APPLIC-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view

Tables

Rows

Columns

249

lseGroupTable

table mandatory

.1.3.6.1.4.1.81.19.1.1 · 1 row entry · 25 columns

Open in standard view

lseGroupEntry entry .1.3.6.1.4.1.81.19.1.1.1

Indexes

No indexes recorded

Column	Syntax	OID
lseGroupId mandatory Slot number in which the group is installed.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.1.1.1.1`
lseGroupFastOpen mandatory Setting the value of this attribute to ON activates the port for short idle time when code violation was detected.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.2`
lseGroup10MSqlt mandatory Setting the value of this attribute to ON activates the mechanism of detection preamble of 10Mhz.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.3`
lseGroupSmartSqlt obsolete Control the mechnism of the input sensitivity of the port.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.4`
lseGroupCParameter mandatory Defines the number of consecutive collisions the port waits before it ceases transmitting of 512 bits time toward the station.	Integer32r/w	`.1.3.6.1.4.1.81.19.1.1.1.5`
lseGroupIPGJamLength mandatory Defines the IPG jam length in Ethernet bit time (100nS) start at 16 bit time in steps of 16, to 112 bit time. For LFE-100, (Fast Ethernet bit time (10nS)) values are from 48 bit times (480nano-seconds) in step of 4, …	Integer32r/w	`.1.3.6.1.4.1.81.19.1.1.1.6`
lseGroupJamLength mandatory Defines the Jam Length in time starting from 8 (800micro-seconds) to 120 (12mili-seconds). Each step of 8 is equal 800micro-seconds. For LFE-100, values are from 8 (80micro-seconds) to 32 (320micro-seconds), each step…	Integer32r/w	`.1.3.6.1.4.1.81.19.1.1.1.7`
lseGroupDataBlinderLength mandatory Defines the Data Blinder Length in Ethernet bit time (100nS) start at 16 bit time in steps of 16 to 112 bit time. For LFE-100, (Fast Ethernet bit time (10nS)) values are from 0 bit times in step of 4, to 124 (1240na…	Integer32r/w	`.1.3.6.1.4.1.81.19.1.1.1.8`
lseGroupIPGDataLength mandatory Defines the IPG (Inter Packet Gap) length in Ethernet bit time (100nS) starting at 16 bit time in steps of 16 to 112 bit time. For LFE-100, (Fast Ethernet bit time (10nS)) values are from 48 bit times (480nano-seconds…	Integer32r/w	`.1.3.6.1.4.1.81.19.1.1.1.9`
lseGroupActiveMonitor mandatory This attribute defines the module which is the high-speed bus active monitor.	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.10`
lseGroupBackbone12 mandatory Port 1 and 2 in the board perform as Backbone link. lse208 - upper cluster is RX only and lower cluster is TX only. lse404 - upper port is Rx only and second port is Tx only. Two remains port are performed as regular fo…	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.11`
lseGroupSetDefaults mandatory Set all hardware parameters to their default values. This item will always return a value of off(2), since it acts like a toggle switch.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.12`
lseGroupBackbone34 mandatory Port 3 and 4 in the board performed as Backbone link. lse404 - Third port is Rx only and forth port is Tx only. Two remaining ports performed as regular foirl interfaces.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.13`
lseGroupBackboneRedun12 mandatory Value on(1) of this attribute defines a redundancy (backup) relationship between Backbone port 1 and backbone port 2 on a LANswiltch module.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.14`
lseGroupBackoffFromJam mandatory Value on(1) of this attribute defines non-consecutive jam after a collision has occured in LANswitch modules.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.15`
lseGroupCAMClear mandatory Value on(1) of this attribute causes the LANSwitch module to clear the CAM tables.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.16`
lseGroupJamPrevent mandatory Jam prevent flag. Functionaly, Jam prevent is a back-pressure into the line direction. There are two modes of opration: 1) automatic - the sensor gets the items status from HW 2) manual - the sensor gets the items …	Enumerationr/w Constraints: `range: 1-4`	`.1.3.6.1.4.1.81.19.1.1.1.17`
lseGroupNormOpCl mandatory Normaly Open/Close flag. When open(1) state is set, the sensor should activate a delay mechanism for the module to operate at Normaly-Closed mode for 30 seconds in order to enable the port's CAM to learn the current seg…	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.18`
lseGroupNormOpDelay mandatory When sets to a value greater than 0 (zero) and the MIB item lseGroupNormOpCl is equal to closed(2), this item define the time delay that the module will remain in normally open mode before it will move to normaly clos…	Integer32r/w	`.1.3.6.1.4.1.81.19.1.1.1.19`
lseGroupAutoPartitionEnable mandatory Enables autopartition mechanism support in the group level for each port of the group.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.20`
lseGroupWorkState mandatory One of the possible states of the module: this item indicates if the module is runing or booting. The value runAndBoot(3) indicates a serious software problem.	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.21`
lseGroupBITResult mandatory The Bit Indication Test in state 'faulty' indicates a problem. The agent should send a fault trap in this case.	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.22`
lseGroupAssignSlots mandatory In a multi-backbone configuration within a single HUB, this item enables to assign backbone module with specific slot numbers. Only packets from these slots should be handled by the backbone module, Packets from other…	OctetStringr/w	`.1.3.6.1.4.1.81.19.1.1.1.23`
lseGroupHSBMonStatus mandatory This is a bit-masked attribute which displays events which may cause HSB Reset. When a bit is '1', the relevant evet may cause HSB Reset. When a bit is '0', the relevant evet will not cause HSB Reset. The following are …	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.1.1.1.24`
lseGroupEnableHSBReset mandatory This item enables/disables the HSB Reset mechanism in the module.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.1.1.25`

lseIntPortTable

table mandatory

.1.3.6.1.4.1.81.19.1.2.1 · 1 row entry · 46 columns

Open in standard view

lseIntPortEntry entry .1.3.6.1.4.1.81.19.1.2.1.1

An entry in the table, containing data about a single internal LanSwitch bank.

Indexes

No indexes recorded

Column	Syntax	OID
lseIntPortGroupId mandatory Id of the group to which the port belongs.	Integer32	`.1.3.6.1.4.1.81.19.1.2.1.1.1`
lseIntPortId mandatory Number of LanSwitch port in the board.	Integer32	`.1.3.6.1.4.1.81.19.1.2.1.1.2`
lseIntPortIOMode mandatory on(1) activates IO mode in which all packets on the high-speed bus that were not captured by any regular port are captured by the I/O port.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.3`
lseIntPortResetSwitchCAM mandatory Acting like toggle switch thus always returns off(2) on read. When set to on(1), causes the reset of the LANswitch CAM (addresses) memory.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.4`
lseIntPortVideoPacket mandatory When set to on(1), all Tx packets toward the high-speed bus to video type packets.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.5`
lseIntPortPriorityStateMachine mandatory Setting the value of this attribute to on(1) activates the priority mechanism.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.6`
lseIntPortActiveBroadcastPriority mandatory Setting the value of this attribute to on(1) activates the active broadcast mode in priority mechanism.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.7`
lseIntPortPriorityLevel mandatory This attribute defines the priority levels of Tx packets toward the high-speed bus. The highest priority is broadcast(1).	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.8`
lseIntPortSuperPriorityEnable mandatory When limited space is left in Tx buffer, only the highest priority packets are accepted. This in turn can create a situation in which one port tries to send a packet and never gets its chance to be accepted. In or…	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.9`
lseIntPortRoutingMode mandatory generic(1) - examines all the packets that are not members of any virtual network. net(2) - examines only the packets that have the port's network number. allPackets(4) - examine all packets regardless of their routin…	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.10`
lseIntPortGlobal mandatory Setting the global mode to on(1) sets the port in a network routing mode that examines all packets that are not members of all virtual networks.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.11`
lseIntPortLearnIOCAM mandatory Setting this parameter to on(1) enables an I/O port to learn incoming MAC addresses received in its port and store them in its CAM. Packets with destination address that match the CAM addresses are not transferred to t…	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.12`
lseIntPortSecurity mandatory Setting the value of this attribute to on(1) activates the security mode.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.13`
lseIntPortIgnoreBusy mandatory Setting the value of this attribute to on(1) activates the ignore busy mode. The busy signal toward the high-speed bus is not activated even though the TX buffer is full.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.14`
lseIntPortRetryPriorityLevel1 mandatory The port increases the priority level of the high-speed bus packets after the defined number (0..31) trials.	Integer32r/w	`.1.3.6.1.4.1.81.19.1.2.1.1.15`
lseIntPortRetryPriorityLevel2 mandatory The port increases the priority level of the high-speed bus packets after the defined number (0..255) trials.	Integer32r/w	`.1.3.6.1.4.1.81.19.1.2.1.1.16`
lseIntPortRetryPriorityLevel3 mandatory The port increases the priority level of the high-speed bus packets after the defined number (0..255) trials.	Integer32r/w	`.1.3.6.1.4.1.81.19.1.2.1.1.17`
lseIntPortIgnoreProtocolType mandatory Any packet regardless of the protocol type is received from the high-speed bus.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.18`
lseIntPortCompanyMAC mandatory The attribute defines the first three bytes of the MAC address of the video host server.	OctetStringr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.19`
lseIntPortTxSafetyZone mandatory Defines the Tx Safety Zone in bits.	Integer32r/w	`.1.3.6.1.4.1.81.19.1.2.1.1.20`
lseIntPortRxSafetyZone mandatory Defines the Rx Safety Zone in bits.	Integer32r/w	`.1.3.6.1.4.1.81.19.1.2.1.1.21`
lseIntPortTxBurstLength mandatory Defines the TX Burst Length in bits.	Integer32r/w Constraints: `range: 1-65535`	`.1.3.6.1.4.1.81.19.1.2.1.1.22`
lseIntPortSecurityIntruder mandatory The value on(1) of this attribute reflects a security violation occurrence.	Enumeration Constraints: `range: 1-65535`	`.1.3.6.1.4.1.81.19.1.2.1.1.23`
lseIntPortJabber mandatory Value on(1) of this attribute reflects that jabber was transmitted to the port by the high-speed bus.	Enumeration	`.1.3.6.1.4.1.81.19.1.2.1.1.24`
lseIntPortCAM mandatory 112 bytes of MAC addresses. Each contains one byte of the port number and six bytes of the MAC address. This enables to send 16 MAC Addresses ( 16*7=112 bytes)	OctetStringr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.25`
lseIntPortVideoStateMachine mandatory Setting the value of this attribute to on(1) activates the video state machine mode. Received packets are filtered by demand from the station.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.26`
lseIntPortTransmitWeight mandatory Defines the Transmit Weight of the frames for the current LANswitch port toward the high - speed bus.	Integer32r/w	`.1.3.6.1.4.1.81.19.1.2.1.1.27`
lseIntPortSuperPriority mandatory Setting the value of this attribute to on(1) activates the retry priority functions.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.28`
lseIntPortAlignment mandatory The number of alignment errors observed on a specified port.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.1.2.1.1.29`
lseIntPortRxReject obsolete The number of Rx buffer full observed on a specified port, from the line toward the High-speed bus.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.1.2.1.1.30`
lseIntPortTxReject obsolete The number of Tx buffer full observed on a specified port, from the line toward the High-speed bus.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.1.2.1.1.31`
lseIntPortRxEmpty0 mandatory Define the highest threshold to receive packets from the HSB. This parameter is relevant when the receive buffer is full. When the buffer reached this threshold, all packets will be rejected. Version 7.0	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.1.2.1.1.32`
lseIntPortRxEmpty1 mandatory Define the middle threshold to receive packets from the HSB. This parameter is relevant when the receive buffer is almost full. When the buffer reached this threshold, the only packets that the port will receive will be…	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.1.2.1.1.33`
lseIntPortRxEmpty2 mandatory Define the lowest threshold to receive packets from the HSB. This parameter is relevant when the receive buffer is almost full. When the buffer reached this threshold, the only packets that the port will receive will be…	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.1.2.1.1.34`
lseIntPortSuperNetNumber mandatory If the internal port supports SuperNet mode, the user have to define the supernet number. Default value is 0. Change of this number when the internal port is Generic, Global or Global SuperNet must be blocked by the s…	Integer32r/w	`.1.3.6.1.4.1.81.19.1.2.1.1.35`
lseIntPortGlobalSuperNet mandatory An internal port that is part of all SuperNets is set to Global SuperNet routing. The SuperNet number is 15 in this case.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.36`
lseIntPortMACAddress mandatory The MAC address of the port, if it has. If not, an octet string of length 0.	OctetString	`.1.3.6.1.4.1.81.19.1.2.1.1.37`
lseIntPortIgnoreRoutingMode mandatory When this parameter is 'ignore', the LANSwitch port monitors all packets without paying attention to the virtual net assignment.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.38`
lseIntPortCAMLastChange mandatory This attribute contains the value of sysUpTime at the time any change occured to the content of the specific CAM.	RFC1155-SMITimeTicks Textual Convention: RFC1155-SMITimeTicks `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.1.2.1.1.39`
lseIntPortCopiedPort mandatory The port monitored on the LANswitch bus by the LSE-PM module. The value of this item is: 32*(S-1)+P, where S is the slot number in the hub and P the port within the slot (1.. 32). When the value of this item is 0, th…	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.1.2.1.1.40`
lseIntPortBroadcastBehavior mandatory This item relates only to LSE-PM modules. The value of this item defines the method by which the module treats broadcast and multicast packets.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.41`
lseIntPortFilteringMethod mandatory This item is relevant only to the LSE-PM module. The value of this item defines the filtering method used to capture packets from the Cellenium bus to the Ethernet connection.	Enumerationr/w Constraints: `range: 1-65535`	`.1.3.6.1.4.1.81.19.1.2.1.1.42`
lseIntPortSetFilter mandatory This item is relevant only to the LSE-PM module. The item is used to add new addresses to the module's filtering table. The string is a sequence of MAC addresses, 6 bytes each. When the item is set, each address in th…	OctetStringr/w Constraints: `range: 1-65535`	`.1.3.6.1.4.1.81.19.1.2.1.1.43`
lseIntPortRemoveFilter mandatory This item is relevant only to the LSE-PM module. The item is used to remove existing addresses from the module's filtering table. The string is a sequence of MAC addresses, 6 bytes each. When the item is set, all ad…	OctetStringr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.44`
lseIntPortClearFilter mandatory This item is relevant only to the LSE-PM module. The item acts as a toggle switch: when its value is set to clear(2), the contents of the module's filtering tables are cleared. This item always returns an empty string…	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.2.1.1.45`
lseIntPortMonitorMissedEvents mandatory This item is relevant only to LSE-PM modules. The value of the counter is the number of packets that were not captured by the port as a result of overload on the Ethernet line, though the port's filter was configured…	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.1.2.1.1.46`

lseIntPortMACAddTable

table mandatory

.1.3.6.1.4.1.81.19.1.2.2.1 · 1 row entry · 4 columns

Open in standard view

lseIntPortMACAddEntry entry .1.3.6.1.4.1.81.19.1.2.2.1.1

An entry in the table containing data about a single internal switch port.

Indexes

No indexes recorded

Column	Syntax	OID
lseIntPortMACAddGroupId mandatory Id of the group to which the port belongs.	Integer32	`.1.3.6.1.4.1.81.19.1.2.2.1.1.1`
lseIntPortMACAddPortId mandatory The LANswitch port number in the board.	Integer32	`.1.3.6.1.4.1.81.19.1.2.2.1.1.2`
lseIntPortMACAddLAId mandatory The lower 2 bytes of the Last MAC Address on the previous list. Use the 0 value to start from the beginning of the list.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.1.2.2.1.1.3`
lseIntPortMACAddList mandatory This item contains MAC address (source addresses) of the port. Each MAC address is 6 bytes long. The list is started with the MAC address that follows the lseIntPortMACAddLAId.	OctetString	`.1.3.6.1.4.1.81.19.1.2.2.1.1.4`

lseIntPortFilterTable

table mandatory

.1.3.6.1.4.1.81.19.1.2.3.1 · 1 row entry · 4 columns

Open in standard view

lseIntPortFilterEntry entry .1.3.6.1.4.1.81.19.1.2.3.1.1

This table is supported only for the LSE-PM module.
The table reports the contents of the port's filtering
mechanism.

Indexes

No indexes recorded

Column	Syntax	OID
lseIntPortFilterGroupId mandatory This item is relevant only for the LSE-PM module. The item defines the group to which the port belongs (i.e., the module number).	Integer32	`.1.3.6.1.4.1.81.19.1.2.3.1.1.1`
lseIntPortFilterPortId mandatory This item is relevant only for the LSE-PM module. The item defines the number of the LANswitch port in the board.	Integer32	`.1.3.6.1.4.1.81.19.1.2.3.1.1.2`
lseIntPortFilterLAId mandatory This item is relevant only for the LSE-PM module. The item contains the lower 2 bytes of the Last MAC Address on the previous list. Use the 0 value to start from the beginning of the list.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.1.2.3.1.1.3`
lseIntPortFilterList mandatory This item is relevant only for the LSE-PM module. The item contains the MAC addresses in the filter. Each MAC address is 6 bytes long. The list is started with the MAC address that follows the lseIntPortFilterLAId.	OctetString	`.1.3.6.1.4.1.81.19.1.2.3.1.1.4`

lseIntPortMACVlanTable

table mandatory

.1.3.6.1.4.1.81.19.1.2.4 · 1 row entry · 5 columns

Open in standard view

This table extends the lseIntPortMACAddTable table with VLAN support
providing mirrow of CAM content arranged by port and Vlan. The table
supports the show cam commands for stack switch products.

lseIntPortMACVlanEntry entry .1.3.6.1.4.1.81.19.1.2.4.1

Indexes

No indexes recorded

Column	Syntax	OID
lseIntPortMACVlanGroupId mandatory Id of the group to which the port belongs.	Integer32	`.1.3.6.1.4.1.81.19.1.2.4.1.1`
lseIntPortMACVlanPortId mandatory The LANswitch port number in the board.	Integer32	`.1.3.6.1.4.1.81.19.1.2.4.1.2`
lseIntPortMACVlanVlan mandatory Id of the Vlan	Integer32	`.1.3.6.1.4.1.81.19.1.2.4.1.3`
lseIntPortMACVlanLAId mandatory The lower 2 bytes of the Last MAC Address on the previous list. Use the 0 value to start from the beginning of the list.	Integer32	`.1.3.6.1.4.1.81.19.1.2.4.1.4`
lseIntPortMACVlanMAClist mandatory This item contains MAC address (source addresses) of the port. Each MAC address is 6 bytes long. The list is started with the MAC address that follows the lseIntPortMACVlanLAId.	OctetString	`.1.3.6.1.4.1.81.19.1.2.4.1.5`

lsePortTable

table mandatory

.1.3.6.1.4.1.81.19.1.3.1 · 1 row entry · 4 columns

Open in standard view

lsePortEntry entry .1.3.6.1.4.1.81.19.1.3.1.1

An entry in the table containing data about a single external switch port.

Indexes

No indexes recorded

Column	Syntax	OID
lsePortGroupId mandatory Id of the group to which the port belongs.	Integer32	`.1.3.6.1.4.1.81.19.1.3.1.1.1`
lsePortId mandatory Number of LanSwitch port in the board.	Integer32 Constraints: `range: 0-100`	`.1.3.6.1.4.1.81.19.1.3.1.1.2`
lsePortPolarity mandatory Setting the value of this attribute to ON activates the automatic port polarity detection mode.	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.3.1.1.3`
lsePortBackboneStatus mandatory It is the status of a single port that associated with a particular Backbone port. It is utilized by the Agent in the Soft Redundancy algorithm between Backbone ports in LANswitch environment	Enumerationr/w	`.1.3.6.1.4.1.81.19.1.3.1.1.4`

lhsGroupTable

table mandatory

.1.3.6.1.4.1.81.19.2.1 · 1 row entry · 3 columns

Open in standard view

Table with group-related parameters.

lhsGroupEntry entry .1.3.6.1.4.1.81.19.2.1.1

Entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
lhsGroupId mandatory Unique slot identifier in which the module is located.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.2.1.1.1`
lhsGroupMainSWVersion mandatory Software version of the main CPU.	RFC1213-MIBDisplayString Textual Convention: RFC1213-MIBDisplayString `OctetString`	`.1.3.6.1.4.1.81.19.2.1.1.2`
lhsGroupProtocolType mandatory This attribute set the protocol type in which the LHB is collecting from the high-speed bus.	Enumerationr/w Constraints: `range: 0-100`	`.1.3.6.1.4.1.81.19.2.1.1.3`

lhsPortTable

table mandatory

.1.3.6.1.4.1.81.19.2.2 · 1 row entry · 15 columns

Open in standard view

Table with port-related parameters.

lhsPortEntry entry .1.3.6.1.4.1.81.19.2.2.1

Entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
lhsPortGroupId mandatory Slot index in which the module is located.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.2.2.1.1`
lhsPortId mandatory Port number to which the data is related.	Integer32 Constraints: `range: 0-100` Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.2.2.1.2`
lhsTxUCast mandatory Number of unicast packets transmitted.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.3`
lhsTxBCast mandatory Number of broadcast packets transmitted.	RFC1155-SMICounter Constraints: `range: 0-100` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.4`
lhsTxMCast mandatory Number of multicast packets transmitted.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.5`
lhsTxUrunErr mandatory Number of transmit packet underruns.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.6`
lhsTxParErr mandatory Number of transmit packet parity errors.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.7`
lhsRxUCast mandatory Number of unicast packets received.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.8`
lhsRxBCast mandatory Number of broadcast packets received.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.9`
lhsRxMCast mandatory Number of multicast packets received.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.10`
lhsRxOrunErr mandatory Number of receive overrun errors.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.11`
lhsRxParErr mandatory Number of receive parity errors.	RFC1155-SMICounter Constraints: `range: 6-6` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.12`
lhsRxRscErr mandatory Number of receive resource errors.	RFC1155-SMICounter Constraints: `range: 6-6` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.13`
lhsRxBadTypeErr mandatory Number of bad frame type packets received.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.2.2.1.14`
lhsLinkStatus mandatory This attribute describes the status of the optical link as detected by the sensor software.	Enumeration Constraints: `range: 1-255`	`.1.3.6.1.4.1.81.19.2.2.1.15`

lsBusStatsPriorityTable

table mandatory

.1.3.6.1.4.1.81.19.3.2.13 · 1 row entry · 3 columns

Open in standard view

A list of priority count entries.

lsBusStatsPriorityEntry entry .1.3.6.1.4.1.81.19.3.2.13.1

A list of statistics related to a specific priority level on
the LANswitch bus.

Indexes

No indexes recorded

Column	Syntax	OID
lsBusStatsPriorityIndex mandatory The priority for which this entry reports statistics .	Integer32	`.1.3.6.1.4.1.81.19.3.2.13.1.1`
lsBusStatsPriorityPkts mandatory The total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.	RFC1155-SMICounter Constraints: `range: 0-7` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.2.13.1.2`
lsBusStatsPriorityOctets mandatory The total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.	RFC1155-SMICounter Constraints: `range: 0-7` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.2.13.1.3`

lsBusStatsVirtualNetTable

table mandatory

.1.3.6.1.4.1.81.19.3.2.15 · 1 row entry · 3 columns

Open in standard view

A list of virtual net statistics.

lsBusStatsVirtualNetEntry entry .1.3.6.1.4.1.81.19.3.2.15.1

A list of staistics related to a specific virtual net which
exists on the LANswitch bus.

Indexes

No indexes recorded

Column	Syntax	OID
lsBusStatsVirtualNet mandatory The virtual net for which this entry reports statistics .	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.3.2.15.1.1`
lsBusStatsVirtualNetPackets mandatory The number of good packets that were transmitted to this virtual net by ports in this hub.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.2.15.1.2`
lsBusStatsVirtualNetOctets mandatory The number of octets in good packets that were transmitted to this virtual net by ports in this hub.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.2.15.1.3`

lsPortControlTable

table mandatory

.1.3.6.1.4.1.81.19.3.3.1 · 1 row entry · 6 columns

Open in standard view

A list of port control entries.

lsPortControlEntry entry .1.3.6.1.4.1.81.19.3.3.1.1

A list of parameters that set up the collection
of extended statistics related to LANswitch ports.
Data is collected in the lsPortExtendedStatsTable.

Indexes

No indexes recorded

Column	Syntax	OID
lsPortControlIndex mandatory An index that uniquely identifies an entry in the lsPortControlTable. Each such entry defines a function that monitors ports and places statistics about them in the portTable on behalf of this lsPortControlEntry.	Integer32	`.1.3.6.1.4.1.81.19.3.3.1.1.1`
lsPortControlDataSource mandatory This object identifies the source of the data for this instance of the port function. The statistics in this group reflect all packets on the LANswitch bus that are trasferred by the lsPortFilterTable. This object may n…	ObjectIdentifierr/w	`.1.3.6.1.4.1.81.19.3.3.1.1.2`
lsPortControlTableSize mandatory The number of ports for which SW counters are collected by the agent. This number is limited to 5.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.3.3.1.1.3`
lsPortControlLastDeleteTime mandatory The value of sysUpTime when the last entry was deleted from the portion of the portTable associated with this lsPortControlEntry. If no deletions have occurred, this value shall be zero.	RFC1155-SMITimeTicks Textual Convention: RFC1155-SMITimeTicks `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.1.1.4`
lsPortControlOwner mandatory The entity that configured this entry and is therefore using the resources assigned to it.	RFC1213-MIBDisplayStringr/w Textual Convention: RFC1213-MIBDisplayString `OctetString`	`.1.3.6.1.4.1.81.19.3.3.1.1.5`
lsPortControlStatus mandatory The status of this lsPortControl entry. If this object is not equal to valid(1), all associated entries in the lsPortTable, shall be deleted by the agent.	Enumerationr/w	`.1.3.6.1.4.1.81.19.3.3.1.1.6`

lsPortFilterTable

table mandatory

.1.3.6.1.4.1.81.19.3.3.2 · 1 row entry · 2 columns

Open in standard view

A list of LANswitch ports to be monitored on the high-speed bus.
The OID of this table is a legitimate value for the 
lsPortControlDataSource.
When this OID is a source for the host table, a port in the 
table has the same meaning as an instruction to the agent 
to collect statistics for all the hosts connected to that port. 
The maximum size of this table is 5 entries

lsPortFilterEntry entry .1.3.6.1.4.1.81.19.3.3.2.1

An entry in the filter table.

Indexes

No indexes recorded

Column	Syntax	OID
lsPortFilter mandatory The port monitored on the LANswitch bus. The value of this item is: (16*S-1)+P, where S is the slot number in the hub (1..16) and P the port within the slot (1..N).	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.3.3.2.1.1`
lsPortFilterStatus mandatory The status of this lsPortFilter entry. When the status is valid, the port defined in the corresponding lsPortFilter is a part of the filter.	Enumerationr/w Constraints: `range: 6-6`	`.1.3.6.1.4.1.81.19.3.3.2.1.2`

lsPortTable

table mandatory

.1.3.6.1.4.1.81.19.3.3.4 · 1 row entry · 7 columns

Open in standard view

A list of port entries. Each entry contains statistical 
data pertaining to a single port. An entry is 
maintained at all times for each of the LANswitch 
ports that exist in the hub. This table is not controlled 
by the lsPortControlTable.

lsPortEntry entry .1.3.6.1.4.1.81.19.3.3.4.1

A collection of statistics for a particular LANswitch port.

Indexes

No indexes recorded

Column	Syntax	OID
lsPortNumber mandatory The monitored port. The value of this item is: 16*(S-1)+P, where S is the slot number in the hub (1..16) and P the port within the slot (1..N).	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.3.3.4.1.1`
lsPortInPkts mandatory The number of good packets transmitted through this port into the LANswitch bus .	RFC1155-SMICounter Constraints: `range: 4-4` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.4.1.2`
lsPortInFCSErrors mandatory The number of packets with FCS errors transmitted through this port into the LANswitch bus .	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.4.1.3`
lsPortInTooLongPkts mandatory The number of packets longer than 1518 bytes transmitted through this port into the LANswitch bus .	RFC1155-SMICounter Constraints: `range: 1-255` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.4.1.4`
lsPortInOctets mandatory The number of octets in good packets (excluding framing bits but including FCS octets) transmitted through this port into the LANswitch bus .	RFC1155-SMICounter Constraints: `range: 1-255` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.4.1.5`
lsPortInTotalErrors mandatory This item is a summation of all errors on this port. It contains the total hardware errors related to a specific port.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.4.1.6`
lsPortInCollisions mandatory This counter is incremented by one for any CarrierEvent signal on the port for which the CollisionEvent signal on this port is also asserted.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.4.1.7`

lsPortExtendedStatsTable

table mandatory

.1.3.6.1.4.1.81.19.3.3.6 · 1 row entry · 6 columns

Open in standard view

A list of port entries.

lsPortExtendedStatsEntry entry .1.3.6.1.4.1.81.19.3.3.6.1

A collection of statistics for a particular
LANswitch port.

Indexes

No indexes recorded

Column	Syntax	OID
lsPortExtendedStatsNumber mandatory The monitored port.The value of this item is: 16*(S-1)+P, where S is the slot number in the hub (1..16) and P the port within the slot (1..N).	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.3.3.6.1.1`
lsPortCreationOrder mandatory An index that defines the relative ordering of the discovery time of ports captured for a particular lsPortControlEntry. This index shall be between 1 and N, where N is the value of the associated lsPortControlTableSiz…	Integer32	`.1.3.6.1.4.1.81.19.3.3.6.1.2`
lsPortIndex mandatory The set of collected port statistics of which this entry is a part. The set of ports identified by a particular value of this index is associated with the lsPortControlEntry as identified by the same value of lsPortCon…	Integer32	`.1.3.6.1.4.1.81.19.3.3.6.1.3`
lsPortOutPkts mandatory The number of packets without errors transmitted from the LANswitch bus to this port.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.6.1.4`
lsPortInBroadcastPkts mandatory The number of good Ethernet packets directed towards the broadcast address that were transmitted to the LANswitch bus through this port.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.6.1.5`
lsPortInMulticastPkts mandatory The number of good Ethernet packets directed to a multicast address that were transmitted to the LANswitch bus through this port.	RFC1155-SMICounter Constraints: `range: 0-440` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.3.6.1.6`

lsHostFilterTable

table mandatory

.1.3.6.1.4.1.81.19.3.4 · 1 row entry · 2 columns

Open in standard view

A list of hosts to be monitored on the high-speed
bus by the RMON MIB hosts group. The OID of this 
table is a legitimate value for the hostControlDataSource.
The size of the table is limited to 200 entries.

lsHostFilterEntry entry .1.3.6.1.4.1.81.19.3.4.1

An entry in the filter table.

Indexes

ethTopMACFindBus

Column	Syntax	OID
lsHostFilterAddress mandatory The MAC address of a host monitored on the high-speed bus.	OctetString	`.1.3.6.1.4.1.81.19.3.4.1.1`
lsHostFilterStatus mandatory The status of this lsHostFilter entry. When the status is valid, the host defined in the corresponding lsHostFilter is a part of the filter.	Enumerationr/w Constraints: `range: 0-48`	`.1.3.6.1.4.1.81.19.3.4.1.2`

lsHostPortFilterTable

table mandatory

.1.3.6.1.4.1.81.19.3.6 · 1 row entry · 2 columns

Open in standard view

A list of ports to be monitored on the high-speed bus.
The OID of this table is a legitimate value for the 
hostControlDataSource.
When this OID is a source for the host table, a port in the 
table has the same meaning as an instruction to the agent to 
collect statistics for all the hosts connected to that port.
The size of this table is limited to 5 entries.

lsHostPortFilterEntry entry .1.3.6.1.4.1.81.19.3.6.1

An entry in the filter table.

Indexes

ethTopLSAId

Column	Syntax	OID
lsHostPortFilter mandatory The port monitored on the LANswitch bus. The value of this item is: 16*(S-1)+P, where S is the slot number in the hub (1..16) and P the port within the slot (1..N).	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.3.6.1.1`
lsHostPortFilterStatus mandatory The status of this lsHostPortFilter entry. When the status is valid, the hosts defined by the corresponding lsHostPortFilter are a part of the filter.	Enumerationr/w Constraints: `range: 384-384`	`.1.3.6.1.4.1.81.19.3.6.1.2`

lsMatrixFilterTable

table mandatory

.1.3.6.1.4.1.81.19.3.8 · 1 row entry · 2 columns

Open in standard view

A list of hosts to be monitored on the high-speed bus 
by the RMON MIB matrix group. The OID of this table is a 
legitimate value for the hostControlDataSource.
The size of the table is limited to 200 entries.

lsMatrixFilterEntry entry .1.3.6.1.4.1.81.19.3.8.1

An entry in the filter table.

Indexes

ethTopBus

Column	Syntax	OID
lsMatrixFilterAddress mandatory The MAC address of a host monitored on the high-speed bus.	OctetString	`.1.3.6.1.4.1.81.19.3.8.1.1`
lsMatrixFilterStatus mandatory The status of this lsMatrixFilter entry. When the status is valid, the hosts defined by the corresponding lsMatrixFilter are a part of the filter.	Enumerationr/w Constraints: `range: 6-6`	`.1.3.6.1.4.1.81.19.3.8.1.2`

lsHostTimePortCorrTable

table mandatory

.1.3.6.1.4.1.81.19.3.10 · 1 row entry · 4 columns

Open in standard view

An addition to the RMON MIBs hostTimeTable. This table contains
a list of MAC addresses that were monitored on the high-speed bus
and the switch ports to which they are connected.
The index of this table is the same as for the standard RMON
hostTimeTable. Indexes are hostTimeCreationOrder and hostTimeIndex.
The MAC address is stored in hostTimeAddress.
The port to which the MAC address is connected
hostTimePortConnection.

lsHostTimePortCorrEntry entry .1.3.6.1.4.1.81.19.3.10.1

An entry in the MAC to port correlation table.

Indexes

alarmMonitorStatusIndex

Column	Syntax	OID
hostTimeAddress mandatory The physical address of this host.	OctetString Constraints: `range: 1-65535`	`.1.3.6.1.4.1.81.19.3.10.1.1`
hostTimeCreationOrder mandatory An index that uniquely identifies an entry in the hostTime table among those entries associated with the same hostControlEntry. This index shall be between 1 and N, where N is the value of the associated hostControlTab…	Integer32	`.1.3.6.1.4.1.81.19.3.10.1.2`
hostTimeIndex mandatory The set of collected host statistics of which this entry is a part. The set of hosts identified by a particular value of this index is associated with the hostControlEntry as identified by the same value of hostControl…	Integer32	`.1.3.6.1.4.1.81.19.3.10.1.3`
hostTimePortConnection mandatory The switch port to which this hostTimeAddress is connected. The coding of the port number varies for different hubs and packplanes. For the LANSwitch HSB the value of this item is: The value of this item is: 32*(S…	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.3.10.1.4`

lsHistoryTable

table mandatory

.1.3.6.1.4.1.81.19.3.11 · 1 row entry · 23 columns

Open in standard view

A list of High Speed Bus history entries.

lsHistoryEntry entry .1.3.6.1.4.1.81.19.3.11.1

An historical sample of LANswitch statistics on a HSB.
This sample is associated with the historyControlEntry which set up
the parameters for a regular collection of these samples.

Indexes

No indexes recorded

Column	Syntax	OID
lsHistoryIndex mandatory The history of which this entry is a part. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.	Integer32 Constraints: `range: 0-2147483647` Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.3.11.1.1`
lsHistorySampleIndex mandatory An index that uniquely identifies the particular sample this entry represents among all samples associated with the same lshistoryControlEntry. This index starts at 1 and increases by one as each new sample is taken.	Integer32	`.1.3.6.1.4.1.81.19.3.11.1.2`
lsHistoryIntervalTime mandatory The value of sysUpTime when this bucket was sampled .	RFC1155-SMITimeTicks Textual Convention: RFC1155-SMITimeTicks `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.3`
lsHistoryStatsDropEvents mandatory The total number of events in which packets were dropped by the probe due to lack of resources. Note that this number is not necessarily the number of packets dropped; it is just the number of times this condition has …	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.4`
lsHistoryStatsPkts mandatory The total number of packets (including error packets) received on the LANswitch bus.	RFC1155-SMICounter Constraints: `range: 1-65535` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.5`
lsHistoryStatsOctets mandatory The total number of octets of data (including those in bad packets) received on the LANswitch bus (excluding framing bits but including FCS octets).	RFC1155-SMICounter Constraints: `range: 1-2147483647` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.6`
lsHistoryStatsEthBroadcastPkts mandatory The total number of good Ethernet packets received that were directed to the broadcast address.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.7`
lsHistoryStatsEthMulticastPkts mandatory The total number of good packets received that were directed to a multicast address. Note that this number does not include packets directed to the broadcast address.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.8`
lsHistoryStatsGoodEthPkts mandatory The total number of good Ethernet packets received on the LANswitch bus.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.9`
lsHistoryStatsGoodEthOctets mandatory The total number of octets that were received on the LANswitch bus in good Ethernet packets (excluding framing bits but including FCS octets).	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.10`
lsHistoryStatsBadEthPkts mandatory The total number of bad Ethernet packets received on the LANswitch bus.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.11`
lsHistoryStatsBadEthOctets mandatory The total number of octets that were received on the LANswitch bus in bad Ethernet packets (excluding framing bits but including FCS octets).	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.12`
lsHistoryStatsNonEthPkts mandatory The total number of packets received on the LANswitch bus in non Ethernet packets.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.13`
lsHistoryStatsNonEthOctets mandatory The total number of octets that were received on the LANswitch bus in non Ethernet packets (excluding framing bits but including FCS octets).	RFC1155-SMICounter Constraints: `range: 1-65535` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.14`
lsHistoryStatsPriority1Pkts mandatory The total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.	RFC1155-SMICounter Constraints: `range: 1-2147483647` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.15`
lsHistoryStatsPriority1Octets mandatory The total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.16`
lsHistoryStatsPriority2Pkts mandatory The total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.17`
lsHistoryStatsPriority2Octets mandatory The total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.18`
lsHistoryStatsPriority3Pkts mandatory The total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.19`
lsHistoryStatsPriority3Octets mandatory The total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.20`
lsHistoryStatsPriority4Pkts mandatory The total number of packets (including error packets) received on the LANswitch bus whose priority is that defined for this entry.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.21`
lsHistoryStatsPriority4Octets mandatory The total number of octets (including error packets) received on the LANswitch bus whose packets have the priority defined for this entry.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.3.11.1.22`
lsHistoryBusUtilization mandatory The utilization of the LANswitch bus, expressed in percents of the maximum LANswitch traffic possible.	Integer32	`.1.3.6.1.4.1.81.19.3.11.1.23`

lstIntPortTable

table mandatory

.1.3.6.1.4.1.81.19.4.1.1 · 1 row entry · 36 columns

Open in standard view

lstIntPortEntry entry .1.3.6.1.4.1.81.19.4.1.1.1

An entry in the table, containing data about
a LANswitch port of LANswitch Token-Ring modules.

Indexes

No indexes recorded

Column	Syntax	OID
lstIntPortGroupId mandatory Id of the group to which the switch port belongs.	Integer32	`.1.3.6.1.4.1.81.19.4.1.1.1.1`
lstIntPortId mandatory Switch port Id in module	Integer32	`.1.3.6.1.4.1.81.19.4.1.1.1.2`
lstIntPortSidebandMode mandatory Enable Sideband mode on internal port. In this mode, MAC level management of all rings can be done.	Enumerationr/w	`.1.3.6.1.4.1.81.19.4.1.1.1.3`
lstIntPortTotalOctets mandatory Total number of octets circling in the ring. It is the sum of local octets, in octets and out octets.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.4.1.1.1.4`
lstIntPortTotalTraffic mandatory Total traffic in ring as part of the maximum possible utilization, 4Mbps or 16Mbps, expressed in percents. It is the sum of local traffic, in traffic and out traffic.	Integer32	`.1.3.6.1.4.1.81.19.4.1.1.1.5`
lstIntPortLocalOctets mandatory Number of octets local to the ring. The local traffic includes only traffic between stations on the local ring.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.4.1.1.1.6`
lstIntPortLocalTraffic mandatory Local traffic in ring as part of the maximum possible utilization, 4Mbps or 16Mbps, expressed in percents. The local traffic includes only traffic between stations on the local ring.	Integer32	`.1.3.6.1.4.1.81.19.4.1.1.1.7`
lstIntPortInOctets mandatory Number of octets passing in to the HSB from the ring. The In traffic includes only traffic going from stations on the local ring to stations on other rings.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.4.1.1.1.8`
lstIntPortInTraffic mandatory In traffic to the HSB from the ring as part of the maximum possible utilization, 4Mbps or 16Mbps, expressed in percents. The In traffic includes only traffic going from stations on the local ring to stations on othe…	Integer32	`.1.3.6.1.4.1.81.19.4.1.1.1.9`
lstIntPortOutOctets mandatory Number of octets passing out from the HSB to the ring. The Out traffic includes only traffic going to stations on the local ring from stations on other rings.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.4.1.1.1.10`
lstIntPortOutTraffic mandatory Out traffic from the HSB to the ring as part of the maximum possible utilization, 4Mbps or 16Mbps, expressed in percents. The Out traffic includes only traffic going to stations on the local ring from stations on o…	Integer32 Constraints: `range: 32-32`	`.1.3.6.1.4.1.81.19.4.1.1.1.11`
lstIntPortTotalFrames mandatory Total number of frames in the ring.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.4.1.1.1.12`
lstIntPortLostFrames mandatory Number of lost frames because of Back Pressure.	RFC1155-SMICounter Constraints: `range: 32-32` Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.4.1.1.1.13`
lstIntPortClaimFrames mandatory Number of Claim-Token frames in the ring.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.4.1.1.1.16`
lstIntPortPurgeFrames mandatory Number of Ring-Purge frames in the ring.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.19.4.1.1.1.17`
lstIntPortNormallyCloseOpen mandatory Defines the IO mode of the switch port: normally close or normally open. When the port is in 'normallyOpen' mode, all packets enter the port regardless to CAM content.	Enumerationr/w	`.1.3.6.1.4.1.81.19.4.1.1.1.18`
lstIntPortSlicingEnable mandatory Packet slicing mechanism for decreasing the delay of packets transmission in the HSB. Value 'on' enables the slicing mechanism.	Enumerationr/w Constraints: `range: 6-6`	`.1.3.6.1.4.1.81.19.4.1.1.1.19`
lstIntPortSliceLength mandatory The slice length in bytes. It determines the delay of packet's transmission through the HSB.	Integer32r/w Constraints: `range: 1-4095` Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.4.1.1.1.20`
lstIntPortUNAddr mandatory MAC address of the Upstream Neighbor of the line interface.	OctetString Constraints: `range: 1-4095`	`.1.3.6.1.4.1.81.19.4.1.1.1.21`
lstIntPortMACAddress mandatory MAC address of the line interface.	OctetString	`.1.3.6.1.4.1.81.19.4.1.1.1.22`
lstIntPortSMPTransmitEnable mandatory Enable SMP MAC frame transmission by line interface during single-station situation.	Enumerationr/w	`.1.3.6.1.4.1.81.19.4.1.1.1.23`
lstIntPortIPGLength mandatory Number of bytes interval between frames transmission of the line interface to the ring.	Integer32r/w	`.1.3.6.1.4.1.81.19.4.1.1.1.24`
lstIntPortBPDummyWindow mandatory The time (in 0.25ms) between Dummy frames sendings during Back Pressure situation of the line interface.	Integer32r/w	`.1.3.6.1.4.1.81.19.4.1.1.1.25`
lstIntPortBPTokenWindow mandatory The time (in 0.25ms) until Token release during Back Pressure situation of the line interface.	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.4.1.1.1.26`
lstIntPortTransmitWindow mandatory The time (in 0.25ms) of line interface transmission until Token release.	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.4.1.1.1.27`
lstIntPortBlockingPriority mandatory The priority of the line interface during Back Pressure situation.	Integer32r/w	`.1.3.6.1.4.1.81.19.4.1.1.1.28`
lstIntPortNormalPriority mandatory The priority of the line interface for HSB packets transmission into the ring.	Integer32r/w Constraints: `range: 0-36`	`.1.3.6.1.4.1.81.19.4.1.1.1.29`
lstIntPortDummyMV mandatory Content of MV (Major Vector) field in Dummy frame during Back Pressure of line interface.	Integer32r/w	`.1.3.6.1.4.1.81.19.4.1.1.1.30`
lstIntPortTxConsecutiveBusiesThresh mandatory The threshold of the number of consecutive busies counter.	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.4.1.1.1.31`
lstIntPortTxBufFullThresh mandatory Threshold indicator for frames buffer full.	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.4.1.1.1.32`
lstIntPortRxEmpty0 mandatory Upper threshold pointer of Rx buffer. Determines the degree of buffer overflow and back pressure efficiency.	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.4.1.1.1.33`
lstIntPortRxEmpty1 mandatory Middle threshold pointer of Rx buffer. Determines the degree of buffer overflow and back pressure efficiency..	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.4.1.1.1.34`
lstIntPortRxEmpty2 mandatory Lower threshold pointer of Rx buffer. Determines the degree of buffer overflow and back pressure efficiency.	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.4.1.1.1.35`
lstIntPortRxFull mandatory Rx full threshold pointer. Determines the degree of buffer overflow and back pressure efficiency.	Integer32r/w Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.4.1.1.1.36`
lstIntPortBPEnable mandatory Enable/disable the Back Pressure mechanism.	Enumerationr/w	`.1.3.6.1.4.1.81.19.4.1.1.1.37`
lstIntPortRouteSideband mandatory Set the internal port ability to get from the HSB sideband packets. The value 'on' enables the routing of sideband packet from the HSB into the internal port.	Enumerationr/w	`.1.3.6.1.4.1.81.19.4.1.1.1.38`

lseWANTable

table mandatory

.1.3.6.1.4.1.81.19.5 · 1 row entry · 3 columns

Open in standard view

LAN Switch WAN data table. Implementation of this table is
mandatory for all LANswitch modules with WAN ports.

lseWANEntry entry .1.3.6.1.4.1.81.19.5.1

Entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
lseWANGroupId mandatory Slot number in which the module is located.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.5.1.1`
lseWANPortId mandatory WAN port index.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.5.1.2`
lseWANConnection mandatory WAN connection status.	Enumeration	`.1.3.6.1.4.1.81.19.5.1.3`

vnsPacketTable

table mandatory

.1.3.6.1.4.1.81.19.7.1 · 1 row entry · 14 columns

Open in standard view

VNS packets data table. Implementation of this table is
mandatory for 3LS (3rd layer switch) module.

vnsPacketEntry entry .1.3.6.1.4.1.81.19.7.1.1

Entry in the table.

Indexes

No indexes recorded

Column	Syntax	OID
vnsPacketMACAddress mandatory The Mac Address of the sending station.	OctetString	`.1.3.6.1.4.1.81.19.7.1.1.1`
vnsPacketProtocolTypeMask mandatory This is a mask of the exising protocols. Bit(0)='1' when IP protocol exist and '0' otherwise, Bit(1)='1' when IPX protocol exist and '0' otherwise, all other bits are '0' for the moment.	OctetString	`.1.3.6.1.4.1.81.19.7.1.1.2`
vnsPacketIPAddress mandatory The IP address of the packet's sending station. In case the typeaddress is not IP this field will be 0.0.0.0.	RFC1155-SMIIpAddress Textual Convention: RFC1155-SMIIpAddress `OctetString` Type Constraints: `range: 4`	`.1.3.6.1.4.1.81.19.7.1.1.3`
vnsPacketIPNetMask mandatory The IP Address Mask from the IP Interface Table.	RFC1155-SMIIpAddress Textual Convention: RFC1155-SMIIpAddress `OctetString` Type Constraints: `range: 4`	`.1.3.6.1.4.1.81.19.7.1.1.4`
vnsPacketIPXnetwork mandatory The IPX NetWork Address of the packet's sending station. In case that the typeaddress is not IPX this field will be 0.0.0.0.	OctetString	`.1.3.6.1.4.1.81.19.7.1.1.5`
vnsPacketStationType mandatory The Station Type indicates from where comes the packets in the case of the IPX protocol.	Enumeration	`.1.3.6.1.4.1.81.19.7.1.1.6`
vnsPacketPortGroupId mandatory Index which identifies the group inside the chassis for which this entry contains information. It equals with the slot number.	Integer32	`.1.3.6.1.4.1.81.19.7.1.1.7`
vnsPacketPortId mandatory Index which identifies the port inside the group for which this entry contains information. It equals with the port number.	Integer32	`.1.3.6.1.4.1.81.19.7.1.1.8`
vnsPacketBackbonePort mandatory The value 2 indicates that the port source of the packet is a backbone port.	Enumeration	`.1.3.6.1.4.1.81.19.7.1.1.9`
vnsPacketExpectedVLAN mandatory The value of this item is the VLAN number that the packet had to have according to it's address.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.7.1.1.10`
vnsPacketDetectedVLAN mandatory The value of this item is the detected VLAN number of the arrived packet.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.19.7.1.1.11`
vnsPacketBoxAgentIP mandatory The IP Address of the Hub's BoxAgent where the 3LS (3rd layer switch) module exist.	RFC1155-SMIIpAddress Textual Convention: RFC1155-SMIIpAddress `OctetString` Type Constraints: `range: 4`	`.1.3.6.1.4.1.81.19.7.1.1.12`
vnsPacketExpectedIfName mandatory The value of this item is the name of the interface the packet was expected to be received on according to it's address.	RFC1213-MIBDisplayString Textual Convention: RFC1213-MIBDisplayString `OctetString`	`.1.3.6.1.4.1.81.19.7.1.1.13`
vnsPacketDetectedIfName mandatory The value of this item is the name of the interface the packet was actually received on.	RFC1213-MIBDisplayString Textual Convention: RFC1213-MIBDisplayString `OctetString`	`.1.3.6.1.4.1.81.19.7.1.1.14`

ethTopMessageResultTable

table mandatory

.1.3.6.1.4.1.81.23.3.4 · 1 row entry · 2 columns

Open in standard view

A table that contains 3 items with the results of the topology messages received by the  agent.

ethTopMessageResultEntry entry .1.3.6.1.4.1.81.23.3.4.1

An entry in the table, containing part of the received data.

Indexes

No indexes recorded

Column	Syntax	OID
ethTopMessageResultId mandatory The table's index. Can assume the values 1,2, or 3.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.23.3.4.1.1`
ethTopMessageResult mandatory A row in the Topology Messages result table. Each row contains up to 44 elements.	OctetString	`.1.3.6.1.4.1.81.23.3.4.1.2`

ethTopMACFindResultTable

table mandatory

.1.3.6.1.4.1.81.23.3.6 · 1 row entry · 2 columns

Open in standard view

A table that contains 4 rows with the results of the MACFind process. Each row contains 	the results for one of the hub's buses. The number of items supported is equal to the 	number of buses supported by the agent.

ethTopMACFindResultEntry entry .1.3.6.1.4.1.81.23.3.6.1

An entry in the table, containing one LSA item.

Indexes

No indexes recorded

Column	Syntax	OID
ethTopMACFindBus mandatory The bus for which the results are reported.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.23.3.6.1.1`
ethTopMACFindResult mandatory The results of the search for the requested MAC addresses fo the relevant bus. The format is: MAC (6 bytes), slot (1 byte), port (1 byte). If the Agent doesn't find a MAC's correlation, the slot and port will be '0'.	OctetString	`.1.3.6.1.4.1.81.23.3.6.1.2`

ethTopLSATable

table mandatory

.1.3.6.1.4.1.81.23.3.7 · 1 row entry · 2 columns

Open in standard view

A table that contains 8 rows with the last source addresses found on the hub's ports. 
Each row in the table reports the last source addresses for specific slots in the hub:
#1: modules 1,2,17,18;	#5: modules 9,10,25, 26;
#2: modules 3,4,19,20;	#6: modules 11,12,27, 28;
#3: modules 5,6,21,22;	#7: modules 13,14,29,30;
#4: modules 7,8,23,24;	#8: modules 15,16,31,32; 
The data in the items appears by the slot order defined above. All 8 items exist even if 	some of them are empty.

ethTopLSAEntry entry .1.3.6.1.4.1.81.23.3.7.1

An entry in the table, containing one LSA item.

Indexes

No indexes recorded

Column	Syntax	OID
ethTopLSAId mandatory The table's index. Assumes values 1,2,3,...,8.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.23.3.7.1.1`
ethTopLSA mandatory This item contains the last source addresses for modules in related slots. For each port the data is: slot (one byte), port (one byte), address (6 bytes). For none existing ports the LSA will be 0. The first bit (MSB) …	OctetString	`.1.3.6.1.4.1.81.23.3.7.1.2`

ethTopAddressTable

table mandatory

.1.3.6.1.4.1.81.23.3.8 · 1 row entry · 2 columns

Open in standard view

A table that contains the MAC addresses used by the agent for the topology
messages.

ethTopAddressEntry entry .1.3.6.1.4.1.81.23.3.8.1

An entry in the topology address table. The number of entries is
equal to the number of Ethernet
buses supported by the agent.

Indexes

No indexes recorded

Column	Syntax	OID
ethTopBus mandatory The bus for which this address is defined.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.23.3.8.1.1`
ethTopAddress mandatory The MAC address used by the agent for the topology discovery process on the related bus.	OctetStringr/w	`.1.3.6.1.4.1.81.23.3.8.1.2`

alarmMonitorStatusTable

table mandatory

.1.3.6.1.4.1.81.30.1.1 · 1 row entry · 2 columns

Open in standard view

A list of alarms status for Alarm entries.

alarmMonitorStatusEntry entry .1.3.6.1.4.1.81.30.1.1.1

Each entry contains an index (appropriate to specific alarmIndex item)
and the alarmed status of this alarm entry

Indexes

No indexes recorded

Column	Syntax	OID
alarmMonitorStatusIndex mandatory An index that uniquely identifies an entry in the alarmMonitorStatusTable. This index is the same as the appropriate alarm Table.	Integer32	`.1.3.6.1.4.1.81.30.1.1.1.1`
alarmMonitorStatus mandatory The alarms' status for the appropriate alarm table 1 - ok 2 - alarmState.	Enumeration	`.1.3.6.1.4.1.81.30.1.1.1.2`

portHistoryExtendedControlTable

table mandatory

.1.3.6.1.4.1.81.30.3.1 · 1 row entry · 4 columns

Open in standard view

A list of extended history control entries.

portHistoryExtendedControlEntry entry .1.3.6.1.4.1.81.30.3.1.1

A list of extended parameters that set up a periodic sampling of statistics.

Indexes

No indexes recorded

Column	Syntax	OID
portHistoryExtendedControlCreateTime mandatory The value of sysUpTime at the creation of the control row and start of the history collection index with the same value of the historyControlIndex.	RFC1155-SMITimeTicks Textual Convention: RFC1155-SMITimeTicks `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.1.1.1`
portHistoryExtendedControlLastBucketIndex mandatory The index of the last bucket that was stored to the history table.	Integer32 Textual Convention: COPS-PR-SPPIInteger32 `Integer32` Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.81.30.3.1.1.2`
portHistoryExtendedControlNumberOfBuckets mandatory The number of buckets stored in the probe.	Integer32	`.1.3.6.1.4.1.81.30.3.1.1.3`
portHistoryExtendedControlName mandatory The name of the this history collection.	RFC1213-MIBDisplayStringr/w Textual Convention: RFC1213-MIBDisplayString `OctetString`	`.1.3.6.1.4.1.81.30.3.1.1.4`

lsPortHistoryTable

table mandatory

.1.3.6.1.4.1.81.30.3.2 · 1 row entry · 7 columns

Open in standard view

A list of LANswitch port history entries.

lsPortHistoryEntry entry .1.3.6.1.4.1.81.30.3.2.1

An historical sample of port switch statistics with the historyControlEntry,
which set up the parameters for a regular collection of these samples.

Indexes

No indexes recorded

Column	Syntax	OID
lsPortHistoryIndex mandatory The history of which this entry is a part. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.	Integer32	`.1.3.6.1.4.1.81.30.3.2.1.1`
lsPortHistorySampleIndex mandatory An index that uniquely identifies the particular sample, this entry represents among all samples associated with the same lshistoryControlEntry. This index starts at 1 and increases by one as each new sample is taken.	Integer32	`.1.3.6.1.4.1.81.30.3.2.1.2`
lsPortHistoryIntervalTime mandatory The value of sysUpTime at the start of the interval over which this sample was measured.	RFC1155-SMITimeTicks Textual Convention: RFC1155-SMITimeTicks `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.2.1.3`
lsPortHistoryBoxConfiguration mandatory Octet String build by concatenating the genGroupType of the maximum 16 modules in the LANSwitch box. By reading this variable a management application can draw a list of the LANSwitch modules and ports configuration re…	OctetString	`.1.3.6.1.4.1.81.30.3.2.1.4`
lsPortHistoryPkts mandatory The total number of good packets received on the port.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.2.1.5`
lsPortHistoryCollisions mandatory The best estimate of the total number of collisions on this port during this sampling interval.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.2.1.6`
lsPortHistoryTotalErrors mandatory The total number of errors detected by the switching hardware on this port, including FCS errors and too long packets.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.2.1.7`

scPortHistoryTable

table mandatory

.1.3.6.1.4.1.81.30.3.3 · 1 row entry · 9 columns

Open in standard view

A list of Xswitch port history entries.

scPortHistoryEntry entry .1.3.6.1.4.1.81.30.3.3.1

An historical sample of port switch statistics with the historyControlEntry,
which set up the parameters for a regular collection of these samples.

Indexes

No indexes recorded

Column	Syntax	OID
scPortHistoryIndex mandatory The history of which this entry is a part. The history identified by a particular value of this index is the same history as identified by the same value of historyControlIndex.	Integer32	`.1.3.6.1.4.1.81.30.3.3.1.1`
scPortHistorySampleIndex mandatory An index that uniquely identifies the particular sample, this entry represents among all samples associated with the same scHistoryControlEntry. This index starts at 1 and increases by one as each new sample is taken.	Integer32	`.1.3.6.1.4.1.81.30.3.3.1.2`
scPortHistoryIntervalTime mandatory The value of sysUpTime at the start of the interval over which this sample was measured.	RFC1155-SMITimeTicks Textual Convention: RFC1155-SMITimeTicks `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.3.1.3`
scPortHistoryBoxConfiguration mandatory Octet String build by concatenating the genGroupType of the maximum 14 modules in the Meritage box or 4 boxes in the Visage stack. By reading this variable a management application can draw a list of the modules (box…	OctetString	`.1.3.6.1.4.1.81.30.3.3.1.4`
scPortHistoryGoodPktsRec mandatory The total number of good packets received by the port.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.3.1.5`
scPortHistoryGoodNonUnicastPktsRec mandatory The total number of good packets received that were directed to multicat or broadcast address.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.3.1.6`
scPortHistoryCollisions mandatory The best estimate of the total number of collisions on the Ethernet segment connected to the port.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.3.1.7`
scPortHistoryBadPkts mandatory The total number of bad packets filtered by the port. This item is the summation of: scEthPortCRCAlignErrors, scEthPortOversizePkts, scEthPortFragments and scEthPortJabber.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.3.1.8`
scPortHistoryGoodPktsSent mandatory The total number of good packets sent by the port.	RFC1155-SMICounter Textual Convention: RFC1155-SMICounter `Unsigned32` Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.81.30.3.3.1.9`