lseIntPortResetSwitchCAM
APPLIC-MIB ·
.1.3.6.1.4.1.81.19.1.2.1.1.4
Object
column
mandatory
r/w
Enumeration
Acting like toggle switch thus always returns off(2) on read. When set to on(1), causes the reset of the LANswitch CAM (addresses) memory.
Context
- MIB
- APPLIC-MIB
- OID
.1.3.6.1.4.1.81.19.1.2.1.1.4- Type
- column
- Access
- readwrite
- Status
- mandatory
- Parent
- lseIntPortEntry
- Table
- lseIntPortTable
- Siblings
- 45
Syntax
Enumeration
Values & Constraints
No enumerated values or constraints recorded.
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| lseIntPortGroupId mandatory Id of the group to which the port belongs. | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.1 |
| lseIntPortRoutingMode mandatory generic(1) - examines all the packets that are
not members of any virtual network.
net(2) - examines only the packets that have
the port's network number.
allPackets(4) - examine… | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.10 |
| lseIntPortGlobal mandatory Setting the global mode to on(1) sets the
port in a network routing mode that examines
all packets that are not members of all virtual networks. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.11 |
| lseIntPortLearnIOCAM mandatory Setting this parameter to on(1) enables an I/O port to
learn incoming MAC addresses received in its port and
store them in its CAM. Packets with destination address
that match th… | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.12 |
| lseIntPortSecurity mandatory Setting the value of this attribute to on(1) activates the security mode. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.13 |
| lseIntPortIgnoreBusy mandatory Setting the value of this attribute to on(1) activates the ignore busy mode.
The busy signal toward the high-speed bus is not activated even though the TX buffer is full. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.14 |
| lseIntPortRetryPriorityLevel1 mandatory The port increases the priority level of the high-speed bus packets after the defined number
(0..31) trials. | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.15 |
| lseIntPortRetryPriorityLevel2 mandatory The port increases the priority level of the high-speed bus packets after the defined number
(0..255) trials. | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.16 |
| lseIntPortRetryPriorityLevel3 mandatory The port increases the priority level of the high-speed bus packets after the defined number
(0..255) trials. | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.17 |
| lseIntPortIgnoreProtocolType mandatory Any packet regardless of the protocol type is received from the high-speed bus. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.18 |
| lseIntPortCompanyMAC mandatory The attribute defines the first three bytes of the MAC address of the video host server. | column | OctetString | .1.3.6.1.4.1.81.19.1.2.1.1.19 |
| lseIntPortId mandatory Number of LanSwitch port in the board. | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.2 |
| lseIntPortTxSafetyZone mandatory Defines the Tx Safety Zone in bits. | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.20 |
| lseIntPortRxSafetyZone mandatory Defines the Rx Safety Zone in bits. | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.21 |
| lseIntPortTxBurstLength mandatory Defines the TX Burst Length in bits. | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.22 |
| lseIntPortSecurityIntruder mandatory The value on(1) of this attribute reflects a security violation occurrence. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.23 |
| lseIntPortJabber mandatory Value on(1) of this attribute reflects that jabber was transmitted
to the port by the high-speed bus. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.24 |
| lseIntPortCAM mandatory 112 bytes of MAC addresses. Each contains one
byte of the port number and six bytes of the MAC
address. This enables to send 16 MAC Addresses
( 16*7=112 bytes) | column | OctetString | .1.3.6.1.4.1.81.19.1.2.1.1.25 |
| lseIntPortVideoStateMachine mandatory Setting the value of this attribute to on(1) activates the video state machine mode.
Received packets are filtered by demand from the station. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.26 |
| lseIntPortTransmitWeight mandatory Defines the Transmit Weight of the frames for the current LANswitch port toward
the high - speed bus. | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.27 |
| lseIntPortSuperPriority mandatory Setting the value of this attribute to on(1) activates the retry priority functions. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.28 |
| lseIntPortAlignment mandatory The number of alignment errors observed on a specified port. | column | RFC1155-SMICounter | .1.3.6.1.4.1.81.19.1.2.1.1.29 |
| lseIntPortIOMode mandatory on(1) activates IO mode in which all packets on the
high-speed bus that were not captured by any regular
port are captured by the I/O port. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.3 |
| lseIntPortRxReject obsolete The number of Rx buffer full observed on a specified port, from the line toward the
High-speed bus. | column | RFC1155-SMICounter | .1.3.6.1.4.1.81.19.1.2.1.1.30 |
| lseIntPortTxReject obsolete The number of Tx buffer full observed on a specified port, from the line toward the
High-speed bus. | column | RFC1155-SMICounter | .1.3.6.1.4.1.81.19.1.2.1.1.31 |
| lseIntPortRxEmpty0 mandatory Define the highest threshold to receive packets from the HSB.
This parameter is relevant when the receive buffer is full.
When the buffer reached this threshold, all packets will … | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.32 |
| lseIntPortRxEmpty1 mandatory Define the middle threshold to receive packets from the HSB.
This parameter is relevant when the receive buffer is almost full.
When the buffer reached this threshold, the only pa… | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.33 |
| lseIntPortRxEmpty2 mandatory Define the lowest threshold to receive packets from the HSB.
This parameter is relevant when the receive buffer is almost full.
When the buffer reached this threshold, the only pa… | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.34 |
| lseIntPortSuperNetNumber mandatory If the internal port supports SuperNet mode, the user
have to define the supernet number. Default value is 0.
Change of this number when the internal port is Generic,
Global or … | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.35 |
| lseIntPortGlobalSuperNet mandatory An internal port that is part of all SuperNets is set to
Global SuperNet routing. The SuperNet number is 15
in this case. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.36 |
| lseIntPortMACAddress mandatory The MAC address of the port, if it has. If not, an octet
string of length 0. | column | OctetString | .1.3.6.1.4.1.81.19.1.2.1.1.37 |
| lseIntPortIgnoreRoutingMode mandatory When this parameter is 'ignore', the LANSwitch
port monitors all packets without paying attention
to the virtual net assignment. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.38 |
| lseIntPortCAMLastChange mandatory This attribute contains the value of sysUpTime
at the time any change occured to the
content of the specific CAM. | column | RFC1155-SMITimeTicks | .1.3.6.1.4.1.81.19.1.2.1.1.39 |
| lseIntPortCopiedPort mandatory The port monitored on the LANswitch bus by the
LSE-PM module. The value of this item is: 32*(S-1)+P,
where S is the slot number in the hub and P the port
within the slot (1.. 3… | column | Integer32 | .1.3.6.1.4.1.81.19.1.2.1.1.40 |
| lseIntPortBroadcastBehavior mandatory This item relates only to LSE-PM modules. The value of
this item defines the method by which the module treats
broadcast and multicast packets. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.41 |
| lseIntPortFilteringMethod mandatory This item is relevant only to the LSE-PM module.
The value of this item defines the filtering method
used to capture packets from the Cellenium bus to
the Ethernet connection. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.42 |
| lseIntPortSetFilter mandatory This item is relevant only to the LSE-PM module.
The item is used to add new addresses to the module's
filtering table. The string is a sequence of MAC addresses,
6 bytes each. … | column | OctetString | .1.3.6.1.4.1.81.19.1.2.1.1.43 |
| lseIntPortRemoveFilter mandatory This item is relevant only to the LSE-PM module.
The item is used to remove existing addresses from
the module's filtering table. The string is a sequence of
MAC addresses, 6 b… | column | OctetString | .1.3.6.1.4.1.81.19.1.2.1.1.44 |
| lseIntPortClearFilter mandatory This item is relevant only to the LSE-PM module.
The item acts as a toggle switch: when its value is set
to clear(2), the contents of the module's filtering
tables are cleared.
… | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.45 |
| lseIntPortMonitorMissedEvents mandatory This item is relevant only to LSE-PM modules. The value
of the counter is the number of packets that were not
captured by the port as a result of overload on the
Ethernet line,… | column | RFC1155-SMICounter | .1.3.6.1.4.1.81.19.1.2.1.1.46 |
| lseIntPortVideoPacket mandatory When set to on(1), all Tx packets toward the
high-speed bus to video type packets. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.5 |
| lseIntPortPriorityStateMachine mandatory Setting the value of this attribute to on(1) activates
the priority mechanism. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.6 |
| lseIntPortActiveBroadcastPriority mandatory Setting the value of this attribute to on(1) activates
the active broadcast mode in priority mechanism. | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.7 |
| lseIntPortPriorityLevel mandatory This attribute defines the priority levels of
Tx packets toward the high-speed bus.
The highest priority is broadcast(1). | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.8 |
| lseIntPortSuperPriorityEnable mandatory When limited space is left in Tx buffer, only the highest priority
packets are accepted. This in turn can create a situation in which one
port tries to send a packet and never… | column | Enumeration | .1.3.6.1.4.1.81.19.1.2.1.1.9 |