type, clock rate… | column | Enumeration | .1.3.6.1.4.1.9.10.69.1.1.1.1.1 |
| cmPhyIfAutoNegotiation This object allows the management client to enable
auto negotiation signaling on the client side interface,
by writing a 'true' value to this object. A 'false'
value would disable… | column | TriValue | .1.3.6.1.4.1.9.10.69.1.1.1.1.10 |
| cmPhyIfTransType This object is used to identify the physical layer medium used
for carrying data. For non-relevant interfaces, this value is
'unknown'. | column | TransmissionType | .1.3.6.1.4.1.9.10.69.1.1.1.1.11 |
| cmPhyIfRate This object is used to specify the rate of the interface.
The value of 'unknown' implies that this object does not
apply to this interface. | column | CmRateType | .1.3.6.1.4.1.9.10.69.1.1.1.1.12 |
| cmPhyIfNegotiatedRate This object is used to identify the current rate of the
interface after the auto negotation. This object is valid
only if the object cmPhyIfRate is configured as 'auto'. | column | CmNegotiatedRateType | .1.3.6.1.4.1.9.10.69.1.1.1.1.13 |
| cmPhyIfOverSubscription Oversubscription allows the user to carry multiple clients
over the trunk to efficiently utilize the trunk bandwidth.
This object allows the management client to en… | column | TriValue | .1.3.6.1.4.1.9.10.69.1.1.1.1.14 |
| cmPhyIfClientSubrateLock This object allows the management client to lock the
subrate bandwidth on an interface, by writing a value of
'true' to this object. A 'false' value would disable the
bandwidth l… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.69.1.1.1.1.16 |
| cmPhyIfProtocol This object is used to specify the protocol of the data
carried over the client side interface.
This object applies to linecards which support a variety of
protoco… | column | ProtocolType | .1.3.6.1.4.1.9.10.69.1.1.1.1.2 |
| cmPhyIfClockRate This object allows the management client to set the
clock rate across the client side interface.
Due to hardware limitations, all values may not be supported.
The d… | column | kHz Integer32 | .1.3.6.1.4.1.9.10.69.1.1.1.1.3 |
| cmPhyIfMonitor This object allows the management client to enable
monitoring of the error counters on an interface,
by writing a value of 'true' to this object. To bypass
the monitoring hardwar… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.69.1.1.1.1.4 |
| cmPhyIfLoopback This object allows the management client to configure
loopback for the client side or trunk side interfaces.
'noLoop' - No Loopback present.
'diagnosticLoop… | column | Enumeration | .1.3.6.1.4.1.9.10.69.1.1.1.1.5 |
| cmPhyIfOFC This object allows the management client to enable
OFC(Open Fibre Control) safety protocol for the client
side interfaces, by writing a 'true' value to
this object. A 'false' val… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.69.1.1.1.1.6 |
| cmPhyIfLaserSafetyControl deprecated This object allows the management client to enable
laser safety control feature on the trunk side interfaces
by writing a true value to this object. If laser safety
control is ena… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.69.1.1.1.1.7 |
| cmPhyIfForwardLaserControl deprecated This object allows the management client to enable
forward laser control on the client or trunk side interfaces
by writing a true value to this object. If forward laser
control i… | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.9.10.69.1.1.1.1.8 |
| cmPhyIfTxBufferSize This object applies when circuit emulation of the client
protocol is used. It allows the management client to
configure the size of the transmit buffer on the client
port. A value… | column | bytes Unsigned32 | .1.3.6.1.4.1.9.10.69.1.1.1.1.9 |