lseGroupSmartSqlt
APPLIC-MIB ·
.1.3.6.1.4.1.81.19.1.1.1.4
Object
column
obsolete
r/w
Enumeration
Control the mechnism of the input sensitivity of the port.
Context
- MIB
- APPLIC-MIB
- OID
.1.3.6.1.4.1.81.19.1.1.1.4- Type
- column
- Access
- readwrite
- Status
- obsolete
- Parent
- lseGroupEntry
- Table
- lseGroupTable
- Siblings
- 24
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| lseGroupId mandatory Slot number in which the group is installed. | column | Integer32 | .1.3.6.1.4.1.81.19.1.1.1.1 |
| lseGroupActiveMonitor mandatory This attribute defines the module which is the high-speed bus active monitor. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.10 |
| lseGroupBackbone12 mandatory Port 1 and 2 in the board perform as Backbone link.
lse208 - upper cluster is RX only and lower cluster is TX only.
lse404 - upper port is Rx only and second port is Tx only. Two … | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.11 |
| lseGroupSetDefaults mandatory Set all hardware parameters to their default values. This item will
always return a value of off(2), since it acts like a toggle switch. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.12 |
| lseGroupBackbone34 mandatory Port 3 and 4 in the board performed as Backbone link.
lse404 - Third port is Rx only and forth port is Tx only.
Two remaining ports performed as regular foirl interfaces. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.13 |
| lseGroupBackboneRedun12 mandatory Value on(1) of this attribute defines a redundancy (backup)
relationship between Backbone port 1 and backbone port 2
on a LANswiltch module. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.14 |
| lseGroupBackoffFromJam mandatory Value on(1) of this attribute defines non-consecutive
jam after a collision has occured in LANswitch modules. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.15 |
| lseGroupCAMClear mandatory Value on(1) of this attribute causes the LANSwitch
module to clear the CAM tables. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.16 |
| lseGroupJamPrevent mandatory Jam prevent flag.
Functionaly, Jam prevent is a back-pressure into the line direction.
There are two modes of opration:
1) automatic - the sensor gets the items status from HW
2) … | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.17 |
| lseGroupNormOpCl mandatory Normaly Open/Close flag.
When open(1) state is set, the sensor should activate
a delay mechanism for the module to operate at Normaly-Closed
mode for 30 seconds in order to enable… | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.18 |
| lseGroupNormOpDelay mandatory When sets to a value greater than 0 (zero) and the MIB item
lseGroupNormOpCl is equal to closed(2), this item define the time
delay that the module will remain in normally open … | column | Integer32 | .1.3.6.1.4.1.81.19.1.1.1.19 |
| lseGroupFastOpen mandatory Setting the value of this attribute to ON activates the port for short idle time
when code violation was detected. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.2 |
| lseGroupAutoPartitionEnable mandatory Enables autopartition mechanism support in the group level for each port of the group. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.20 |
| lseGroupWorkState mandatory One of the possible states of the module: this item
indicates if the module is runing or booting. The value
runAndBoot(3) indicates a serious software problem. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.21 |
| lseGroupBITResult mandatory The Bit Indication Test in state 'faulty' indicates a problem.
The agent should send a fault trap in this case. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.22 |
| lseGroupAssignSlots mandatory In a multi-backbone configuration within a single HUB, this item enables to assign
backbone module with specific slot numbers. Only packets from these slots should be
handled by… | column | OctetString | .1.3.6.1.4.1.81.19.1.1.1.23 |
| lseGroupHSBMonStatus mandatory This is a bit-masked attribute which displays events which may cause HSB Reset.
When a bit is '1', the relevant evet may cause HSB Reset.
When a bit is '0', the relevant evet will… | column | Integer32 | .1.3.6.1.4.1.81.19.1.1.1.24 |
| lseGroupEnableHSBReset mandatory This item enables/disables the HSB Reset mechanism in the module. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.25 |
| lseGroup10MSqlt mandatory Setting the value of this attribute to ON activates the mechanism of detection
preamble of 10Mhz. | column | Enumeration | .1.3.6.1.4.1.81.19.1.1.1.3 |
| lseGroupCParameter mandatory Defines the number of consecutive collisions the port waits before it ceases transmitting
of 512 bits time toward the station. | column | Integer32 | .1.3.6.1.4.1.81.19.1.1.1.5 |
| lseGroupIPGJamLength mandatory Defines the IPG jam length in Ethernet bit time (100nS) start at 16 bit time in
steps of 16, to 112 bit time.
For LFE-100, (Fast Ethernet bit time (10nS)) values are from 48 bi… | column | Integer32 | .1.3.6.1.4.1.81.19.1.1.1.6 |
| lseGroupJamLength mandatory Defines the Jam Length in time starting from 8 (800micro-seconds) to
120 (12mili-seconds). Each step of 8 is equal 800micro-seconds.
For LFE-100, values are from 8 (80micro-secon… | column | Integer32 | .1.3.6.1.4.1.81.19.1.1.1.7 |
| lseGroupDataBlinderLength mandatory Defines the Data Blinder Length in Ethernet bit time (100nS) start at 16 bit time in steps of
16 to 112 bit time.
For LFE-100, (Fast Ethernet bit time (10nS)) values are from 0… | column | Integer32 | .1.3.6.1.4.1.81.19.1.1.1.8 |
| lseGroupIPGDataLength mandatory Defines the IPG (Inter Packet Gap) length in Ethernet bit time
(100nS) starting at 16 bit time in steps of 16 to 112 bit time.
For LFE-100, (Fast Ethernet bit time (10nS)) values… | column | Integer32 | .1.3.6.1.4.1.81.19.1.1.1.9 |