BUNDLE-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
4
Rows
4
Columns
55

nnbundleTable

table
.1.3.6.1.4.1.562.73.1.1.1.13.1 · 1 row entry · 35 columns
Open in standard view 
Bundle management related 
parameters are defined in this table.
nnbundleTableEntry entry .1.3.6.1.4.1.562.73.1.1.1.13.1.1
Bundle parameter entries are listed in this
table.
Indexes
nnbundleId
Column Syntax OID
nnbundleId
bundleId is the identifier of a bundle. To
configure a bundle, this parameter must be
used as the index. This is assigned internally
by the system. Whenever a row creation
needs to occur in the bundleTable, the
bun…
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.1
nnbundleName
Name of the bundle. To configure a bundle,
this parameter must be set. That is, a
descriptive name should be given to a bundle.
The maximum length of a bundle name is 8
characters. This parameter is set once during …
OctetStringr/w
Constraints:
range: 1-8
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.2
nnbundleContact
Name of the person who can be contacted
for information about the bundle. The maximum
length for this parameter is 15 characters.
This parameter can be set after the bundle
is named and before the links are assigned.
OctetStringr/w
Constraints:
range: 1-15
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.3
nnbundleDescr
Brief description of the bundle. The maximum
length of this parameter is 25 characters.
This parameter can be set after the bundle
is named and before the links are assigned.
OctetStringr/w
Constraints:
range: 1-76
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.4
nnbundleEncapsulation
Specifies the type of protocol encapsulation
for the bundle. To configure protocol-specific
parameters for a bundle, the bundle must first
be encapsulated with that protocol. To
unconfigure the encapsulation type, t…
Enumerationr/w
Enumerated Values:
1noEncap
2ppp
3hdlc
4frameRelay
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.5
nnbundleDropEs
The length of time in seconds that the error
condition Errored Seconds exists before a link is
dropped. This parameter can be configured only
for multilink bundles and after the
bundle is encapsulated.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.6
nnbundleDropSes
The length of time in seconds that the error
condition Severely Errored Seconds exists
before a link is dropped. This parameter can
be configured only for multilink bundles and
after the bundle is encapsulated.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.7
nnbundleDropUas
The length of time in seconds that the error
condition Unavailable Seconds exists before a
link is dropped. This parameter can be
configured only for multilink bundles and
after the bundle is encapsulated.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.8
nnbundleDropEev
The length of time in seconds that the error
condition ESF Error Events exists before a
link is dropped. This parameter can be
configured only for multilink bundles and
after the bundle is encapsulated.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.9
nnbundleDropBes
The length of time in seconds that the error
condition Bursty Errored Seconds
(Applicable only for T1 links) exists before a
link is dropped. This parameter can be
configured only for multilink bundles and
after th…
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.10
nnbundleDropBbe
The length of time in seconds that the error
condition Threshold for Background Blocked Errors
(Applicable only for E1 links) exists before a
link is dropped. This parameter can be
configured only for multilink bund…
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.11
nnbundleDropLofc
The length of time in seconds that the error
condition Loss Of Frame Count exists before a
link is dropped. This parameter can be
configured only for multilink bundles and
after the bundle is encapsulated.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.12
nnbundleDropBpv
The length of time in seconds that the error
condition BiPolar Violation exists before a
link is dropped. This parameter can be
configured only for multilink bundles and
after the bundle is encapsulated.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.13
nnbundleDropCss
The length of time in seconds that the error
condition Controlled Slip Second exists before a
link is dropped. This parameter can be
configured only for multilink bundles and
after the bundle is encapsulated.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.14
nnbundleDropOof
The length of time in seconds that the error
condition Out Of Frame exists before a
link is dropped. This parameter can be
configured only for multilink bundles and
after the bundle is encapsulated.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.15
nnbundleDropCrc
The length of time in seconds that the error
condition Cyclic Redundancy Check exists before a
link is dropped. This parameter can be
configured only for multilink bundles and
after the bundle is encapsulated.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.16
nnbundleIpAddr
The bundle's source IP address. This is one
of the parameters required to set up IP
multiplexing for a bundle. This parameter
can be configured only when the bundle is
encapsulated. Also the parameters bundleIpAddr …
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.17
nnbundleSubnetMask
This parameter represents the source subnet
mask address. This is one of the parameters
required to set up IP multiplexing for a
bundle. This parameter is set along with the
bundleIpAddr parameter during the same
r…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.18
nnbundleSrcForwardingAddrPrimary
The bundle's destination IP address. This is
one of the parameters required to set up IP
multiplexing for a bundle. This parameter can
be configured when the bundle has been
configured for IP multiplexing. To unconf…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.19
nnbundleSrcForwardingAddrSecondary
The bundle's secondary or backup destination
address. This address will be used only if
the primary address uses an ethernet interface
and failover is enabled on that interface and
the interface goes down. The second…
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.20
nnbundleRestoreMethod
bundleRestoreMethod defines how a dropped
link of a multilink bundle will be restored.
It can be done either manually or
automatically. If the restore mode is
automatic, the parameter bundleLinkRestoralTime
should …
Enumerationr/w
Enumerated Values:
1manual
2automatic
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.21
nnbundleLinkRestoralTime
Error-free time interval (in seconds) that
must pass before a link is automatically
restored. This parameter can be set when the
bundleRestoreMethod is automatic.
secondsSNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.22
nnbundleStatus
bundleStatus shutdowns the bundle. Although
the default is 'enable,' the bundle remains
disabled until all necessary parameters are
present
Enumerationr/w
Enumerated Values:
1enable
2disable
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.23
nnbundleLinkRestore
bundleLinkRestore specifies the links to be
restored manually. This parameter is configured
when the value of bundleRestoreMethod is manual.
The user needs to specify the link/s to be
restored. LSB in the OCTET STRI…
OctetStringr/w
Constraints:
range: 4-4
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.24
nnbundleNoOfLinks
Indicates the number of links configured in
the bundle.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.25
nnbundleTotalBw
Indicates the total bandwidth for this bundle.
The bundle bandwidth is the aggregated band-
widths of all the links assigned to a
particular bundle.
kbpsSNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.26
nnbundleRowStatus
bundleRowStatus is used to add/delete a row
in the table. Adding or deleting a row
corresponds to creating a bundle or deleting
a bundle. In order to add a row to the bundle
table, a set on this parameter should be …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.27
nnbundleIpUnnumbered
Name of the bundle. To configure unnumbered,
this parameter must be set.
The maximum length of a bundle name is 8
characters.
OctetStringr/w
Constraints:
range: 1-8
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.28
nnbundleIpMulticast
Specifies the Ip multicast operation.
Enumerationr/w
Enumerated Values:
0noMcast
1pass
2block
3ospfrip2
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.29
nnbundleDirectedBcast
Enable/disable forwarding of directed broadcasts
on this interface.
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.30
nnbundleIcmpUnreachable
Enable/disable ICMP destination unreachable messages
on this interface
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.31
nnbundleIcmpRedirect
Enable/disable ICMP redirect messages on this
on this interface
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.32
nnbundleClearCounters
Perform a clearing of the counters operation
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.33
nnbundleTrackHoldDownTimer
Indicates the tracking hold down timer.
Integer32r/w
Constraints:
range: 1-100
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.34
nnbundleDropPackets
The number of packets dropped by a WAN interface
when the agent encounters packet drops due to lack of buffer availability for transmission etc. Also, packets may be dropped for various reasons like Buffer ove…
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.562.73.1.1.1.13.1.1.35

nnbundleLinkTable

table
.1.3.6.1.4.1.562.73.1.1.1.13.2 · 1 row entry · 10 columns
Open in standard view 
All the parameters related to the assigned 
links of a bundle are defined in 
bundleLinkTable. A row in this table can be 
created when a bundle with the corresponding 
bundleId already exists in the bundleTable.
nnbundleLinkEntry entry .1.3.6.1.4.1.562.73.1.1.1.13.2.1
Link parameters that relate to a
given bundle are specified in this table.
Indexes
nnbundleId nnbundleLinkT1Num
Column Syntax OID
nnbundleLinkT1Num
bundleLinkT1Num is the number of the T1 link
being added to a specific bundle. For example,
to assign link number 4, the value of this
parameter should be set to 4. However, the
design of SNMP's link creation is dif…
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.1
nnbundleLinkTimeSlots
bundleLinkTimeSlots indicates the DS0 channels
in a fractional T1 link. The LSB in the OCTET
STRING represents DS0 channel number 1. For
example, to assign DS0 channels 1-4, the value
of this parameter should be set…
OctetStringr/w
Constraints:
range: 4-4
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.2
nnbundleLinkType
bundleLinkType specifies the interface type
(i.e.,CT3,T1,T3,HSSI,V35,X21,S530,S530A,S449,S232 etc.,)
of the link being assigned to the bundle. This is a
mandatory parameter for Row creation in the
bundleLinkTable.
Enumerationr/w
Enumerated Values:
1ct3
2t1
3e1
4hssi
5t3
6v35
7ft1
8fe1
9x21
10s530
11s530A
12s449
13s232
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.3
nnbundleLinkSpeed
The bundleLinkSpeed specifies the transmission
speed of all DS0 channels in a bundle.
Enumerationr/w
Enumerated Values:
1kbps56
2kbps64
3notApplicable
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.4
nnbundleLinkInvertedData
Setting bundleLinkInvertedData parameter to
true will have the system invert data on all
DS0 channels before transmission. Data
inversion is used only for HDLC-encapsulated
bundles.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.5
nnbundleLinkPhysIfNum
bundleLinkPhysIfNum specifies the interface
number of the interface type such as CT3,
HSSI, T3 on which this link is being created.
This variable holds significance only for
link types CT3, HSSI and T3. It is a
mand…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.6
nnbundleLinkDiffDelay
bundleLinkDiffDelay specifies the maximum
differential delay allowed on the links in a
multilink bundle. If the packet delay on any
link exceeds the differential delay set for a
bundle, that link is dropped from th…
milli-secondsSNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.7
nnbundleLinkBw
bundleLinkBw indicates the bandwidth of the
link. The bandwidth of an individual link
depends upon its configuration. For example,
in a link of type T1, its bandwidth will
depend upon whether the link is a full T1…
kbpsSNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.8
nnbundleLinkStatus
bundleLinkStatus indicates whether a
particular link in a bundle is up or down.
The link can go down due to various reasons
such as differential delay, a broken link,
or negotiation problems at the far end.
Enumeration
Enumerated Values:
1up
2down
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.9
nnbundleLinkRowStatus
bundleLinkRowStatus is used to add or delete
a row in the table. To create a row, this
parameter is set to value 4(createAndGo). To
delete a row, this parameter is set to a value
6(destroy).
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.562.73.1.1.1.13.2.1.10

nnbundleTrackTable

table
.1.3.6.1.4.1.562.73.1.1.1.13.3 · 1 row entry · 4 columns
Open in standard view 
All the parameters related to bundle
tracking are includede in BundleTrackTable.
nnbundleTrackEntry entry .1.3.6.1.4.1.562.73.1.1.1.13.3.1
Bundle Track parameters that relate to a
given bundle are specified in this table.
Indexes
nnbundleId nntrackIntfId
Column Syntax OID
nntrackIntfId
trackIntfId is the identifier of the
bundle being tracked.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.3.1.1
nntrackIntfName
Name of the bundle being tracked.
OctetStringr/w
Constraints:
range: 1-8
 .1.3.6.1.4.1.562.73.1.1.1.13.3.1.2
nntrackIntfStatus
bundleStatus displays the status of the
bundle being tracked.
Enumeration
Enumerated Values:
1up
2down
 .1.3.6.1.4.1.562.73.1.1.1.13.3.1.3
nntrackIntfRowStatus
Used to configure or delete a tracking interface. To configure
a interface, set the value of this object to createAndGo. To delete
a interface, set the value of this object to destroy.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.562.73.1.1.1.13.3.1.4

nnloopbackIfTable

table
.1.3.6.1.4.1.562.73.1.1.1.13.4 · 1 row entry · 6 columns
Open in standard view 
A list of Loopback Interface table entries 
for this entity.
nnloopbackIfTableEntry entry .1.3.6.1.4.1.562.73.1.1.1.13.4.1
Loopback Interface parameter entries are
listed in this table.
Indexes
nnloopbackIfId
Column Syntax OID
nnloopbackIfId
loopbackIfId is the identifier of a loopback
Interface. To configure a loopback, this
parameter must be used as the index. This is
assigned internally by the system. Whenever a
row creation needs to occur in the
loo…
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.562.73.1.1.1.13.4.1.1
nnloopbackIfName
Name of the loopback If. To configure a
loopback Interface,this parameter must be set.
That is, a descriptive name should be given to
a loopback inteface. The maximum length of a
name is 8 characters. This parameter i…
OctetStringr/w
Constraints:
range: 1-8
 .1.3.6.1.4.1.562.73.1.1.1.13.4.1.2
nnloopbackIfIpAddr
The loopback's source IP address. This is one
of the parameters required to set up loopback
interface. The parameters loopbackIfIpAddr
and loopbackIfSubnetMask have to be set
together during the same request.
To …
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.562.73.1.1.1.13.4.1.3
nnloopbackIfSubnetMask
This parameter represents the source subnet
mask address. This is one of the parameters
required to set up loopback interface.
This parameter is set along with the
loopbackIfIpAddr parameter during the same
request.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.562.73.1.1.1.13.4.1.4
nnloopbackIfStatus
loopbackIfStatus shows the current status
of the loopback interface.
Enumeration
Enumerated Values:
1up
2down
 .1.3.6.1.4.1.562.73.1.1.1.13.4.1.5
nnloopbackIfRowStatus
loopbackIfRowStatus is used to add/delete a
row In the table. Adding or deleting a row
corresponds to creating a loopback or deleting
a loopback. In order to add a row to the
loopback table, a set on this parameter …
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.562.73.1.1.1.13.4.1.6