lseGroupWorkState

APPLIC-MIB · .1.3.6.1.4.1.81.19.1.1.1.21

Object

column mandatory Enumeration

One of the possible states of the module: this item
indicates if the module is runing or booting. The value
runAndBoot(3) indicates a serious software problem.

Context

MIB: APPLIC-MIB
OID: .1.3.6.1.4.1.81.19.1.1.1.21
Type: column
Access: readonly
Status: mandatory
Parent: lseGroupEntry
Table: lseGroupTable
Siblings: 24

Syntax

Enumeration

Values & Constraints

No enumerated values or constraints recorded.

Related Objects

Sibling Objects

Object	Type	Syntax	OID
lseGroupId mandatory Slot number in which the group is installed.	column	Integer32	`.1.3.6.1.4.1.81.19.1.1.1.1`
lseGroupActiveMonitor mandatory This attribute defines the module which is the high-speed bus active monitor.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.10`
lseGroupBackbone12 mandatory Port 1 and 2 in the board perform as Backbone link. lse208 - upper cluster is RX only and lower cluster is TX only. lse404 - upper port is Rx only and second port is Tx only. Two …	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.11`
lseGroupSetDefaults mandatory Set all hardware parameters to their default values. This item will always return a value of off(2), since it acts like a toggle switch.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.12`
lseGroupBackbone34 mandatory Port 3 and 4 in the board performed as Backbone link. lse404 - Third port is Rx only and forth port is Tx only. Two remaining ports performed as regular foirl interfaces.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.13`
lseGroupBackboneRedun12 mandatory Value on(1) of this attribute defines a redundancy (backup) relationship between Backbone port 1 and backbone port 2 on a LANswiltch module.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.14`
lseGroupBackoffFromJam mandatory Value on(1) of this attribute defines non-consecutive jam after a collision has occured in LANswitch modules.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.15`
lseGroupCAMClear mandatory Value on(1) of this attribute causes the LANSwitch module to clear the CAM tables.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.16`
lseGroupJamPrevent mandatory Jam prevent flag. Functionaly, Jam prevent is a back-pressure into the line direction. There are two modes of opration: 1) automatic - the sensor gets the items status from HW 2) …	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.17`
lseGroupNormOpCl mandatory Normaly Open/Close flag. When open(1) state is set, the sensor should activate a delay mechanism for the module to operate at Normaly-Closed mode for 30 seconds in order to enable…	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.18`
lseGroupNormOpDelay mandatory When sets to a value greater than 0 (zero) and the MIB item lseGroupNormOpCl is equal to closed(2), this item define the time delay that the module will remain in normally open …	column	Integer32	`.1.3.6.1.4.1.81.19.1.1.1.19`
lseGroupFastOpen mandatory Setting the value of this attribute to ON activates the port for short idle time when code violation was detected.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.2`
lseGroupAutoPartitionEnable mandatory Enables autopartition mechanism support in the group level for each port of the group.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.20`
lseGroupBITResult mandatory The Bit Indication Test in state 'faulty' indicates a problem. The agent should send a fault trap in this case.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.22`
lseGroupAssignSlots mandatory In a multi-backbone configuration within a single HUB, this item enables to assign backbone module with specific slot numbers. Only packets from these slots should be handled by…	column	OctetString	`.1.3.6.1.4.1.81.19.1.1.1.23`
lseGroupHSBMonStatus mandatory This is a bit-masked attribute which displays events which may cause HSB Reset. When a bit is '1', the relevant evet may cause HSB Reset. When a bit is '0', the relevant evet will…	column	Integer32	`.1.3.6.1.4.1.81.19.1.1.1.24`
lseGroupEnableHSBReset mandatory This item enables/disables the HSB Reset mechanism in the module.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.25`
lseGroup10MSqlt mandatory Setting the value of this attribute to ON activates the mechanism of detection preamble of 10Mhz.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.3`
lseGroupSmartSqlt obsolete Control the mechnism of the input sensitivity of the port.	column	Enumeration	`.1.3.6.1.4.1.81.19.1.1.1.4`
lseGroupCParameter mandatory Defines the number of consecutive collisions the port waits before it ceases transmitting of 512 bits time toward the station.	column	Integer32	`.1.3.6.1.4.1.81.19.1.1.1.5`
lseGroupIPGJamLength mandatory Defines the IPG jam length in Ethernet bit time (100nS) start at 16 bit time in steps of 16, to 112 bit time. For LFE-100, (Fast Ethernet bit time (10nS)) values are from 48 bi…	column	Integer32	`.1.3.6.1.4.1.81.19.1.1.1.6`
lseGroupJamLength mandatory Defines the Jam Length in time starting from 8 (800micro-seconds) to 120 (12mili-seconds). Each step of 8 is equal 800micro-seconds. For LFE-100, values are from 8 (80micro-secon…	column	Integer32	`.1.3.6.1.4.1.81.19.1.1.1.7`
lseGroupDataBlinderLength mandatory Defines the Data Blinder Length in Ethernet bit time (100nS) start at 16 bit time in steps of 16 to 112 bit time. For LFE-100, (Fast Ethernet bit time (10nS)) values are from 0…	column	Integer32	`.1.3.6.1.4.1.81.19.1.1.1.8`
lseGroupIPGDataLength mandatory Defines the IPG (Inter Packet Gap) length in Ethernet bit time (100nS) starting at 16 bit time in steps of 16 to 112 bit time. For LFE-100, (Fast Ethernet bit time (10nS)) values…	column	Integer32	`.1.3.6.1.4.1.81.19.1.1.1.9`

Indexes